Desenvolvimento de pastas cimentantes utilizando cimentos portland compostos para cimentação de poços petrolíferos

The Compound Portland cements are commonly used in construction, among them stand out the CPII-Z, CPII-F and CPIV. These types of cement have limited application on oil well cementing, having its compositional characteristics focused specifically to construction, as cement for use in oil wells has greater complexity and properties covering the specific needs for each well to be coated. For operations of oil wells cementing are used Portland cements designed specifically for this purpose. The American Petroleum Institute (API) classifies cements into classes designated by letters A to J. In the petroleum industry, often it is used Class G cement, which is cement that meets all requirements needed for cement from classes A to E. According to the scenario described above, this paper aims to present a credible alternative to apply the compound cements in the oil industry due to the large availability of this cement in relation to oil well cements. The cements were micro structurally characterized by XRF, XRD and SEM tests, both in its anhydrous and hydrated state. Later technological tests were conducted to determine the limits set by the NBR 9831. Among the compound cements studied, the CPII-Z showed satisfactory properties for use in primary and secondary operations of oil wells up to 1200 meters cementing

Formulação e caracterização de pastas espumadas por incorporação de ar e estabilizantes minerais

Cementing operations may occur at various stages of the life cycle of an oil well since its construction until its definitive abandonment. There are some situations in which the interest zones are depleted or have low fracture pressure. In such cases, the adoption of lowdensity cement slurries is an efficient solution. To this end, there are basically three ways to reduce the density of cement slurries: using microspheres, water extending additives or foamed cement. The objective of this study is to formulate, to study and to characterize lowdensity foamed cement, using an air entrainment surfactant with vermiculite or diatomite as water extenders and stabilizers. The methodology consists on preparation and evaluation of the slurries under the American Petroleum Institute (API) and the Brazilian Association of Technical Standards (ABNT) guidelines. Based on calculated densities between 13 and 15 ppg (1.559 and 1.799 g/cm3), the slurries were prepared with fixed surfactant concentration, varying the concentrations of vermiculite and diatomite and were compared with the base slurries. The results of plastic viscosity, yield point and gel strength and the compressive strength for 24 h showed that the slurries presented suitable rheology and mechanical strength for cementing operations in oil wells, and had their densities reduced between 8.40 and 11.89 ppg (1.007 and 1.426 g/cm3). The conclusion is that is possible, under atmospheric conditions, to obtain light weighted foamed cement slurries with satisfactory rheological and mechanical properties by means of air entrainment and mineral additions with extenders and stabilizers effects. The slurries have great potential for cementing operations; applicability in deep wells, in low fracture gradient formations and in depleted zones and bring cost savings by reducing the cementing consumption

Reforma a seco de metano com catalisadores Ni/MCM-41 sintetizados a partir de fontes alternativas de sílica

The production of synthesis gas has received renewed attention due to demand for renewable energies to reduce the emissions of gases responsible for enhanced greenhouse effect. This work was carried out in order to synthesize, characterize and evaluate the implementation of nickel catalysts on MCM-41 in dry reforming reactions of methane. The mesoporous molecular sieves were synthesized using as silica sources the tetraethyl orthosilicate (TEOS) and residual glass powder (PV). The sieves were impregnated with 10% nickel to obtain the metallic catalysts (Ni/MCM-41). These materials were calcined and characterized by Thermogravimetric Analysis (TG), Infrared spectroscopy (FTIR), X-ray Diffraction (XRD), Temperature-Programmed Reduction (TPR) and N2 Adsorption/Desorption isotherms (BET/BJH). The catalytic properties of the samples were evaluated in methane dry reforming with CO2 in order to produce synthesis gas to be used in the petrochemical industry. The materials characterized showed hexagonal structure characteristic of mesoporous material MCM-41 type, being maintained after impregnation with nickel. The samples presented variations in the specific surface area, average volume and diameter of pores based on the type of interaction between the nickel and the mesoporous support. The result of the the catalytic tests showed conversions about 91% CO2, 86% CH4, yelds about 85% CO and 81% H2 to Ni/MCM-41_TEOS_C, and conversions about 87% CO2, 82% CH4, yelds about 70% CO and 59% H2 to Ni/MCM-41_PV_C. The similar performance confirms that the TEOS can be replaced by a less noble materials

