Experimental and Numerical Analysis of Different Volutes in a Centrifugal Compressor

In a centrifugal compressor the flow around the diffuser is collected and led to the pipe system by a spiral-shaped volute. In this study a single-stage centrifugal compressor with three different volutes is investigated. The compressorwas first equipped with the original volute, the cross-section of which was a combination of a rectangle and semi-circle. Next a new volute with a fully circular cross-section was designed and manufactured. Finally, the circular volute wasmodified by rounding the tongue and smoothing the tongue area. The overall performance of the compressor as well as the static pressure distribution after the impeller and on the volute surface were measured. The flow entering the volute was measured using a three-hole Cobra-probe, and flow visualisations were carriedout in the exit cone of the volute. In addition, the radial force acting on theimpeller was measured using magnetic bearings. The complete compressor with thecircular volute (inlet pipe, full impeller, diffuser, volute and outlet pipe) was also modelled using computational fluid dynamics (CFD). A fully 3-D viscous flow was solved using a Navier-Stokes solver, Finflo, developed at Helsinki University of Technology. Chien's k-e model was used to take account of the turbulence. The differences observed in the performance of the different volutes were quite small. The biggest differences were at low speeds and high volume flows,i.e. when the flow entered the volute most radially. In this operating regime the efficiency of the compressor with the modified circular volute was about two percentage points higher than with the other volutes. Also, according to the Cobra-probe measurements and flow visualisations, the modified circular volute performed better than the other volutes in this operating area. The circumferential static pressure distribution in the volute showed increases at low flow, constant distribution at the design flow and decrease at high flow. The non-uniform static pressure distribution of the volute was transmitted backwards across the vaneless diffuser and observed at the impeller exit. At low volume flow a strong two-wave pattern developed into the static pressure distribution at the impeller exit due to the response of the impeller to the non-uniformity of pressure. The radial force of the impeller was the greatest at the choke limit, the smallest atthe design flow, and moderate at low flow. At low flow the force increase was quite mild, whereas the increase at high flow was rapid. Thus, the non-uniformityof pressure and the force related to it are strong especially at high flow. Theforce caused by the modified circular volute was weaker at choke and more symmetric as a function of the volume flow than the force caused by the other volutes.

A cultura do coco: uma análise econômica

O coqueiro é uma planta de clima tropical, sendo cultivado em cerca de 90 países, destacando-se o continente asiático na produção e comercialização do produto in natura e nos subprodutos. Podem-se aproveitar diversas partes da planta, como o fruto, as folhas, a inflorescência, entre outros produtos e subprodutos. O Brasil possui condições especiais que favorecem a adaptação e o desenvolvimento da cultura do coco. Dentre as principais regiões brasileiras produtoras, o Nordeste destaca-se, produzindo cerca de 80% de toda a produção nacional. A Bahia destaca-se como um dos principais produtores e consumidores. O município de Ilhéus vem expandindo a produção ao longo do tempo, em função do fluxo de turistas e de iniciativas de diversificar a agricultura regional. O objetivo deste estudo é identificar e avaliar, econômica e financeiramente, os diferentes níveis tecnológicos adotados pelos produtores de coco no município de Ilhéus. Neste estudo, utilizou-se de levantamento de corte seccional (cross-section) para o qual foram aplicados vinte questionários junto aos produtores, selecionados por meio do critério de amostra intencional, segundo a técnica survey. Por meio dessas informações, foram calculados os indicadores financeiros (VPL, TIR, B/C) e a análise de sensibilidade. Nota-se que os três níveis tecnológicos adotados no município apresentam receitas positivas; no entanto, a tecnologia III é a que se mostra mais eficiente. Os resultados, para as tecnologias I, II e III, do VPL são de R$ 4.857,04; R$ 20.782,38, e R$ 47.931,22, respectivamente; para a TIR, de 43%, 80% e 87%, sucessivamente. A relação B/C foi de 2,32 (Tecnologia I), 3,24 (Tecnologia II) e 2,89 (Tecnologia III). Tais resultados indicam que as tecnologias adotadas são econômica e financeiramente viáveis. No entanto, o produtor poderia realizar maior exploração do potencial da atividade, gerando maior lucratividade.

