Structural changes and dynamic behaviour of vanadium oxide-based catalysts for gas-phase selective oxidations

Selective oxidation is one of the simplest functionalization methods and essentially all monomers used in manufacturing artificial fibers and plastics are obtained by catalytic oxidation processes. Formally, oxidation is considered as an increase in the oxidation number of the carbon atoms, then reactions such as dehydrogenation, ammoxidation, cyclization or chlorination are all oxidation reactions. In this field, most of processes for the synthesis of important chemicals used vanadium oxide-based catalysts. These catalytic systems are used either in the form of multicomponent mixed oxides and oxysalts, e.g., in the oxidation of n-butane (V/P/O) and of benzene (supported V/Mo/O) to maleic anhydride, or in the form of supported metal oxide, e.g., in the manufacture of phthalic anhydride by o-xylene oxidation, of sulphuric acid by oxidation of SO2, in the reduction of NOx with ammonia and in the ammoxidation of alkyl aromatics. In addition, supported vanadia catalysts have also been investigated for the oxidative dehydrogenation of alkanes to olefins , oxidation of pentane to maleic anhydride and the selective oxidation of methanol to formaldehyde or methyl formate [1]. During my PhD I focused my work on two gas phase selective oxidation reactions. The work was done at the Department of Industrial Chemistry and Materials (University of Bologna) in collaboration with Polynt SpA. Polynt is a leader company in the development, production and marketing of catalysts for gas-phase oxidation. In particular, I studied the catalytic system for n-butane oxidation to maleic anhydride (fluid bed technology) and for o-xylene oxidation to phthalic anhydride. Both reactions are catalyzed by systems based on vanadium, but catalysts are completely different. Part A is dedicated to the study of V/P/O catalyst for n-butane selective oxidation, while in the Part B the results of an investigation on TiO2-supported V2O5, catalyst for o-xylene oxidation are showed. In Part A, a general introduction about the importance of maleic anhydride, its uses, the industrial processes and the catalytic system are reported. The reaction is the only industrial direct oxidation of paraffins to a chemical intermediate. It is produced by n-butane oxidation either using fixed bed and fluid bed technology; in both cases the catalyst is the vanadyl pyrophosphate (VPP). Notwithstanding the good performances, the yield value didn’t exceed 60% and the system is continuously studied to improve activity and selectivity. The main open problem is the understanding of the real active phase working under reaction conditions. Several articles deal with the role of different crystalline and/or amorphous vanadium/phosphorous (VPO) compounds. In all cases, bulk VPP is assumed to constitute the core of the active phase, while two different hypotheses have been formulated concerning the catalytic surface. In one case the development of surface amorphous layers that play a direct role in the reaction is described, in the second case specific planes of crystalline VPP are assumed to contribute to the reaction pattern, and the redox process occurs reversibly between VPP and VOPO4. Both hypotheses are supported also by in-situ characterization techniques, but the experiments were performed with different catalysts and probably under slightly different working conditions. Due to complexity of the system, these differences could be the cause of the contradictions present in literature. Supposing that a key role could be played by P/V ratio, I prepared, characterized and tested two samples with different P/V ratio. Transformation occurring on catalytic surfaces under different conditions of temperature and gas-phase composition were studied by means of in-situ Raman spectroscopy, trying to investigate the changes that VPP undergoes during reaction. The goal is to understand which kind of compound constituting the catalyst surface is the most active and selective for butane oxidation reaction, and also which features the catalyst should possess to ensure the development of this surface (e.g. catalyst composition). On the basis of results from this study, it could be possible to project a new catalyst more active and selective with respect to the present ones. In fact, the second topic investigated is the possibility to reproduce