Síntese e caracterização do líquido iônico tetrafluoroborato de 1-metil-3-(2,6-(S)-dimetiloct-2-eno)-imidazol como eletrólito para produção de hidrogênio via eletrólise da água

Ionic liquids (ILs) are organic compounds liquid at room temperature, good electrical conductors, with the potential to form as a means for electrolyte on electrolysis of water, in which the electrodes would not be subjected to such extreme conditions demanding chemistry [1]. This paper describes the synthesis, characterization and study of the feasibility of ionic liquid ionic liquid 1-methyl-3(2,6-(S)-dimethyloct-2-ene)-imidazole tetrafluoroborate (MDI-BF4) as electrolyte to produce hydrogen through electrolysis of water. The MDI-BF4 synthesized was characterized by thermal methods of analysis (Thermogravimetric Analysis - TG and Differential Scanning Calorimetry - DSC), mid-infrared spectroscopy with Fourier transform by method of attenuated total reflectance (FTIR-ATR), nuclear magnetic resonance spectroscopy of hydrogen (NMR 1H) and cyclic voltammetry (CV). Where thermal methods were used to calculate the yield of the synthesis of MDI-BF4 which was 88.84%, characterized infrared spectroscopy functional groups of the compound and the binding B-F 1053 cm-1; the NMR 1H analyzed and compared with literature data defines the structure of MDI-BF4 and the current density achieved by MDI-BF4 in the voltammogram shows that the LI can conduct electrical current indicating that the MDI-BF4 is a good electrolyte, and that their behavior does not change with the increasing concentration of water

Estudo da formulação de pré-misturas secas para a cimentação de poços em terra

An economical solution for cementing oil wells is the use of pre-prepared dry mixtures containing cement and additives. The mixtures may be formulated, prepared and transported to the well where is added water to be pumped.Using this method, becomes dispensable to prepare the cement mixes containing additives in the cementing operation, reducing the possibility of error. In this way, the aim of this work is to study formulations of cement slurries containing solid additives for primary cementing of oil wells onshore for typical depths of 400, 800 and 1,200 meters. The formulations are comprised of Special Class Portland cement, mineral additions and solids chemical additives.The formulated mixtures have density of 1.67 g / cm ³ (14.0 lb / gal). Their optimization were made through the analysis of the rheological parameters, fluid loss results, free water, thickening time, stability test and mechanical properties.The results showed that mixtures are in conformity the specifications for cementing oil wells onshore studied depths

Obtenção de álcool alílico (PROP-2-EN-1-OL) a partir da glicerina derivada do biodiesel de óleo de mamona

In this work, biodiesel was produced from castor oil that was a byproduct glycerin. The molar ratio between oil and alcohol, as well as the use of (KOH) catalyst to provide the chemical reaction is based on literature. The best results were obtained using 1 mol of castor oil (260g) to 3 moles of methyl alcohol (138g), using 1.0% KOH as catalyst at a temperature of 260 ° C and shaken at 120 rpm. The oil used was commercially available, the process involves the reaction of transesterification of a vegetable oil with methyl alcohol. The product of this reaction is an ester, biodiesel being the main product and the glycerin by-product which has undergone treatment for use as raw material for the production of allyl alcohol. The great advantage of the use of glycerin to obtain allyl alcohol is that its use eliminates the large amount of waste of the biodiesel and various forms of insult to the environment. The reactions for the formation of allyl alcohol was conducted from formic acid and glycerin in a ratio 1/1, at a temperature of 260oC in a heater blanket, being sprayed by a spiral condenser for a period of 2 hours and the product obtained contains mostly the allylic alcohol .. The monitoring of reactions was performed by UV-Visible Spectrophotometer: FTIR Fourier transform, the analysis showed that these changes occur spectrometer indicating the formation of the product allylic alcohol (prop-2-en-1-ol) in the presence of water, This alcohol was appointed Alcohol GL. The absorption bands confirms that the reaction was observed in (υ C = C) 1470 -1600 cm -1 and (υ CO), 3610-3670 attributed to C = C groups and OH respectively. The thermal analysis was carried out in a thermogravimetric analyzer SDT Q600, where the mass and temperature are displayed against time, that allows checking the approximate rate of heating. The innovative methodology developed in the laboratory (LABTAM, UFRN), was able to treat the glycerine produced by transesterification of castor oil and used as raw material for production of allyl alcohol, with a yield of 80%, of alcohol, the same is of great importance in the manufacture of polymers, pharmaceuticals, organic compounds, herbicides, pesticides and other chemicals

