Efeito da adição de fibras da palma do licuri (syagrus coronata) no comportamento físico e mecânico de compósitos de matriz cimentícia

This research was motivated by the requirement of asbestos s replacement in building systems and the need to generate jobs and income in the country side of the state of Bahia, Brazil. The project aimed at using fibers from licuri leaves (syagrus coronata), an abundant palm in the region, to produce composites appropriate for the sustainable production of cement fibre reinforced products in small plants. The composites were produced in laboratory using Portland cement CP-II-F32, sand, water, licuri palm fiber contents of 1.0, 1.5 and 2.0% by weight of binder (two different fiber length) and metakaolin. The latter was chosen as an additional binder for its efficiency to reduce the alkalinity of cementitious matrixes therefore preventing the degradation of vegetable fibers. The characterization of the composite components was carried out by sieving and laser particle size analyses, thermal analysis, fluorescence and X-ray diffraction. The composites performance was evaluated by 3- point-bending tests, compressive strength, ultrasound module of elasticity, free and restrained shrinkage, water capillarity absorption and apparent specific gravity. It has been found that the addition of fibers increased the time to onset of cracking over 200.00% and a 25% reduction in cracks opening in the restrained shrinkage test. The capillary absorption reduced about 25% when compared to fiber-free composites. It was also observed with regard to flexural strength, compressive strength and specific gravity, that the addiction of fibers did not affect the composite performance presenting similar results for compounds with and without fibers. In general it can be stated that the reinforced composite fibers of palm licuri presents physical and mechanical characteristics which enable them to be used in the intended proposals of this research

Origem física das curvas sigmoidais respiratórias pressão-volume: recrutamento alveolar e elasticidade não-linear

An important unsolved problem in medical science concerns the physical origin of the sigmoidal shape of pressure volume curves of healthy (and some unhealthy) lungs. Such difficulties are expected because the lung, which is the most important structure in the respiratory system, is extremely complex. Its rheological properties are unknown and seem to depend on phenomena occurring from the alveolar scale up to the thoracic scale. Conventional wisdom holds that linear response, i.e., Hooke s law, together with alveolar overdistention, play a dominant role in respiration, but such assumptions cannot explainthe crucial empirical sigmoidal shape of the curves. In this doctorate thesis, we propose an alternative theory to solve this problem, based on the alveolar recruitment together with the nonlinear elasticity of the alveoli. This theory suggests that recruitment may be the predominant factor shaping these curves in the entire range of pressures normally employed in experiments. The proposed model correctly predicts the observed sigmoidal pressure volume curves, allowing us to discuss adequately the importance of this result, as well as its implications for medical practice

Crescimento econômico e restrição externa da economia brasileira: uma análise do padrão das exportações em relação ao BRIC e do Sistema de Inovação do Brasil (1980-2012)

This Master s Thesis aims to use the theoretical models of growth with restricted balance of payments, specifically Kaldor (1970) and Thirlwall (1979) models, to analyze the behavior and the pattern of specialization of Brazilian exports and imports in the last years. It is observed that, in some periods, the pattern of specialization has contributed in restricting long-term growth of the Brazilian economy. It has been hypothesized that overall this is due to lack of structural transformation policies. To achieve this goal, it analyzed the performance of Brazilian exports and imports disaggregating them according to their technological content. The basis for comparison was a group of countries to which Brazil is inserted in, the BRIC. In this regard, the work is a comparative analysis by using descriptive statistics. It is concluded that the low rate of GDP growth experienced by Brazil since the 1980s can be explained in part by the decoupling of the Brazilian National Innovation System (NIS) and the Brazilian productive structure. This would be reducing the income elasticity of exports and raising imports, causing a pattern of specialization intensive primary commodities and labor and low-skill labor

Crescimento econômico e restrição externa: evidências empíricas na economia brasileira (1991-2010)

This study aims to investigate the influence of the balance of payments constrained on economic growth in Brazil from 1991 to 2010. With this order, are shown some of the Keynesian balance of payments constrained growth models, inspired by Thirlwall (1979) and Kaldor (1970), which are supported by important points in common, such as adherence to the principle of effective demand. Given that within this theoretical perspective, there is no consensus about the best model to explain the growth rate allowed by the balance of payments constraint, the results are presented by the representative of the empirical literature that addresses the topic, which are necessary for understand the Brazilian case. From the estimation of the income elasticity of imports (0.85) via autoregressive vectors with error correction (VEC), it was calculated five growth rates of income, as predicted by the models of Thirlwall (1979), Thirlwall and Hussain (1982), Moreno-Brid (1998, 2003) and Lourenço et al. (2011) and compared with the actual growth rate. The empirical analysis has shown that: it can not reject the presence of external constraint in the Brazilian economy, there is a strong similarity in growth rates provided by different modeling suggest that growth with external constraint. In addition, when using data in quarterly for the period after 1990 there are no factors that could cause instability in the parameters of the import function (income elasticity and price elasticity of imports) within the period, which indicates that the structural break widely associated with the year 1994 was not confirmed by this study

