Avaliação do comportamento tribológico de compósitos poliéster/fibra de vidro utilizando resíduos de poliéster/fibra de vidro e carbonato de cálcio como carga

The use of composite materials and alternative is being increased every day, as it becomes more widespread awareness that the use of renewable and not harmful to the environment is part of a new environmentally friendly model. Since its waste (primarily fiberglass) can not be easily recycled by the difficulty that still exists in this process, since they have two phases mixed, a polymeric matrix thermoset difficult to recycle because it is infusible and phase of fiber reinforcements. Thermoset matrix composites like Polyester + fiberglass pose a threat due to excessive discharge. Aiming to minimize this problem, aimed to reuse the composite Polyester + fiber glass, through the wastes obtained by the grinding of knifes and balls. These residues were incorporated into the new composite Polyester/Fiberglass for hot compression mold and compared tribological to composites with filler CaCO3, generally used as filler, targeting a partial replacement of CaCO3 by such waste. The composites were characterized by thermal analysis (TGA, DSC and DMA), by the surface integrity (roughness determination, contact angle and surface energy), mechanical properties (hardness) and tribological tests (wear and coefficient of dynamic friction) in order to evaluate the effect of loads and characterize these materials for applications that can take, in the tribological point of view since waste Polyester + fiberglass has great potential for replacement of CaCO3

Análise da lubricidade do biodiesel brasileiro de ésteres etílicos de soja e girassol

Fuel is a material used to produce heat or power by burning, and lubricity is the capacity for reducing friction. The aim of this work is evaluate the lubricity of eight fossil and renewable fuels used in Diesel engines, by means of a HFRR tester, following the ASTM D 6079-04 Standard. In this conception, a sphere of AISI 52100 steel (diameter of 6,000,05 mm, Ra 0,050,005 μm, E = 210 GPa, HRC 624, HV0,2 63147) is submitted to a reciprocating motion under a normal load of 2 N and 50 Hz frequency to promote a wear track length of 1.10.1mm in a plan disc of AISI 52100 steel (HV0,05 18410, Ra 0,020,005 μm). The testing extent time was 75 minutes, 225,000 cycles. Each one test was repeated six times to furnish the results, by means of intrinsic signatures from the signals of the lubricant film percentage, friction coefficient, contact heating, Sound Pressure Level, SPL [dB]. These signal signatures were obtained by two thermocouples and a portable decibelmeter coupled to a data acquisition system and to the HFRR system. The wettability of droplet of the diesel fuel in thermal equilibrium on a horizontal surface of a virgin plan disc of 52100 steel, Ra 0,02  0,005 μm, were measured by its contact angle of 7,0  3,5o, while the results obtained for the biodiesel B5, B20 and B100 blends originated by the ethylic transesterification of soybean oil were, respectively, 7,5  3,5o, 13,5  3,5o e 19,0  1,0o; for the distilled water, 78,0  6,0o; the biodiesel B5, B20 and B100 blends originated by the ethylic transesterification of sunflower oil were, respectively, 7,0  4,0o, 8,5  4,5o e 19,5  2,5o. Different thickness of lubricant film were formed and measured by their percentage by means of the contact resistance technique, suggesting several regimes, since the boundary until the hydrodynamic lubrication. All oils analyzed in this study promoted the ball wear scars with diameters smaller than 400 μm. The lowest values were observed in the scar balls lubricated by mixtures B100, B20 and B5 of sunflower and B20 and B5 of soybean oils (WSD < 215 μm)

Caracterização e análise das propriedades da fibra de Macambira (Bromelia Laciniosa)

