Leaving final-cut grass silage in situ overwinter as a seed resource for declining farmland birds

The loss of seed-rich wintering habitats has been a major contributory cause of farmland bird population declines in western Europe. Agricultural grasslands are particularly poor winter foraging habitats for granivorous birds, which have declined most in the pastoral farming regions of western Britain. We describe an experiment to test the utility of fertile ryegrass (Lolium) swards as a potentially rich source of winter seed for declining farmland birds. Four patches of final-cut grass silage were allowed to set seed and were left in situ overwinter. Half of each patch was lightly aftermath grazed in an attempt to increase the accessibility of the seed to foraging birds and reduce the perceived predation risk. Large numbers of yellowhammers (Emberiza citrinella) and reed buntings (E. schoeniclus) foraged on the seeded plots throughout the winter. They preferred to forage on ungrazed seeded plots, where the accumulation of senescent foliage resulted in a 14% average loss in silage yield in the following season. However, seed produced on the plots also led to sward regeneration, increasing subsequent yields on some plots. The technique offers clear benefits as a potential future agri-environment measure for declining granivorous birds, with wide applicability, but requires further development to minimise sward damage and costs to the farmer. Autumn grazing should reduce sward damage, but at the cost of reduced usage by buntings. Using the technique just prior to reseeding would be one way of avoiding any costs of sward damage.

In situ degradability of dry matter and neutral-detergent fibre of thorn scrubland forage consumed by goats in the semi-arid region of north Mexico

Three goats provided with oesophageal and ruminal cannulae were used to determine variations in dry matter (DM) and neutral-detergent fibre (NDF) degradability of the forage consumed when grazing thorn scrubland in the semi-arid region of north Mexico, during two consecutive dry and wet periods. Ingesta samples were incubated intraruminally, the data were fitted to the exponential equation P = a + b (1-e(-ct)) and statistically analysed using a randomized-block design. Organic matter and crude protein (CP) contents were higher (P < 0.05) in the wet seasons. Values of NDF were similar in dry and wet season of both years whereas higher numerical values of acid-detergent fibre (ADF), lignin and cellulose were registered in the dry seasons. DM and NDF degradabilities after 24 and 48 h of ruminal incubation were higher (P < 0.05) in the wet seasons. Higher values (P < 0.05) in DM and NDF bag losses at zero time (A fraction) were registered in the two wet seasons. The insoluble but fermentable DM and NDF (B fractions) were higher (P < 0.05) in the 1999 wet season and variable in the rest of the studied period. Numerically higher values of DM and NDF c fraction were found in wet periods, whereas DM and NDF potential degradabilities were higher (P < 0.05) in the wet season in 1999 and similar across seasons in 2000. Lowest (P < 0.05) contents of CP in grazed forage, DM and NDF degradabilities after 48 h of ruminal incubation, and A, and B, and c fractions were observed in the dry seasons. Thus, these results may be related to both the lower feeding value of forage consumed by the animals and lower performance of livestock during this period. Then, the DM and NDF degradability after 48 h, together with the insoluble but fermentable matter and the c fraction permit the nutritive value of the forage consumed by grazing goats to be accurately described.

Challenges of in situ conservation of crop wild relatives

Crop wild relatives (CWRs) will gain in importance as changing climates put both traditional and advanced cultivars under increasing stress, leading to a need for plant breeding to produce new varieties able to grow under the new climate regimes. Traditionally, the approach to the conservation of CWRs has been ex situ - the collection and maintenance of seed accessions in national, regional, and international germplasm banks, supplemented by field genebanks for species with recalcitrant seeds. More recently the need to maintain CWRs in their natural habitats (in situ) has been advocated. This is very different from on-farm conservation of traditional land races and is a complex multidisciplinary process. Particular problems that have to be addressed include the adoption of a workable definition of what is a CWR, application of priority-determining mechanisms because of the large number of candidate species of CWRs, assessment of the effectiveness of conservation approaches, the relative costs of in situ and ex situ approaches, integration of CWR in situ conservation into national programmes, and the challenges posed by global change. CWRs may be conserved in both protected and non-protected areas. Presence in the former is no guarantee of their survival and in most cases some degree of management intervention is required. Experience derived from recent EU- and GEF-funded CWR conservation initiatives will be drawn upon.