Pirólise rápida catalítica do capim elefante utilizando materiais mesoporosos e óxidos metálicos para deoxigenação em bio-óleo

The fast pyrolysis of lignocellulosic biomass is a thermochemical conversion process for production energy which have been very atratactive due to energetic use of its products: gas (CO, CO2, H2, CH4, etc.), liquid (bio-oil) and charcoal. The bio-oil is the main product of fast pyrolysis, and its final composition and characteristics is intrinsically related to quality of biomass (ash disposal, moisture, content of cellulose, hemicellulose and lignin) and efficiency removal of oxygen compounds that cause undesirable features such as increased viscosity, instability, corrosiveness and low calorific value. The oxygenates are originated in the conventional process of biomass pyrolysis, where the use of solid catalysts allows minimization of these products by improving the bio-oil quality. The present study aims to evaluate the products of catalytic pyrolysis of elephant grass (Pennisetum purpureum Schum) using solid catalysts as tungsten oxides, supported or not in mesoporous materials like MCM-41, derived silica from rice husk ash, aimed to reduce oxygenates produced in pyrolysis. The biomasss treatment by washing with heated water (CEL) or washing with acid solution (CELix) and application of tungsten catalysts on vapors from the pyrolysis process was designed to improve the pyrolysis products quality. Conventional and catalytic pyrolysis of biomass was performed in a micro-pyrolyzer, Py-5200, coupled to GC/MS. The synthesized catalysts were characterized by X ray diffraction, infrared spectroscopy, X ray fluorescence, temperature programmed reduction and thermogravimetric analysis. Kinetic studies applying the Flynn and Wall model were performed in order to evaluate the apparent activation energy of holoceluloce thermal decomposition on samples elephant grass (CE, CEL and CELix). The results show the effectiveness of the treatment process, reducing the ash content, and were also observed decrease in the apparent activation energy of these samples. The catalytic pyrolysis process converted most of the oxygenate componds in aromatics such as benzene, toluene, ethylbenzene, etc

Host specificity of a Brazilian isolate of Alternaria cassiae (Cenargen CG593) under greenhouse conditions

Several Alternaria cassiae isolates were recovered from diseased sicklepod plants (Senna obtusifolia) in the southern regions of Brazil. A representative isolate (Cenargen CG593) was tested for its host range under greenhouse conditions. The fungus promoted symptoms in sicklepod, cassava (Manihot dulce), tomato (Lycopersicon esculentum) and eggplant (Solanum melongena) when tested at a spore concentration of 10(6) spores ml(-1). When the plants were inoculated with a suspension of 10(5) spores ml(-1) and held at a dew period of 12 h (cassava) or 18 h (tomato and eggplant), the plants showed symptoms of the disease, but they recovered and continued their normal vegetative growth. These results show that the fungus A. cassiae is safe to use for the control of S. obtusifolia under Brazilian conditions, because it did not cause excessive damage in the three plants tested.

Caracterização molecular e laboratorial da talassemia beta e da interação hemoglobina s/talassemia beta