A elasticidade do ligamento colateral medial da articulação do cotovelo de cão não advém de elastina

A literatura relata que ligamentos consistem de tecido conjuntivo denso, composto por água, colágeno tipos I e III, diversas proteoglicanas, pouca elastina e várias outras substâncias. Além disso, os ligamentos, quando testados in vitro com tensão longitudinal e unidirecional, apresentam um comportamento mecânico não-linear, ou seja, as fibras colágenas são alongadas aos poucos, perdendo seu padrão ondulado, até que todas estejam no limite máximo de tração e iniciem o rompimento. Portanto, no presente estudo avaliou-se a presença de fibras elásticas (elastina) no ligamento colateral medial do cotovelo de cães adultos para ponderar se a elasticidade do referido ligamento deve-se à presença de fibras elásticas ou às propriedades elásticas do colágeno ou à combinação de ambas. Foram utilizadas quatro articulações, de machos e fêmeas em igual proporção, das quais foram adquiridas as amostras das porções médias dos ligamentos colaterais mediais para a rotina histológica. Os cortes foram corados pela técnica de Weigert, e não foi observada a presença de fibras elásticas, detectável por esta técnica à microscopia de luz. Concluiu-se que a elasticidade do ligamento colateral medial do cotovelo de cão deve-se, principalmente, ao padrão ondulado das fibras colágenas, devido à quantidade ínfima ou até à inexistência de fibras elásticas nesta estrutura.

Propriedades mecânicas de três padrões de sutura no reparo de tendão do músculo flexor profundo do dedo em eqüinos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo de concretos de diferentes resistências à compressão submetidos a altas temperaturas sem e com incorporação de fibras de politereftalato de etileno (PET)

The reinforced concrete structures are largely used in buildings worldwide. Upon the occurrence of fire in buildings, there is a consensus among researchers that the concrete has a high resistance to fire, due mainly to its low thermal conductivity. However, this does not mean that this material is not affected by exposure to high temperatures. Reduction of the compressive strength, modulus of elasticity, discoloration and cracking, are some of the effects caused by thermal exposure. In the case of concretes with higher resistance occurs even desplacamentos explosives, exposing the reinforcement to fire and contributing to reducing the support capacity of the structural element. Considering the above, this study aims to examine how the compressive strength and porosity of concrete are affected when subjected to high temperatures. Were evaluated concrete of different resistances, and even was the verified if addition fibers of polyethylene terephthalate (PET) in concrete can be used as an alternative to preventing spalling. The results indicated that explosive spalling affect not only high strength concrete whose values of this study ranged from 70 to 88 MPa, as well as conventional concrete of medium strength (52 MPa) and the temperature range to which the concrete begins to suffer significant changes in their resistance is between 400 º C and 600 º C, showing to 600 º C a porosity up to 188% greater than the room temperature

Physical and mechanical properties of thermally modified wood from E. grandis

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Propriedades de resistência e rigidez da madeira juvenil e adulta de Pinus taeda L.

O objetivo do presente trabalho foi o estudo da variabilidade das propriedades de resistência e rigidez à flexão estática e à densidade aparente (12%) entre a madeira juvenil e adulta de Pinus taeda L., de 37 anos de idade, procedente do Horto Florestal de Manduri, Estado de São Paulo. Na primeira parte do trabalho foram determinadas a região de madeira juvenil, a região de transição e a região de madeira adulta, por meio de estudos anatômicos (comprimento dos traqueídes axiais), segundo as recomendações das normas ABNT e IAWA. Os resultados mostraram que a região de madeira juvenil dessa espécie ocorre aproximadamente até o 18º anel de crescimento. Na segunda parte do trabalho foram analisados a resistência (módulo de ruptura - MOR) à flexão, o módulo de elasticidade (MOE) nessa mesma solicitação e a densidade aparente (12%) para as madeiras juvenil e adulta. Os resultados mostraram que o MOE e o MOR da madeira juvenil foram menores e mais variáveis que aqueles obtidos para madeira adulta. A densidade apresentou a mesma tendência observada nas propriedades avaliadas no ensaio de flexão estática.

