Characterizing Physical Properties of Wetting Paper by Air Coupled Ultrasound and Light

This thesis reports investigations into the paper wetting process and its effects on the surface roughness and the out-of-plane (ZD) stiffness of machine-made paper. The aim of this work was to test the feasibility of employing air-borne ultrasound methods to determine surface roughness (by reflection) and ZD stiffness (by through transmission) of paper during penetration of distilled water, isopropanol and their mixtures. Air-borne ultrasound provides a non-contacting way to evaluate sample structure and mechanics during the liquid penetration event. Contrary to liquid immersion techniques, an air-borne measurement allows studying partial wetting of paper. In addition, two optical methods were developed to reveal the liquid location in paper during wetting. The laser light through transmission method was developed to monitor the liquid location in partially wetted paper. The white light reflection method was primarily used to monitor the penetration of the liquid front in the thickness direction. In the latter experiment the paper was fully wetted. The main results of the thesis were: 1) Liquid penetration induced surface roughening was quantified by monitoring the ultrasound reflection from the paper surface. 2) Liquid penetration induced stiffness alteration in the ZD of paper could be followed by measuring the change in the ultrasound ZD resonance in paper. 3) Through transmitted light revealed the liquid location in the partially wetted paper. 4) Liquid movement in the ZD of the paper could be observed by light reflection. The results imply that the presented ultrasonic means can without contact measure the alteration of paper roughness and stiffness during liquid transport. These methods can help avoiding over engineering the paper which reduces raw material and energy consumption in paper manufacturing. The presented optical means can estimate paper specific wetting properties, such as liquid penetration speed, transport mechanisms and liquid location within the paper structure. In process monitoring, these methods allow process tuning and manufacturing of paper with engineered liquid transport characteristics. With such knowledge the paper behaviour during printing can be predicted. These findings provide new methods for paper printing, surface sizing, and paper coating research.

Thermal properties of MOSi2 with minor aluminum substitutions

Mo(Si1-xAlx)(2) compositions (x = 0-0.1) have been prepared by a modified SHS route under uniaxial hydrostatic pressure. Oxidation studies carried out by thermal analysis and sheet resistivity indicate an improvement in the low temperature (700-900 K) oxidation resistance with increasing aluminum addition. Dilatometric results show a decrease in the a value up to x = 0.05 substitution. With the aluminum substitution, both thermal expansion coefficient and thermal conductivity show decrease in their values except in the biphasic region. The x = 0.05 composition containing both C11(b) and C40 phases is a promising material for high temperature thermal barrier coating as it shows higher oxidation resistance and a similar K/alpha value as compared to pure MoSi, (c) 2006 Elsevier Ltd. All rights reserved.

Food waste, power, and corporate social responsibility in the Australian food supply chain

By examining corporate social responsibility (CSR) and power within the context of the food supply chain, this paper illustrates how food retailers claim to address food waste while simultaneously setting standards that result in the large-scale rejection of edible food on cosmetic grounds. Specifically, this paper considers the powerful role of food retailers and how they may be considered to be legitimately engaging in socially responsible behaviors to lower food waste, yet implement practices that ultimately contribute to higher levels of food waste elsewhere in the supply chain. Through interviews with key actors in the Australian fresh fruit and vegetable supply chain, we highlight the existence of a legitimacy gap in corporate social responsibility whereby undesirable behaviors are pushed elsewhere in the supply chain. It is argued that the structural power held by Australia’s retail duopoly means that supermarkets are able to claim virtuous and responsible behaviors, despite counter claims from within the fresh food industry that the food supermarkets’ private quality standards mean that fresh food is wasted. We argue that the supermarkets claim CSR kudos for reducing food waste at the expense of other supply chain actors who bear both the economic cost and the moral burden of waste, and that this is a consequence of supermarkets’ remarkable market power in Australia.