Characterisation of the LMS200 laser beam under the influence of blockage surfaces. Influence on 3D scanning of tree orchards

The geometric characterisation of tree orchards is a high-precision activity comprising the accurate measurement and knowledge of the geometry and structure of the trees. Different types of sensors can be used to perform this characterisation. In this work a terrestrial LIDAR sensor (SICK LMS200) whose emission source was a 905-nm pulsed laser diode was used. Given the known dimensions of the laser beam cross-section (with diameters ranging from 12 mm at the point of emission to 47.2 mm at a distance of 8 m), and the known dimensions of the elements that make up the crops under study (flowers, leaves, fruits, branches, trunks), it was anticipated that, for much of the time, the laser beam would only partially hit a foreground target/object, with the consequent problem of mixed pixels or edge effects. Understanding what happens in such situations was the principal objective of this work. With this in mind, a series of tests were set up to determine the geometry of the emitted beam and to determine the response of the sensor to different beam blockage scenarios. The main conclusions that were drawn from the results obtained were: (i) in a partial beam blockage scenario, the distance value given by the sensor depends more on the blocked radiant power than on the blocked surface area; (ii) there is an area that influences the measurements obtained that is dependent on the percentage of blockage and which ranges from 1.5 to 2.5 m with respect to the foreground target/object. If the laser beam impacts on a second target/object located within this range, this will affect the measurement given by the sensor. To interpret the information obtained from the point clouds provided by the LIDAR sensors, such as the volume occupied and the enclosing area, it is necessary to know the resolution and the process for obtaining this mesh of points and also to be aware of the problem associated with mixed pixels.

V0 production in p+A collisions at √s = 41.6 GeV

Inclusive doubly differential cross sections d 2 σ pA /dx F   dp T 2 as a function of Feynman-x (x F ) and transverse momentum (p T ) for the production of K S 0 , Λ and Λ¯ in proton-nucleus interactions at 920 GeV are presented. The measurements were performed by HERA-B in the negative x F range (−0.12cross sections are presented and discussed. The Cronin effect is clearly observed for all three V 0 species. The atomic number dependence is parameterized as σ pA =σ pN ⋅A α where σ pN is the proton-nucleon cross section. The measured values of α are all near one. The results are compared with EPOS 1.67 and PYTHIA 6.3. EPOS reproduces the data to within ≈20% except at very low transverse momentum.

The measurement of ice velocity, mass balance and thinning-rate on Johnsons Glacier, Livingston Island, South Shetland Islands, Antarctica

A network of twenty stakes was set up on Johnsons Glacier in order to determine its dynamics. During the austral summers from 1994-95 to 1997-98, we estimated surface velocities, mass balances and ice thickness variations. Horizontal velocity increased dow nstream from 1 m a- 1 near the ice divides to 40 m a- 1 near the ice terminus. The accumulation zone showed low accumulation rates (maximum of 0,6 m a- 1 (ice)), whereas in the lower part of the glacier, ablation rates were 4,3 m a- 1 (ice). Over the 3-year study period, both in the accumulation and ablation zones, we detected a reduction in the ice surface level ranging from 2 to 10 m from the annual ve rt ical velocities and ice-thinning data, the mass balance was obtained and compared with the mass balance field values, resulting in similar estimates. Flux values were calculated using cross-section data and horizontal velocities, and compared with the results obtained by means of mass balance and ice thinning data using the continuity equation. The two methods gave similar results.

