Response of the arterial blood pressure of quadriplegic patients to treadmill gait training

Blood pressure pattern was analyzed in 12 complete quadriplegics with chronic lesions after three months of treadmill gait training. Before training, blood pressure values were obtained at rest, during treadmill walking and during the recovery phase. Gait training was performed for 20 min twice a week for three months. Treadmill gait was achieved using neuromuscular electrical stimulation, assisted by partial body weight relief (30-50%). After training, blood pressure was evaluated at rest, during gait and during recovery phase. Before and after training, mean systolic blood pressures and heart rates increased significantly during gait compared to rest (94.16 ± 5.15 to 105 ± 5.22 mmHg and 74.27 ± 10.09 to 106.23 ± 17.31 bpm, respectively), and blood pressure decreased significantly in the recovery phase (86.66 ± 9.84 and 57.5 ± 8.66 mmHg, respectively). After three months of training, systolic blood pressure became higher at rest (94.16 ± 5.15 mmHg before training and 100 ± 8.52 mmHg after training; P < 0.05) and during gait exercise (105 ± 5.22 mmHg before and 110 ± 7.38 mmHg after training; P < 0.05) when compared to the initial values, with no changes in heart rate. No changes occurred in blood pressure during the recovery phase, with the lower values being maintained. A drop in systolic pressure from 105 ± 5.22 to 86.66 ± 9.84 mmHg before training and from 110 ± 7.38 to 90 ± 7.38 mmHg after training was noticed immediately after exercise, thus resulting in hypotensive symptoms when chronic quadriplegics reach the sitting position from the upright position.

Modeling a Network of Heat Exchangers

This research work addresses the problem of building a mathematical model for the given system of heat exchangers and to determine the temperatures, pressures and velocities at the intermediate positions. Such model could be used in nding an optimal design for such a superstructure. To limit the size and computing time a reduced network model was used. The method can be generalized to larger network structures. A mathematical model which includes a system of non-linear equations has been built and solved according to the Newton-Raphson algorithm. The results obtained by the proposed mathematical model were compared with the results obtained by the Paterson approximation and Chen's Approximation. Results of this research work in collaboration with a current ongoing research at the department will optimize the valve positions and hence, minimize the pumping cost and maximize the heat transfer of the system of heat exchangers.

Öljy-vesiemulsioiden erottumisen tehostaminen erilaisten geometrioiden avulla

Työn kirjallisuusosassa selvitettiin neste-nestedispersioiden ja emulsioiden pisarakokojakauman määrittämiseen soveltuvia menetelmiä. Kirjallisuusosa painottuu emulsioiden stabiliteettiin liittyvään teoriaan ja menetelmiin, joilla voidaan tutkia pisarakokojakaumia suoraan prosessista. Erillisnäytteiden analysointiin perustuvista menetelmistä on esitettynä mikroskooppianalyysi sekä lasersäteen sirontaan perustuva mittaus, joita molempia käytettiin tämän työn kokeellisessa osassa. Kokeellisessa osassa pyrittiin selvittämään, vaikuttavatko kaksi erimuotoista ruuvi-kapaletta eri tavalla öljy-vesiemulsion pisarakokojakaumaan, kun emulsio virtasi ruuvin vuorovaikutusalueen läpi. Tätä tutkittiin määrittämällä ennen vuorovaikutusaluetta ja vuorovaikutusalueen jälkeen kerättyjen emulsionäytteiden pisarakokojakaumat lasersäteen sirontamittauksilla. Mitattujen pisarakokojakaumien perusteella ei voitu tehdä varmaa johtopäätöstä, vaikuttivatko ruuvit pisarakokojakaumaan vai eivät. Syynä tähän on pisarakokojakaumien vaihtelu rinnakkaisnäytteissä. Rinnakkaismittauksissa havaittu vaihtelu johtui arvaamattomasti muuttuneista virtausolosuhteista, mikä aiheutti edelleen öljypitoisuuden muutoksia. Muita mahdollisia syitä ovat veden ionivahvuuden, pH:n ja lämpötilan vaihtelu.

