Evaluation of various pre-treatments for the dehydration of banana and selection of suitable drying models

The thin-layer drying behaviour of bananas in a beat pump dehumidifier dryer was examined. Four pre-treatments (blanching, chilling, freezing and combined blanching and freezing) were applied to the bananas, which were dried at 50 degreesC with an air velocity of 3.1 m s(-1) and with the relative humidity of the inlet air of 10-35%. Three drying models, the simple model, the two-term exponential model and the Page model were examined. All models were evaluated using three statistical measures, correlation coefficient, root means square error, and mean absolute percent error. Moisture diffusivity was calculated based on the diffusion equation for an infinite cylindrical shape using the slope method. The rate of drying was higher for the pre-treatments involving freezing. The sample which was blanched only did not show any improvement in drying rate. In fact, a longer drying time resulted due to water absorption during blanching. There was no change in the rate for the chilled sample compared with the control. While all models closely fitted the drying data, the simple model showed greatest deviation from the experimental results. The two-term exponential model was found to be the best model for describing the drying curves of bananas because its parameters represent better the physical characteristics of the drying process. Moisture diffusivities of bananas were in the range 4.3-13.2 x 10(-10) m(2)s(-1). (C) 2002 Published by Elsevier Science Ltd.

Exposure to automotive pollution increases plasma susceptibility to oxidation

Low-density lipoprotein oxidation is implicated in the development of atherosclerosis. Plasma susceptibility to oxidation may be used as a marker of low-density lipoprotein oxidation and thus predict atherosclerotic risk. In this study the authors investigated the relationship between plasma susceptibility to oxidation and exposure to automotive pollution in a group of automobile mechanics (n = 16) exposed to high levels of automotive pollution, vs. matched controls (n = 13). The authors induced plasma oxidation by a free radical initiator and they determined susceptibility to oxidation by (1) change in absorbance at 234 nm, (2) lag time to conjugated diene formation, and (3) linear slope of the oxidation curve. Mechanics had significantly higher values (mean standard error) for change in absorbance (1.60 +/- 0.05 vs. 1.36 +/- 0.05; p < .002), and slope (1.6 x 10(-3) +/- 0.1 x 10(-3) vs. 1.3 x 10(-3) +/- 0.1 x 10(-3); p < .001), compared with controls. These results indicate that regular exposure to automotive pollutants increases plasma susceptibility to oxidation and may, in the long term, increase the risk of developing atherosclerosis.

An electromyographic analysis of the deep cervical flexor muscles in performance of craniocervical flexion

Background and Purpose. This study evaluated an electromyographic technique for the measurement of muscle activity of the deep cervical flexor (DCF) muscles. Electromyographic signals were detected from the DCF, sternocleidomastoid (SCM), and anterior scalene (AS) muscles during performance of the craniocervical flexion (CCF) test, which involves performing 5 stages of increasing craniocervical flexion range of motion-the anatomical action of the DCF muscles. Subjects. Ten volunteers without known pathology or impairment participated in this study. Methods. Root-mean-square (RMS) values were calculated for the DCF, SCM, and AS muscles during performance of the CCF test. Myoelectric signals were recorded from the DCF muscles using bipolar electrodes placed over the posterior oropharyngeal wall. Reliability estimates of normalized RMS values were obtained by evaluating intraclass correlation coefficients and the normalized standard error of the mean (SEM). Results. A linear relationship was evident between the amplitude of DCF muscle activity and the incremental stages of the CCF test (F=239.04, df=36, P<.0001). Normalized SEMs in the range 6.7% to 10.3% were obtained for the normalized RMS values for the DCF muscles, providing evidence of reliability for these variables. Discussion and Conclusion. This approach for obtaining a direct measure of the DCF muscles, which differs from those previously used, may be useful for the examination of these muscles in future electromyographic applications.