DATA WAREHOUSING IN A GLOBAL METAL INDUSTRIAL COMPANY

Työn tavoittena oli selvittää, miten tietovarastointi voi tukea yrityksessä tapahtuvaa päätöksentekoa. Tietovarastokomponenttien ja –prosessien kuvauksen jälkeen on käsitelty tietovarastoprojektin eri vaiheita. Esitettyä teoriaa sovellettiin käytäntöön globaalissa metalliteollisuusyrityksessä, jossa tietovarastointikonseptia testattiin. Testauksen perusteella arvioitiin olemassa olevan tiedon tilaa sekä kahden käytetyn ohjelmiston toimivuutta tietovarastoinnissa. Yrityksen operatiivisten järjestelmien tiedon laadun todettiin olevan tutkituilta osin epäyhtenäistä ja puutteellista. Siksi tiedon suora yrityslaajuinen hyödyntäminen luotettavien ja hyvälaatuisten raporttien luonnissa on vaikeaa. Lisäksi eri yksiköiden välillä havaittiin epäyhtenäisyyttä käytettyjen liiketoiminnan käsitteiden sekä järjestelmien käyttötapojen suhteen. Testauksessa käytetyt ohjelmistot suoriutuivat perustietovarastoinnista hyvin, vaikkakin joitain rajoituksia ja erikoisuuksia ilmenikin. Työtä voidaan pitää ennen varsinaista tietovarastoprojektia tehtävänä esitutkimuksena. Jatkotoimenpiteinä ehdotetaan testauksen jatkamista nykyisillä työkaluilla kohdistaen tavoitteet konkreettisiin tuloksiin. Tiedon laadun tärkeyttä tulee korostaa koko organisaatiossa ja olemassa olevan tiedon laatua pitää parantaa tulevaisuudessa.

Clinical management and burden of bipolar disorder: a multinational longitudinal study (WAVE-bd Study)

BACKGROUND: Studies in bipolar disorder (BD) to date are limited in their ability to provide a whole-disease perspective--their scope has generally been confined to a single disease phase and/or a specific treatment. Moreover, most clinical trials have focused on the manic phase of disease, and not on depression, which is associated with the greatest disease burden. There are few longitudinal studies covering both types of patients with BD (I and II) and the whole course of the disease, regardless of patients' symptomatology. Therefore, the Wide AmbispectiVE study of the clinical management and burden of Bipolar Disorder (WAVE-bd) (NCT01062607) aims to provide reliable information on the management of patients with BD in daily clinical practice. It also seeks to determine factors influencing clinical outcomes and resource use in relation to the management of BD. METHODS: WAVE-bd is a multinational, multicentre, non-interventional, longitudinal study. Approximately 3000 patients diagnosed with BD type I or II with at least one mood event in the preceding 12 months were recruited at centres in Austria, Belgium, Brazil, France, Germany, Portugal, Romania, Turkey, Ukraine and Venezuela. Site selection methodology aimed to provide a balanced cross-section of patients cared for by different types of providers of medical aid (e.g. academic hospitals, private practices) in each country. Target recruitment percentages were derived either from scientific publications or from expert panels in each participating country. The minimum follow-up period will be 12 months, with a maximum of 27 months, taking into account the retrospective and the prospective parts of the study. Data on demographics, diagnosis, medical history, clinical management, clinical and functional outcomes (CGI-BP and FAST scales), adherence to treatment (DAI-10 scale and Medication Possession Ratio), quality of life (EQ-5D scale), healthcare resources, and caregiver burden (BAS scale) will be collected. Descriptive analysis with common statistics will be performed. DISCUSSION: This study will provide detailed descriptions of the management of BD in different countries, particularly in terms of clinical outcomes and resources used. Thus, it should provide psychiatrists with reliable and up-to-date information about those factors associated with different management patterns of BD. TRIAL REGISTRATION NO: ClinicalTrials.gov: NCT01062607.