Determinação do módulo de elasticidade da madeira juvenil e adulta de Pinus taeda por ultra-som

A madeira de Pinus sp. tem utilização crescente na indústria madeireira brasileira. O decréscimo constante do suprimento de árvores adultas com grandes diâmetros, provenientes de florestas naturais, tornou comum a produção de madeira em ciclos curtos, com grande proporção de madeira juvenil. Resultados de diversas pesquisas têm reportado que o módulo de elasticidade e a resistência a diferentes solicitações mecânicas são seriamente afetados pela presença de madeira juvenil. Este trabalho teve por objetivo determinar o módulo de elasticidade da madeira juvenil e adulta de Pinus taeda L. a partir da constante dinâmica C LL, obtida em ensaios não-destrutivos de ultra-som. A madeira de P. taeda era originária de plantios da Estação Experimental de Itapeva - SP, sendo amostrados seis indivíduos arbóreos com 34 anos de idade. Os corpos-de-prova (4 cm x 4 cm x 45 cm) foram obtidos separadamente das regiões de madeira juvenil e adulta da prancha central, previamente submetida à secagem industrial (umidade final de 12%), para a determinação da constante dinâmica por meio de ensaios de ultra-som. Para avaliar a sensibilidade do método do ultra-som, os corpos-de-prova foram ensaiados destrutivamente à compressão paralela. Os resultados mostraram boa sensibilidade do método do ultra-som (R² » 0,90) na avaliação desse parâmetro mecânico da madeira juvenil e adulta.

Estudo das propriedades mecânicas de biocompósitos de polipropileno reforçados com fibras naturais

This research presents an approach to the addition of curauá fibers and licuri fibers in a polypropylene resin matrix, such as an alternative proposal to reinforce the polymeric composites. Fiber content of 0 %, 5 %, 10 %, and 20% were analyzed for verification of their mechanical properties comparing them, inclusive with the properties of polypropylene. The grainulated biocomposites had been prepared in an extrusora. The test bodies had been molded by injection and submitted to the mechanical essays uniaxial traction, flexion on three points, impact, in addition to thermal tests (HDT). These biocomposites had been also subjected the essay physicist-chemistry index of fluidity (IF). It was observed that the biocomposites of PP with 20% curauá, obtained bigger increase in the modulus of elasticity and a bigger reduction in the resistance to the impact. In the mechanical behavior, for all the biocomposites, these were increases in values of the limit of drainage and tension of rupture, when tested by uniaxial traction, as they added the fibers. Another important point was the increase of the resistance the flexion. It was also noted that the addition of fibers reduced the thermal degradation of the mixture natural fibers / polypropylene.

Previsão do módulo de elasticidade transversal de compósitos unidirecionais através de redes neurais mistas

The aim of this study is to create an artificial neural network (ANN) capable of modeling the transverse elasticity modulus (E2) of unidirectional composites. To that end, we used a dataset divided into two parts, one for training and the other for ANN testing. Three types of architectures from different networks were developed, one with only two inputs, one with three inputs and the third with mixed architecture combining an ANN with a model developed by Halpin-Tsai. After algorithm training, the results demonstrate that the use of ANNs is quite promising, given that when they were compared with those of the Halpín-Tsai mathematical model, higher correlation coefficient values and lower root mean square values were observed

Thermomechanical characterization of PVDF and P(VDF-TrFE) blends containing corn starch and natural rubber

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Modeling a system of phosphated cross-linked high amylose for controlled drug release. Part 2: Physical parameters, cross-linking degrees and drug delivery relationships

High amylose cross-linked to different degrees with sodium trimetaphosphate by varying base strength (2% or 4%) and contact time (0.5-4 h) was evaluated as non-compacted systems for sodium diclophenac controlled release. The physical properties and the performance of these products for sodium diclophenac controlled release from non-compacted systems were related to the structures generated at each cross-linking degree. For samples at 2% until 2 h the swelling ability, G' and eta* values increased with the cross-linking degree, because the longer polymer chains became progressively more entangled and linked. This increases water uptake and holding, favoring the swelling and resulting in systems with higher viscosities. Additionally, the increase of cross-linking degree should contribute for a more elastic structure. The shorter chains with more inter-linkages formed at higher cross-linking degrees (2%4h and 4%) make water caption and holding difficult, decreasing the swelling, viscosity and elasticity. For 2% samples, the longer drug release time exhibited for 2%4h sample indicates that the increase of swelling and viscosity contribute for a more sustained drug release, but the mesh size of the polymeric network seems to be determinant for the attachment of drug molecules. For the 4% samples, smaller meshes size should determine less sustained release of drug. (C) 2008 Elsevier B.V. All rights reserved.

Structural characterization and in vivo evaluation of retinyl palmitate in non-ionic lamellar liquid crystalline system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)