Beta thalassemia arises as a consequence of the reduction (β+, β++, βsilent) or absence (β0) of beta globin chain synthesis and results from a number of mechanisms that lead to genetic defects. The inheritance of beta thalassemia is characterized by the existence of heterozygous individuals, compound heterozygotes, homozygotes and those with coinheritance of beta thalassemia allele and other thalassemias and/or hemoglobin variants. The aim of this study was to perform molecular and laboratory characterization of beta thalassemia in heterozygous and homozygous individuals and in those with coinheritance of S beta thalassemia. A total of 48 individuals were included (35 heterozygotes, 4 homozygotes and 9 S beta thalessemia carriers) referred to the Integrated Laboratory of Clinical Analyses of the Federal University of Rio Grande do Norte (UFRN) and the Hematology Ambulatory Facility of the Dalton Barbosa Cunha Hemocenter (Hemonorte Natal, Brazil). Peripheral blood samples form each patient underwent the following laboratory examinations: erythrogram, hemoglobin electrophoresis at alkaline pH, measurements of Hb A2, Fetal Hb and serum ferritin. DNA was extracted using the illustra blood genomicPrep Mini Spin Kit and molecular characterization was performed by the PCR/RFLP technique, which involves digestion with specific restriction enzymes for IVS-1 nt 1 (G®A), IVS-1 nt 6 (T®C) and codon 39 (CAG®TAG) mutations. Of the 35 heterozygotes, 37.1% showed IVS-1 nt 6 mutation, 42.9% IVS-1 nt 1 and 20% were carriers of other mutations not identified by the technique used. The four homozygous patients presented with the IVS-1 nt 6 mutation, while 66.7% of the individuals with S beta thalassemia had the IVS-1 nt 1 mutation. Codon 39 was not detected in any of the patients investigated. Of the thallasemic alleles found, 40.4% were IVS- 1 nt 1, 40.4% IVS-1 nt 6 and 19.2% were not identified. Laboratory data showed that the heterozygotes exhibited microcytosis and hypochromia, evidenced by MCV ranging from 57 to 75fL and MCH from 15.9 to 23.6 pg. Hemoglobin A2 varied between 3.7 and 7.2%. The homogygotes also showed reduced MCV and MCH and elevated HbA2.. Comparison of laboratory data between heterozygous individuals with IVS-1 nt 1 and IVS-1 nt 6 mutations showed that heterozygotes for the IVS1-1 mutation had significantly lower mean MCV and MCH (p = 0.023 and 0.007, respectively) and significantly higher hemoglobin A2 (p < 0.001) when compared to heterozygotes for the IVS-1 nt 6 mutation. PCR/RFLP was useful in identifying the presence or absence of IVS-1 nt 6, IVS-1 nt 1 and codon 39 mutations in most of the patients investigated here. This is the first study conducted in the state of Rio Grande do Norte, Brazil aimed at identifying beta thalassemia mutations and represents an important contribution to the knowledge regarding the molecular profile of beta thalassemia in our country

Investigação das alterações citogenéticas em pacientes pediátricos com leucemia linfóide aguda do Rio Grande do Norte

Leukemia is a heterogeneous group of hematologic malignancies that result from partial or total transformation of the blast cells. The Acute Lymphoblastic Leukemia (ALL) is the most common malignancy in childhood, especially in male, Caucasian children younger than 14 years. Several criteria are adopted to classify ALL, including the cell morphology, cytochemistry, immunophenotyping and cytogenetic analysis. Cytogenetic studies allow a more detailed analysis to detect chromosomal abnormalities of leukemic cells. These modifications will determine the diagnosis, classification, stage characterization, remission assessment and prognosis. In this study were evaluated 30 patients, aged from four months to seventeen years, of both sexes and various ethnicities. The age distribution showed that 67% of patients had between one and ten years (with mean age of XX years old), the most prevalent ethnic was Caucasian (50%) and 57% were males. According to immunophenotype, 93% of patients had B-cells progenitor ALL and 7% early lineage T. Considering the total studied population, the most frequent medical findings were lymphadenopathy (37%), hepatomegaly (77%) and splenomegaly (70%), where one patient could present more than one of these medical findings. Regarding the CBC, the majority of patients had hemoglobin below 10 g / dl (73%), leukocyte count less than 10.000/μL (60%) and platelet count below 150.000/μL (83%). Chromosomal abnormalities were observed in 64% of all patients, where hyperdiploidy was the most common numerical change (67%), followed by hypodiploid (33%). All these data are in agreement with the literature. Moreover, complexes structural and/or number changes not yet described in literature were observed, which indicated poor prognosis. Finally, we concluded that this study demonstrated the importance of cytogenetic study in the diagnosis and identification of prognostic factors in pediatric patients with ALL in Rio Grande do Norte. The results obtained in this study are extremely useful and emphasizes that surveys of this nature must be conducted more frequently in our state