Photoswitchable multivalent sugar ligands: Synthesis, isomerization, and lectin binding studies of azobenzene-glycopyranoside derivatives

Coating of azobenzene chromophore with multivalent sugar ligands has been accomplished. Such sugar coating allows the study of the isomerization properties of this chromophore in aqueous solutions. The predominantly cis-isomer-containing photostationary state (PS) mixture of these azobenzene derivatives is found to be stable for hours. The rate constants for their isomerization, as well as the Arrhenius activation energies, are determined experimentally. An assessment of the lectin binding properties of the lactoside bearing isomeric azobenzene derivatives, by isothermal calorimetric methods, reveals the existence of an unusual cooperativity in their binding to lectin peanut agglutinin. Thermodynamic parameters evaluated for the trans and the PS mixture are discussed, in detail, for the lactoside bearing bivalent azobenzene derivative.

Ultrastructure of Biofilms Formed by Bacteria from Industrial Processes

Microorganisms exist predominantly as sessile multispecies communities in natural habitats. Most bacterial species can form these matrix-enclosed microbial communities called biofilms. Biofilms occur in a wide range of environments, on every surface with sufficient moisture and nutrients, also on surfaces in industrial settings and engineered water systems. This unwanted biofilm formation on equipment surfaces is called biofouling. Biofouling can significantly decrease equipment performance and lifetime and cause contamination and impaired quality of the industrial product. In this thesis we studied bacterial adherence to abiotic surfaces by using coupons of stainless steel coated or not coated with fluoropolymer or diamond like carbon (DLC). As model organisms we used bacterial isolates from paper machines (Meiothermus silvanus, Pseudoxanthomonas taiwanensis and Deinococcus geothermalis) and also well characterised species isolated from medical implants (Staphylococcus epidermidis). We found that coating of steel surface with these materials reduced its tendency towards biofouling: Fluoropolymer and DLC coatings repelled all four biofilm formers on steel. We found great differences between bacterial species in their preference of surfaces to adhere as well as their ultrastructural details, like number and thickness of adhesion organelles they expressed. These details responded differently towards the different surfaces they adhered to. We further found that biofilms of D. geothermalis formed on titanium dioxide coated coupons of glass, steel and titanium, were effectively removed by photocatalytic action in response to irradiation at 360 nm. However, on non-coated glass or steel surfaces irradiation had no detectable effect on the amount of bacterial biomass. We showed that the adhesion organelles of bacteria on illuminated TiO2 coated coupons were complety destroyed whereas on non-coated coupons they looked intact when observed by microscope. Stainless steel is the most widely used material for industrial process equipments and surfaces. The results in this thesis showed that stainless steel is prone to biofouling by phylogenetically distant bacterial species and that coating of the steel may offer a tool for reduced biofouling of industrial equipment. Photocatalysis, on the other hand, is a potential technique for biofilm removal from surfaces in locations where high level of hygiene is required. Our study of natural biofilms on barley kernel surfaces showed that also there the microbes possessed adhesion organelles visible with electronmicroscope both before and after steeping. The microbial community of dry barley kernels turned into a dense biofilm covered with slimy extracellular polymeric substance (EPS) in the kernels after steeping in water. Steeping is the first step in malting. We also presented evidence showing that certain strains of Lactobacillus plantarum and Wickerhamomyces anomalus, when used as starter cultures in the steeping water, could enter the barley kernel and colonise the tissues of the barley kernel. By use of a starter culture it was possible to reduce the extensive production of EPS, which resulted in a faster filtration of the mash.