the surface active layer of VPP onto a support. In general, supportation is a way to improve mechanical features of the catalysts and to overcome problems such as possible development of local hot spot temperatures, which could cause a decrease of selectivity at high conversion, and high costs of catalyst. In literature it is possible to find different works dealing with the development of supported catalysts, but in general intrinsic characteristics of VPP are worsened due to the chemical interaction between active phase and support. Moreover all these works deal with the supportation of VPP; on the contrary, my work is an attempt to build-up a V/P/O active layer on the surface of a zirconia support by thermal treatment of a precursor obtained by impregnation of a V5+ salt and of H3PO4. In-situ Raman analysis during the thermal treatment, as well as reactivity tests are used to investigate the parameters that may influence the generation of the active phase. Part B is devoted to the study of o-xylene oxidation of phthalic anhydride; industrially, the reaction is carried out in gas-phase using as catalysts a supported system formed by V2O5 on TiO2. The V/Ti/O system is quite complex; different vanadium species could be present on the titania surface, as a function of the vanadium content and of the titania surface area: (i) V species which is chemically bound to the support via oxo bridges (isolated V in octahedral or tetrahedral coordination, depending on the hydration degree), (ii) a polymeric species spread over titania, and (iii) bulk vanadium oxide, either amorphous or crystalline. The different species could have different catalytic properties therefore changing the relative amount of V species can be a way to optimize the catalytic performances of the system. For this reason, samples containing increasing amount of vanadium were prepared and tested in the oxidation of o-xylene, with the aim of find a correlations between V/Ti/O catalytic activity and the amount of the different vanadium species. The second part deals with the role of a gas-phase promoter. Catalytic surface can change under working conditions; the high temperatures and a different gas-phase composition could have an effect also on the formation of different V species. Furthermore, in the industrial practice, the vanadium oxide-based catalysts need the addition of gas-phase promoters in the feed stream, that although do not have a direct role in the reaction stoichiometry, when present leads to considerable improvement of catalytic performance. Starting point of my investigation is the possibility that steam, a component always present in oxidation reactions environment, could cause changes in the nature of catalytic surface under reaction conditions. For this reason, the dynamic phenomena occurring at the surface of a 7wt% V2O5 on TiO2 catalyst in the presence of steam is investigated by means of Raman spectroscopy. Moreover a correlation between the amount of the different vanadium species and catalytic performances have been searched. Finally, the role of dopants has been studied. The industrial V/Ti/O system contains several dopants; the nature and the relative amount of promoters may vary depending on catalyst supplier and on the technology employed for the process, either a single-bed or a multi-layer catalytic fixed-bed. Promoters have a quite remarkable effect on both activity and selectivity to phthalic anhydride. Their role is crucial, and the proper control of the relative amount of each component is fundamental for the process performance. Furthermore, it can not be excluded that the same promoter may play different role depending on reaction conditions (T, composition of gas phase..). The reaction network of phthalic anhydride formation is very complex and includes several parallel and consecutive reactions; for this reason a proper understanding of the role of each dopant cannot be separated from the analysis of the reaction scheme. One of the most important promoters at industrial level, which is always present in the catalytic formulations is Cs. It is known that Cs plays an important role on selectivity to phthalic anhydride, but the reasons of this phenomenon are not really clear. Therefore the effect of Cs on the reaction scheme has been investigated at two different temperature with the aim of evidencing in which step of the reaction network this promoter plays its role.