Avaliação de efeitos toxicológicos e comportamentais de ginseng panax em ratos

Panax ginseng CA Meyer (Araliaceae) is a herbaceous plant widely used in China, South Korea, Japan and other Asian countries for the treatment of various diseases micro circulatory, cerebrovascular, among others, representing one of the drugs used by older man. It has over 30 biologically active ginsenosides with different pharmacological and behavioral effects and inhibitory effect on the NMDA receptor. The amino acid glycine is a co-agonist of the NMDA receptor, activating this receptor. At the cellular level, ketamine is widely known to be NMDA receptor antagonist. The aim of this study was to evaluate the general activity in the open field, and anxiety in elevated plus maze, mice treated with P. ginseng compared with the action of ketamine and glycine, to better understand the action of this herbal medicine at the NMDA receptor. We used 66 adult male rats were divided into six groups: a positive control, treated for 30 days with water by gavage, who received glycine (500mg/kg; po) on days 7, 14, 21 and 28 of treatment, one hour before of behavioral assessment, a negative control was treated for 30 days with water by gavage received ketamine (5mg/kg, ip) on days 7, 14, 21 and 28 of treatment, one hour prior to behavioral evaluation, three experimental groups, receiving 100, 200 or 300 mg / kg P. ginseng by gavage for 30 days and one group treated solely with white water, and is also administered 1 ml of water by gavage one hour prior to behavioral evaluation. Animal behavior in these three groups was also examined on days 7, 14, 21 and 28 of treatment. On day 30 of treatment, the animals were anesthetized with thiopental (70mg/kg) for blood collection and after euthanasia, withdrawal of various organs. There were no changes in weight and body weight gain and weight reasons in organ / body weight. However the consumption of water and food values showed a significant increase. Serum levels of AST was increased in a dose-dependently in the animals treated with doses of P. ginseng, glycine and ketamine as compared to the blank group. Unlike creatinine levels proved to be decreased in all treated groups when compared with white. However, the level of urea in these groups was reduced and no changes were observed in the ALT parameter. Histopathological examination revealed no changes in cell morphology in different tissues. There were no behavioral changes in the elevated plus maze and few changes were observed in the open field, animals treated with P. ginseng, glycine and ketamine when compared to white. These data suggest that the doses of P. ginseng employed were unable to induce general toxicity in rats treated for 30 days and also shows that the general behavior of mice treated with P. ginseng was slightly different from that observed in animals treated with ketamine and glycine. Finally, the study on the elevated plus maze showed that the extract of P. ginseng showed no anxiolytic or anxiogenic action

A inserção da equipe da Estratégia Saúde da Família em um Centro Municipal de Educação Infantil na promoção da saúde da criança

The joint enters the teams of the Strategy Health of Family (ESF) and the Municipal Center of Infantile education (CMEI) blunts as a form to assure the monitoring and promotion to the health of the children of 2 the 5 years when entering the day-care center environment/daily pay-school. It was traced as objective: To analyze the actions developed for the team of the Strategy Health of the Family in the promotion the health of the child, taken care of in a CMEI. Description-exploratory is to a study, qualitative nature, the type research-action. Developed in a CMEI and the USF of the quarter of New City, Natal-RN. The population was constituted by the professionals of the team of the ESF and the CMEI and parents. During the stages of the research-action diverse techniques had been used as the individually interview and in group, focal group, comment participant, and daily of field. The analysis of the data occurred by means of the content analysis, in the thematic modality, proposal for Bardin (1977) and description of the stages of the research-action. In the stage of situational diagnosis that it investigates the reality lived deeply for the citizens of ESF and CMEI how much to the health of the child seven categories had emerged that they enclosed: the context of the attention child in the CMEI identifying the actions that already came being developed for the ESF in the CMEI; the functioning of the CMEI and its routine of activities; the paper of the CMEI in the care the child; the daily one of the ESF, how much to the care to the health of the child of 2 the 5 years involving the diverse difficulties faced for the ESF; difficulties faced in daily of the CMEI for the care the child of 2 the 5 years; paper of joint ESF and CMEI for the confrontation of the difficulties; e action of health to be developed that they had subsidized the stage of planning of the research-action. During the stages of planning and implementation of the actions the actions of education in health with professionals of the CMEI and parents had been materialize and the actions of direct attention the health of the child. In the stage of evaluation of the actions for the involved citizens one searched to ahead understand the perception of the actions developed and perspective of continuity of the actions, through 4 boarded subjects for the citizens. For all the passage of the research-action it can be inferred that joint ESF and CMEI is a necessary initiative ahead of the current situation of the services of health for the promotion of an integral attention the health of the child, but that the teams of the ESF not yet make use of material conditions and staff enough to develop actions that exceed the limits of the USF, being necessary for this the reinforcement of the joints mainly with the Federal University of the Rio Grande of the North.