Expression of metallothionein genes I and II in bank vole clethrionomys glareolus populations chronically exposed in situ to heavy metals

The expression of two metallothionein genes (Mt-I and Mt-II) in the liver, kidney, and gonad of bank voles collected at four metal-contaminated sites (Cd, Zn, Pb, and Fe) were measured using the quantitative real-time PCR method (QPCR). Relative Mt gene expression was calculated by applying a normalization factor (NF) using the expression of two housekeeping genes, ribosomal 18S and beta-actin. Relative Mt expression in tissues of animals from contaminated sites was up to 54.8-fold higher than those from the reference site for Mt-I and up to 91.6-fold higher for Mt-II. Mt-II gene expression in the livers of bank voles from contaminated sites was higher than Mt-I gene expression. Inversely, Mt-II expression in the kidneys of voles was lower than Mt-I expression. Positive correlations between cadmium levels in the tissues and Mt-I were obtained in all studied tissues. Zinc, which undergoes homeostatic regulation, correlated positively with both Mt-I and Mt-II gene expression only in the kidney. Results showed that animals living in chronically contaminated environments intensively activate detoxifying mechanisms such as metallothionein expression. This is the first time that QPCR techniques to measure MT gene expression have been applied to assess the impact of environmental metal pollution on field collected bank voles.

The chromosomal assessment of salt tolerant substituted tritipyrum using genomic fluorescent in situ hybridiization (FISH)

Wheat, although moderately tolerant to salt, can not be cultivated in many areas. However, in the triticeae tribe, some of the wild wheat relatives are highly tolerant, e.g. Thinopyrum bessarabicum, which grows on the sea shore. Eight primary hexaploid tritipyrum lines, amphiploids between Triticum durum and Thinopyrum bessarabicum have been produced which can set seed in at least 250 mM NaCl. These tritipyrums (2n=6x=42, AABBEbEb) due to reasons such as brittle rachis, continuous production of tillers, late maturity, tall stature and meiotic instability will not fulfill the requirements of a successful commercial salt tolerant crop. To overcome such problems the substituted tritipyrum, in which selected Eb chromosomes are replaced by D genome chromosomes of 6x wheat, was produced from 6x tritipyrum x 6x wheat hybrids (F1: 2n=6x=42, AABBDEb) followed by selfing and backcrossing with 6x tritipyrum. The fertile plants among the above progenies were screened by the genomic fluorescent in situ hybridization technique to identify their Eb and D chromosome constitution. This study showed that producing tritiprum with variable numbers of Eb and D genome chromosomes is feasible and that FISH is a useful technique for determining the number of Eb chromosomes present.

Incorporation of in situ and biomarker assays in higher-tier assessment of the aquatic toxicity of insecticides

This study was designed to test the feasibility of integrating in situ, single species exposures and biomarker analysis into microcosm studies. Experimental ponds were dosed with pirimiphos methyl (PM) and lindane. C. riparius fourth instar larvae were deployed for 48 h on nine separate occasions during the study period before and after treatment. Surviving larvae were analysed for acetylcholinesterase activity (AChE). Survival and biomarker data were compared to chironomid assemblage analysis by monitoring insects emerging from the microcosms. Survival of chironomids within the in situ systems commenced on day + 16 after treatment with 31.6% and 53.3% survival in the lindane and PM treated ponds, respectively. In contrast, the first emergence from the microcosms occurred on days + 27, in respect to lindane, and + 59 for the PM treated ponds. Thus the in situ bioassay was able to demonstrate gradual reduction in toxicity within the sediment before this was evident from macroinvertebrate monitoring. Significant ACNE inhibition was only detected on exposure to PM. Levels decreased from 75% on day + 16 to 26% by day +29. The biomarker analysis confirmed that, by the end of the study, the insecticide was no longer exerting an effect. We discuss how the use of in situ bioassays could also aid comparison of microcosm studies by adding a standardized dimension. (C) 2003 Elsevier Ltd. All rights reserved.

