Photoproduction of charged pion pairs from hydrogen at photon energies between 800 and 1500 MeV

The reaction γ + p p + π⁺ + π^- has been studied for photon energies between 800 and 1500 MeV and for dipion masses between 510 and 900 MeV. The bremsstrahlung beam from the Caltech synchrotron was passed through a liquid hydrogen target and spark chambers were used to detect the three final particles. In addition, the proton energy was determined by a range measurement. Approximately 40,000 photographs were taken, yielding 3018 acceptable events. The results were fit to an incoherent combination of the N*(1238) resonance, the p^o (750) resonance, and three-body phase space, with various models being tried for p^o production. The total cross section for p^o production is consistent with previous experiments. However, the angular dependence of the cross section is slightly more peaked in the forward direction, and the ratio of p^o production to phase space production is larger than previously observed.

However, since this experiment was only sensitive to the production angles cos θ cm ≥ .75, statistical fluctuations and/or an anisotropic distribution of background production have a severe influence on the p^o to background ratio. Of the p^o models tested, the results prefer p^o production by the one pion exchange mechanism with a very steep form factor dependence. The values of the mass and width of the p^o found here are consistent with previous experiments.

Mass spectrometry coupled to imaging techniques: The better the view the greater the challenge

These are definitively exciting times for membrane lipid researchers. Once considered just as the cell membrane building blocks, the important role these lipids play is steadily being acknowledged. The improvement occurred in mass spectrometry techniques (MS) allows the establishment of the precise lipid composition of biological extracts. However, to fully understand the biological function of each individual lipid species, we need to know its spatial distribution and dynamics. In the past 10 years, the field has experienced a profound revolution thanks to the development of MS-based techniques allowing lipid imaging (MSI). Images reveal and verify what many lipid researchers had already shown by different means, but none as convincing as an image: each cell type presents a specific lipid composition, which is highly sensitive to its physiological and pathological state. While these techniques will help to place membrane lipids in the position they deserve, they also open the black box containing all the unknown regulatory mechanisms accounting for such tailored lipid composition. Thus, these results urges to different disciplines to redefine their paradigm of study by including the complexity revealed by the MSI techniques.