Ingegnerizzazione e design di nanoparticelle core-shell di magnetite/silice

In the past decade the study of superparamagnetic nanoparticles has been intensively developed for many biomedical applications such as magnetically assisted drug delivery, MRI contrast agents, cells separation and hyperthermia therapy. All of these applications require nanoparticles with high magnetization, equipped also with a suitable surface coating which has to be non-toxic and biocompatible. In this master thesis, the silica coating of commercially available magnetic nanoparticles was investigated. Silica is a versatile material with many intrinsic features, such as hydrophilicity, low toxicity, proper design and derivatization yields particularly stable colloids even in physiological conditions. The coating process was applied to commercial magnetite particles dispersed in an aqueous solution. The formation of silica coated magnetite nanoparticles was performed following two main strategies: the Stöber process, in which the silica coating of the nanoparticle was directly formed by hydrolysis and condensation of suitable precursor in water-alcoholic mixtures; and the reverse microemulsions method in which inverse micelles were used to confine the hydrolysis and condensation reactions that bring to the nanoparticles formation. Between these two methods, the reverse microemulsions one resulted the most versatile and reliable because of the high control level upon monodispersity, silica shell thickness and overall particle size. Moving from low to high concentration, within the microemulsion region a gradual shift from larger particles to smaller one was detected. By increasing the amount of silica precursor the silica shell can also be tuned. Fluorescent dyes have also been incorporated within the silica shell by linking with the silica matrix. The structure of studied nanoparticles was investigated by using transmission electron microscope (TEM) and dynamic light scattering (DLS). These techniques have been used to monitor the syntetic procedures and for the final characterization of silica coated and silica dye doped nanoparticles. Finally, field dependent magnetization measurements showed the magnetic properties of core-shell nanoparticles were preserved. Due to a very well defined structure that combines magnetic and luminescent properties together with the possibility of further functionalization, these multifunctional nanoparticles are potentially useful platforms in biomedical fields such as labeling and imaging.

A novel phase variation mechanism in the meningococcus driven by a ligand-responsive repressor and differential spacing of distal promoter elements

Phase variable expression, mediated by high frequency reversible changes in the length of simple sequence repeats, facilitates adaptation of bacterial populations to changing environments and is frequently important in bacterial virulence. Here we elucidate a novel phase variable mechanism for NadA expression, an adhesin and invasin of Neisseria meningitidis. The NadR repressor protein binds to operators flanking the phase variable tract of the nadA promoter gene and contributes to the differential expression levels of phase variant promoters with different numbers of repeats, likely due to different spacing between operators. It is shown that IHF binds between these operators, and may permit looping of the promoter, allowing interaction of NadR at operators located distally or overlapping the promoter. The 4-hydroxyphenylacetic acid, a metabolite of aromatic amino acid catabolism that is secreted in saliva, induces nadA expression by inhibiting the DNA binding activity of the NadR repressor. When induced, only minor differences are evident between NadR-independent transcription levels of promoter phase variants, which are likely due to differential RNA polymerase contacts leading to altered promoter activity. These results suggest that NadA expression is under both stochastic and tight environmental-sensing regulatory control, and both regulations are mediated by the NadR repressor that and may be induced during colonization of the oropharynx where it plays a major role in the successful adhesion and invasion of the mucosa. Hence, simple sequence repeats in promoter regions may be a strategy used by host-adapted bacterial pathogens to randomly switch between expression states that may nonetheless still be induced by appropriate niche-specific signals.

