Shear Strength and Durability Testing of Adhesive Bonds in Cross-Laminated Timber

The paper addresses the quality of the interface and edge bonded joints in layers of cross-laminated timber (CLT) panels. The shear performance was studied to assess the suitability of two different adhesives, Polyurethane (PUR) and Phenol-Resorcinol-Formaldehyde (PRF), and to determine the optimum clamping pressure. Since there is no established testing procedure to determine the shear strength of the surface bonds between layers in a CLT panel, block shear tests of specimens in two different configurations were carried out, and further shear tests of edge bonded specimen in two configurations were performed. Delamination tests were performed on samples which were subjected to accelerated aging to assess the durability of bonds in severe environmental conditions. Both tested adhesives produced boards with shear strength values within the edge bonding requirements of prEN 16351 for all manufacturing pressures. While the PUR specimens had higher shear strength values, the PRF specimens demonstrated superior durability characteristics in the delamination tests. It seems that the test protocol introduced in this study for crosslam bonded specimens, cut from a CLT panel, and placed in the shearing tool horizontally, accurately reflects the shearing strength of glue lines in CLT.

Real-Time Channel Model Selection Using Windowed Received Signal Strength Measurements

This paper investigates the potential for using the windowed variance of the received signal strength to select from a set of predetermined channel models for a wireless ranging or localization system. An 868 MHz based measurement system was used to characterize the received signal strength (RSS) of the off-body link formed between two wireless nodes attached to either side of a human thorax and six base stations situated in the local surroundings.

Strength reduction of till under dynamic pore pressure condition

Cuttings in heavily overconsolidated clays are known to be susceptible to progressive deformation caused by creep and fatigue that usually begins at the toe of the slope. The progressive deformation leads to strength reduction with time at constant stress (or called softening) and could be accelerated by fluctuation of groundwater level associated with more extreme rainfall events predicted through climate change. The purpose of this paper is to assess the mechanism of progressive deformation due to creep and fatigue using element testing on samples of till. The samples were subjected to fully drained loading and the deviator stresses were held constant at various percentages of peak failure stress, while the pore water pressure was kept static or dynamic (fluctuating ±5 kPa) over a period of time. The results have shown that the samples experienced significant deformation even at a higher factor of safety (i.e. the failure deviator stress/deviator stress at which the pore water pressure was fluctuated) under pore water pressure dynamics.

Predicting impact damage, residual strength and crashworthiness of composite structures

The development of the latest generation of wide-body carbon-fibre composite passenger aircraft has heralded a new era in the utilisation of these materials. The premise of superior specific strength and stiffness, corrosion and fatigue resistance, is tempered by high development costs, slow production rates and lengthy and expensive certification programmes. Substantial effort is currently being directed towards the development of new modelling and simulation tools, at all levels of the development cycle, to mitigate these shortcomings. One of the primary challenges is to reduce the extent of physical testing, in the certification process, by adopting a ‘certification by simulation’ approach. In essence, this aspirational objective requires the ability to reliably predict the evolution and progression of damage in composites. The aerospace industry has been at the forefront of developing advanced composites modelling tools. As the automotive industry transitions towards the increased use of composites in mass-produced vehicles, similar challenges in the modelling of composites will need to be addressed, particularly in the reliable prediction of crashworthiness. While thermoset composites have dominated the aerospace industry, thermoplastics composites are likely to emerge as the preferred solution for meeting the high-volume production demands of passenger road vehicles. This keynote presentation will outline recent progress and current challenges in the development of finite-element-based predictive modelling tools for capturing impact damage, residual strength and energy absorption capacity of thermoset and thermoplastic composites for crashworthiness assessments.

Strength and ductility of RC jacketed columns: a simplified analytical method

Reinforced concrete (RC) jacketing is a common method for retrofitting existing columns with poor structural performance. It can be applied in two different ways: if the continuity of the jacket is ensured, the axial load of the column can be transferred to the jacket, which will be directly loaded; conversely, if no continuity is provided, the jacket will induce only confinement action. In both cases the strength and ductility evaluation is rather complex, due to the different physical phenomena included, such as confinement, core-jacket composite action, preload and buckling of longitudinal bars.
Although different theoretical studies have been carried out to calculate the confinement effects, a practical approach to evaluate the flexural capacity and ductility is still missing. The calculation of these quantities is often related to the use of commercial software, taking advantage of numerical methods such as fibre method or finite element method.
This paper presents a simplified approach to calculate the flexural strength and ductility of square RC jacketed sections subjected to axial load and bending moment. In particular the proposed approach is based on the calibration of the stress-block parameters including the confinement effect. Equilibrium equations are determined and buckling of longitudinal bars is modelled with a suitable stress-strain law. Moment-curvature curves are derived with simple calculations. Finally, comparisons are made with numerical analyses carried out with the code OpenSees and with experimental data available in the literature, showing good agreement.