1.48 and 1.84 µm thulium emissions in monoclinic KGd(WO4)2 single crystals

By exciting at 788 nm, we have characterized the near infrared emissions of trivalent thulium ions in monoclinic KGd(WO4)2 single crystals at 1.48 and 1.84 mm as a function of dopant concentration from 0.1% to 10% and temperature from 10 K to room temperature. We used the reciprocity method to calculate the maximum emission cross-section of 3.0310220 cm2 at 1.838 mm for the polarization parallel to the Nm principal optical direction. These results agrees well with the experimental data. Experimental decay times of the 3H4!3F4 and 3F4!3H6 transitions have been measured as a function of thulium concentration.

Painatuksen UV-stabiilisuuden optimointi fenolihartsatussa paperissa

Tässä diplomityössä tutkittiin painetun paperin ja siitä fenoliformaldehydihartsilla impregnoimalla valmistetun pinnoituskalvon UV-stabiilisuuden parantamis-mahdollisuuksia. Työn kirjallisuusosassa käsitellään painetun pinnoituskalvon valmistusprosessia ja painatuksen UV-valonkestoon vaikuttavia tekijöitä. Painovärin pigmentti, sen määrä ja käsittely, painovärin sideaine sekä fenoliformaldehydihartsi ja sen lisäaineet vaikuttavat pinnoitetun betonoimisvanerin säänkesto-ominaisuuksiin. Erilaisilla epäorgaanisilla valkoisilla pigmenteillä ja kidemuodoilla on erilainen UV-valonkesto ja taitekerroin. Päällystämällä titaanidioksidi esimerkiksi alumiini- tai zirkoniumoksideilla sen UV-valonkestoa voidaan parantaa merkittävästi. UV-hajoaminen voidaan havaita painetun pinnoitteen liituuntumisena. Liituuntumista voidaan pitää veden ja hapen välisenä reaktiona, jota titaanidioksidi ja UV-säteily katalysoivat. Sen takia myös muiden valkoisten epäorgaanisten pigmenttien ominaisuuksia ja käyttöä selvitettiin. Kokeissa käytettiin yhdeksää eri painoväriä, kahta eri paksuista paperia ja kahta eri tyyppistä hartsia. Painovärejä ohennettiin vedellä ja paperin painopuolta vaihdeltiin. Kaikissa painatuksissa käytettiin kolmea eri rasterointiasteen laattaa, jolloin painovärin määrää paperissa saatiin vähennettyä. Painetuista papereista mitattiin densiteetti, värimäärä, pisara-absorptio vedellä ja kontaktikulma hartsilla. Myös painovärin tunkeumaa selvitettiin paperin poikkileikeistä tehtyjen SEM-kuvien avulla. Painetut paperit impregnoitiin fenoliformaldehydihartsilla kalvoksi. Pinnoituskalvot puristettiin vanerin pinnalle laboratoriopuristimella. Koekappaleet altistettiin UV-valolle, sateelle ja pakkaselle sääkaapissa 400 h ajan, mikä vastaa noin 1,5 vuotta ulkona Suomen oloissa. Kappaleista mitattiin kiilto, värinmuutos ja liituuntuminen. Pinnoitteen liituuntumista tapahtui vähiten niissä koepisteissä, joissa painatus oli tehty 30 % rasteroidulla laatallaSäänkestävä TiO2 osoittautui hyväksi, mutta myös ZnO-pigmentillä saatiin hyviä tuloksia. ZnO-koepisteessä liituuntumisreaktio ei ole niin voimakkaasti katalysoitu kuin TiO2-koepisteissä. Paksun paperin painatuspuolella näytti olevan merkitystä säänkestoon. Huopapuolelle painettuna pinnoitteen liituuntuminen oli vähäisempää

Integrin-Specific Mechanoresponses to Compression and Extension Probed by Cylindrical Flat-Ended AFM Tips in Lung Cells