Tablettien soveltuvuus annosjakeluun

Koneellinen annosjakelu on kasvava lääkehuollon osa-alue, jossa lääkkeet pakataan koneellisesti pieniin annoskertakohtaisiin pusseihin kahden viikon erissä. Aikaisemmin lääkevalmisteiden soveltuvuutta koneelliseen annosjakeluun ei ole systemaattisesti tutkittu. Tutkimus tehtiin yhteistyössä Espoonlahden apteekin annosjakeluyksikön kanssa ja sen tavoitteena oli määrittää annosjakeluprosessin kannalta optimaaliset ominaisuudet annosjaeltavalle tabletille rikkoutumisten ja siirtymien vähentämiseksi. Rikkoutuminen on lääkevalmisteen murentumista, puolittumista tai muuta rikkoutumista annosjakelun aikana. Siirtymä on lääkevalmisteen jakelu väärään annospussiin. Prosentuaalisesti rikkoutumisia ja siirtymiä on jakelumäärästä hyvin vähän, mutta määrällisesti paljon ja koko ajan enemmän koneellisen annosjakelun yleistyessä. Rikkoutumiset ja siirtymät aiheuttavat paljon lisätyötä pussien korjaamisen takia, joten niiden määrää on pyrittävä vähentämään. Lisäksi tavoitteena oli selvittää lääkkeiden valmistajilta kysyttävissä olevat asiat lääkevalmisteiden ominaisuuksista ja säilyvyydestä, jotta voitaisiin päätellä valmisteen soveltuvuus koneelliseen annosjakeluun kirjallisen tiedon perusteella. Tutkimuksen tulosten perusteella rikkoutumisten ja siirtymien vähentämiseksi optimaalinen tablettivalmiste annosjakeluun on pienehkö tai keskisuuri, päällystetty, luja ja jakouurteeton ja optimaalinen ilman suhteellinen kosteustaso annosjakeluyksikön tuotantotiloissa olisi noin 30 – 40 %. Lääkkeiden valmistajilta kysyttäviä seikkoja ovat koon, päällysteen, murtolujuuden ja jakouurteen lisäksi valmisteen säilyvyys alkuperäispakkauksen ulkopuolella sekä valmisteen valo-, lämpö- ja kosteusherkkyys. Rikkoutumisten ja siirtymien lisäksi tutkittiin myös kosteusherkän asetyylisalisyylihappovalmisteen (Disperin 100 mg) säilyvyyttä 25 °C ja 60 % RH olosuhteissa, koska tuotantotilojen ilman kosteustasoa ei ole säädelty. Säilyvyystutkimuksen kesto oli neljä viikkoa. Se on riittävä, koska se on enimmäisaika, jonka tabletit ovat annosjakeluprosessin yhteydessä pois alkuperäispakkauksestaan ennen käyttöä. Tabletteja säilytettiin avoimessa alkuperäispakkauksessa (purkki), suljetussa alkuperäispakkauksessa, annosjakelukoneen kasetissa ja kahdessa erilaisessa annospussissa (uusi ja käytössä oleva materiaali). Tulosten mukaan annosjakelukoneen kasetti suojaa kosteudelta yhtä huonosti kuin avoin purkki. Uusi pussimateriaali sen sijaan suojaa kosteudelta paremmin kuin tällä hetkellä käytössä oleva materiaali. Raman -spektroskopiamittausten perusteella asetyylisalisyylihappotableteissa ei ehdi neljän viikon seurannan aikana tapahtua asetyylisalisyylihapon hajoamista salisyylihapoksi. Kosteus heikentää tablettien murtolujuutta, mikä saattaa aiheuttaa enemmän rikkoutumisia. Kosteustaso olisi hyvä olla säädettävissä vakioksi tuotantotiloissa tai purkaa tabletit kasetteihin mahdollisimman lähellä jakelua rikkoutumisten ehkäisemiseksi, etenkin ilman kosteustason ollessa korkea. Lisäksi tutkittiin lääkevalmisteen lämpöherkkyyttä koska annosjakelukoneen saumauslaite altistaa annospussit noin 75 °C lämmölle, jos annosjakelukone pysäytetään kesken työn. Tutkimus tehtiin XRPD:llä, jolla voidaan säätää näytteen lämpötilaa. Lämpöherkkyystutkimusten perusteella 75 °C lämpö ei ehdi tunnin aikana aiheuttaa muutoksia karbamatsepiinitabletissa (Neurotol 200 mg). Tuloksista selvisi, että tutkitun valmisteen sisältämä karbamatsepiini ei kuitenkaan ole lämpöherkin muoto, joten muita lämpöherkkiä lääkevalmisteita tulisi tutkia lisätiedon saamiseksi lämmön vaikutuksista.

Deposition of ZnO Films by Combustion Flame Pyrolysis of Solution Precursors

The structural features,including preferred orientation and surface morphology of zinc oxide (ZnO) films deposited by combustion flame pyrolysis were investigated as a function of process parameters, which include precursor solution concentration, substrate-nozzle (S-N) distance, gas flow rate, and duration of deposition. In this technique, the precursor droplets react within the flame and form a coating on an amorphous silica substrate held in or near the flame. Depending on the process parameters, the state of decomposition at which the precursor arrives on the substrate varies substantially and this in turn dictates the orientation and microstructure of the films.