Concern for the environment and the exploitation of natural resources has motivated the development of research in lignocellulosic materials, mainly from plant fibers. The major attraction of these materials include the fact that the fibers are biodegradable, they are a renewable natural resource, low cost and they usually produce less wear on equipment manufacturing when compared with synthetic fibers. Its applications are focused on the areas of technology, including automotive, aerospace, marine, civil, among others, due to the advantageous use in economic and ecological terms. Therefore, this study aims to characterize and analyze the properties of plant fiber macambira (bromelia laciniosa), which were obtained in the municipality of Ielmo Marino, in the state of Rio Grande do Norte, located in the region of the Wasteland Potiguar. The characterization of the fiber is given by SEM analysis, tensile test, TG, FTIR, chemical analysis, in addition to obtaining his title and density. The results showed that the extraction of the fibers, only 0.5% of the material is converted into fibers. The results for title and density were satisfactory when compared with other fibers of the same nature. Its structure is composed of microfibrils and its surface is roughened. The cross section has a non-uniform geometry, therefore, it is understood that its diameter is variable along the entire fiber. Values for tensile strength were lower than those of sisal fibers and curauá. The degradation temperature remained equivalent to the degradation temperatures of other vegetable fibers. In FTIR analysis showed that the heat treatment may be an alternative to making the fiber hydrophobic, since, at high temperature can remove the hemicellulose layer, responsible for moisture absorption. Its chemical constitution is endowed with elements of polar nature, so their moisture is around 8.5% which is equivalent to the percentage of moisture content of hydrophilic fibers. It can be concluded that the fiber macambira stands as an alternative materials from renewable sources and depending on the actual application and purpose, it may achieve satisfactory results

Utilização do éster de soja como biolubrificante

The lubricants found in the market are of mineral or synthetic origin and harm to humans and the environment, mainly due to their improper discard. Therefore industries are seeking to develop products that cause less environmental impact, so to decrease mainly, operator aggression the Cutting Fluids became an emulsion of oil / water or water / oil. However, the emulsion was not considered the most suitable solution for environmental question, therefore the search for biodegradable lubricants and which no are toxic continues and so vegetable oils are seen, again, as a basis for the production of lubricants. The biggest problem with these oils is their oxidative instability that is intensified when working at high temperatures. The process transesterification decreases the oxidation, however changes some physical and chemical properties. Therefore soybean oil after the transesterification process was subjected to tests of density, dynamic viscosity, kinematic viscosity which is calculated from two parameters mentioned, flash point and acidity. Besides the physico-chemical test the soybean oil was subjected to a dynamic test in a tribometer adapted from a table vise, whose induced wear was the adhesive and ultimately was used as cutting fluid in a process of turning in two different materials, steel 1045 and cast iron. This latter test presented results below the mineral cutting fluid which it was compared in all tests, already in other experiments the result was satisfactory and other experiments not, so that chemical additives can be added to the oil analyzed to try equate all parameters and so formulate a biolubrificante not toxic to apply in machining processes of metalworking industry

Estudo das propriedades físico-químicas do biodiesel e suas influências na deterioração dos elastômeros aplicados no sistema de injeção dos motores diesel

The biodiesel use has become important due to its renewable character and to reduce environmental impacts during the fuel burning. Theses benefit will be valid if the fuel shows good performance, chemistry stability and compatibility with engines. Biodiesel is a good fuel to diesel engines due to its lubricity. Then, the aimed of this study was to verify the physicalchemistry properties of biodiesel and their correlations with possible elastomers damage after biodiesel be used as fuel in an injection system. The methodology was divided in three steps: biodiesels synthesis by transesterification of three vegetable oil (soybean, palm and sunflower) and their physical-chemistry characterization (viscosity, oxidative stability, flash point, acidity, humidity and density); pressurized test of compatibility between elastomers (NBR and VITON) and biodiesel, and the last one, analyze of biodiesels lubricity by tribological test ball-plan( HFRR). Also, the effect of mixture of biodiesel and diesel in different concentrations was evaluated. The results showed that VITON showed better compatibility with all biodiesel blends in relation to NBR, however when VITON had contact with sunflower biodiesel and its blends the swelling degree suffer higher influences due to biodiesel humidity. For others biodiesels and theirs blends, this elastomer kept its mechanical properties constant. The better tribological performance was observed for blends with high biodiesel concentration, lower friction coefficient was obtained when palm biodiesel was used. The main mechanisms observed during the HFRR tests were abrasive and oxidative wear