Supramolecular functional assemblies with photo or chemical addressability

Supramolecular self-assembly represents a key technology for the spontaneous construction of nanoarchitectures and for the fabrication of materials with enhanced physical and chemical properties. In addition, a significant asset of supramolecular self-assemblies rests on their reversible formation, thanks to the kinetic lability of their non-covalent interactions. This dynamic nature can be exploited for the development of “self-healing” and “smart” materials towards the tuning of their functional properties upon various external factors. One particular intriguing objective in the field is to reach a high level of control over the shape and size of the supramolecular architectures, in order to produce well-defined functional nanostructures by rational design. In this direction, many investigations have been pursued toward the construction of self-assembled objects from numerous low-molecular weight scaffolds, for instance by exploiting multiple directional hydrogen-bonding interactions. In particular, nucleobases have been used as supramolecular synthons as a result of their efficiency to code for non-covalent interaction motifs. Among nucleobases, guanine represents the most versatile one, because of its different H-bond donor and acceptor sites which display self-complementary patterns of interactions. Interestingly, and depending on the environmental conditions, guanosine derivatives can form various types of structures. Most of the supramolecular architectures reported in this Thesis from guanosine derivatives require the presence of a cation which stabilizes, via dipole-ion interactions, the macrocyclic G-quartet that can, in turn, stack in columnar G-quadruplex arrangements. In addition, in absence of cations, guanosine can polymerize via hydrogen bonding to give a variety of supramolecular networks including linear ribbons. This complex supramolecular behavior confers to the guanine-guanine interactions their upper interest among all the homonucleobases studied. They have been subjected to intense investigations in various areas ranging from structural biology and medicinal chemistry – guanine-rich sequences are abundant in telomeric ends of chromosomes and promoter regions of DNA, and are capable of forming G-quartet based structures– to material science and nanotechnology. This Thesis, organized into five Chapters, describes mainly some recent advances in the form and function provided by self-assembly of guanine based systems. More generally, Chapter 4 will focus on the construction of supramolecular self-assemblies whose self-assembling process and self-assembled architectures can be controlled by light as external stimulus. Chapter 1 will describe some of the many recent studies of G-quartets in the general area of nanoscience. Natural G- quadruplexes can be useful motifs to build new structures and biomaterials such as self-assembled nanomachines, biosensors, therapeutic aptamer and catalysts. In Chapters 2-4 it is pointed out the core concept held in this PhD Thesis, i.e. the supramolecular organization of lipophilic guanosine derivatives with photo or chemical addressability. Chapter 2 will mainly focus on the use of cation-templated guanosine derivatives as a potential scaffold for designing functional materials with tailored physical properties, showing a new way to control the bottom-up realization of well-defined nanoarchitectures. In section 2.6.7, the self-assembly properties of compound 28a may be considered an example of open-shell moieties ordered by a supramolecular guanosine architecture showing a new (magnetic) property. Chapter 3 will report on ribbon-like structures, supramolecular architectures formed by guanosine derivatives that may be of interest for the fabrication of molecular nanowires within the framework of future molecular electronic applications. In section 3.4 we investigate the supramolecular polymerizations of derivatives dG 1 and G 30 by light scattering technique and TEM experiments. The obtained data reveal the presence of several levels of organization due to the hierarchical self-assembly of the guanosine units in ribbons that in turn aggregate in fibrillar or lamellar soft structures. The elucidation of these structures furnishes an explanation to the physical behaviour of guanosine units which display organogelator properties. Chapter 4 will describe photoresponsive self-assembling systems. Numerous research examples have demonstrated that the use of photochromic molecules in supramolecular self-assemblies is the most reasonable method to noninvasively manipulate their degree of aggregation and supramolecular architectures. In section 4.4 we report on the photocontrolled self-assembly of modified guanosine nucleobase E-42: by the introduction of a photoactive moiety at C8 it is possible to operate a photocontrol over the self-assembly of the molecule, where the existence of G-quartets can be alternately switched on and off. In section 4.5 we focus on the use of cyclodextrins as photoresponsive host-guest assemblies: αCD–azobenzene conjugates 47-48 (section 4.5.3) are synthesized in order to obtain a photoresponsive system exhibiting a fine photocontrollable degree of aggregation and self-assembled architecture. Finally, Chapter 5 contains the experimental protocols used for the research described in Chapters 2-4.

Analisi chinesiologica della risposta muscolare indotta in una varietà di esercizi di core training