Leijukerroslämmönsiirtimien tukkeutuminen biovoimalaitoksessa

Leijukerroslämmönsiirtimien, eli hiekanpalautuspolvessa sijaitsevien tulistimien tukkeutuminen on ollut Kaukaan Voima Oy:n biovoimalaitoksen suunnittelemattomien seisokkien suurin syy vuodesta 2012 lähtien. Tulistimet tukkeutuvat kahdella tavalla. Nopeassa tukkeutumisessa tulistinkammion seinien kuonakerrostumat romahtavat yhtäkkiä tulistimen päälle tukkien sen. Tämä johtaa aina koko laitoksen alasajoon. Hitaassa tukkeutumisessa tulistinputkien pinnalle muodostuu vähitellen kerrostuma sekä tulistinputkien väliin jää suurempia kappaleita, jotka tukkivat tulistinta. Nopea tukkeutuminen johtuu tuhkassa olevien alkali-, eli kalium- ja natriumyhdisteiden synnyttämistä kerrostumista lämmönsiirrinkammion seinille. Hidas tukkeutuminen johtuu osittain myös alkaliyhdisteistä, mutta merkittävämpi aine tulistinputkien pinnalla olevassa kerrostumissa näyttää olevan kalsiumsulfaatti, joka tukkii tulistinta. Palavan aineen pääsy tulistinkammioon ilmanjakoasetuksista ja tulistinkammion rakenteesta johtuen aiheuttaa kerrostumien syntymisen. Kerrostumien syntymiseen johtavat syyt johtuvat monesta tekijästä ja yksiselitteistä aiheuttajaa on vaikea määritellä. Selvin yhteys on lietteen epätasaisessa poltossa ja turpeen käytössä. Nykyisillä lietteenkäsittelylaitteilla lietteen tasainen syöttö on vaikeaa ja se aiheuttaa ongelmia. Turpeen poltto biopolttoaineiden rinnalla pitää tulistimet puhtaampina. Muita todennäköisiä kerrostumia lisääviä syitä ovat puhtaan hiekan vähäinen syöttömäärä ja usean huonomman polttoaineen yhtäaikainen poltto.

Effect of hyperbaric oxygenation on mitochondrial function of neuronal cells in the cortex of neonatal rats after hypoxic-ischemic brain damage

The timing and mechanisms of protection by hyperbaric oxygenation (HBO) in hypoxic-ischemic brain damage (HIBD) have only been partially elucidated. We monitored the effect of HBO on the mitochondrial function of neuronal cells in the cerebral cortex of neonatal rats after HIBD. Neonatal Sprague-Dawley rats (total of 360 of both genders) were randomly divided into normal control, HIBD, and HIBD+HBO groups. The HBO treatment began immediately after hypoxia-ischemia (HI) and continued once a day for 7 consecutive days. Animals were euthanized 0, 2, 4, 6, and 12 h post-HI to monitor the changes in mitochondrial membrane potential (ΔΨm) occurring soon after a single dose of HBO treatment, as well as 2, 3, 4, 5, 6, and 7 days post-HI to study ΔΨm changes after a series of HBO treatments. Fluctuations in ΔΨm were observed in the ipsilateral cortex in both HIBD and HIBD+HBO groups. Within 2 to 12 h after HI insult, the ΔΨm of the HIBD and HIBD+HBO groups recovered to some extent. A secondary drop in ΔΨm was observed in both groups during the 1-4 days post-HI period, but was more severe in the HIBD+HBO group. There was a secondary recovery of ΔΨm observed in the HIBD+HBO group, but not in the HIBD group, during the 5-7 days period after HI insult. HBO therapy may not lead to improvement of neural cell mitochondrial function in the cerebral cortex in the early stage post-HI, but may improve it in the sub-acute stage post-HI.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.

Optimizing the Performance of a Heat Exchanger Network

This research is the continuation and a joint work with a master thesis that has been done in this department recently by Hemamali Chathurangani Yashika Jayathunga. The mathematical system of the equations in the designed Heat Exchanger Network synthesis has been extended by adding a number of equipment; such as heat exchangers, mixers and dividers. The solutions of the system is obtained and the optimal setting of the valves (Each divider contains a valve) is calculated by introducing grid-based optimization. Finding the best position of the valves will lead to maximization of the transferred heat in the hot stream and minimization of the pressure drop in the cold stream. The aim of the following thesis will be achieved by practicing the cost optimization to model an optimized network.