Caracterização do óleo de carnaúba para uso como biolubrificante

Lubricant is responsible for reducing the wear on the friction protect the metal against oxidation, corrosion and dissipates excess heat, making it essential for the balance of a mechanical system, consequently prolonging the useful life of such a system. The origin of lubricating oils is usually mineral being extracted from the petroleum. But the search for a new source of production of lubricants and fuels it is necessary to meet future demands and reduce the possible environmental damage. For this reason, looking alternative means to produce certain products derived from petroleum, such as biodiesel, for example. Returning to the realm of lubricants, also one realizes this need for new raw materials for their production. Vegetable oil is a renewable resource and biodegradable, and its use entails advantages in environmental, social and economic. The development of this project aims to characterize the carnauba oil as a lubricant plant, or biolubricant. To analyze the oil carnauba tests as checking density, flash point, fire point, viscosity, viscosity, acid number, pH, copper corrosion, thermal conductivity and thermal resistivity were developed. In addition, for conducting the wear on the friction and the gradient of the system temperature, the analysis equipment is designed for wear on the friction. Based on these results, it is observed that the oil carnauba show good correlation to its application as biolubricant

Estudo tribológico de biolubrificantes com adição de nanopartículas de óxidos (zinco e cobre)

Currently, vegetable oils have been studied for bio-lubricants base that fits the new environmental standards. Since, in a world full of finite natural resources, mineral oils bring consequences to the environment due to its low biodegradability and toxicity, also it is important to consider that synthetic oils have a high cost The aim of this work is to obtain a biolubricant additived with oxide nanoparticles (ZnO and CuO) for better resistance to friction and wear, which is not toxic to the environment and have better adherence under boundary lubrication. The methodology consisted in the synthesis of bio-lubricants (soybean and sunflower base) by epoxidation reaction. Then, some physical-chemical analysis in bio-lubricants are made to characterize theses lubricants, such as, density, acidity, iodine value, viscosity, viscosity index. Later, the lubricants were additive with nanoparticles. The tribological performance was evaluated by the equipment HFRR (High Frequency Reciprocating Rig) consisting of a wear test ball-plan type. The characterization of wear analysis was performed by SEM / EDS. The results show that bio-lubricants may be synthesized by reaction of epoxidation with good conversion. Tribological point of view, the epoxidized oils are more effective than lubricant additived with the oxide nanoparticles, they had lower coefficients of friction and better rate of film formation in the study. However, because they are environmentally friendly, bio-lubricants gain the relevant importance in tribological field

Otimização do fresamento de roscas internas com a técnica de interpolação helicoidal

In machining of internal threads, dedicated tools, known as taps, are needed for each profile type, diameter, and low cutting speed values are used when compared to main machining processes. This restriction in the cutting speed is associated with the difficulty of synchronizing the tool s rotation speed and feed velocity in the process. This fact restricts the flexibility and makes machining lead times longer when manufacturing of components with threads is required. An alternative to the constraints imposed by the tap is the thread milling with helical interpolation technique. The technique is the fusion of two movements: rotation and helical interpolation. The tools may have different configurations: a single edge or multiple edges (axial, radial or both). However, thread milling with helical interpolation technique is relatively new and there are limited studies on the subject, a fact which promotes challenges to its wide application in the manufacturing shop floor. The objective of this research is determine the performance of different types of tools in the thread milling with helical interpolation technique using hardened steel workpieces. In this sense, four tool configurations were used for threading milling in AISI 4340 quenched and tempered steel (40 HRC). The results showed that climb cut promoted a greater number of machined threads, regardless of tool configuration. The upcut milling causes chippings in cutting edge, while the climb cutting promotes abrasive wear. Another important point is that increase in hole diameter by tool diameter ratio increases tool lifetime