Effect of Nanostructuring and Ex situ Amorphous Carbon Coverage on the Lithium Storage and Insertion Kinetics in Anatase Titania

Implications of nanostructuring and conductive carbon interface on lithium insertion/removal capacity and insertion kinetics innanoparticles of anatase polymorph of titania is discussed here.Sol-gel synthesized nanoparticles of titania (particle size similar to 6 nm) were hydrothermally coated ex situ with a thin layer of amorphous carbon (layer thickness: 2-5 nm) and calcined at a temperature much higher than the sol-gel synthesis temperature. The carbon-titania composite particles (resulting size similar to 10 nm) displayed immensely superior cyclability and rate capability (higher current rates similar to 4 g(-1)) compared to unmodified calcined anatase titania. The conductive carbon interface around titania nanocrystal enhances the electronic conductivity and inhibits crystallite growth during electrochemical insertion/removal thus preventing detrimental kinetic effects observed in case of unmodified anatase titania. The carbon coating of the nanoparticles also stabilized the titania crystallographic structure via reduction in the accessibility of lithium ions to the trapping sites. This resulted in a decrease in the irreversible capacity observed in the case of nanoparticles without any carbon coating.

A low-cost lead-acid battery with high specific-energy

Lightweight grids for lead-acid battery grids have been prepared from acrylonitrile. butadiene styrene (ABS) copolymer followed by coating with lead. Subsequently, the grids have been electrochemically coated with a conductive and corrosion-resistant layer of polyaniline. These grids are about 75% lighter than those employed in conventional lead-acid batteries. Commercial-grade 6V/3.5 Ah (C-20-rate) lead-acid batteries have been assembled and characterized employing positive and negative plates constituting these grids. The specific energy of such a lead-acid battery is about 50 Wh/kg. The batteries can withstand fast charge-discharge duty cycles.

Microwave irradiation-assisted method for the deposition of adherent oxide films on semiconducting and dielectric substrates

We report a method for the deposition of thin films and thick coatings of metal oxides through the liquid medium, involving the micro waveirradiation of a solution of a metal-organic complex in a suitable dielectric solvent. The process is a combination of sol-gel and dip-coating methods, wherein coatings can be obtained on nonconducting and semiconducting substrates, within a few minutes. Thin films of nanostructured ZnO (wurtzite) have been obtained on Si(100), glass and polymer substrates, the nanostructure determined by process parameters The coatings are strongly adherent and uniform over 15 mm x 15 mm, the growth rate similar to 0.25 mu m/min Coatings of nanocrystalline Fe2O3 and Ga2O3 have also been obtained The method is scalable to larger substrates, and is promising as a low temperature technique for coating dielectric substrates, including flexible polymers. (C) 2010 Elsevier B.V. All rights reserved.

Laser Surface Alloying of a Creep Resistant Magnesium Alloy MRI 230D with Al and Al2O3

A creep resistant permanent mould cast Mg alloy MRI 230D was laser surface alloyed with Al and a mixture of Al and Al2O3 using pulsed Nd:YAG laser irradiation at four different scan speeds in order to improve the corrosion and wear resistance. The microstructure, corrosion and wear behavior of the laser surface alloyed material is reported in this manuscript. The coating comprised of a featureless microstructure with cellular-dendritic microstructure near the interface and exhibited good interfacial bonding. A few solidification cracks reaching down to substrate were also observed. The two step coating with Al followed by a mixture of Al and Al2O3 exhibited a slightly better corrosion resistance than the single step coating with Al. In the long run, however, corrosion resistance of both the coatings became comparable to the as-cast alloy. The corroded surface of the laser surface alloyed specimens revealed a highly localized corrosion. The laser surface alloyed specimens exhibited an improvement in wear resistance. The laser scan speed did not exhibit a monotonic trend either in corrosion or wear resistance.