Complete filling of zeolite frameworks with polyalkynes formed in situ by transition-metal ion catalysts

We report the use of transition-metal-exchanged zeolites as media for the catalytic formation and encapsulation of both polyethyne and polypropyne, and computer modeling studies on the composites so formed. Alkyne gas was absorbed into the pores of zeolite Y (Faujasite) exchanged with transition-metal cations [Fe(II), Co(II), Cu(II), Ni(II), and Zn(II)]. Ni(II) and Zn(II) were found to be the most efficient for the production of poly-ynes. These cations were also found to be effective in polymer generation when exchanged in zeolites mordenite and beta. The resulting powdered samples were characterized by FTIR, Raman, diffuse reflectance electronic spectroscopy, TEM, and elemental analysis, revealing, nearly complete loading of the zeolite channels for the majority of the samples. Based on the experimental carbon content, we have derived the percentage of channel filling, and the proportion of the channels containing a single polymer chain for mordenite. Experimentally, the channels for Y are close to complete filling for polyethyne (PE) and polypropyne (PP), and this is also true for polyethyne in mordenite. Computer modeling studies using Cerius2 show that the channels of mordenite can only accept a single polymer chain of PP, in which case these channels are also completely filled.

An in situ time-dependent study of the photodimerisation of chloro-derivatives of trans-cinnamic acid using infrared microspectroscopy with a synchrotron radiation source

The photodimerisation of single crystals of substituted cinnamic acid has been monitored continuously by infrared microscopy using a synchrotron source. The beta-form of 2,4-dichloro-trans-cinnamic acid dimerises under ultraviolet irradiation to form the corresponding beta-truxinic acid derivative in a reaction which follows strictly first order kinetics. By contrast the corresponding reactions in single crystals of beta-2-chloro-trans-cinnamic acid and beta-4-chloro-trans-cinnamic acid deviate somewhat from first order kinetics as a result of solid-state effects. In all three cases the reactions proceed smoothly from monomer to dimer with no hint of any reaction intermediate.

In situ observation of lithium hydride hydrolysis by DRIFT spectroscopy

Polycrystalline LiH was studied in situ using diffuse reflectance infrared Fourier transform (DRIFT) spectroscopy to investigate the effect water vapour has on the rate of production of the corrosion products, particularly LiOH. The reaction rate of the formation of surface LiOH was monitored by measurement of the hydroxyl (OH) band at 3676 cm(-1). The initial hydrolysis rate of LiH exposed to water vapour at 50% relative humidity was found to be almost two times faster than LiH exposed to water vapour at 2% relative humidity. The hydrolysis rate was shown to be initially very rapid followed by a much slower, almost linear rate. The change in hydrolysis rate was attributed to the formation of a coherent layer of LiOH on the LiH surface. Exposure to lower levels of water vapour appeared to result in the formation of a more coherent corrosion product, resulting in effective passivation of the surface to further attack from water. Crown Copyright (c) 2007 Published by Elsevier B.V. All rights reserved.

Microfabrication of high-performance aromatic polymers as nanotubes or fibrils by in situ ring-opening polymerisation of macrocyclic precursors

Melt-phase nucleophilic ring-opening polymerisation of macrocyclic aromatic ethers and thioethers at high temperatures within the cylindrical pores of an anodic-alumina membrane, followed by dissolution of the template, enables replication of the membrane's internal pore structure and so affords high-performance aromatic polymers with well-defined fibrillar or tubular morphologies.

In situ formation of gold nanoparticles with a thermoresponsive block copolymer corona

Gold nanoparticles with a polymer coating exhibiting large and reversible thermoresponsiveness are prepared via a one-pot synthesis method using narrow polydispersity thermoresponsive block copolymers. (C) 2007 Elsevier B.V. All rights reserved.

Thermal Fractionation and isothermal crystallization of polyethylene nanocomposites prepared by in situ polymerization

Nanocomposites of high-density polyethylene (HDPE) and carbon nanotubes (CNT) of different geometries (single wall, double wall, and multiwall; SWNT, DWNT, and MWNT) were prepared by in situ polymerization of ethylene on CNT whose surface had been previously treated with a metallocene catalytic system. In this work, we have studied the effects of applying the successive self-nucleation and annealing thermal fractionation technique (SSA) to the nanocomposites and have also determined the influence of composition and type of CNT on the isothermal crystallization behavior of the HDPE. SSA results indicate that all types of CNT induce the formation of a population of thicker lamellar crystals that melt at higher temperatures as compared to the crystals formed in neat HDPE prepared under the same catalytic and polymerization conditions and subjected to the same SSA treatment. Furthermore, the peculiar morphology induced by the CNT on the HDPE matrix allows the resolution of thermal fractionation to be much better. The isothermal crystallization results indicated that the strong nucleation effect caused by CNT reduced the supercooling needed for crystallization. The interaction between the HDPE chains and the surface of the CNT is probably very strong as judged by the results obtained, even though it is only physical in nature. When the total crystallinity achieved during isothermal crystallization is considered as a function of CNT content, it was found that a competition between nucleation and topological confinement could account for the results. At low CNT content the crystallinity increases (because of the nucleating effect of CNT on HDPE), however, at higher CNT content there is a dramatic reduction in crystallinity reflecting the increased confinement experienced by the HDPE chains at the interfaces which are extremely large in these nanocomposites. Another consequence of these strong interactions is the remarkable decrease in Avrami index as CNT content increases. When the Avrami index reduces to I or lower, nucleation dominates the overall kinetics as a consequence of confinement effects. Wide-angle X-ray experiments were performed at a high-energy synchrotron source and demonstrated that no change in the orthorhombic unit cell of HDPE occurred during crystallization with or without CNT.