Cells from lung and other tissues are subjected to forces of opposing directions that are largely transmitted through integrin-mediated adhesions. How cells respond to force bidirectionality remains ill defined. To address this question, we nanofabricated flat-ended cylindrical Atomic Force Microscopy (AFM) tips with ~1 µm2 cross-section area. Tips were uncoated or coated with either integrin-specific (RGD) or non-specific (RGE/BSA) molecules, brought into contact with lung epithelial cells or fibroblasts for 30 s to form focal adhesion precursors, and used to probe cell resistance to deformation in compression and extension. We found that cell resistance to compression was globally higher than to extension regardless of the tip coating. In contrast, both tip-cell adhesion strength and resistance to compression and extension were the highest when probed at integrin-specific adhesions. These integrin-specific mechanoresponses required an intact actin cytoskeleton, and were dependent on tyrosine phosphatases and Ca2+ signaling. Cell asymmetric mechanoresponse to compression and extension remained after 5 minutes of tip-cell adhesion, revealing that asymmetric resistance to force directionality is an intrinsic property of lung cells, as in most soft tissues. Our findings provide new insights on how lung cells probe the mechanochemical properties of the microenvironment, an important process for migration, repair and tissue homeostasis.

Momentum dependence of the phi-meson nuclear transparency

The production of φ mesons in proton collisions with C, Cu, Ag, and Au targets has been studied via the φ → K + K − decay at an incident beam energy of 2.83 GeV using the ANKE detector system at COSY. For the first time, the momentum dependence of the nuclear transparency ratio, the in-medium φ width, and the differential cross section for φ -meson production at forward angles have been determined for these targets over the momentum range of 0.6-1.6 GeV /c. There are indications of a significant momentum dependence in the value of the extracted φ width, which corresponds to an effective φN absorption cross section in the range of 14-21 mb.

Teräspalkkirakenteiden palomitoitus hiilivetypalossa

Työn tavoitteena oli kehittää teräspalkkirakenteiden palosuunnittelua ja palosuojauksen toteutusta öljynjalostamolla käytettävien kantavien teräspalkkirakenteiden osalta. Lisäksi tavoitteena oli luoda suunnitteluohjeen runko palomitoituksen toteuttamiseksi Neste Engineering Oy:ssä. Ongelmakohtia työssä olivat rakenteiden kapasiteettien tarkka määritys, toimivien toteutusratkaisujen etsiminen, sekä öljynjalostamolla mitoituspalona käytettävän hiilivetypalon SFS-ENV-1992-1-2 käyttö yleisemmin mitoituspalona käytettävän standardipalo ISO-834 sijaan. Työssä perehdyttiin kirjallisuuden perusteella eri palosuojausmenetelmiin. Tarkemman jatkotutkimuksen kohteeksi otettiin jo käytössä hyväksi havaittu teräsputkipalkkien sisäpuoleinen betonitäyttö. Menetelmässä teräsputkipalkin oletetaan kantavan kuormat normaalitilassa ja sisällä olevan raudoitetun betonin palossa. Palkkirakenteiden kapasiteettimitoitus määritettiin laskennallisesti poikkileikkauksille. Mitoitus perustuu palkissa tapahtuvien sisäisten venymien ja puristumien tarkasteluun, sekä poikkileikkauksen tarkan lämpötilajakauman huomioimiseen. Raudoitustankojen ankkurointia palkki-pilari-liitoksessa kehitettiin valmistuksen kannalta yksioikoisemmaksi ja helpommin toteutettavaksi. Palkkien raudoituksiin suunniteltiin kierremuhvijatkoksella toteutettava ankkurointimenetelmä, jolla palkkien raudoitustangot saadaan ankkuroitua täydestä kapasiteetistaan tapauskohtaisesti pilarin vastakkaisella puolella olevaan palkkiin tai ankkurointikappaleella pilariin. Teräsputkipilarin betonivalun vaihtoehtoisiin menetelmiin tutustuttiin. Pilarin alapäähän asennettavan venttiilin läpi tapahtuva täyttö helpottaa betonointityövaihetta. Tutkimuksen tuloksena luotiin suunnitteluohjeen runko, jonka pohjalta voidaan tehdä lopullinen ohje. Myös työn tuloksena saatu laskentaohjelma palkkien momentti-kapasiteetin ja pilarin nurjahduskuorman laskemiseksi helpottaa suunnittelua. Raudoituksen ankkurointiin ja betonointiin esitettyjen menetelmien toimivuus on syytä kokeilla käytännössä ja tehdä jatkokehitys näistä saatavien kokemusten pohjalta.