Functional Surfaces for Microfluidics in Proteomic Analysis

Microchips for use in biomolecular analysis show a lot of promise for medical diagnostics and biomedical basic research. Among the potential advantages are more sensitive and faster analyses as well as reduced cost and sample consumption. Due to scaling laws, the surface are to volume ratios of microfluidic chips is very high. Because of this, tailoring the surface properties and surface functionalization are very important technical issues for microchip development. This thesis studies two different types of functional surfaces, surfaces for open surface capillary microfluidics and surfaces for surface assisted laser desorption ionization mass spectrometry, and combinations thereof. Open surface capillary microfluidics can be used to transport and control liquid samples on easily accessible open surfaces simply based on surface forces, without any connections to pumps or electrical power sources. Capillary filling of open partially wetting grooves is shown to be possible with certain geometries, aspect ratios and contact angles, and a theoretical model is developed to identify complete channel filling domains, as well as partial filling domains. On the other hand, partially wetting surfaces with triangular microstructures can be used for achieving directional wetting, where the water droplets do not spread isotropically, but instead only spread to a predetermined sector. Furthermore, by patterning completely wetting and superhydrophobic areas on the same surface, complex droplet shapes are achieved, as the water stretches to make contact with the wetting surface, but does not enter into the superhydrophobic domains. Surfaces for surface assisted laser desorption ionization mass spectrometry are developed by applying various active thin film coatings on multiple substrates, in order to separate surface and bulk effects. Clear differences are observed between both surface and substrate layers. The best performance surfaces consisted of amorphous silicon coating and an inorganic-organic hybrid substrate, with nanopillars and nanopores. These surfaces are used for matrix-free ionization of drugs, peptides and proteins, and for some analytes, the detection limits were in the high attomoles. Microfluidics and laser desorption ionization surfaces are combined on a functionalized drying platforms, where the surface is used to control the shape of the deposited analyte droplet, and the shape of the initial analyte droplet affects the dried droplet solute deposition pattern. The deposited droplets can then directly detected by mass spectrometry. Utilizing this approach, results of analyte concentration, splitting and separation are demonstrated.

Ruokauskomukset Mosambikin maaseudun raskaana olevilla ja imettävillä naisilla

Ihmisille ympäri maailmaa on tyypillistä valita tiettyjä ruokia suuremmasta valikoimasta syömäkelpoista ruokaa ja luoda mieltymyksiä sekä kieltoja joitakin ruokia kohtaan. Näitä ilmiöitä kutsutaan ruokauskomuksiksi ja ne ovat tärkeä osa kulttuuria. Niiden taustalla on usein terveydelliset perustelut tai sosiaalinen arvostus yhteisössä. Afrikassa on todettu olevan paljon erilaisia ruokauskomuksia, jotka kohdistuvat usein raskaana oleviin ja imettäviin naisiin sekä lapsiin, ryhmään, joka on fysiologisesti erityisen herkässä elämänvaiheessa. Ravitsemustilan tai ruokaturvan ollessa heikko, mahdollisilla ruokauskomuksilla voi olla merkittävät seuraukset erityisesti tämän väestönosan terveydentilaan. Aliravitsemus ja virheravitsemus ovat edelleen suuria ongelmia Afrikassa ja muissa kehittyvissä maissa. Tämän työn tavoitteena oli tutkia laadullisin menetelmin, onko erityisesti raskaana olevilla ja imettävillä naisilla Keski-Mosambikin maaseudulla, Zambézian maakunnassa, ruokauskomuksia, mitä ne mahdollisesti ovat, sekä arvioida voiko ruokauskomuksilla olla ravitsemuksellista merkitystä. Menetelminä oli 5 ryhmähaastattelua kolmessa kylässä ja 10 yksilöhaastattelua kahdessa kylässä. Tutkittavat olivat 12–78-vuotiaita naisia ja heitä oli yhteensä 27. Tulkkaus, tutkimusaiheen sensitiivisyys ja haastattelijan kokemattomuus aiheuttivat haasteita haastatteluiden toteutukseen. Tämän vuoksi menetelmää muokattiin ja se vaihdettiin ryhmähaastattelusta yksilöhaastatteluun tutkimuksen aikana. Ruokauskomukset vaihtelivat sekä kylien välillä että kylien sisällä, joskin niistä löytyi samantyyppisiä pääpiirteitä. Työssä todettiin, että raskaana oleviin ja imettäviin naisiin kohdistui tutkimusalueella ruokauskomuksia. Raskauden aikana tuli välttää pääasiassa proteiinipitoisia ruokia, kuten lihaa ja kalaa ja puolestaan suosia kasvisten, hedelmien ja viljatuotteiden käyttöä. Linnun munien syöntiä sekä suositeltiin että kehotettiin välttämään raskauden aikana. Raskauden aikana ilmeni lisäksi tietoinen tapa vähentää kassavapuuron tai ruuan syömistä kokonaisuudessaan. Imetyksen aikana ei vältetty juuri mitään ruokia, vaan suositeltiin kookosta ja kasviksia. Suurin osa perusteluista liittyi äidin ja lapsen terveyteen. Perustelut voitiin jakaa seuraaviin ryhmiin: lisää äidinmaidon tuotantoa; aiheuttaa vatsakipua äidillä; pitää yllä kuntoa ja estää vatsan kasvua; äidistä tulee vahva, terve ja hän saa vitamiineja; lapsen ulkonäkö muuttuu; lapsesta tulee terve ja vahva; lapsen käyttäytyminen muuttuu; aiheuttaa keskenmenon; aiheuttaa vaikean tai helpon synnytyksen. Ruokauskomukset ja terveysviranomaisilta tullut valistus oli osittain sekoittunut keskenään. Lähes kaikki naiset kertoivat noudattavansa näitä ruokauskomuksia. Muutamat naiset kertoivat suositeltavien ruokien kohdalla, että ruokien saatavuus tekee noudattamisen joskus vaikeaksi. Proteiinipitoisten ruokien välttäminen voi lisätä proteiinialiravitsemuksen riskiä ja syömisen vähentäminen saattaa lisätä riskiä saada riittämättömästi energiaa raskauden aikana. Suositeltavat ruuat todennäköisesti edistävät terveyttä. Tutkielman perusteella voitiin todeta, että vieraassa kulttuurissa tutkiminen vaatii tutkimusmenetelmältä paljon. Tärkeää on menetelmän joustavuus, jotta sitä voi muuttaa tutkimuskentällä toimivampaan ja luotettavampaan muotoon. Johtopäätöksenä todettiin, että suositeltavin menetelmä tutkittaessa ruokauskomuksia tällä tutkimusalueella olisi ollut yksilöhaastattelut, jossa olisi ollut mahdollisimman vähän osallistujia ja osallistujat olisivat olleet samaa sukupuolta ja saman ikäisiä. Terveyden ja ravitsemuksen kannalta on tärkeää, että ruokauskomuksista ollaan tietoisia ja väestön ruokauskomuksia tutkitaan alueittain, koska ne voivat vaihdella merkittävästi jopa kylien tai ihmisryhmien sisällä.

