PP／间同1,2-聚丁二烯的物理力学性能

添加不同质量分数的间同1,2-聚丁二烯(sPB)热塑性弹性体对聚丙烯(PP)共混改性,研究了共混体系的物理力学性能。PP与sPB结构相似,有良好的相容性,随着w(sPB)从0增至40%,共混体系的屈服拉伸强度、弯曲模量及耐热性有所降低;悬臂梁冲击强度增加,且常温悬臂梁冲击强度增幅较大,但低温悬臂梁冲击强度增加较少;断裂伸长率和熔体流动速率先增加后减少。

Guanidine/Pd(OAc)(2)-catalyzed room temperature Suzuki cross-coupling reaction in aqueous media under aerobic conditions

A highly efficient Pd(OAc)(2)/guanidine aqueous system for the room temperature Suzuki cross-coupling reaction has been developed. The new water-soluble and air-stable catalyst Pd(OAc)(2)(.)(1f)(2) from Pd(OAc)(2) and 1,1,3,3-tetramethyl-2-n-butylguanidine (1f) was synthesized and characterized by X-ray crystallography. In the presence of Pd(OAc)(2)(.)(1f)(2), coupling of arylboronic acids with a wide range of aryl halides, including aryl iodides, aryl bromides, even activated aryl chlorides, was carried out smoothly in aqueous solvent to afford the cross-coupling products in good to excellent yields and high turnover numbers (TONs) (TONs up to 850 000 for the reaction of 1-iodo-4-nitrobenzene and phenylboronic acid). Furthermore, this mild protocol could tolerate a broad range of functional groups.

Alternating copolymerization of carbon dioxide and propylene oxide catalyzed by (R,R)-SalenCo(III)-(2,4-dinitrophenoxy) and Lewis-basic cocatalyst

A binary catalyst system of a chiral (R,R)-SalenCo(III)(2,4-dinitrophenoxy) (salen = N,N-bis(3,5-di-tert-butylsalicylidene)-1,2-diphenylethylenediimine) in conjunction with (4-dimethylamino)pyridine (DMAP) was developed to generate the copolymerization of carbon dioxide (CO2) and racemic propylene oxide (rac-PO). The influence of the molar ratio of catalyst components, the operating temperature, and reaction pressure on the yield as well as the molecular weight of polycarbonate were systematically investigated. High yield of turnover frequency (TOF) 501.2 h(-1) and high molecular weight of 70,400 were achieved at an appropriate combination of all variables. The structures of as-prepared products were characterized by the IR, H-1 NMR, C-13 NMR measurements. The linear carbonate linkage, highly regionselectivity and almost 100% carbonate content of the resulting polycarbonate were obtained with the help of these effective catalyst systems under facile conditions.

Polyelectrolyte-functionalized ionic liquid for electrochemistry in supporting electrolyte-free aqueous solutions and application in amperometric flow injection analysis

As a green process, electrochemistry in aqueous solution without a supporting electrolyte has been described based on a simple polyelectrolyte-functionalized ionic liquid (PFIL)-modified electrode. The studied PFIL material combines features of ionic liquids and traditional polyelectrolytes. The ionic liquid part provides a high ionic conductivity and affinity to many different compounds. The polyelectrolyte part has a good stability in aqueous solution and a capability of being immobilized on different substrates. The electrochemical properties of such a PFIL-modified electrode assembly in a supporting electrolyte-free solution have been investigated by using an electrically neutral electroactive species, hydroquinone ( HQ) as the model compound. The partition coefficient and diffusion coefficient of HQ in the PFIL film were calculated to be 0.346 and 4.74 X 10(-6) cm(2) s(-1), respectively. Electrochemistry in PFIL is similar to electrochemistry in a solution of traditional supporting electrolytes, except that the electrochemical reaction takes place in a thin film on the surface of the electrode. PFILs are easily immobilized on solid substrates, are inexpensive and electrochemically stable. A PFIL-modified electrode assembly is successfully used in the flow analysis of HQ by amperometric detection in solution without a supporting electrolyte.