Inhibition of renal glucose reabsorption as a novel treatment for diabetes patients

The importance of the kidney in glucose homeostasis has been recognized for many years. Recent observations indicating a greater role of renal glucose metabolism in various physiologic and pathologic conditions have rekindled the interest in renal glucose handling as a potential target for the treatment of diabetes. The enormous capacity of the proximal tubular cells to reabsorb the filtered glucose load entirely, utilizing the sodium-glucose co-transporter system (primarily SGLT-2), became the focus of attention. Original studies conducted in experimental animals with the nonspecific SGLT inhibitor phlorizin showed that hyperglycemia after pancreatectomy decreased as a result of forced glycosuria. Subsequently, several compounds with more selective SGLT-2 inhibition properties (“second-generation”) were developed. Some agents made it into pre-clinical and clinical trials and a few have already been approved for commercial use in the treatment of type 2 diabetes. In general, a 6-month period of therapy with SGLT-2 inhibitors is followed by a mean urinary glucose excretion rate of ~80 g/day accompanied by a decline in fasting and postprandial glucose with average decreases in HgA1C ~1.0%. Concomitant body weight loss and a mild but consistent drop in blood pressure also have been reported. In contrast, transient polyuria, thirst with dehydration and occasional hypotension have been described early in the treatment. In addition, a significant increase in the occurrence of uro-genital infections, particularly in women has been documented with the use of SGLT-2 inhibitors. Conclusion: Although long-term cardiovascular, renal and bone/mineral effects are unknown SGLT-2 inhibitors, if used with caution and in the proper patient provide a unique insulin-independent therapeutic option in the management of obese type 2 diabetes patients.

Experimentation on Wind Powered Hydraulic Heating System

It is common knowledge of the world’s dependency on fossil fuel for energy, its unsustainability on the long run and the changing trend towards renewable energy as an alternative energy source. This aims to cut down greenhouse gas emission and its impact on the rate of ecological and climatic change. Quite remarkably, wind energy has been one of many focus areas of renewable energy sources and has attracted lots of investment and technological advancement. The objective of this research is to explore wind energy and its application in household heating. This research aims at applying experimental approach in real time to study and verify a virtually simulated wind powered hydraulic house heating system. The hardware components comprise of an integrated hydraulic pump, flow control valve, hydraulic fluid and other hydraulic components. The system design and control applies hardware in-the-loop (HIL) simulation setup. Output signal from the semi-empirical turbine modelling controls the integrated motor to generate flow. Throttling the volume flow creates pressure drop across the valve and subsequently thermal power in the system to be outputted using a heat exchanger. Maximum thermal power is achieved by regulating valve orifice to achieve optimum system parameter. Savonius rotor is preferred for its low inertia, high starting torque and ease of design and maintenance characteristics, but lags in power efficiency. A prototype turbine design is used; with power output in range of practical Savonius turbine. The physical mechanism of the prototype turbine’s augmentation design is not known and will not be a focus in this study.

Reducing auxiliary power of a fluid bed boiler island

The aim of this thesis is to find and analyze different methods which reduce fluid bed boilers’ auxiliary power consumption. The objective is to examine the effects and feasibility of these methods. The literature part explains how fluid bed boilers work and what are the main sources of auxiliary power consumption. Designs and operation of these equipment are presented. The literature part also discusses the basics of auxiliary power consumption reduction and introduces four low pressure drop constructions. The experimental part inspects six different methods. Effects of these methods on the auxiliary power consumption are calculated and their impacts on the operation of the boiler are modeled. Calculations show that reasonable changes can reduce fluid bed boiler’s auxiliary power consumption by 2,1-10,2 %. Biggest reductions come from lower air coefficients, smaller bed a-level pressures and lower primary/secondary air –ratios. Models showed no problems with the smaller bed a-level pressures. With the lower air coefficients and smaller primary/secondary air –ratios the models showed a significant increase in the carbon monoxide levels.

Synthesis and characterization of nanoperforated metal oxide thin films

For advanced devices in the application fields of data storage, solar cell and biosensing, one of the major challenges to achieve high efficiency is the fabrication of nanopatterned metal oxide surfaces. Such surfaces often require both precise structure at the nanometer scale and controllable patterned structure at the macro scale. Nowadays, the dominating candidates to fabricate nanopatterned surfaces are the lithographic technique and block-copolymer masks, most of which are unfortunately costly and inefficient. An alternative bottom-up approach, which involves organic/inorganic self-assembly and dip-coating deposition, has been studied intensively in recent years and has proven to be an effective technique for the fabrication of nanoperforated metal oxide thin films. The overall objective of this work was to optimize the synthesis conditions of nanoperforated TiO2 (NP-TiO2) thin films, especially to be compatible with mixed metal oxide systems. Another goal was to develop fabrication and processing of NP-TiO2 thin films towards largescale production and seek new applications for solar cells and biosensing. Besides the traditional dip-coating and drop-casting methods, inkjet printing was used to prepare thin films of metal oxides, with the advantage of depositing the ink onto target areas, further enabling cost-effective fabrication of micro-patterned nanoperforated metal oxide thin films. The films were characterized by water contact angle determination, Atomic Force Microscopy, Scanning Electron Microscopy, X-ray Photoelectron Spectroscopy and Grazing Incidence XRay Diffraction. In this study, well-ordered zinc titanate nanoperforated thin films with different Zn/Ti ratios were produced successfully with zinc precursor content up to 50 mol%, and the dominating phase was Zn2Ti3O8. NP-TiO2 structures were also obtained by a cost-efficient means, namely inkjet printing, at both ambient temperature and 60 °C. To further explore new biosensing applications of nanoperforated oxide thin films, inkjet printing was used for the fabrication of both continuous and patterned polymeric films onto NP-TiO2 and perfluorinated phosphate functionalized NP-TiO2 substrates, respectively. The NP-TiO2 films can be also functionalized with a fluoroalkylsilane, resulting in hydrophobic surfaces on both titania and silica. The surface energy contrast in the nanoperforations can be tuned by irradiating the films with UV light, which provides ideal model systems for wettability studies.

