Avaliação do comportamento reológico de pastas de cimento para poços de petróleo com adição de plastificantes

The isolation of adjacent zones encountered during oilwell drilling is carried out by Portland-based cement slurries. The slurries are pumped into the annular positions between the well and the casing. Their rheological behavior is a very important component for the cementing process. Nowadays, several alternative materials are used in oilwell cementing, with goal the modification and the improvement of their properties, mainly the increase of the fluidity. And this can be reached by using plasticizers additives able to account for different oilwell conditions, yielding compatible cement slurries and allowing enough time for the complete cementing operation. If the rheological properties of the slurry are properly characterized, the load loss and flow regime can be correctly predicted. However, this experimental characterization is difficult. Rheological models capable of describing the cement slurry behavior must be capable of predicting the slurry cement deformation within reasonable accuracy. The aim of this study was to characterize rheologically the slurries prepared with a especial class of Portland cement, water and plasticizers based on lignosulfonate, melamine and polycarboxylate at temperatures varying from 27°C to 72°C. The tests were carried out according to the practical recommendations of the API RP 10B guidelines. The results revealed a great efficiency and the dispersive power of the polycarboxylate, for all temperatures tested. This additive promoted high fluidity of the slurries, with no sedimentation. High lignosulfonate and melamine concentrations did not reduce the rheological parameters (plastic viscosity and yield stress) of the slurries. It was verified that these additives were not compatible with the type of cement used. The evaluated rheological models were capable of describing the behavior of the slurries only within concentration and temperature ranges specific for each type of additive

Desenvolvimento de sistemas de aditivos químicos para aplicação em cimentações de poços de petróleo

The primary cementing is an important step in the oilwell drilling process, ensuring the mechanical stability of the well and the hydraulic isolation between casing and formation. For slurries to meet the requirements for application in a certain well, some care in the project should be taken into account to obtain a cement paste with the proper composition. In most cases, it is necessary to add chemicals to the cement to modify its properties, according to the operation conditions and thus obtain slurries that can move inside the jacket providing a good displacement to the interest area. New technologies of preparation and use of chemicals and modernization of technological standards in the construction industry have resulted in the development of new chemical additives for optimizing the properties of building materials. Products such as polycarboxylate superplasticizers provide improved fluidity and cohesion of the cement grains, in addition to improving the dispersion with respect to slurries without additives. This study aimed at adapting chemical additives used in civil construction to be used use in oilwell cement slurries systems, using Portland cement CPP-Special Class as the hydraulic binder. The chemical additives classified as defoamer, dispersant, fluid loss controller and retarder were characterized by infrared absorption spectroscopy, thermogravimetric analyses and technological tests set by the API (American Petroleum Institute). These additives showed satisfactory results for its application in cement slurries systems for oil wells. The silicone-based defoamer promoted the reduction of air bubbles incorporated during the stirring of the slurries. The dispersant significantly reduced the rheological parameters of the systems studied. The tests performed with the fluid loss controller and the retarder also resulted in suitable properties for application as chemical additives in cement slurries

Isolation of Bacillus thuringiensis strains that contain Dipteran-specific cry genes from Ilha Bela (São Paulo, Brazil) soil samples

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Clinical evaluation of enalapril maleate and furosemide usage in dogs with degenerative myxomatous mitral valve, CHF functional class Ib