A randomized controlled trial on the effects of combined aerobic-resistance exercise on muscle strength and fatigue, glycemic control and health-related quality of life of type 2 diabetes patients

Aim: to evaluate the effects of a 12-weeks combined aerobic-resistance exercise therapy on fatigue and isokinetic muscle strength, glycemic control and health-related quality of life (HRQoL) in moderately affected type 2 diabetes (T2DM) patients. Methods: a randomized controlled trial design was employed. Forty-three T2DM patients were assigned to an exercise group (n = 22), performing 3 weekly sessions of 60 minutes of combined aerobic-resistance exercise for 12-weeks; or a no exercise control group (n = 21). Both groups were evaluated at a baseline and after 12-weeks of exercise therapy for: 1) muscle strength and fatigue by isokinetic dynamometry; 2) plasma glycated hemoglobin A1C (HbA1C); and 3) HRQoL utilizing the SF-36 questionnaire. Results: the exercise therapy led to improvements in muscle fatigue in knee extensors (-55%) and increased muscle strength in knee flexors and extensors (+15 to +30%), while HbA1C decreased (-18%). In addition, the exercising patients showed sizeable improvements in HRQoL: physical function (+53%), vitality (+21%) and mental health (+40%). Conclusion: 12-weeks of combined aerobic-resistance exercise was highly effective to improve muscle strength and fatigue, glycemic control and several aspects of HRQoL in T2DM patients. These data encourage the use of aerobic and resistance exercise in the good clinical care of T2DM.