A model of the pelagic ecossystem in the eastern tropical Pacific Ocean

English: Recent calls for a more holistic approach to fisheries management have motivated development of trophic mass-balance models of ecosystems that underlie fisheries production. We developed a model hypothesis of the pelagic ecosystem in the eastern tropical Pacific Ocean (ETP) to gain insight into the relationships among the various species in the system and to explore the ecological implications of alternative methods of harvesting tunas. We represented the biomasses of and fluxes between the principal elements in the ecosystem with Ecopath, and examined the ecosystem's dynamic, time-series behavior with Ecosim. We parameterized the model for 38 species or groups of species, and described the sources, justifications, assumptions, and revisions of our estimates of the various parameters, diet relations, fisheries landings, and fisheries discards in the model. We conducted sensitivity analyses with an intermediate version of the model, for both the Ecopath mass-balance and the dynamic trajectories predicted by Ecosim. The analysis showed that changes in the basic parameters for two components at middle trophic levels, Cephalopods and Auxis spp., exert the greatest influence on the system. When the Cephalopod Q/B and Auxis spp. P/B were altered from their initial values and the model was rebalanced, the trends of the biomass trajectories predicted by Ecosim were not sensitive, but the scaling was sensitive for several components. We described the review process the model was subjected to, which included reviews by the IATTC Purse-seine Bycatch Working Group and by a working group supported by the National Center for Ecological Analysis and Synthesis. We fitted the model to historical time series of catches per unit of effort and mortality rates for yellowfin and bigeye tunas in simulations that incorporated historical fishing effort and a climate driver to represent the effect of El Niño-Southern Oscillation-scale variation on the system. The model was designed to evaluate the possible ecological implications of fishing for tunas in various ways. We recognize that a model cannot possibly represent all the complexity of a pelagic ocean ecosystem, but we believe that the ETP model provides insight into the structure and function of the pelagic ETP. Spanish: Llamamientos recientes hacia un enfoque más holístico al ordenamiento de la pesca han motivado el desarrollo de modelos tróficos de balance de masas de los ecosistemas que sostienen la producción pesquera. Desarrollamos una hipótesis modelo del ecosistema pelágico en el Océano Pacífico oriental tropical (POT) con miras a mejorar los conocimientos de las relaciones entre las distintas especies en el sistema y explorar las implicaciones ecológicas de métodos alternativos de capturar atunes. Con Ecopath representamos las biomasas de los elementos principales en el ecosistema, y los flujos entre los mismos, y con Ecosim examinamos el comportamiento dinámico del ecosistema con el tiempo. Parametrizamos el modelo para 38 especies o grupos de especies (denominados “componentes” del modelo), y describimos las fuentes, justificaciones, supuestos, y revisiones de nuestras estimaciones de los distintos parámetros, relaciones basadas en dieta, capturas retenidas de las pesquerías, y descartes de las mismas en el modelo. Realizamos análisis de sensibilidad con una versión intermedia del modelo, para el balance de masas de Ecopath y las trayectorias dinámicas predichas por Ecosim también. El análisis demostró que cambios en los parámetros básicos para dos componentes en niveles tróficos medianos, Cefalópodos y Auxis spp., ejercieron la mayor influencia sobre el sistema. Cuando se alteraron el Q/B de los Cefalópodos y el P/B de los Auxis spp. de sus valores iniciales y se balanceó el modelo de nuevo, las tendencias de las trayectorias de la biomasa predichas por Ecosim no fueron sensibles, pero la escala fue sensible para varios componentes. Describimos el proceso de revisión al que fue sujeto el modelo, inclusive revisiones por el Grupo de Trabajo sobre Captura Incidental de la CIAT y un grupo de trabajo apoyado por el Centro Nacional para Síntesis y Análisis Ecológicos. Ajustamos el modelo a series de tiempo históricas de capturas por unidad de esfuerzo y tasas de mortalidad de atunes aleta amarilla y patudo en simulaciones que incorporaron esfuerzo de pesca histórico e impulsos climáticos para representar el efecto de variaciones a escala de El Niño-Oscilación del Sur sobre el sistema. El modelo fue diseñado para evaluar las posibles implicaciones ecológicas de la pesca atunera de varias formas. Reconocemos la imposibilidad de que el modelo represente toda la complejidad de un ecosistema oceánico pelágico, pero creemos que el modelo del POT mejora los conocimientos de la estructura y función del POT pelágico.

Spectroscopic study of galaxies in the Herschel Reference Sample

Galaxies are clusters of millions and billions of stars dynamically stable, with gas, dust and dark matter. They are the biggest isolated objects known in the Universe . Even though they are very complex systems, today we have a clear knowledge about their evolution and about their physical phenomena. Aside from the stellar component there is a gaseous component, principally neutral Hydrogen (HI), and dust that, although is not a significant component in terms of the mass, plays an important role on the absorption phenomena. Finally, cinematic and other kind of observations suggest the existence of a spheric dark matter halo, dominant in terms of mass and more extensive than the barionic component.

Fish and habitat community assessments on North Carolina shipwrecks: potential sites for detecting climate change in the graveyard of the Atlantic

The Monitor National Marine Sanctuary (MNMS) was the nation’s first sanctuary, originally established in 1975 to protect the famous civil war ironclad shipwreck, the USS Monitor. Since 2008, sanctuary sponsored archeological research has branched out to include historically significant U-boats and World War II shipwrecks within the larger Graveyard of the Atlantic off the coast of North Carolina. These shipwrecks are not only important for their cultural value, but also as habitat for a wide diversity of fishes, invertebrates and algal species. Additionally, due to their unique location within an important area for biological productivity, the sanctuary and other culturally valuable shipwrecks within the Graveyard of the Atlantic are potential sites for examining community change. For this reason, from June 8-30, 2010, biological and ecological investigations were conducted at four World War II shipwrecks (Keshena, City of Atlanta, Dixie Arrow, EM Clark), as part of the MNMS 2010 Battle of the Atlantic (BOTA) research project. At each shipwreck site, fish community surveys were conducted and benthic photo-quadrats were collected to characterize the mobile conspicuous fish, smaller prey fish, and sessile invertebrate and algal communities. In addition, temperature sensors were placed at all four shipwrecks previously mentioned, as well as an additional shipwreck, the Manuela. The data, which establishes a baseline condition to use in future assessments, suggest strong differences in both the fish and benthic communities among the surveyed shipwrecks based on the oceanographic zone (depth). In order to establish these shipwrecks as sites for detecting community change it is suggested that a subset of locations across the shelf be selected and repeatedly sampled over time. In order to reduce variability within sites for both the benthic and fish communities, a significant number of surveys should be conducted at each location. This sampling strategy will account for the natural differences in community structure that exist across the shelf due to the oceanographic regime, and allow robust statistical analyses of community differences over time.