Il concetto di "core training" è ampiamente diffuso nelle moderne metodologie di allenamento, nonostante sia spesso collegato a pratiche da campo non pienamente supportate dalla ricerca scientifica. Il termine "core" identifica il "centro funzionale del corpo" in grado di garantire una "adeguata stabilità prossimale al fine di ottimizzare la mobilità distale", sostenendo il complesso lombo-pelvico e permettendo la connessione funzionale tra arti e tronco. La muscolatura del core, cositutita principalmente dalla regione addominale e paraspinale, è ben condizionabile dall'utilizzo di superfici instabili quali Bosu e Fitball, strumenti comuni nel settore sportivo e rieducativo ma sui quali esistono teorie e conoscenze altamente eterogenee. Obiettivo della presente tesi è, dunque, da un lato quello di confrontare una varietà di esercizi eseguibili su entrambe le superfici instabili precedentemente citate al fine di determinare le attivazioni muscolari a livello del "core", dall'altro quello di valutare gli effetti indotti da un "core training" di 8 settimane su parametri performance-specifici. Lo studio, effettuato su atleti aventi una elevata esperienza in tale settore, evidenzia valori elettromiografici superiori nella Fitball e Bosu rispetto al tappeto, seppure in maniera non significativa; circa il legame con aspetti prestativi, emerge invece come un allenamento specifico ad alto impatto nervoso, modulato secondo un target razionale, consenta di incrementare l'endurance della muscolatura addominale, l'equilibrio funzionale dinamico e la capacità di trasmissione di forze arti-tronco, giustificandone un utilizzo in vari settori dell'attività motoria.

Core-shell macromolecules with dendritic polyphenylene core and polymer shells

Core-shell macromolecules with dendritic polyphenylene core and polymer shell Zusammenfassung / Abstract Core-shell macromolecular structures have become of great interest in materials science because they gave an opportunity to combine a large variety of chemical and physical properties in the single molecule, by combination of different (in terms of chemistry and physics) cores and shells. The interest in such complex structures was provoked by their potential applications in the coating and painting industry (latexes), as supports for catalysts in polymer industry, or as nano-containers and transporters for genes or drug delivery. The aim of this study was the synthesis, characterization and further application of core-shell macromolecules possessing a hydrophobic stiff core (polyphenylene dendrimers) surrounded with a hydrophilic, soft, covalently bonded polymer shell (poly(ethylene oxide) and its copolymers). The requirements for such complex substances were that they should be well-defined in terms of molecular weight (narrow molecular weight distribution) and in molecular structure. The preparation of core-shell molecules containing dendrimer as a core was possible via two synthetic routs: “grafting-onto” and “grafting-from”. The resulting core-shell macromolecules possessed narrow polydispersity as guaranteed by the excellent structural and functional definition of the dendrimer and the narrow polydispersity of the PEO, PS-b-PEO and PI-b-PEO attached to the dendrimer surface. Additional investigation of the size of the particles indicated a relation between both the length and the number of the polymer chains and the hydrodynamic radius determined by Dynamic Light Scattering and Fluorescent Correlation Spectroscopy. Core-shell nano-particles were applied as metallocene supports in heterogeneous olefin polymerizations. Our results indicate that such catalyst systems, that have a size of at least one order of magnitude smaller than the used by now organic supports, could be very useful as model compounds for investigations on catalyst fragmentation and its influence on the product parameters.

Die Rolle Prolin-reicher Sequenzmotive des Core-Proteins in der Morphogenese des Hepatitis-B Virus