Usefulness of quantitative echocardiographic techniques to predict recovery of regional and global left ventricular function after acute myocardial infarction

The left ventricular response to dobutamine may be quantified using tissue Doppler measurement of myocardial velocity or displacement or 3-dimensional echocardiography to measure ventricular volume and ejection fraction. This study sought to explore the accuracy of these methods for predicting segmental and global responses to therapy. Standard dobutamine and 3-dimensional echocardiography were performed in 92 consecutive patients with abnormal left ventricular function at rest. Recovery of function was defined by comparison with follow-up echocardiography at rest 5 months later. Segments that showed improved regional function at follow-up showed a higher increment in peak tissue Doppler velocity with dobutamine therapy than in nonviable segments (1.2 +/- 0.4 vs 0.3 +/- 0.2 cm/s, p = 0.001). Similarly, patients who showed a > 5% improvement of ejection fraction at follow-up showed a greater displacement response to dobutamine (6.9 +/- 3.2 vs 2.1 +/- 2.3 mm, p = 0.001), as well as a higher rate of ejection fraction, response to dobutamine (9 +/- 3% vs 2 +/- 2%, p = 0.001). The optimal cutoff values for predicting subsequent recovery of function at rest were an increment of peak velocity > 1 cm/s, >5 mm of displacement, and a >5% improvement of ejection fraction with low-dose dobutamine. (C) 2003 by Excerpta Medica, Inc.

Surface stickiness of drops of carbohydrate and organic acid solutions during convective drying: Experiments and modeling

Drying kinetics of low molecular weight sugars such as fructose, glucose, sucrose and organic acid such as citric acid and high molecular weight carbohydrate such as maltodextrin (DE 6) were determined experimentally using single drop drying experiments as well as predicted numerically by solving the mass and heat transfer equations. The predicted moisture and temperature histories agreed with the experimental ones within 6% average relative (absolute) error and average difference of +/- 1degreesC, respectively. The stickiness histories of these drops were determined experimentally and predicted numerically based on the glass transition temperature (T-g) of surface layer. The model predicted the experimental observations with good accuracy. A nonsticky regime for these materials during spray drying is proposed by simulating a drop, initially 120 mum in diameter, in a spray drying environment.

O impacto da exposição a experiências adversas na infância na ocorrência de dor crônica e depressão na vida adulta

A associação entre experiências adversas na infância e o desencadeamento de depressão ou dor crônica na vida adulta tem sido documentada, assim como a relação entre os sintomas de dor crônica e depressão. No entanto, há poucos estudos avaliando o papel da exposição a experiências adversas na infância na ocorrência dessa comorbidade. O objetivo deste trabalho é avaliar a influência da exposição a experiências adversas na infância na ocorrência de dor crônica, de depressão e na comorbidade dor crônica e depressão na vida adulta, em uma amostra da população geral adulta (maiores de 18 anos) residente na Região metropolitana de São Paulo, Brasil. Os dados são resultantes do Estudo Epidemiológicos dos Transtornos Mentais São Paulo Megacity. Os respondentes foram avaliados usando a versão desenvolvida para o Estudo Mundial de Saúde Mental do Composite International Diagnostic Interview da Organização Mundial da Saúde (WMH-CIDI), que é composto por módulos clínicos e nãoclínicos provendo diagnósticos de acordo com os critérios do Manual Diagnóstico e Estatístico dos Transtornos Mentais 4ª edição (DSM-IV). Um total de 5.037 indivíduos foi entrevistado, com uma taxa global de resposta de 81,3%. Foram realizadas análises descritivas para médias e proporções, e associações (Razões de Chances – OR) entre experiências adversas na infância, dor crônica e depressão através de regressão logística. Todas as análises foram realizadas através do programa estatístico Data Analysis and Statistical Software versão 12.0 (STATA 12.0), com testes bi-caudais com nível de significância de 5%. Uma elevada taxa de prevalência de dor crônica (31%, Erro Padrão [ER]=0.8) foi encontrada, Dor Crônica esteve associada aos transtornos de ansiedade (OR=2,3; 95% IC=1,9 – 3,0), transtornos de humor (OR=3,3; IC=2,6 – 4,4) em qualquer transtorno mental (OR=2,7; 95% IC=2,3 – 3,3). As adversidades na infância estiveram fortemente associadas aos respondentes com dor crônica e depressão concomitante, principalmente quanto ao abuso físico (OR=2,7; 95% IC=2,1 – 3,5) e sexual (OR=7,4; 95% IC=3,4 – 16,1).