Famílias envelhecidas: percursos e diversidade

O conhecimento sobre famílias envelhecidas é ainda escasso. Neste âmbito, a pesquisa tem incidido nos cuidados familiares a idosos dependentes, focando os problemas de saúde, dependência funcional e declínio cognitivo. Esta investigação pretende contribuir para aprofundar o conhecimento sobre as famílias envelhecidas, assumindo uma perspetiva normativa e desenvolvimental, e contemplando a diversidade de contextos de vida e envelhecimento. O capítulo 1 centra casais compostos por pessoas idosas, e tem por objetivos: caracterizar a estrutura, dinâmica e valores do agregado familiar dos casais idosos; evidenciar valores e dinâmica relacional dos casais idosos. A amostra compreende 136 participantes, a quem foi administrado um questionário sobre a fase última do ciclo de vida familiar (Cerveny,1997). A análise de dados efetuou-se com recurso ao programa de análise de dados estatística SPSS 17.1. Os resultados indicam que os casais vivem predominantemente em casal, com uma dinâmica relacional do agregado caracterizada pelo respeito, diálogo e carinho; dinâmica relacional do casal caracterizada por clima afetuoso, amizade e diálogo, e valores assentes no amor, diálogo e convívio familiar. A dinâmica relacional do casal é pautada por atividades de lazer realizadas em conjunto e vida sexual tão boa como antes; os valores dão ao casamento significados de realização pessoal e perpetuação através dos filhos na juventude, e adaptação e descoberta na velhice. O capítulo 2 foca a construção da integridade familiar considerando a diversidade de contextos socioeconómicos (pessoas idosas que viveram em contexto de pobreza ao longo da vida), socioculturais (ex-emigrantes portugueses) e novas formas de famílias (homens homossexuais). Foi aplicada uma entrevista semiestruturada (King & Wynne, 2004) a uma amostra de 12, 20 e 10 pessoas, respetivamente. A análise de dados foi efetuada com base na análise de conteúdo com recurso a juízes independentes baseada na grounded theory, contudo no caso do contexto socioeconómico recorreu-se ao programa de análise de dados qualitativa N-Vivo 7. Os resultados sugerem que a diversidade de contextos analisada coloca desafios à rutura familiar o que pode potenciar o caminho da desconexão e alienação. Contudo, o contexto das significações exerce um papel fundamental na construção da integridade familiar. A redefinição da identidade associada a uma filosofia de vida que enfatize as forças em vez dos fracassos parece determinar a construção da integridade familiar, contudo existem especificidades. Relativamente ao contexto socioeconómico: as pessoas idosas no caminho da integridade revelam um sentido de autovalorização (ter vivido uma vida significativa) apesar da pobreza; as pessoas idosas no caminho da desconexão/alienação alimentam sentimentos de insignificância devido à escassez de recursos económicos. Ainda neste contexto, os valores (princípios de conduta) reinterpretam a identidade ao longo da vida e permitem compreender que a integridade familiar ocorre quando ser pobre é encarado pelas conquistas; a desconexão/alienação emerge quando ser pobre incorpora sentimentos de desvalorização e inferioridade. No contexto sociocultural, as pessoas idosas ex-emigrantes cujo processo de emigração se desenvolveu em família (a família está envolvida no processo de emigração e funciona como um pilar desde a fase de decisão até ao regresso) desenvolveram uma filosofia de vida assente numa atitude ativa e solidária e estão em integridade familiar; as pessoas em desconexão relatam episódios de conflito familiar que marcam a trajetória de emigração, e uma atitude passiva na resolução desses conflitos até à atualidade; as pessoas em alienação familiar, cujo processo de emigração se desenrolou de forma solitária, desenvolvem uma filosofia de vida assente na luta solitária: a sua força e identidade estão em enfrentar tudo sem precisar de ninguém. Relativamente às novas formas de família, a integridade familiar evolui desde a revelação da homossexualidade (em idade jovem) e conclui-se na velhice quando a homossexualidade se torna um legado. A desconexão parece evoluir da luta constante da falha da aceitação da homossexualidade pela família e outras pessoas significativas. O capítulo 3 analisa as trajetórias de vida de homens homossexuais atualmente idosos, para compreender melhor a influência da homossexualidade e os principais eventos. Adotou-se a técnica da linha de acontecimentos de vida (Acquaviva et al., 2007), aplicada a 10 participantes com 60 anos ou mais. Os resultados sugerem que vários eventos de vida influenciam o curso de vida: i) o autoconhecimento da homossexualidade; ii) tentar passar por heterossexual; iii) assumir a homossexualidade (explicita ou implicitamente); iv) sentir limitações e desafios relacionados com o ser idoso e homossexual. O capítulo 4 procurou alargar a perspetiva do envelhecimento considerando uma abordagem transcultural. Assim, realizou-se um estudo numa comunidade indígena (Guarani Mbya, Brasil). Neste estudo analisase o modo de viver e ser idoso nessa comunidade. A amostra compreende 6 participantes a quem foi administrada uma entrevista aberta. Este estudo contemplou ainda a observação com registo etnográfico e realização de um diário de bordo. A análise de conteúdo efetuou-se com apoio do software de dados qualitativa WebQDA 1.4.3. Os resultados sugerem o papel das pessoas idosas na preservação de uma cultura ágrafa, garantindo que as tradições estejam presentes nas gerações atuais através da oralidade. A adoção de lentes normativas no estudo e compreensão das famílias envelhecidas permite compreender as tarefas desenvolvimentais e normativas no fim da vida.

Strength of visual percept generated by famous faces perceived without awareness: effects of affective valence, response latency, and visual field

Participants who were unable to detect familiarity from masked 17 ms faces ([Stone and Valentine, 2004] and [Stone and Valentine, in press-b]) did report a vague, partial visual percept. Two experiments investigated the relative strength of the visual percept generated by famous and unfamiliar faces, using masked 17 ms exposure. Each trial presented simultaneously a famous and an unfamiliar face, one face in LVF and the other in RVF. In one task, participants responded according to which of the faces generated the stronger visual percept, and in the other task, they attempted an explicit familiarity decision. The relative strength of the visual percept of the famous face compared to the unfamiliar face was moderated by response latency and participants’ attitude towards the famous person. There was also an interaction of visual field with response latency, suggesting that the right hemisphere can generate a visual percept differentiating famous from unfamiliar faces more rapidly than the left hemisphere. Participants were at chance in the explicit familiarity decision, confirming the absence of awareness of facial familiarity.