Diese Arbeit hatte zum Ziel, den Ausschleusungsmechanismus des Hepatitis-B Virus zu beleuchten. Es ist bisher unbekannt, wie das virale Nukleokapsid umhüllt und das reife Virion aus der Leberzelle freigesetzt wird. Bei einigen RNA-Viren, beispielsweise HIV-1, Ebola oder RSV, vermitteln so genannte Late-Domänen im viralen Kapsid- oder Matrix-Protein die Knospung der Viren an intrazellulären Membranen oder der Plasmamembran. Da das HBV-Core-Protein ähnliche Sequenzen trägt, wurde in der vorliegenden Arbeit überprüft, welche Rolle diese im viralen Replikationszyklus spielen. Meine Ergebnisse zeigen, dass die beiden Prolin-reichen Sequenzen PPAY (129-132) und PPNAP (134-138), die retroviralen Late-Domänen ähneln, für die HBV-Morphogenese essentiell sind. Mutationen einzelner Aminosäuren innerhalb dieser Motive führen zu Phänotypen mit verändertem Kapsid-, Nukleokapsid- und Virus-Bildungs-Vermögen. Insbesondere sind die Aminosäure Tyrosin 132 des Motivs PPAY und die Prolinreste 134 und 135 des Motivs PPNAP erforderlich, da diese schon für die Bildung der Kapside unentbehrlich sind. Charakteristisch für beide Motive sind auch die hier gezeigten Interaktionen mit speziellen Wirtszellfaktoren, deren physiologische Funktion es ist, zelluläre Proteine in den endosomalen Sortierungsprozess einzuschleusen. Im Vordergrund stehen hier die E3 Ub-Ligase Nedd4, welche Proteine mit Ub konjugiert und diese so signifikant für die Einschleusung in das endosomale System markiert, und Tsg101, das als zentrale Komponente des ESCRT-I-Komplexes für die Erkennung von ubiquitinierten Proteinen zuständig ist und diese dadurch in die ESCRT-Kaskade des multivesikulären Endosoms einführt. Für die genannten Interaktionen ist das Motiv PPAY und hier wieder speziell das Tyrosin 132 des HBV-Core-Proteins für die Wechselwirkung mit Nedd4 notwendig. Hingegen vermittelt die L-Domänen-ähnliche Sequenz PPNAP die Assoziation von Core mit Tsg101, wobei die beiden Prolinreste 134 und 135 und auch das Asparagin 136 für die Interaktion essentiell sind. Sowohl Nedd4 als auch Tsg101 wirken im Zusammenhang mit Ubiquitin, weshalb eine Ubiquitinierung von Core, trotz bislang negativer Nachweise, wahrscheinlich ist. Zugunsten dieser Annahme spricht auch mein Nachweis, dass der Lysinrest an Position 96 des Core-Proteins, als potentieller Ub-Akzeptor, gerade in späten Schritten eine essentielle Rolle spielt. Weiterhin klärungsbedürftig ist auch die Frage, ob Core direkt mit Tsg101 und Nedd4 interagiert, oder ob andere Faktoren dazwischen geschaltet sind. Auch könnte mit Hilfe von siRNA-vermittelten Depletionsversuchen die physiologische Relevanz der Tsg101/Core-und Nedd4/Core-Interaktion weiterführend untersucht werden. Zudem zeigen meine Arbeiten, dass Core mit intrazellulären Membranen assoziiert, weshalb es interessant wäre, zu untersuchen, ob es sich hierbei um Membranen des endosomalen Systems handelt, an denen die finalen Schritte der Virus-Morphogenese stattfinden könnten.

Funzioni della subunità θ e del dominio PHP della subunità α nel core catalitico della DNA polimerasi III di Escherichia coli

Il core catalitico della DNA polimerasi III, composto dalle tre subunità α, ε e θ, è il complesso minimo responsabile della replicazione del DNA cromosomiale in Escherichia coli. Nell'oloenzima, α ed ε possiedono rispettivamente un'attività 5'-3' polimerasica ed un'attività 3'-5' esonucleasica, mentre θ non ha funzioni enzimatiche. Il presente studio si è concentrato sulle regioni del core che interagiscono direttamente con ε, ovvero θ (interagente all'estremità N-terminale di ε) e il dominio PHP di α (interagente all'estremità C-terminale di ε), delle quali non è stato sinora identificato il ruolo. Al fine di assegnare loro una funzione sono state seguite tre linee di ricerca parallele. Innanzitutto il ruolo di θ è stato studiato utilizzando approcci ex-vivo ed in vivo. I risultati presentati in questo studio mostrano che θ incrementa significativamente la stabilità della subunità ε, intrinsecamente labile. Durante gli esperimenti condotti è stata anche identificata una nuova forma dimerica di ε. Per quanto la funzione del dimero non sia definita, si è dimostrato che esso è attivamente dissociato da θ, che potrebbe quindi fungere da suo regolatore. Inoltre, è stato ritrovato e caratterizzato il primo fenotipo di θ associato alla crescita. Per quanto concerne il dominio PHP, si è dimostrato che esso possiede un'attività pirofosfatasica utilizzando un nuovo saggio, progettato per seguire le cinetiche di reazione catalizzate da enzimi rilascianti fosfato o pirofosfato. L'idrolisi del pirofosfato catalizzata dal PHP è stata dimostrata in grado di sostenere l'attività polimerasica di α in vitro, il che suggerisce il suo possibile ruolo in vivo durante la replicazione del DNA. Infine, è stata messa a punto una nuova procedura per la coespressione e purificazione del complesso α-ε-θ