Quality of Disease Management and Risk of Mortality in English Primary Care Practices

OBJECTIVE: To investigate whether better management of chronic conditions by family practices reduces mortality risk. DATA: Two random samples of 5 million patients registered with over 8,000 English family practices followed up for 4 years (2004/5-2007/8). Measures of the quality of disease management for 10 conditions were constructed for each family practice for each year. The outcome measure was an indicator taking the value 1 if the patient died during a specified year, 0 otherwise. STUDY DESIGN: Cross-section and multilevel panel data multiple logistic regressions were estimated. Covariates included age, gender, morbidity, hospitalizations, attributed socio-economic characteristics, and local health care supply measures. PRINCIPAL FINDINGS: Although a composite measure of the quality of disease management for all 10 conditions was significantly associated with lower mortality, only the quality of stroke care was significant when all 10 quality measures were entered in the regression. CONCLUSIONS: The panel data results suggest that a 1 percent improvement in the quality of stroke care could reduce the annual number of deaths in England by 782 [95 percent CI: 423, 1140]. A longer study period may be necessary to detect any mortality impact of better management of other conditions.

1.84 micron emission of Tm3+ sensitized by Yb3+ ions in monoclinic KGd(WO4)2 single crystals

By exciting at 940 nm, we have characterized the 1.84 m near infrared emission of trivalent thulium ions in Yb3+, Tm3+:KGd WO4 2 single crystals as a function of the dopant concentration and temperature, from 10 K to room temperature. An overall 3H6 Stark splitting of 470 cm−1 for the Tm3+ ions in the Yb3+, Tm3+:KGd WO4 2 was obtained. We also studied the blue emission at 476 nm Tm3+ and the near infrared emissions at 1.48 m Tm3+ and 1 m Yb3+ as a function of the dopant concentration. Experimental decay times of the 1G4, 3H4, and 3F4 Tm3+ and 2F5/2 Yb3+ excited states have been measured as a function of Yb3+ and Tm3+ ion concentrations. For the 3F4 →3H6 transition of Tm3+ ions, we used the reciprocity method to calculate the maximum emission cross section of 3.07 10−20 cm2 at 1.84 m for the polarization parallel to the Nm principal optical direction.

Fluid flow in T-junction of pipes

The aim of this work is to study flow properties at T-junction of pipe, pressure loss suffered by the flow after passing through T-junction and to study reliability of the classical engineering formulas used to find head loss for T-junction of pipes. In this we have compared our results with CFD software packages with classical formula and made an attempt to determine accuracy of the classical formulas. In this work we have studies head loss in T-junction of pipes with various inlet velocities, head loss in T-junction of pipes when the angle of the junction is slightly different from 90 degrees and T-junction with different area of cross-section of the main pipe and branch pipe. In this work we have simulated the flow at T-junction of pipe with FLUENT and Comsol Multiphysics and observed flow properties inside the T-junction and studied the head loss suffered by fluid flow after passing through the junction. We have also compared pressure (head) losses obtained by classical formulas by A. Vazsonyi and Andrew Gardel and formulas obtained by assuming T-junction as combination of other pipe components and observations obtained from software experiments. One of the purposes of this study is also to study change in pressure loss with change in angle of T-junction. Using software we can have better view of flow inside the junction and study turbulence, kinetic energy, pressure loss etc. Such simulations save a lot of time and can be performed without actually doing the experiment. There were no real life experiments made, the results obtained completely rely on accuracy of software and numerical methods used.