Eficácia da utilização de grânulos de argila como veículo para a aplicação aérea de sulfentrazone e isoxaflutole em área de implantação de eucalipto

Realizou-se um experimento em uma área de implantação da cultura do eucalipto no município de São Miguel Arcanjo-SP, com o objetivo de avaliar a eficácia da aplicação aérea de grânulos de argila como veículo dos herbicidas sulfentrazone e isoxaflutole, no controle de plantas daninhas. Foi realizada aplicação aérea dos herbicidas sulfentrazone, nas doses de 500 e 750 g i.a. ha-1, e isoxaflutole, nas doses de 150 e 225 g i.a. ha-1, utilizando-se como veículo grânulos de argila com densidade de 1,05 g cm ³, alta capacidade de absorção (24 mL 100 g-1), alta resistência ao desgaste e tamanho das partículas entre 500 mícrons e 1 mm. Também foram feitas aplicações via líquida dos mesmos herbicidas e doses com um pulverizador convencional, acoplado a um trator. Além desses tratamentos, foi mantida uma parcela testemunha, sem aplicação dos herbicidas. Nas parcelas experimentais foram semeadas as espécies de plantas daninhas Brachiaria decumbens, Ipomoea grandifolia, Merremia cissoides e Panicum maximum, sendo realizadas avaliações visuais de controle aos 75 e 110 dias após a aplicação. em geral, foram observados, nas plantas daninhas avaliadas, resultados de controle semelhantes ou superiores para a aplicação aérea (via grânulos) até 75 DAA e superiores para essa modalidade de aplicação aos 110 DAA, indicando uma extensão no período do efeito do residual dos herbicidas estudados.

Sistemas de liberação de fármaco intrabolsa periodontal

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Desenvolvimento de um sistema a jato de plasma obtido em cátodo oco para deposição de filmes finos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior

Estresse entre professoras do ensino fundamental de escolas públicas estaduais

O artigo relata pesquisa que visou, entre outros objetivos, identificar a presença do estresse, a sintomatologia e as fases apresentadas pelos professores de 1ª a 4ª série do Ensino Fundamental atuantes em escolas públicas estaduais de uma cidade do Interior de São Paulo. Participaram do estudo 175 professores, perfazendo, aproximadamente, 70% dos profissionais de Ensino Básico I (PEB-I) em atuação no município. Para obtenção dos objetivos foram utilizados dois instrumentos de coleta de dados: o ISSL (Inventário de Sintomas de Estresse) e um questionário para caracterizar a população pesquisada. A pesquisa revelou que 56,6% dos professores estão experimentando estresse, cujos principais sintomas presentes são: sensação de desgaste físico constante, cansaço constante, tensão muscular, problemas com a memória, irritabilidade excessiva, cansaço excessivo, angústia/ansiedade diária, pensar constantemente em um só assunto e irritabilidade sem causa aparente.

Hipossalivação e seus fatores de risco em idosos funcionalmente independentes e não institucionalizados

The aim of this study was to investigate the risk factors related to hyposalivation among non-institutionalized independently living elderly people, living in Natal-RN, Brazil. The study was a control-case type and the data collection was accomplished by carrying a questionnaire, oral examination and a non-stimulated and stimulated sialometry. The cases were identified by values of salivary flow rate <0,1mL/min and stimulated ≤ 0,5 mL/min, and the controls were by observing the values of sialometry that were bigger than the previously defined parameters. Age and gender were used as pairing variables. The data were analyzed using X2 (α = 0,05) and odds ratio. The sample was composed of 98,1% female and 1,9% male, with mean age 68. There was not association between hyposalivation and the following studied variables: income, schooling, profession, dwelling conditions, domiciliary density, illness, number of teeth and use of prothesis. However, a link was found between hyposalivation and smoking frequency in the passet (OR=5,14), indicating that, referring to elderly people, the tabagism frequency habit was a risk factor to the studied condition. Therefore, refering to non-institutionalized independently elderly people, economic-social-demographic conditions, general and bucal health, diet and habits such as alcoholism have been not risk factors to hyposalivation. However, people that have been smoking have more risk to have the studied conditions