Dye doped, core / shell silica nanoparticles: synthesis, characterization, & biotechnological applications

The aim of this thesis was to design, synthesize and develop a nanoparticle based system to be used as a chemosensor or as a label in bioanalytical applications. A versatile fluorescent functionalizable nanoarchitecture has been effectively produced based on the hydrolysis and condensation of TEOS in direct micelles of Pluronic® F 127, obtaining highly monodisperse silica - core / PEG - shell nanoparticles with a diameter of about 20 nm. Surface functionalized nanoparticles have been obtained in a one-pot procedure by chemical modification of the hydroxyl terminal groups of the surfactant. To make them fluorescent, a whole library of triethoxysilane fluorophores (mainly BODIPY based), encompassing the whole visible spectrum has been synthesized: this derivatization allows a high degree of doping, but the close proximity of the molecules inside the silica matrix leads to the development of self - quenching processes at high doping levels, with the concomitant fall of the fluorescence signal intensity. In order to bypass this parasite phenomenon, multichromophoric systems have been prepared, where highly efficient FRET processes occur, showing that this energy pathway is faster than self - quenching, recovering the fluorescence signal. The FRET efficiency remains very high even four dye nanoparticles, increasing the pseudo Stokes shift of the system, attractive feature for multiplexing analysis. These optimized nanoparticles have been successfully exploited in molecular imaging applications such as in vitro, in vivo and ex vivo imaging, proving themselves superior to conventional molecular fluorophores as signaling units.

From core rigidities to dynamic capabilities: the role of external knowledge. A multiple case study

This study focuses on the processes of change that firms undertake to overcome conditions of organizational rigidity and develop new dynamic capabilities, thanks to the contribution of external knowledge. When external contingencies highlight firms’ core rigidities, external actors can intervene in change projects, providing new competences to firms’ managers. Knowledge transfer and organizational learning processes can lead to the development of new dynamic capabilities. Existing literature does not completely explain how these processes develop and how external knowledge providers, as management consultants, influence them. Dynamic capabilities literature has become very rich in the last years; however, the models that explain how dynamic capabilities evolve are not particularly investigated. Adopting a qualitative approach, this research proposes four relevant case studies in which external actors introduce new knowledge within organizations, activating processes of change. Each case study consists of a management consulting project. Data are collected through in-depth interviews with consultants and managers. A large amount of documents supports evidences from interviews. A narrative approach is adopted to account for change processes and a synthetic approach is proposed to compare case studies along relevant dimensions. This study presents a model of capabilities evolution, supported by empirical evidence, to explain how external knowledge intervenes in capabilities evolution processes: first, external actors solve gaps between environmental demands and firms’ capabilities, changing organizational structures and routines; second, a knowledge transfer between consultants and managers leads to the creation of new ordinary capabilities; third, managers can develop new dynamic capabilities through a deliberate learning process that internalizes new tacit knowledge from consultants. After the end of the consulting project, two elements can influence the deliberate learning process: new external contingencies and changes in the perceptions about external actors.