Analysis of four decades of high elevation climate data

Four decades of instrumented climate records at D1 on Niwot Ridge suggest that high elevation data are an important - and even unique - part of the full climate picture. High elevation data provide information on changing lapse rates as well as model verification for global warming, which is predicted to occur earliest in high latitudes and at high elevations. The D1 records show climatic trends that arguably support global warming, assuming that greater planetary wave amplitude is verification of warming. Lapse rates reflect conditions of air mass stability, atmospheric moisture, and could [sic] cover, which contribute to feedback processes involving temperature, precipitation, and snowpack. The D1 record show a period, 1981-1985, when the lapse rate increased significantly, and this change was not detected by other data.

The development of aerodynamic performance measurements in a transient test facility

Transient test facilities offer the potential for the simultaneous study of turbine aerodynamic performance, unsteady flow phenomena and the heat transfer characteristics of a turbine stage. This paper describes the development of aerodynamic performance measurement techniques in the Oxford Rotor Facility (ORF). The solutions to the technological issues involved with transient testing presented in this paper are expected to achieve levels of precision uncertainty comparable with traditional steady flow test rigs. The theoretical background to the measurement of aerodynamic performance is presented together with a comprehensive pre-test uncertainty analysis. The instrumentation scheme for the measurement of stage mass flow rate is discussed in detail, the measurements of shaft power, total inlet enthalpy, and stage pressure ratio are also outlined. The current working section features a 62% scale, 1-1/2 stage, high-pressure shroudless transonic turbine. The required inlet flow conditions are provided by an Isentropic Light Piston Tunnel (ILPT) with a quasi-steady state run time of approximately 70ms. The testing is conducted at engine representative specific speed, pressure ratio, gas-to-wall temperature ratio, Mach number and Reynolds number.

Feasibility study of biofuel production from freshwater fern, Azolla sp in Anzali Wetland

Production of bioethanol through acidic and enzymatic hydrolysis of aquatic Azolla sp., as a new source of bio-mass, has been performed, as a means to control increasing growth and reducing undesirable effects of this plant in Anzali lagoon. After sampling, drying and crushing, Azolla was hydrolyzed, using diluted acid and enzyme. Diluted acid hydrolysis was done using both autoclave and a high-pressure system (Batch Synth® Microwave synthesizer). The effects of temperature and time (in autoclave) and concentration of acid (in both) were compared. Cellubrix®, a ommercial cellulase source, was used for enzymatic hydrolysis process. The amounts of reducing sugars, glucose and furfural, released from hydrolyzate, were measured. To produce alcohol, Sacchromyces cerevisiae (to ferment sixcarbon sugars), Zygowilliopsis californica and Pichia stipitis (to ferment five-carbon and sixcarbon sugars) were used. Maximum amounts of glucose (4.83% w/w) and reducing sugars (14.15% w/w) were obtained using acid hydrolysis in autoclave. In the microwave oven, maximum glucose (5.04% w/w) and reducing sugars (13.27 w/w) were obtained at 180 and 200 °C, respectively. Under these conditions, maximum produced furfural was 1.54 g/L. The difference between amounts of furfural obtained from acid hydrolysis of Azolla in microwave oven compared to autoclave was statistically significant. Amounts of alcohol produced and its yields were 3.99 g/L and 33.13% for S. cerevisiae in 48 hours, 3.73 g/L and 30.45% for Pichia stipites in 48 hours, and 3.73 g/L and 30.45% for Z. californica in 24 hours after inoculation, respectively, with significant differences. Statistical comparison of results showed significant differences (P<0.05) in glucose production, at different conditions. Amounts of reducing sugars and glucose increased after optimization of levels of acid, time, and temperature. The overall optimum released sugar and glucose were obtained with 1.67% (w/v) acid using autoclave. Higher temperatures in microwave oven caused a significant increase (P<0.05) in furfural. Furfural severely inhibits fermentation. Hence, regarding the issues of energy consumption and time, amounts of inhibiting substances and sugar production, autoclave is found to be superior to the high temperature and pressure, generated in microwave oven, for hydrolyzing Azolla. Furthermore, given the amounts of Azolla in Anzali lagoon, it may be recommendable to use this plant as a biomass resource.