Edentulismo funcional e seus fatores de risco em adultos

The purpose of this study was to investigate the risk factors to the functional edentulism in adults aged 35 a 44 years old of Natal-RN, 278 adults took part in the study. They were all selected from a previous dental loss prevalence study thus being complemented by an active research. The study was a case-control based and data collection was made though a survey as well as with a clinical examination. The cases were identified through individuals with 20 or more teeth. Age and gender were used as variables of pairing off. The data was analyzed through chi-square, significant level of 95% to the checking of its force associations. The independent variables were grouped in three levels. The first one, more macro, is related to the region where the individual lives, which was also related to the second level, the family-based one, linked with a third level, at this low socio-economical level, where the domiciliary density was favorable, living in capital cities, regions with prime sanitary condicitions, with predominant possibility of accessing the public dental service, but in despite of this, only looking for this service when tooth ache is felt, where preferentially an aid dressing treatment is executed in detriment of preventive procedures. From all the samples, less than 25% of the individuals make use of tobacco and alcoholic beverages for quite a number of years. There was an association of functional edentulism with all the studied variables in a regional method. In the family-based with Critério Brasil (OR=4,45) and monthly wages (OR=9,62) and to an to an individual level, the associations took place with the current use of kind of attendance (OR=1,78), looks for dressing treatment (OR=2,51), does not look for preventive treatment (OR=3,31), pain as the main cause of demand (OR=1,92), previous treatment as the demanding reason for dental service (OR+0,28), interval of the last visit to the dental service (OR=1,35) and when advise was received (OR=1,66). It was noticed from the results that the functional edentulism is much more expressive in those families which live in environments with precarious social economical sanitary conditions. Such conditions seem to have a direct influence upon the family social economical conditions which are also shown in detriment to functional edentulism. In the same way, the collection of variants influence the social economical conditions of the individual, as well as the kind of dental service searched by them, the reason of the search and the interval of the last visit to the dental service were strong determiners to the functional edentulism. Beyond that, individual habits like the use of tobacco and its frequency on its previous use influenced in a significant way the existence of functional edentulism in the studied population

Avaliação clínica da relação entre o índice de placa, índice gengival, alinhamento dental, mucosa ceratinizada, tipo de periodonto e distúrbios oclusais com a ocorrência de recessão gengival

This study clinically evaluated the relationship of gingival recessions with the periodontal index of gingival and plaque, dental alignment, keratinized mocous, type of periodontal, and occlusal disorders. Study participants were individuals aged between 19 and 33 years. The evaluations were performed by using questionnaires and clinical examinations. In subjects examined, the teeth were assessed and divided into groups (Molars, premolars, canines and incisors). The gingival recession were measured in the central region of the teeth and individuals were subject to disclosure to the plate and observing the poll of plaque and gingival index, respectively. 558 teeth were examined, with 24.1%, 135 had gingival recession greater than or equal to 1mm. Through the combination of tests used to evaluate the average of the recession and its relationship with the variables studied, we observed that the degree of recession of the elements assessed dental showed, almost for the most part, when higher values associated with the index plaque (p = 0.101), Gingival Index (p = 0.053), dental alignment (p = 0.962), width of keratinized mocous (p = 0.004) and type of periodontium (p = 0.033), however statistically significant difference could only be considered when related the recessions in the keratinized mocous and the type of the periodontium. Although we identify, when we evaluate the whole set of teeth that occlusal disturbances (p = 0.002) were more strongly associated with cases of gum recession that the gingival index (p = 0.006), however, these two conditions were correlated with the cases of recession, contributing to its occurrence