Estudo da cinética e influência dos métodos de secagem sobre as propriedades físico-químicas de soro de leite

O soro de leite é um subproduto da fabricação do queijo, seja por acidificação ou por processo enzimático. Em condições ideais, a caseína do leite se agrega formando um gel, que posteriormente cortado, induz a separação e liberação do soro. É utilizado de diversas formas em toda a indústria alimentícia, possui rica composição em lactose, sais minerais e proteínas. A desidratação é um dos principais processos utilizados para beneficiamento e transformação do soro. Diante disto, o objetivo deste trabalho foi avaliar a influência dos métodos de secagem: liofilização, leito de espuma (nas temperaturas de 40, 50, 60, 70 e 80ºC) e spray-dryer (nas temperaturas de 55, 60, 65, 70 e 75ºC), sobre as características de umidade, proteína, cor e solubilidade do soro, bem como estudar o seu processo de secagem. O soro foi obtido e desidratado após concentração por osmose reversa, testando 11 tratamentos, em 3 repetições, utilizando um delineamento inteiramente casualizado. Os resultados demonstraram que o modelo matemático que melhor se ajustou foi o modelo de Page, apresentado um coeficiente de determinação ajustado acima de 0,98 e erro padrão da regressão em todas as temperaturas abaixo de 0,04 para o método por leito de espuma. Para o método de liofilização os respectivos valores foram 0,9975 e 0,01612. A partir disso, pode-se elaborar um modelo matemático generalizado, apresentando um coeficiente de determinação igual a 0,9888. No caso do leito de espuma, observou-se que à medida que se aumenta a temperatura do ar de secagem, o tempo de secagem diminui e os valores do coeficiente de difusão efetiva aumentam. Porém, a redução no tempo de secagem entre os intervalos de temperatura, diminui com o aumento da mesma. A energia de ativação para a difusão no processo de secagem do soro foi de 26,650 kJ/mol e para todas as avaliações físico-químicas e tecnológicas, a análise de variância apresentou um valor de F significativo (p<0,05), indicando que há pelo menos um contraste entre as médias dos tratamentos que é significativo.

EVALUATING THE EFFICIENCY PROGRESS WITH TECHNOLOGY IN A SPANISH HOTEL CHAIN

ABSTRACTThis paper analyzes the changes in the total factor productivity index of a Spanish hotel chain in the period from 2007 to 2010 with the purpose of identifying efficiency patterns for the chain in a period of financial crisis. The data envelopment analysis (DEA) Malmquist productivity index was used to estimate productivity change in 38 hotels of the AC chain. Results reveal AC hotels' efficiency trends and, therefore, their competitiveness in the recession period; they also show the changes experienced in these hotels' total productivity and its components: technological and efficiency changes. Positive efficiency changes were due to positive technical efficiency rather than technological efficiency. The recession period certainly influenced the performance of AC Hotels, which focused on organizational changes rather than investing in technology.

Validity of self-reported weight: a study of urban brazilian adults

In order to evaluate the validity of self-reported weight for use in obesity prevalence surveys, self-reported weight was compared to measured weight for 659 adults living in the Porto Alegre county, RS Brazil in 1986-87, both weights being obtained by a technician in the individual's home on the same visit. The mean difference between self-reported and measured weight was small (-0.06 +/- 3.16 kg; mean +/- standard deviation), and the correlation between reported and measured weight was high (r=0.97). Sixty-two percent of participants reported their weight with an error of < 2 kg, 87% with an error of < 4 kg, and 95% with an error of < 6 kg. Underweight individuals overestimated their weight, while obese individuals underestimated theirs (p<0.05). Men tended to overestimate their weight and women underestimate theirs, this difference between sexes being statistically significant (p=0.04). The overall prevalence of underweight (body mass index < 20) by reported weight was 11%, by measured weight 13%; the overall prevalence of obesity (body mass index > 30) by reported weight was 10%, by measured weight 11%. Thus, the validity of reported weight is acceptable for surveys of the prevalence of ponderosity in similar settings.

Information and communication technologies in education – a web-based intelligent tutoring system on teaching and learning electrical project

Electrical activity is extremely broad and distinct, requiring by one hand, a deep knowledge on rules, regulations, materials, equipments, technical solutions and technologies and assistance in several areas, as electrical equipment, telecommunications, security and efficiency and rational use of energy, on the other hand, also requires other skills, depending on the specific projects to be implemented, being this knowledge a characteristic that belongs to the professionals with relevant experience, in terms of complexity and specific projects that were made.