Hydrothermal synthesis, structure characterization of a new mixed Mo/V metal-oxygen cluster compound: [Co(phen)(3)](2)[HPMo4V (Mo4V6IV)-V-VI M2O44]center dot 4H(2)O, (M=0.78Mo(V)+0.22V(IV))

A new polyoxometalate [Co(phen)(3)](2)[HPMo4V Mo-4(VI) V-6(IV) M2O44]center dot 4H(2)O (M = 0.78Mo(V)+ 0.22V(IV)) 1 was hydrothermally synthesized and characterized by IR, elemental analyses, X-ray photoelectron spectrum, ESR and single crystal X-ray diffraction. The title compound is in the triclinic space group P (1) over bar with a = 12.0953(7) angstrom, b = 14.0182(6) angstrom, c = 14.6468(7) angstrom, V=2402.55(18) angstrom(3), alpha = 105.134(2), beta = 91.841(3), gamma = 91.401(2), Z = 1, and R-1 (wR(2)) = 0.0617 (0.1701). The compound was prepared from tetra-capped pseudo-Kepin with phosphorus-centered polyoxoanions [PMo8V6M2O44](5-) , [Co(phen)(3)](2+) cations and linked through hydrogen bonds and pi-pi stacking interaction into three-dimensional supramolecular framework. Astudy of the magnetic properties of 1 demonstrates that it exhibits antiferromagnetic coupling interactions.

Facilitated ion-transfer of sodium cation by (anthraquinone-1-yloxy) methane-15-crown-5 across the water/1,2-dichloroethane microinterface

The transfer of sodium cation facilitated by (anthraquinone-1-yloxy) methane-15-crown-5(L) has been investigated at the water/1,2-dichloroethane microinterface supported at the tip of a micropipette. The diffusion coefficient of (anthraquinone-1-yloxy) methane-15-crown-5 obtained was (3.42 +/- 0.20) x 10(-6) cm(2) s(-1). The steady-state voltammograms were observed for forward and backward scans due to sodium ion transfer facilitated by L with 1:1 stoichiometry. The mechanism corresponded to an interfacial complexation (TIC) and interfacial dissociation (TID) process. The association constant was calculated to be log beta(o) = 11.08 +/- 0.03 in the DCE phase. The association constant of other alkali metals (Li+, K+, Rb+) were also obtained.

成核剂1,3:2,4-二(亚苄基)-D山梨醇对PET/PEN共混体系结构和结晶形态影响

利用差示扫描量热仪、X射线衍射仪、正交偏光显微镜研究了成核剂 1,3 :2 ,4-二 (亚苄基 ) -D山梨醇(DBS)对聚对苯二甲酸乙二醇酯 (PET) /聚 2 ,6-萘二甲酸乙二醇酯 (PEN)共混体系的结构及结晶形态的影响。结果表明 :成核剂的加入 ,使PET/PEN共混体系熔融起始温度升高 10℃左右 ,结晶峰形变尖锐 ,说明加入成核剂后有效促进了PET/PEN共混体系的结晶。实验结果表明 :成核剂含量低于 1%时 ,PET/PEN共混体系晶体的球晶完整。成核剂含量大于 3 %时 ,PET/PEN /DBS共混体系晶体的球晶碎小。成核剂的加入 ,能够有效地减小球晶尺寸和降低球晶的完善性

Syntheses and crystal structures of [Mn(H2O)(4)(bpy)]L center dot 4H(2)O, [Mn(H2O)(4)(bpy)]L ' center dot 4H(2)O (H2L = SUCCINIC ACID, H2L ' = FUMARIC ACID)

