Insight of the interface of electroless Ni-P/SiC composite coating on aluminium alloy, LM24

Electroless nickel composite coatings with silicon carbide, SiC, as reinforcing particles deposited with Ni–P onto aluminium alloy, LM24, having zincating as under layer were subjected to heat treatment using air furnace. The changes at the interface were investigated using scanning electron microscope (SEM) and energy dispersive X-ray (EDX) to probe the chemistry changes upon heat treatment. Microhardness tester with various loads using both Knoop and Vickers indenters was used to study the load effect clubbed with the influence of second phase particles on the coating at the vicinity of the interface. It was observed that zinc was absent at the interface after elevated temperature heat treatment at 400–500 °C. Precipitation of copper and nickel with a distinct demarcation (copper rich belt) along the coating interface was seen with irregular thickness of the order of 1 μm. Migration of copper from the bulk aluminium alloy could have been the factor. Brittleness of the coating was confirmed on heat treatment when indented with Vickers. However, in composite coating the propagation of the microcrack was stopped by the embedded particles but the microcracks continue in the matrix when not interrupted by second phase particles (SiC).

Electroless nickel composite (Ni-P/SiC) coating - A study on interface and corrosion characteristic

Surface behaviour is of paramount importance as failure and degradation tend to initiate from the surface. Electroless composite coating (NiP/SiC) was developed using SiC as reinforcing particles. As heat treatment plays a vital role in electroless nickel coating owing to the changes in microstructure, phase structure and mechanical properties, an insight at the interface changes in chemistry and micromechanical behaviour was investigated using scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) and microindentation techniques. Corrosion performance was analysed using electrochemical impedance spectroscopy (EIS). Absence of zinc and migration of copper at the interface was detected. Brittleness and microcracks was seen long the interface when indenting at load of 500 gf (Vickers). Corrosion performance is weaker than particles free coating. However, a thin blanket of NiP could enhance the resistance to corrosive medium.

Hardware Software Interface: a Strategy for the implementation of Urban Agriculture

This paper describes how urban agriculture differs from conventional agriculture not only in the way it engages with the technologies of growing, but also in the choice of crop and the way these are brought to market. The authors propose a new model for understanding these new relationships, which is analogous to a systems view of information technology, namely Hardware-Software- Interface.
The first component of the system is hardware. This is the technological component of the agricultural system. Technology is often thought of as equipment, but its linguistic roots are in ‘technis’ which means ‘know how’. Urban agriculture has to engage new technologies, ones that deal with the scale of operation and its context which is different than rural agriculture. Often the scale is very small, and soils are polluted. There this technology in agriculture could be technical such as aquaponic systems, or could be soil-based agriculture such as allotments, window-boxes, or permaculture. The choice of method does not necessarily determine the crop produced or its efficiency. This is linked to the biotic that is added to the hardware, which is seen as the ‘software’.
The software of the system are the ecological parts of the system. These produce the crop which may or may not be determined by the technology used. For example, a hydroponic system could produce a range of crops, or even fish or edible flowers. Software choice can be driven by ideological preferences such as permaculture, where companion planting is used to reduce disease and pests, or by economic factors such as the local market at a particular time of the year. The monetary value of the ‘software’ is determined by the market. Obviously small, locally produced crops are unlikely to compete against intensive products produced globally, however the value locally might be measured in different ways, and might be sold on a different market. This leads to the final part of the analogy - interface.
The interface is the link between the system and the consumer. In traditional agriculture, there is a tenuous link between the producer of asparagus in Peru and the consumer in Europe. In fact very little of the money spent by the consumer ever reaches the grower. Most of the money is spent on refrigeration, transport and profit for agents and supermarket chains. Local or hyper-local agriculture needs to bypass or circumvent these systems, and be connected more directly to the consumer. This is the interface. In hyper-localised systems effectiveness is often more important than efficiency, and direct links between producer and consumer create new economies.

2D Monolayer MoS2–Carbon Interoverlapped Superstructure: Engineering Ideal Atomic Interface for Lithium Ion Storage: Engineering Ideal Atomic Interface for Lithium Ion Storage

A novel strategy for the controlled synthesis of 2D MoS<inf>2</inf>/C hybrid nanosheets consisting of the alternative layer-by-layer interoverlapped single-layer MoS<inf>2</inf> and mesoporous carbon (m-C) is demonstrated. Such special hybrid nanosheets with a maximized MoS<inf>2</inf>/m-C interface contact show very good performance for lithium-ion batteries in terms of high reversible capacity, excellent rate capability, and outstanding cycling stability.

High temperature thermal stability investigations of ammonium sulphide passivated InGaAs and interface formation with Al2O3 studied by synchrotron radiation based photoemission

High resolution synchrotron radiation core level photoemission measurements have been used to undertake a comparative study ofthe high temperature thermal stability ofthe ammonium sulphide passivated InGaAs surface and the same surface following the atomic layer deposition (ALD) of an ultrathin (∼1 nm) Al2O3 layer. The solution based ex situ sulphur passivation was found to be effective at removing a significant amount of the native oxides and protecting the surface against re-oxidation upon air exposure. The residual interfacial oxides which form between sulphur passivated InGaAs and the ultrathin Al2O3 layer can be substantially removed at high temperature (up to 700 ◦C) without impacting on the InGaAs stoichiometry while significant loss of indium was recorded at this temperature on the uncovered sulphur passivated InGaAs surface.