Real-time experimental demonstration of low-cost VCSEL intensity-modulated 11.25 Gb/s optical OFDM signal transmission over 25 km PON systems.

The feasibility of utilising low-cost, un-cooled vertical cavity surface-emitting lasers (VCSELs) as intensity modulators in real-time optical OFDM (OOFDM) transceivers is experimentally explored, for the first time, in terms of achievable signal bit rates, physical mechanisms limiting the transceiver performance and performance robustness. End-to-end real-time transmission of 11.25 Gb/s 64-QAM-encoded OOFDM signals over simple intensity modulation and direct detection, 25 km SSMF PON systems is experimentally demonstrated with a power penalty of 0.5 dB. The low extinction ratio of the VCSEL intensity-modulated OOFDM signal is identified to be the dominant factor determining the maximum obtainable transmission performance. Experimental investigations indicate that, in addition to the enhanced transceiver performance, adaptive power loading can also significantly improve the system performance robustness to variations in VCSEL operating conditions. As a direct result, the aforementioned capacity versus reach performance is still retained over a wide VCSEL bias (driving) current (voltage) range of 4.5 mA to 9 mA (275 mVpp to 320 mVpp). This work is of great value as it demonstrates the possibility of future mass production of cost-effective OOFDM transceivers for PON applications.

Imaging the femoral cortex: thickness, density and mass from clinical CT.

There is growing evidence that focal thinning of cortical bone in the proximal femur may predispose a hip to fracture. Detecting such defects in clinical CT is challenging, since cortices may be significantly thinner than the imaging system's point spread function. We recently proposed a model-fitting technique to measure sub-millimetre cortices, an ill-posed problem which was regularized by assuming a specific, fixed value for the cortical density. In this paper, we develop the work further by proposing and evaluating a more rigorous method for estimating the constant cortical density, and extend the paradigm to encompass the mapping of cortical mass (mineral mg/cm(2)) in addition to thickness. Density, thickness and mass estimates are evaluated on sixteen cadaveric femurs, with high resolution measurements from a micro-CT scanner providing the gold standard. The results demonstrate robust, accurate measurement of peak cortical density and cortical mass. Cortical thickness errors are confined to regions of thin cortex and are bounded by the extent to which the local density deviates from the peak, averaging 20% for 0.5mm cortex.

Imaging the femoral cortex: Thickness, density and mass from clinical CT

There is growing evidence that focal thinning of cortical bone in the proximal femur may predispose a hip to fracture. Detecting such defects in clinical CT is challenging, since cortices may be significantly thinner than the imaging system's point spread function. We recently proposed a model-fitting technique to measure sub-millimetre cortices, an ill-posed problem which was regularized by assuming a specific, fixed value for the cortical density. In this paper, we develop the work further by proposing and evaluating a more rigorous method for estimating the constant cortical density, and extend the paradigm to encompass the mapping of cortical mass (mineral mg/cm 2) in addition to thickness. Density, thickness and mass estimates are evaluated on sixteen cadaveric femurs, with high resolution measurements from a micro-CT scanner providing the gold standard. The results demonstrate robust, accurate measurement of peak cortical density and cortical mass. Cortical thickness errors are confined to regions of thin cortex and are bounded by the extent to which the local density deviates from the peak, averaging 20% for 0.5mm cortex. © 2012 Elsevier B.V.