Developmental switch in the kinase dependency of long-term potentiation depends on expression of GluA4 subunit-containing AMPA receptors

The AMPA-receptor subunit GluA4 is expressed transiently in CA1 pyramidal neurons at the time synaptic connectivity is forming, but its physiological significance is unknown. Here we show that GluA4 expression is sufficient to alter the signaling requirements of long-term potentiation (LTP) and can fully explain the switch in the LTP kinase dependency from PKA to Ca2(+)/calmodulin-dependent protein kinase II during synapse maturation. At immature synapses, activation of PKA leads to a robust potentiation of AMPA-receptor function via the mobilization of GluA4. Analysis of GluA4-deficient mice indicates that this mechanism is critical for neonatal PKA-dependent LTP. Furthermore, lentiviral expression of GluA4 in CA1 neurons conferred a PKA-dependent synaptic potentiation and LTP regardless of the developmental stage. Thus, GluA4 defines the signaling requirements for LTP and silent synapse activation during a critical period of synapse development.

Effect of plug-filling, Testing velocity and temperature on the tensile strength of strap repairs on aluminium structures

In this work, an experimental study was performed on the influence of plug-filling, loading rate and temperature on the tensile strength of single-strap (SS) and double-strap (DS) repairs on aluminium structures. Whilst the main purpose of this work was to evaluate the feasibility of plug-filling for the strength improvement of these repairs, a parallel study was carried out to assess the sensitivity of the adhesive to external features that can affect the repairs performance, such as the rate of loading and environmental temperature. The experimental programme included repairs with different values of overlap length (L O = 10, 20 and 30 mm), and with and without plug-filling, whose results were interpreted in light of experimental evidence of the fracture modes and typical stress distributions for bonded repairs. The influence of the testing speed on the repairs strength was also addressed (considering 0.5, 5 and 25 mm/min). Accounting for the temperature effects, tests were carried out at room temperature (≈23°C), 50 and 80°C. This permitted a comparative evaluation of the adhesive tested below and above the glass transition temperature (T g), established by the manufacturer as 67°C. The combined influence of these two parameters on the repairs strength was also analysed. According to the results obtained from this work, design guidelines for repairing aluminium structures were

Shear strength of adhesively bonded polyolefins with minimal surface preparation

Interest in polyethylene and polypropylene bonding has increased in the last years. However, adhesive joints with adherends which are of low surface energy and which are chemically inert present several difficulties. Generally, their high degree of chemical resistance to solvents and dissimilar solubility parameters limit the usefulness of solvent bonding as a viable assembly technique. One successful approach to adhesive bonding of these materials involves proper selection of surface pre-treatment prior to bonding. With the correct pre-treatment it is possible to glue these materials with one or more of several adhesives required by the applications involved. A second approach is the use of adhesives without surface pre-treatment, such as hot melts, high tack pressure-sensitive adhesives, solvent-based specialty adhesives and, more recently, structural acrylic adhesives as such 3M DP-8005® and Loctite 3030®. In this paper, the shear strengths of two acrylic adhesives were evaluated using the lap shear test method ASTM D3163 and the block shear test method ASTM D4501. Two different industrial polyolefins (polyethylene and polypropylene) were used for adherends. However, the focus of this study was to measure the shear strength of polyethylene joints with acrylic adhesives. The effect of abrasion was also studied. Some test specimens were manually abraded using 180 and 320 grade abrasive paper. An additional goal of this work was to examine the effect of temperature and moisture on mechanical strength of adhesive joints.

Buckling strength of adhesively-bonded single and double-strap repairs on carbon-epoxy structures

This work reports on an experimental and finite element method (FEM) parametric study of adhesively-bonded single and double-strap repairs on carbon-epoxy structures under buckling unrestrained compression. The influence of the overlap length and patch thickness was evaluated. This loading gains a particular significance from the additional characteristic mechanisms of structures under compression, such as fibres microbuckling, for buckling restrained structures, or global buckling of the assembly, if no transverse restriction exists. The FEM analysis is based on the use of cohesive elements including mixed-mode criteria to simulate a cohesive fracture of the adhesive layer. Trapezoidal laws in pure modes I and II were used to account for the ductility of most structural adhesives. These laws were estimated for the adhesive used from double cantilever beam (DCB) and end-notched flexure (ENF) tests, respectively, using an inverse technique. The pure mode III cohesive law was equalled to the pure mode II one. Compression failure in the laminates was predicted using a stress-based criterion. The accurate FEM predictions open a good prospect for the reduction of the extensive experimentation in the design of carbon-epoxy repairs. Design principles were also established for these repairs under buckling.