Reactions of freshly prepared M(OH)(2-2x)(CO3)(x) (.) yH(2)O (M = Mn, Zn) and 4,4'-bipyridine (bpy) with succinic acid (H2L) or famaric acid (H2L') in CH3OH-H2O afforded [Mn(H2O)(4)(bpy)]L (.) 4H(2)O, 1, [Mn(H2O)(4)(bpy)]L' (.) 4H(2)O, 2 and [Zn(H2O)(4)(bpy)]L (.) 4H(2)O, 3. The three coordination polymers are isostructural and consist of (1)(infinity)[M(H2O)(4)(bpy)(2/2)](2+) cationic chains, crystal H2O molecules and dicarboxylate anions (succinate or fumarate anions). Within the chains, the metal atoms are each octahedrally coordinated by four aqua oxygen atoms and two pyridyl nitrogen atoms from two 4,4'-bipyridine ligands. The crystal H2O molecules are hydrogen bonded to dicarboxylate anions to form ribbon-like anionic chains. The cationic and anionic chains are interconnected via hyqrogen bonds to generate a 3D network. Crystal data: 1 triclinic, P (1) over bar, a = 7.235(1), b = 7.749(2), c = 10.020(2) Angstrom, alpha = 79.95(3), beta = 88.79(3), gamma = 71.39(3)degrees, V = 523.9(2) Angstrom(3) and D-cal = 1.494 g cm(-3) for Z = 1; 2 triclinic, P (1) over bar, a = 7.127(1), b = 7.800(2), c = 9.945(2) Angstrom, alpha = 80.26(3), beta = 87.86(3), gamma = 72.69(3)degrees, V = 520.2(2) Angstrom(3) and D-cal = 1.498 g cm(-3) for Z = 1; 3 triclinic, P (1) over bar, a = 7.189(1), b = 7.764(2), c = 9.843(2) Angstrom, alpha = 79.16(3), beta = 87.80(3), gamma = 71.29(3)degrees, V = 510.9(2) Angstrom(3) and D-cal = 1.559 g cm(-3) for Z = 1.

Self-immobilized metallocene catalysts bearing an allyl group for ethylene polymerization, X-ray crystal structure of [(CH2=CHCH2)CH3Si(C13H8)(2)]ZrCl2

A series of ansa-metallocene complexes with an allyl substituted silane bridge [(CH =CHCH2)CH3Si(C5H4)(2)]TiCl2 (1), [(CH2=CHCH2)CH3Si(C9H6)(2)]MCl2 [M = Ti (2), Zr (3), Hf (4)] and [(CH2=CHCH2)CH3Si(C13H8)(2)]ZrCl2 (6) have been synthesized and characterized. The molecular structure of 6 has been determined by X-ray crystallographic analysis. Complexes 1-4, 6 bearing allyl groups have been investigated as self-immobilized catalysts for ethylene polymerization in the presence of MMAO. The results showed that the self-immobilized catalysts 1-4, 6 kept high ethylene polymerization activities of ca. 10(6) g PE mol(-1) M h(-1) and high molecular weight (M-w approximate to 10(5)) of polyethylene.

catena-Poly[[[2-(2-furyl)-1H-imidazo[4,5-f][1,10]phenanthroline]zinc(II)]-mu-benzene-1,2-dicarboxylato]

In the title compound, [Zn(C8H4O4)(C17H10N4O)](n), the Zn-II atom is five-coordinated by two N atoms from the phenanthro-line-derived ligand and three O atoms from one bidentate and one monodentate benzene-1,2-dicarboxylate (1,2-BDC) dianions in a distorted trigonal-bipyramidal geometry. The Zn-II atoms are bridged by the 1,2-BDC ligands to form a single-chain structure. Neighboring chains interact through pi-pi interactions, leading to a two-dimensional network.

填充油的种类对Fe系1,2-聚丁二烯性能的影响

研究了芳烃油和环烷烃油对充油铁系1,2-聚丁二烯橡胶性能的影响。结果表明,基础胶充油后门尼粘度值下降,可塑性增加,混炼行为变佳;填充芳烃油比填充环烷烃油的橡胶在拉伸强度、撕裂强度、伸长率和生胶门尼值等方面均有所提高;充油后虽然硫化胶硬度降低,但是生热和耐磨性能提高。填充芳烃油可适当提高硫化胶的抗湿滑性,但滚动阻力也升高。环烷烃油可降低硫化胶的滚动阻力。充油可适当改善胶料的抗老化性能。