On the percussion drilling of SI using a 20W MOPA based YB fiber laser

A study on the nanosecond fiber laser interaction with silicon was performed experimentally for the generation of percussion drilled holes. Single pulse ablation experiments were carried out on mono crystalline 650μm thick Si wafers. Changes of the mass removal mechanism were investigated by varying laser fluence up to 68 J/cm2 and pulse duration from 50 ns to 200 ns. Hole width and depth were measured and surface morphology were studied using scanning electron microscopy (SEM) and optical interferometric profilometry (Veeco NT3300). High speed photography was also used to examine laser generated plasma expansion rates. The material removal rate was found to be influenced by the pulse energy, full pulse duration and pulse peak power. Single pulse ablation depth of 4.42 μm was achieved using a 200 ns pulse of 13.3 J/cm 2, giving a maximum machining efficiency of 31.86 μm per mJ. Holes drilled with an increased fluence but fixed pulse length were deeper, exhibited low recast, but were less efficient than those produced at a lower fluence. The increased peak power in this case led to high levels of plasma and vapour production. The expansion of which, results in a strong driving recoil force, an increase in the rate and volume of melt ejection, and cleaner hole formation. The experimental findings show that for efficient drilling at a given energy, a longer, lower peak power pulse is more desirable than a high peak power short pulse.

Dynamic behaviour of gas jets in laser cutting

The efficiency and overall quality of a laser cutting operation is highly dependent on the assist gas parameters. The desire to cut thicker material has led to the observation of small process operating windows for thicker sections. The gas jet delivery and subsequent dynamical behaviour have significant effects on the cutting operation as the sample thickness increases. To date, few workers have examined the dynamical behaviour of the gas jet. This paper examines the characteristics of oxygen gas jets during CO2 laser cutting of steel. Particular emphasis is placed on the mass transfer effects that are operating within the kerf. Oxygen concentration levels within a model kerf are measured for various laser cutting set-ups. The results show a substantial reduction in oxygen concentration within the kerf. A system for oxygen concentration maintenance is described and cutting results from this system are compared with conventional techniques for cutting steels in the range 10 to 20mm thick. A theoretical analysis of turbulent mass transfer within a kerf is presented and compared with experiment.

Deformation and fracture of impulsively loaded sandwich panels

Light metal sandwich panel structures with cellular cores have attracted interest for multifunctional applications which exploit their high bend strength and impact energy absorption. This concept has been explored here using a model 6061-T6 aluminum alloy system fabricated by friction stir weld joining extruded sandwich panels with a triangular corrugated core. Micro-hardness and miniature tensile coupon testing revealed that friction stir welding reduced the strength and ductility in the welds and a narrow heat affected zone on either side of the weld by approximately 30%. Square, edge clamped sandwich panels and solid plates of equal mass per unit area were subjected to localized impulsive loading by the impact of explosively accelerated, water saturated, sand shells. The hydrodynamic load and impulse applied by the sand were gradually increased by reducing the stand-off distance between the test charge and panel surfaces. The sandwich panels suffered global bending and stretching, and localized core crushing. As the pressure applied by the sand increased, face sheet fracture by a combination of tensile stretching and shear-off occurred first at the two clamped edges of the panels that were parallel with the corrugation and weld direction. The plane of these fractures always lay within the heat affected zone of the longitudinal welds. For the most intensively loaded panels additional cracks occurred at the other clamped boundaries and in the center of the panel. To investigate the dynamic deformation and fracture processes, a particle-based method has been used to simulate the impulsive loading of the panels. This has been combined with a finite element analysis utilizing a modified Johnson-Cook constitutive relation and a Cockcroft-Latham fracture criterion that accounted for local variation in material properties. The fully coupled simulation approach enabled the relationships between the soil-explosive test charge design, panel geometry, spatially varying material properties and the panel's deformation and dynamic failure responses to be explored. This comprehensive study reveals the existence of a strong instability in the loading that results from changes in sand particle reflection during dynamic evolution of the panel's surface topology. Significant fluid-structure interaction effects are also discovered at the sample sides and corners due to changes of the sand reflection angle by the edge clamping system. © 2012 Elsevier Ltd. All rights reserved.

Multi-hit armour characterisation of metal-composite bi-layers

The ballistic performance of equi-mass plates made from (i) stainless steel (SS); (ii) carbon fibre/epoxy (CF) laminate and (iii) a hybrid plate of both materials has been characterised for a spherical steel projectile. The hybrid plate was orientated with steel on the impact face (SSCF) and on the distal face (CFSS). The penetration velocity (V 50) was highest for the SS plate and lowest for the CF plate. A series of double impact tests were performed, with an initial velocity V I and a subsequent velocity V II at the same impact site. An interaction diagram in (V I,V II) space was constructed to delineate penetration from survival under both impacts. The degree of interaction between the two impact events was greater for the CFSS plate than for the SSCF plate, implying that the distal face has the major effect upon the degree of interaction.