High temperature thermal stability of the HfO2/Ge (100) interface as a function of surface preparation studied by synchrotron radiation core level photo emission

High resolution soft x-ray photoemission spectroscopy (SXPS) have been used to study the high temperature thermal stability of ultra-thin atomic layer deposited (ALD) HfO2 layers (∼1 nm) on sulphur passivated and hydrofluoric acid (HF) treated germanium surfaces. The interfacial oxides which are detected for both surface preparations following HfO2 deposition can be effectively removed by annealing upto 700 °C without any evidence of chemical interaction at the HfO2/Ge interface. The estimated valence and conduction band offsets for the HfO2/Ge abrupt interface indicated that effective barriers exist to inhibit carrier injection.

The Restorability Assessment and Endodontic Access Cavity Interface

Successful root canal treatment requires management of the bacterial infection within the root canal space and protection of residual tooth structure with direct/indirect restorations. Long-term success depends upon prevention of re-infection of the root canal space as well as ensuring favorable distribution of the occlusal forces throughout the residual tooth structure. Appropriate planning and design of the final restoration prior to initiating root canal treatment is paramount in achieving this objective. This article describes simultaneous restorability assessment and access cavity preparation to optimize outcome of both endodontic and prosthodontic treatment of the endodontically involved tooth.

Growing Up On an Interface: Findings and Implications for the Social Needs, Mental Health and Lifetime Opportunities of Belfast Youth

In this research we aimed to find out what types of risk (if any) affected young people and children growing up in places of high religious segregation or what we normally call interface communities. This is important as we know that risk and experiences of harm and violence can have negative impacts upon development, emotional well-being and future prospects. It is important to understand what types of risk affect young people and children so as we can respond to these in terms of aiding better personal and community development with regard to health, work, education and wider opportunities.

Learning about probability from text and tables: Do color coding and labeling through an interactive-user interface help?

Learning from visual representations is enhanced when learners appropriately integrate corresponding visual and verbal information. This study examined the effects of two methods of promoting integration, color coding and labeling, on learning about probabilistic reasoning from a table and text. Undergraduate students (N = 98) were randomly assigned to learn about probabilistic reasoning from one of 4 computer-based lessons generated from a 2 (color coding/no color coding) by 2 (labeling/no labeling) between-subjects design. Learners added the labels or color coding at their own pace by clicking buttons in a computer-based lesson. Participants' eye movements were recorded while viewing the lesson. Labeling was beneficial for learning, but color coding was not. In addition, labeling, but not color coding, increased attention to important information in the table and time with the lesson. Both labeling and color coding increased looks between the text and corresponding information in the table. The findings provide support for the multimedia principle, and they suggest that providing labeling enhances learning about probabilistic reasoning from text and tables

A interface carboneto de silício-solução aquosa e o enchimento por barbotina

Neste trabalho estudaram-se as interfaces carboneto de silício-solução aquosa e carbono-solução aquosa, com vista a uma melhor compreensão dos processos de floculaçáo e desfloculaçáo de suspensões de cada um daqueles materiais e de suas misturas. Os pós foram caracterizados por recurso a técnicas de sedimentação, microscopia electrónica de varrimento, difracçáo de raios-X, análises térmicas, espectroscopia de infra-vermelhos e picnometria de hélio. As suspensões foram caracterizadas por técnicas de microelectroforese, sedimentação e reologia. Estudou-se a influência de algumas variáveis mais importantes do processo de enchimento por barbotina como, por exemplo, o mecanismo e o grau de estabilização das suspensões, a concentração de sólidos, a distribuição granulométrica das partículas, e o tempo de envelhecimento das suspensões, na estrutura das partículas em suspensão e nas características dos corpos conformados por enchimento por barbotina. A cinética deste processo foi estudada sob o efeito de pressão aplicada e relacionada com a estrutura das partículas em suspensão e com a microstrutura dos corpos em verde. Estudaram-se os mecanismos da segregação de tamanhos de partículas em suspensão que ocorre durante o processo de enchimento por barbotina devidos aos efeitos da gravidade e da obstrução do bolo pelas partículas finas. Discutiram-se os domínios das variáveis do processo em que cada um daqueles efeitos é dominante e propôs-se um novo modelo para o fenómeno da segregação por efeito de obstrução capaz de interpretar os resultados observados neste trabalho e os encontrados na literatura. Estabeleceram-se correlações estreitas entre as variáveis do processo de enchimento por barbotina, a microestrutura dos corpos conformados e o seu comportamento durante a etapa da secagem. Procurou ainda avaliar-se a capacidade do enchimento por barbotina para preparar materiais compósitos de carboneto de silício e carbono com características adequadas para a sinterizaçáo reactiva.

Perception-based painterly rendering: funcionality and interface design

Painterly rendering (non-photorealistic rendering or NPR) aims at translating photographs into paintings with discrete brush strokes, simulating certain techniques (im- or expressionism) and media (oil or watercolour). Recently, our research into visual perception and models of processes in the visual cortex resulted in a new rendering scheme, in which detected lines and edges at different scales are translated into brush strokes of different sizes. In order to prepare a version which is suitable for many users, including children, the design of the interface in terms of window and menu system is very important. Discussions with artists and non-artists led to three design criteria: (1) the interface must reflect the procedures and possibilities that real painters follow and use, (2) it must be based on only one window, and (3) the menu system must be very simple, avoiding a jungle of menus and sub-menus. This paper explains the interface that has been developed.

Mlearning : ambiente de aprendizagem com interface adaptativo

Trabalho de projeto de mestrado, Educação (Tecnologias de Informação e Comunicação e Educação), Universidade de Lisboa, Instituto de Educação, 2013