Dielectric properties of poly(vinylidene luoride)/CaCu3Ti4O12 nanocrystal composite thick films

The poly(vinylidene fluoride)/CaCu3Ti4O12 (CCTO) nanocrystal composite films (thickness approximate to 85 mu m) with relatively high dielectric permittivity (90 at 100 Hz) were prepared by the solution casting followed by spin coating technique. The structural, the microstructural and the dielectric properties of the composites were studied using X-ray diffraction, Scanning Electron Microscope, and Impedance analyzer respectively. The effective dielectric permittivity (e(eff)) of the composite increased with increase in the volume fraction of CCTO at all the frequencies (100 Hz to 1 MHz) under investigation. The room temperature dielectric permittivity which is around 90 at 100 Hz, has increased to about 290 at 125 degrees C (100 Hz). These results may be exploited in the development of high energy density capacitors.

Effect of sintering on optical, structural and photoluminescence properties of ZnO thin films prepared by sol-gel process

Zinc oxide (ZnO) thin films have been deposited on glass substrates via sol-gel technique using zinc acetate dihydrate as precursor by spin coating of the sol at 2000 rpm. Effects of annealing temperature on optical, structural and photo luminescence properties of the deposited ZnO films have been investigated. The phase transition from amorphous to polycrystalline hexagonal wurtzite structure was observed at an annealing temperature of 400 degrees C. An average transmittance of 87% in the visible region has been obtained at room temperature. The optical transmittance has slightly increased with increase of annealing temperature. The band gap energy was estimated by Tauc's method and found to be 3.22 eV at room temperature. The optical band gap energy has decreased with increasing annealing temperature. The photoluminescence (PL) intensity increased with annealing temperature up to 200 degrees C and decreased at 300 degrees C. (c) 2010 Elsevier B.V. All rights reserved.