Evolução de software e serviços Web

A Internet causou uma revolução em grande parte dos processos das empresas, criando oportunidades e gerando necessidades até então desconhecidas. Os Sistemas de Informação, ferramentas indispensáveis para uma gestão moderna das actividades empresariais, também foram influenciados pela evolução constante da tecnologia e as facilidades oferecidas para a popularização do uso da Internet. Rumo a uma crescente necessidade de modernização, rapidez, agilidade, eficiência e eficácia que são exigidos das actividades da empresa, actualmente, a tecnologia da Web é exibida como uma opção viável para melhorar o desempenho na gestão da informação. Esta Tese procura dissertar acerca dos aspectos relativos ao funcionamento e implementação de Serviços Web, suas principais características, vantagens e desvantagens comparativamente aos sistemas de informação tradicionais. Os objectivos propostos podem ser sintetizados no conhecimento e descrição das funcionalidades dos Serviços Web, no estudo da situação actual, na identificação das características que potenciam a capacidade de evolução dos Serviços Web, no estudo e desempenho dos Serviços Web, e finalmente, no estudo e análise da especificação Segurança.

Soil vapor extraction in sandy soils: influence of airflow rate

Airflow rate is one of the most important parameters for the soil vapor extraction of contaminated sites, due to its direct influence on the mass transfer occurring during the remediation process. This work reports the study of airflow rate influence on soil vapor extractions, performed in sandy soils contaminated with benzene, toluene, ethylbenzene, xylene, trichloroethylene and perchloroethylene. The objectives were: (i) to analyze the influence of airflow rate on the process; (ii) to develop a methodology to predict the remediation time and the remediation efficiency; and (iii) to select the most efficient airflow rate. For dry sandy soils with negligible contents of clay and natural organic matter, containing the contaminants previously cited, it was concluded that: (i) if equilibrium between the pollutants and the different phases present in the soil matrix was reached and if slow diffusion effects did not occur, higher airflow rates exhibited the fastest remediations, (ii) it was possible to predict the remediation time and the efficiency of remediation with errors below 14%; and (iii) the most efficient remediation were reached with airflow rates below 1.2 cm3 s 1 standard temperature and pressure conditions.

Soil remediation time to achieve clean-up goals II: influence of natural organic matter and water contents

This work reports a relatively rapid procedure for the forecasting of the remediation time (RT) of sandy soils contaminated with cyclohexane using vapour extraction. The RT estimated through the mathematical fitting of experimental results was compared with that of real soils. The main objectives were: (i) to predict the RT of soils with natural organic matter (NOM) and water contents different from those used in experiments; and (ii) to analyse the time and efficiency of remediation, and the distribution of contaminants into the soil matrix after the remediation process, according to the soil contents of: (ii1) NOM; and (ii2) water. For sandy soils with negligible clay contents, artificially contaminated with cyclohexane before vapour extraction, it was concluded that: (i) if the NOM and water contents belonged to the range of the prepared soils, the RT of real soils could be predicted with relative differences not higher than 12%; (ii1) the increase of NOM content from 0% to 7.5% increased the RT (1.8–13 h) and decreased the remediation efficiency (RE) (99–90%) and (ii2) the increase of soil water content from 0% to 6% increased the RT (1.8–4.9 h) and decreased the RE (99–97%). NOM increases the monolayer capacity leading to a higher sorption into the solid phase. Increasing of soil water content reduces the mass transfer coefficient between phases. Concluding, NOM and water contents influence negatively the remediation process, turning it less efficient and more time consuming, and consequently more expensive.

Statistical analysis of quality control measurements in IMRT for head and neck and prostate cancer

Intensity Modulated Radiotherapy (IMRT) is a technique introduced to shape more precisely the dose distributions to the tumour, providing a higher dose escalation in the volume to irradiate and simultaneously decreasing the dose in the organs at risk which consequently reduces the treatment toxicity. This technique is widely used in prostate and head and neck (H&N) tumours. Given the complexity and the use of high doses in this technique it’s necessary to ensure as a safe and secure administration of the treatment, through the use of quality control programmes for IMRT. The purpose of this study was to evaluate statistically the quality control measurements that are made for the IMRT plans in prostate and H&N patients, before the beginning of the treatment, analysing their variations, the percentage of rejected and repeated measurements, the average, standard deviations and the proportion relations.

Auditoria energética e plano de racionalização de energia

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Mecânica