Propriedades cerâmicas e imobilização do manganês em cerâmica estrutural

In this work is the addition of a metallic ion, of the metal Manganese, in a clay of Rio Grande do Norte state for structural ceramics use, the objective this study was to assess the evolution of ceramic properties. The clay was characterized by Chemical and Thermal analysis and Xray difraction. The metallic ion was added in the clay as aqueous solutions at concentrations of 100, 150 and 200 mg / L. The molded by extrusion and the burned were temperatures at 850, 950, 1050 and 1150 º C. Was made Chemical Analysis and investigated the following parameters environmental and ceramic: Solubility, Colour, Linear Retraction (%), Water Absorption (%), Gresification Curves, Apparent Porosity (%), Apparent Specific Mass (g/cm3) and Flexion Rupture Module (kgf/cm2). The results showed that increasing the concentration of metallic ion, properties such as Apparent Porosity (%), Water Absorption (%) decreases and the Flexion Rupture Module (kgf/cm2) increases with increasing temperature independent of the concentration of the ion. The gresification curves showed that the optimum firing temperatures were in the range between 950 and 1050 ° C. The evaluation of the properties showed that the ceramic material can be studied its use in solid brick and ceramic materials with structural function of filling. The results of solubility showed that the addition of ion offers no risk to the environment

Balanço energético de um forno túnel de cerâmica estrutural convertido de lenha para gás natural

In energy systems, the balance of entrances, exits and losses are fundamental to rationalize the energy consumption, independently of the source (sun, natural gas, wind, water, firewood or oil). This estimate is important so much in the phase of project of the facilities, as in the exploration or operation. In the project phase it indicates the energy needs of the process and the contribution of the energy in the cost of the product and the capacity of storage of the fuel and in the operation phase it allows to evaluate the use of the energy in the process of it burns, showing the weak points that should suffer intervention to improve the efficiency. With this tool, it can be implemented routines of calculation of thermal balances in ovens of it burns of structural ceramic, in way to generate an optimized mathematical model for application in the current and promising structural ceramic brazilian industry. The ceramic oven in study is located in the metropolitan area of Natal (Rio Grande do Norte) and it is a continuous oven of the type wagons tunnel, converted of firewood for natural gas and it produces blocks of red ceramic. The energy balance was applied in the oven tunnel before and after the conversion and made the comparisons of the energy efficiencies (it burns to the firewood and it burns to natural gas), what showed that the gaseous fuel is more efficient when we burn structural ceramic in ovens tunnels. When we burn natural gas, the requested energy is smaller and better used. Tests were accomplished in the burned product that showed the best quality of the burned brick with natural gas. That quality improvement makes possible to accomplish new interventions for the most rational use of the energy in the oven tunnel of the Ceramic in study and in the industries of structural ceramic of the whole Brazil, that need control tools of burning and of quality

Influência do teor e granulometria da calcita e da temperatura de sinterização no desenvolvimento de massas cerâmicas para revestimento poroso(BIII)

This work aims at studying the influence of the concentration of calcite, its grain size and sintering temperature to obtain porous coating formulations that meet the design specifications. The experiments involved the physical-chemical and mineralogical caracterization of the raw materials, and mechanical tests on specimens dried and sintered, performing a planning mixture and factorial experiment, using the response surface methodology. The ceramic bodies studied were prepared by dry process, characterized, placed in conformity by uniaxial pressing and sintered at temperatures of 940 º C, 1000ºC, 1060ºC, 1120°C and 1180°C using a fast-firing cycle. The crystalline phases formed during sintering at temperatures under study, revealed the presence of anorthite and wolastonite, and quartz-phase remaining. These phases were mainly responsible for the physical and mechanical properties of the sintered especimens. The results shown that as increases the participation of carbonate in the composition of ceramic bodies there is an increase of water absorption and a slight reduction in linear shrinkage for all sintering temperatures. As for the mechanical strength it was observed that it tended to decrease for sintering at temperatures between 940 ° C and 1060 ° C and to increase for sintering at temperatures above 1060 ° C occurring with greater intensity for compositions with higher content of calcite. The resistence decreased with increasing participation of quartz in all sintering temperatures. The decrease in grain size of calcite caused a slight increase in water absorption for formulation with the same concentration of carbonate, remaining virtually unchanged the results of linear shrinkage and mechanical strength. In conclusion, porous ceramic coating (BIII) can be obtained using high concentrations of calcite and keeping the properties required in technical standards and that the particle size of calcite can be used as tuning parameter for the properties of ceramic products.