A doença degenerativa mixomatosa da válvula mitral (DDMVM) é uma cardiopatia de alta incidência na clínica médica de pequenos animais, acometendo mormente cães idosos e raças de pequeno porte. Desta forma, foi realizada uma investigação científica objetivando avaliar clinicamente a utilização dos fármacos maleato de enalapril e furosemida em cães com a referida enfermidade na classe funcional Ib da ICC, antes e após a terapêutica implantada. Para isso, utilizaram-se 16 cães portadores da valvulopatia supracitada, distribuídos em dois grupos; com o primeiro recebendo furosemida (n=8) e o segundo maleato de enalapril (n=8), durante 56 dias. Os cães foram avaliados em quatro momentos (T0, T14, T28 e T56 dias) quanto aos sinais clínicos e parâmetros hematológicos e bioquímico-séricos, que incluíram concentrações séricas da enzima conversora da angiotensina (ECA) e aldosterona, como também avaliações radiográficas, eletrocardiográficas, ecodopplercardiográficas e da pressão arterial. Os resultados quanto aos parâmetros clínicos, avaliações hematológicas e bioquímicas séricas não revelaram alterações significativas em ambos os grupos, mas reduções significativas nos valores de ECA e aldosterona no grupo que recebeu o maleato de enalapril foram identificadas. Ao exame radiográfico observou-se reduções nos valores de VHS e na variável onda Pms do eletrocardiograma em ambos os grupos, mas sem alterações nos valores da pressão arterial. Por sua vez, o ecodopplercardiograma evidenciou diminuição significativa das variáveis DIVEd/s nos grupos estudados e na FEC% nos cães que receberam somente enalapril. Portanto, a análise dos resultados encontrados indicou que a monoterapia fundamentada no maleato de enalapril apresentou melhor eficiência no controle do quadro clínico em pacientes da classe funcional Ib da ICC.

A leitura de literatura na escola: por uma educação emocional de crianças na educação infantil

This dissertation examines the contributions of juvenile literature reading for the problematization of the emotional experiences and conflicts of children at infant education. Its importance consists in providing useful information for the pedagogic work orientated to literature reading at the initial series of basic education, in order to increase the teacher s ability to explore the literary text from its instigating and enriching nature in view of the child s emotional experiences and conflicts. It is methodologically based on the principles of the qualitative research, what characterizes it as a case study. The research focused a level V-infant education class with 28 students in 5-6 age group, at a public school of Natal, State of Rio Grande do Norte (Brazil). The used resources were: audio recording, field diary, and interviews. Seventeen classes were carried out and they consisted in reading sessions of classic and contemporaneous tales, fables, and legends which used different didactic strategies. These sessions were developed in accordance with the reading experience through scaffolding instructions as it was described by Graves & Graves. The theoretical references were the studies of Amarilha (1997/ 2006), Bettelheim (2004), Coelho (1987/2000), Damásio (2005), Del Nero (2003), Eco (1994/2006), Held (1980), Iser (1996), Jauss (2002), Stierle (2002), Wallon (2007), Telles (2006), Yunes (2003), and Zilberman (1987). The analyses showed that literary reading in class is a special environment for inclusion of the reader s subjectivity; as well as the inclusion of their emotional experiences and their conflicts within the story by way of helping children think and become suitable for dealing with their inner feelings. The literary reading is presented as an experiential and formative activity which helps children understand their emotions through a process of identification, exteriorization, and catharsis; what implies that the esthetic experience from the text makes possible the reader s self-knowledge and increases the perception of his inner feelings and objective reality so that this reader has emotional capital to deal with life difficulties. It is important to highlight that the discussions carried out in the class represented a field of sharing experiences through which each reader had the chance to present their experience of life to the others, including their sorrows and sufferings, in order to help them to develop best strategies to deal with the social environment

A dimensão social do desenho: um estudo sobre as interações no processo de (re) construção imagética da criança no Ensino Fundamental