Micelle-hosted bimetallic Pd-Ru nanoparticle for in situ catalytic hydrogenation in supercritical CO2

Bimetallic Pd-Ru nanoparticles of different elemental ratios are prepared via in situ reduction of their simple salts in reverse micelles in supercritical carbon dioxide (scCO(2)). The optimised Pd:Ru (1: 1) nanoparticle shows the highest activity for hydrogenation of functionalised alkene under mild conditions, which can be easily recycled under the reaction conditions without use of organic solvent. (c) 2006 Elsevier B.V. All rights reserved.

Molecular characterisation of the gut microflora of healthy and inflammatory bowel disease cats using fluorescence in situ hybridisation with special reference to Desulfovibrio spp

Inflammatory bowel disease (IBD) is a common cause of chronic large bowel diarrhoea in cats. Although the aetiology of IBD is unknown, an immune-mediated response to a luminal antigen is thought to be involved. As knowledge concerning the colonic microflora of cats is limited and requires further investigation, the purpose of this study was to determine the presence of specific bacterial groups in normal and IBD cats, and the potential role they play in the health of the host. Total bacterial populations, Bacteroides spp., Bifidobacterium spp., Clostridium histolyticum subgp., Lactobacillus-Enterococcus subgp. and Desulfovibrio spp. were enumerated in 34 healthy cats and 11 IBD cats using fluorescence in situ hybridisation. The study is one of the first to show the presence of Desulfovibrio in cats. Total bacteria, Bifidobacterium spp. and Bacteroides spp. counts were all significantly higher in healthy cats when compared with IBD cats, whereas Desulfovibrio spp. (producers of toxic sulphides) numbers were found to be significantly higher in colitic cats. The information obtained from this study suggests that modulation of bacterial flora by increasing bifidobacteria and decreasing Desulfovibrio spp. may be beneficial to cats with IBD. Dietary intervention may be an important aspect of their treatment.

A method for estimating the turbulent kinetic energy dissipation rate from a vertically pointing Doppler lidar, and independent evaluation from balloon-borne in situ measurements

A method of estimating dissipation rates from a vertically pointing Doppler lidar with high temporal and spatial resolution has been evaluated by comparison with independent measurements derived from a balloon-borne sonic anemometer. This method utilizes the variance of the mean Doppler velocity from a number of sequential samples and requires an estimate of the horizontal wind speed. The noise contribution to the variance can be estimated from the observed signal-to-noise ratio and removed where appropriate. The relative size of the noise variance to the observed variance provides a measure of the confidence in the retrieval. Comparison with in situ dissipation rates derived from the balloon-borne sonic anemometer reveal that this particular Doppler lidar is capable of retrieving dissipation rates over a range of at least three orders of magnitude. This method is most suitable for retrieval of dissipation rates within the convective well-mixed boundary layer where the scales of motion that the Doppler lidar probes remain well within the inertial subrange. Caution must be applied when estimating dissipation rates in more quiescent conditions. For the particular Doppler lidar described here, the selection of suitably short integration times will permit this method to be applicable in such situations but at the expense of accuracy in the Doppler velocity estimates. The two case studies presented here suggest that, with profiles every 4 s, reliable estimates of ϵ can be derived to within at least an order of magnitude throughout almost all of the lowest 2 km and, in the convective boundary layer, to within 50%. Increasing the integration time for individual profiles to 30 s can improve the accuracy substantially but potentially confines retrievals to within the convective boundary layer. Therefore, optimization of certain instrument parameters may be required for specific implementations.