Water reduction in waste-activated sludge by resettling and filtration in batch. Phase (1): pilot-scale experiments to optimize performance

This article describes an effective procedure for reducing the water content of excess sludge production from a wastewater treatment plant by increasing its concentration and, as a consequence, minimizing the volume of sludge to be managed. It consists of a pre-dewatering sludge process, which is used as a preliminary step or alternative to the thickening. It is made up of two discontinuous sequential stages: the first is resettling and the second, filtration through a porous medium. The process is strictly physical, without any chemical additives or electromechanical equipment intervening. The experiment was carried out in a pilot-scale system, consisting of a column of sedimentation that incorporates a filter medium. Different sludge heights were tested over the filter to verify the influence of hydrostatic pressure on the various final concentrations of each stage. The results show that the initial sludge concentration may increase by more than 570% by the end of the process with the final volume of sludge being reduced in similar proportions and hydrostatic pressure having a limited effect on this final concentration. Moreover, the value of the hydrostatic pressure at which critical specific cake resistance is reached is established.

Emissions of Gases, Polycyclic Aromatic Hydrocarbons and Brominated Pollutants during Thermal Degradation of Waste Printed Circuit Boards

Resumen del póster presentado en Symposium on Renewable Energy and Products from Biomass and Waste, CIUDEN (Cubillos de Sil, León, Spain), 12-13 May 2015

The combined effect of plastics and food waste accelerates the thermal decomposition of refuse-derived fuels and fuel blends

Mechanical treatments such as shredding or extrusion are applied to municipal solid wastes (MSW) to produce refuse-derived fuels (RDF). In this way, a waste fraction (mainly composed by food waste) is removed and the quality of the fuel is improved. In this research, simultaneous thermal analysis (STA) was used to investigate how different mechanical treatments applied to MSW influence the composition and combustion behaviour of fuel blends produced by combining MSW or RDF with wood in different ratios. Shredding and screening resulted in a more efficient mechanical treatment than extrusion to reduce the chlorine content in a fuel, which would improve its quality. This study revealed that when plastics and food waste are combined in the fuel matrix, the thermal decomposition of the fuels are accelerated. The combination of MSW or RDF and woody materials in a fuel blend has a positive impact on its decomposition.

Synthesis of denim waste-based adsorbents and their application in water defluoridation

This study evaluates the application of denim fiber scraps as a precursor for the synthesis of adsorbents for water treatment via pyrolysis and their application in water defluoridation. The best pyrolysis conditions for the synthesis of this novel adsorbent have been identified and a metal doping route with different salts of Al3 +, La3 + and Fe3 + was proposed to improve its fluoride adsorption behavior. Different spectroscopic and microscopic techniques (i.e., FTIR, XPS, XRF, SEM) were used to characterize the precursor and adsorbents, and to analyze the surface interactions involved in the fluoride removal mechanism. Experimental results showed that these adsorbents were effective for fluoride adsorption showing uptakes up to 4.25 mg/g. The Si-O–metal–F interactions appear to be highly relevant for the fluoride removal. This study highlights the potential of denim textile waste as a raw material for the production of added-value products, thus minimizing their associated disposal cost. It also shows the performance of denim textile waste as a precursor of adsorbents for addressing relevant environmental concerns such as fluoride pollution.

Marine debris occurrence and treatment: A review

Marine debris produces a wide variety of negative environmental, economic, safety, health and cultural impacts. Most marine litter has a very low decomposition rate (as plastics, which are the most abundant type of marine debris), leading to a gradual, but significant accumulation in the coastal and marine environment. Along that time, marine debris is a significant source of chemical contaminants to the marine environment. Once extracted from the water, incineration is the method most widely used to treat marine debris. Other treatment methods have been tested, but they still need some improvement and so far have only been used in some countries. Several extraction and collection programs have been carried out. However, as marine debris keep entering the sea, these programs result insufficient and the problem of marine debris will continue its increase. The present work addresses the environmental impact and social aspects of the marine debris, with a review of the state of the art in the treatments of this kind of waste, together with an estimation of the worldwide occurrence and characteristics.

Management of small waste flows /

Mode of access: Internet.

Fate of priority pollutants in publicly owned treatment works : pilot study /

Mode of access: Internet.

Laboratory investigation of residual liquid organics from spills, leaks, and the disposal of hazardous wastes in groundwater /

Mode of access: Internet.

Treatment of petroleum refinery, petrochemical, and combined industrial-municipal wastewaters with activated carbon : literature review /

Mode of access: Internet.

Beneficial disposal of water purification plant sludges in wastewater treatment /

Mode of access: Internet.

A comparison of oxidation ditch plants to competing processes for secondary and advanced treatment of municipal wastes /

Mode of access: Internet.

Treatment of wastewaters from adhesives and sealants manufacture by ultrafiltration /

Mode of access: Internet.

Evaluation of physical chemical treatment at Rosemount /

Mode of access: Internet.

Survey of solidification/stabilization technology for hazardous industrial wastes /

Mode of access: Internet.

Processing chrome tannery effluent to meet best available treatment standards /

Mode of access: Internet.