Keräilykorttipelin toteutus HTML5- ja Javascript-tekniikoilla

HTML5-tekniikka sekä Javascript tuen laajuus selaimissa vaihtelee. Tässä työssä kyseisiä tekniikoita tutkitaan ja selvitetään niiden toimivuus keräilykorttipelin tarvittavien ominaisuuksien osalta. Tuet kartoitetaan viiden yleisimmän selaimen osalta. HTML5 tukee WebSocket-ominaisuutta, mutta kaikki selaimet eivät tue ominaisuutta tai se on poistettu käytöstä. Työssä etsitään tiedonsiirtotekniikan korvaaja, jota testataan ja verrattaan yleisesti käytettäviin tekniikoihin. Socket.io oli nopea tekniikka ja viisi yleisintä selainta tuki kyseistä tekniikkaa. Tämän vuoksi Socket.io-tekniikka soveltuu keräilykorttipeliin hyvin. Työssä tutkitaan keräilykorttipeliin liittyviä ongelmia sekä ratkaistaan ilmenneet ongelmat. Keräilykorttipelissä kyseisiä ongelmia ilmeni hyvin vähän. HTML5 animaatio tutkitaan että se on optimoitu hyvin, jotta käyttäjälle tulee miellyttävä peli kokemus. Keräilykorttipeliin lisäksi tehdään käytännön toteutuksena pakkaeditorin prototyyppi, jossa käytetään drag&drop-tekniikkaa. Tämän vuoksi myös drag&drop-tekniikan tuki on selainten osalta kartoitettu myös työssä, sekä testattu käytännön toteutuksena prototyypissä. Prototyypin tarkoitus on kartoittaa mahdolliset tulevat ongelmat sekä auttaa varsinaisen pakkaeditorin tuotantoversiossa.

Viimeisimmän finanssikriisin vaikutukset Helsingin Pörssin kulutuspalveluita tuottaviin yrityksiin

Tämän kandidaatintutkielman tarkoituksena on analysoida miten vuonna 2008 alkanut finanssikriisi ja sen aiheuttama taloudellinen epävarmuus ovat vaikuttaneet Nasdaq OMX Helsingin pörssiin listattujen kulutuspalveluita tuottavien yritysten suorituskykyyn. Näiden yritysten suorituskykyä analysoitiin tarkemmin tarkastelemalla kannattavuuden, maksuvalmiuden ja vakavaraisuuden tunnuslukuja aikavälillä 2008-2014. Tutkimuksen tavoitteena oli selvittää, minkälaisia muutoksia suorituskyvyn suhteen tutkitulla aikavälillä oli tapahtunut kulutuspalveluita tuottavien yritysten keskuudessa. Muutoksia analysoitiin sekä kokonaisuutena että yrityskohtaisesti. Lisäksi tutkittiin, miten kulutuspalveluryhmän sisäiset toimialat olivat selviytyneet finanssikriisistä. Käsiteltävää yritysryhmää analysoitiin tunnuslukuanalyysiä hyödyntäen. Saatujen tulosten mukaan finanssikriisillä ei ollut suurta vaikutusta käsiteltävien yritysten maksuvalmiuteen tai vakavaraisuuteen. Kannattavuuden tunnusluvut sen sijaan heikkenivät merkittävästi koko ryhmän osalta finanssikriisin vaikutuksesta. Yrityskohtaiset erot olivat tutkimuksessa melko suuria. Etenkin mediayhtiöiden tunnusluvut heikkenivät merkittävästi tutkitulla aikavälillä. Mediayhtiöiden huonoon suoriutumiseen liittyy finanssikriisin lisäksi muitakin tekijöitä. Median digitalisoituminen on aiheuttanut useille yrityksille ongelmia liiketoiminnan kannattavuuden ylläpitämisessä. Monet tutkituista yrityksistä ovat kuitenkin pystyneet kääntämään liiketoimintansa kannattavampaan suuntaan vuoden 2013 jälkeen. Johtopäätöksenä voidaankin vetää, että viimeisin finanssikriisi oli vaikutuksiltaan merkittävä ja pitkäkestoinen.