间同立构1,2-聚丁二烯的合成和形态结构研究

间同立构1,2-聚丁二烯自1955年问世以来 ,引起人们的广泛关注 ,但绝大多数研究工作集中在聚合物的合成方面[1～3] ,对其形态结构方面的研究却很少报道[4] ,原因是该聚合物分子侧链含有大量双链 ,在较高温度下 (>150℃ )很容易产生热交联 ,这给结构研究造成了很大困难 .间同立构1,2-聚丁二烯的性能取决于间规度 ,低间规度聚合物呈现弹性体特征 ,而高间规度聚合物则是一种半结晶性塑料 ,其结晶为平面锯齿链正交堆砌 ,Pacm空间群[4] .本文采用一种新的催化体系 ,使合成的1,2-聚丁二烯间规度可以调控.同时首次报道了结晶性间规1,2-聚丁二烯稀溶液浇铸薄膜形成具有单晶取向的板条状片层结构,并应用电子显微学和电子衍射技术确定其晶体结构.1.实验部分1.1样品及试剂　乙酰基丙酮铁 [(Fe(acac) 3)纯度为 99.9% ],使用时配成0.2mol/ L的甲苯溶液 ;三异丁基铝 [Al(i-Bu) 3]由 Aldrich公司提供 ;氢化亚磷酸二乙酯 (DEP)及丁二烯由锦州化学公司提供 ;丁二烯通过蒸馏进行纯化 ;己烷使用前在 Na/ K合金...

结晶性间同立构1,2-聚丁二烯的单晶结构

近十几年来,结晶性间同立构1,2-聚丁二烯引起人们的广泛关注,但绝大多数研究工作集中在聚合物的制备、物理性质和应用方面[1～3],对于其结晶行为和晶体结构则未见报道 .原因是间同立构1,2-聚丁二烯分子侧链含有大量的双键,在较高温度下很容易交联 ,特别是高间规度的聚合物 ,由于其熔融温度高 (>200℃ )则更易产生交联,这给结晶行为和结构研究带来很大困难.结晶性间同立构1,2-聚丁二烯的晶体结构为平面锯齿链正交堆砌,Pacm空间群[4].我们曾报道了结晶性间同立构1,2-聚丁二烯的合成和溶液浇铸膜的板条状结构[5],本文采用薄膜熔体结晶的方法第一次成功地获得了间同立构1,2-聚丁二烯的单晶,并通过电子显微学和电子衍射技术确定了其晶体结构.1 实验部分1.1间同立构1,2-聚丁二烯的制备采用乙酰基丙酮铁 [Fe(acac) ]3、三异丁基铝 [Al(i-Bu)3]和氢化亚磷酸二乙酯 (DEP)的新催化体系制备间同立构1,2-聚丁二烯,具体合成路线参见文献 [5].本文所选用聚合物的1,2单元含量为 89.3 % ,间规度为 ...

A novel 2D arsenic vanadate network grafted with a transition metal complex: [Cu(phen)][(VV4As2O19)-V-IV-As-V]center dot 0.5H(2)O

A novel organic-inorganic hybrid compound [Cu(phen)](2)[(VV4As2O19)-V-IV-As-V-O-V].0.5H(2)O 1 has been hydrothermally synthesized. Its structure, determined by single crystal X-ray diffraction, exhibits an unusual two-dimensional arsenic vanadate layered network grafted with the [Cu(phen)](2+) complex. The chelating phen ligands project perpendicularly beyond the inorganic layer. Variable temperature magnetic susceptibility studies indicate that both ferro- and antiferro-magnetic interactions exist in 1.

Novel two-dimensional sodium molybdenum phosphates containing {M(enMe)(2)}(2+) bridging groups (M = Ni, Cu; enMe=1,2-diaminopropane)

Two novel organic-inorganic hybrid compounds, (H(2)enMe)(4)(H3O)[Ni(enMe)(2)].[Na3Mo12O52P8(OH)(10)].5H(2)O (1) and (H(2)enMe)(4)(H3O)[Cu(enMe)(2)].[Na3Mo12O52P8(OH)(10)].5H(2)O (2) (enMe = 1,2-diaminopropane), have been hydrothermally synthesized and characterized by elemental analyses, IR, EPR, XPS, UV-Vis spectra and TG analyses. Single crystal X-ray diffraction shows that 1 and 2 are isostructural compounds. Both the compounds exhibit an unusual two-dimensional (2-D) window-like network consisting of one-dimensional (1-D) chains of sodium molybdenum phosphate anions connected by transition metal coordination complexes cations. Compound 1 and 2 represent the first 2-D molybdenum phosphate skeleton pillared by transition metal complex fragments.