Spinal cord injury: assessment of autonomic state-dependent control of cardiovascular system and body core temperature

Spinal cord injury (SCI) results not only in paralysis; but it is also associated with a range of autonomic dysregulation that can interfere with cardiovascular, bladder, bowel, temperature, and sexual function. The entity of the autonomic dysfunction is related to the level and severity of injury to descending autonomic (sympathetic) pathways. For many years there was limited awareness of these issues and the attention given to them by the scientific and medical community was scarce. Yet, even if a new system to document the impact of SCI on autonomic function has recently been proposed, the current standard of assessment of SCI (American Spinal Injury Association (ASIA) examination) evaluates motor and sensory pathways, but not severity of injury to autonomic pathways. Beside the severe impact on quality of life, autonomic dysfunction in persons with SCI is associated with increased risk of cardiovascular disease and mortality. Therefore, obtaining information regarding autonomic function in persons with SCI is pivotal and clinical examinations and laboratory evaluations to detect the presence of autonomic dysfunction and quantitate its severity are mandatory. Furthermore, previous studies demonstrated that there is an intimate relationship between the autonomic nervous system and sleep from anatomical, physiological, and neurochemical points of view. Although, even if previous epidemiological studies demonstrated that sleep problems are common in spinal cord injury (SCI), so far only limited polysomnographic (PSG) data are available. Finally, until now, circadian and state dependent autonomic regulation of blood pressure (BP), heart rate (HR) and body core temperature (BcT) were never assessed in SCI patients. Aim of the current study was to establish the association between the autonomic control of the cardiovascular function and thermoregulation, sleep parameters and increased cardiovascular risk in SCI patients.

Gpu-based many-core architecture emulation: A double level approach

The efficient emulation of a many-core architecture is a challenging task, each core could be emulated through a dedicated thread and such threads would be interleaved on an either single-core or a multi-core processor. The high number of context switches will results in an unacceptable performance. To support this kind of application, the GPU computational power is exploited in order to schedule the emulation threads on the GPU cores. This presents a non trivial divergence issue, since GPU computational power is offered through SIMD processing elements, that are forced to synchronously execute the same instruction on different memory portions. Thus, a new emulation technique is introduced in order to overcome this limitation: instead of providing a routine for each ISA opcode, the emulator mimics the behavior of the Micro Architecture level, here instructions are date that a unique routine takes as input. Our new technique has been implemented and compared with the classic emulation approach, in order to investigate the chance of a hybrid solution.

Core-shell particles and their application for superhydrophobic surfaces

During the last years great effort has been devoted to the fabrication of superhydrophobic surfaces because of their self-cleaning properties. A water drop on a superhydrophobic surface rolls off even at inclinations of only a few degrees while taking up contaminants encountered on its way. rnSuperhydrophobic, self-cleaning coatings are desirable for convenient and cost-effective maintenance of a variety of surfaces. Ideally, such coatings should be easy to make and apply, mechanically resistant, and long-term stable. None of the existing methods have yet mastered the challenge of meeting all of these criteria.rnSuperhydrophobicity is associated with surface roughness. The lotus leave, with its dual scale roughness, is one of the most efficient examples of superhydrophobic surface. This thesis work proposes a novel technique to prepare superhydrophobic surfaces that introduces the two length scale roughness by growing silica particles (~100 nm in diameter) onto micrometer-sized polystyrene particles using the well-established Stöber synthesis. Mechanical resistance is conferred to the resulting “raspberries” by the synthesis of a thin silica shell on their surface. Besides of being easy to make and handle, these particles offer the possibility for improving suitability or technical applications: since they disperse in water, multi-layers can be prepared on substrates by simple drop casting even on surfaces with grooves and slots. The solution of the main problem – stabilizing the multilayer – also lies in the design of the particles: the shells – although mechanically stable – are porous enough to allow for leakage of polystyrene from the core. Under tetrahydrofuran vapor polystyrene bridges form between the particles that render the multilayer-film stable. rnMulti-layers are good candidate to design surfaces whose roughness is preserved after scratch. If the top-most layer is removed, the roughness can still be ensured by the underlying layer.rnAfter hydrophobization by chemical vapor deposition (CVD) of a semi-fluorinated silane, the surfaces are superhydrophobic with a tilting angle of a few degrees. rnrnrn