Variable-speed-drive-based detection methods for problems in fluid handling systems

Fluid handling systems account for a significant share of the global consumption of electrical energy. They also suffer from problems, which reduce their energy efficiency and increase life-cycle costs. Detecting or predicting these problems in time can make fluid handling systems more environmentally and economically sustainable to operate. In this Master’s Thesis, significant problems in fluid systems were studied and possibilities to develop variable-speed-drive-based detection methods for them was discussed. A literature review was conducted to find significant problems occurring in fluid handling systems containing pumps, fans and compressors. To find case examples for evaluating the feasibility of variable-speed-drive-based methods, queries were sent to industrial companies. As a result of this, the possibility to detect heat exchanger fouling with a variable-speed drive was analysed with data from three industrial cases. It was found that a mass flow rate estimate, which can be generated with a variable speed drive, can be used together with temperature measurements to monitor a heat exchanger’s thermal performance. Secondly, it was found that the fouling-related increase in the pressure drop of a heat exchanger can be monitored with a variable speed drive. Lastly, for systems where the flow device is speed controlled with by a pressure measurement, it was concluded that increasing rotational speed can be interpreted as progressing fouling in the heat exchanger.

Learning to be literate : parental empowerment in early literacy interventions

Considerable research has focused on the success of early intervention programs for children. However, minimal research has focused on the effect these programs have on the parents of targeted children. Many current early intervention programs champion family-focused and inclusive programming, but few have evaluated parent participation in early interventions and fewer still have evaluated the impact of these programs on beliefs and attitudes and parenting practices. Since parents will continue to play a key role in their child's developmental course long after early intervention programs end, it is vital to examine whether these programs empower parents to take action to make changes in the lives of their children. The goal of this study was to understand parental influences on the early development of literacy, and in particular how parental attitudes, beliefs and self efficacy impact parent and child engagement in early literacy intervention activities. A mixed method procedure using quantitative and qualitative strategies was employed. A quasi-experimental research design was used. The research sample, sixty parents who were part of naturally occurring community interventions in at- risk neighbourhoods in a south-western Ontario city participated in the quantitative phase. Largely individuals whose home language was other than English, these participants were divided amongst three early literacy intervention groups, a Prescriptive Interventionist type group, a Participatory Empowering type group and a drop-in parent- child neighbourhood Control group. Measures completed pre and post a six session literacy intervention, on all three literacy and evidence of change in parental empowerment. Parents in all three groups, on average, held beliefs about early literacy that were positive and that were compatible with current approaches to language development and emergent literacy. No significant change in early literacy beliefs and attitudes for pre to post intervention was found. Similarly, there was no significant difference between groups on empowerment scores, but there was a significant change post intervention in one group's empowerment score. There was a drop in the empowerment score for the Prescriptive Interventionist type group, suggesting a drop in empowerment level. The qualitative aspect of this study involved six in-depth interviews completed with a sub-set of the sixty research participants. Four similar themes emerged across the groups: learning takes place across time and place; participation is key; success is achieved by taking small steps; and learning occurs in multiple ways. The research findings have important implications for practitioners and policy makers who target at risk populations with early intervention programming and wish to sustain parental empowerment. Study results show the value parents place on early learning and point to the importance of including parents in the development and delivery of early intervention programs. groups, were analyzed for evidence of change in parental attitudes and beliefs about early literacy and evidence of change in parental empowerment. Parents in all three groups, on average, held beliefs about early literacy that were positive and that were compatible with current approaches to language development and emergent literacy. No significant change in early literacy beliefs and attitudes for pre to post intervention was found. Similarly, there was no significant difference between groups on empowerment scores, but there was a significant change post intervention in one group's empowerment score. There was a drop in the empowerment score for the Prescriptive Interventionist type group, suggesting a drop in empowerment level. The qualitative aspect of this study involved six in-depth interviews completed with a sub-set of the sixty research participants. Four similar themes emerged across the groups: learning takes place across time and place; participation is key; success is achieved by taking small steps; and learning occurs in multiple ways. The research findings have important implications for practitioners and policy makers who target at risk populations with early intervention programming and wish to sustain parental empowerment. Study results show the value parents place on early learning and point to the importance of including parents in the development and delivery of early intervention programs.