In the historical-cultural perspective, the drawing is processed by means of a shared and complex way, under diverse relations with the other and with the immersed signs of the culture. That is, something constituted by the social interactions and that can modify the structure of the psychological functions, therefore as socialized sign, propitiates the incorporation of the functions socially. In this way, the figuration carrier sensitive and established meanings historically disclosing the shared experiences and the ways of the subject to think and perceive the world. Such reflections gave shape to the main problem of this research: how to think over about the drawing at the school to incide in the reconstruction of the childs imaginative language? Under such perspective, this work deals with the interactions in the production process of the drawing of the children in a context of teach-Iearning of the elementary school having as goal to analyze the interactions established in the cIassroom in the process of production of the drawings; to propose situations of learnings that favor the advance graphical expression of the students; and to identify in the interactive games some relations between body expression and drawing. For its accomplishment, it was opted for the construction process based in the collaborative investigation by the fact to propitiate negotiations, sharing and confrontation of ideas, becoming possible a joint construction of the knowledge. For this research, the researcher and the collaborating teacher, as well as the involved children, become themselves into co-authors of the context studied. As locus of the research, it was chosen a first cycle class, with 30 students, from Municipal School Profª. Emília Ramos (Natal/RN - Brazil), whose election took in account the fact of this school to constitute in a promotional space of reflections and professional development of teachers in service and, at the same time, for presentinglimitations theoretic- methodological in the field of teaching for Arts. In the process of the research, it was perceived that the children with the support of the verbal language formulates meanings on the seen and imagined object, printing lines and forms that if overlap to the physiological aspects of the visual perception. That is, the drawing discloses a reality appraised, enriched for the picked up vision of the image, but the meanings established for the author, or observer who becomes it perceivable and identified. In the systemizing situations, it was observed that the teaching-Iearning process of the drawing, implies a co-construction between teachers and learners. And, moreover, the necessity to interlace emotion and cognition by means of plastic-corporal interactions that foment drawing experiences, whose process concurs for the imagenative reconstruct of the apprentices

Electrochemical sensor for sulfite determination based on a nanostructured copper-salen film modified electrode

The electrochemical preparation described herein involved the electrocatalytic oxidation of sulfite on a platinum electrode modified with nanostructured copper salen (salen=N,N'-ethylenebis(salicylideneiminato)) polymer films. The complex was prepared and electropolymerized at a platinum electrode in a 0.1 mol L-1 solution of tetrabutylammonium perchlorate in acetonitrile by cyclic voltammetry between 0 and 1.4V vs. SCE. After cycling the modified electrode in a 0.50 mol L-1 KCI solution, the estimated surface concentration was found to be equal to 2.2 x 10(-9) Mol cm(-2). This is a typical behavior of an electrode surface immobilized with a redox couple that can usually be considered as a reversible single-electron reduction/oxidation of the copper(II)/copper(III) couple. The potential peaks of the modified electrode in the electrolyte solution (aqueous) containing the different anions increase with the decrease of the ionic radius, demonstrating that the counter-ions influence the voltammetric behavior of the sensor. The potential peak was found to be linearly dependent upon the ratio [ionic charge]/[ionic radius]. The oxidation of the sulfite anion was performed at the platinum electrode at +0.9V vs. SCE. However, a significant decrease in the overpotential (+0.45V) was obtained while using the sensor, which minimized the effect of oxidizable interferences. A plot of the anodic current vs. the sulfite concentration for chronoamperometry (potential fixed = +0.45V) at the sensor was linear in the 4.0 x 10(-6) to 6.9 x 10(-5) mol L-1 concentration range and the concentration limit was 1.2 x 10(-6) mol L-1. The reaction order with respect to sulfite was determined by the slope of the logarithm of the current vs. the logarithm of the sulfite concentration. (C) 2009 Elsevier Ltd. All rights reserved.

Study of the interaction between cardiolipin bilayers and methylene blue in polymer-based Layer-by-Layer and Langmuir films applied as membrane mimetic systems

An increase of the reports involving mimetic systems has been observed. Briefly, these systems use biological phospholipids to exploit specific interactions between membrane-models and drugs. Here, the Layer-by-Layer (LbL) and Langmuir techniques were used to investigate the interaction between cardiolipin (CLP-negative phospholipid) and a cationic-like drug methylene blue (MB). Supported by a cationic polyelectrolyte (PAH), LbL films containing PAH/(CLP + MB) and PAH/(CLP + MB + AgNP) were grown up to 14 bilayers. The optical microscopy analysis revealed a decrease of the CLP vesicle sizes in the presence of MB as a possible consequence of the MB action onto the mechanical properties of the CLP membrane. From FTIR spectra, changes mainly related to peak position and band intensity and shape were observed in the spectra from PAH/CLP when in the presence of MB. The latter supports that the interactions between the phosphate and amine charged groups from CLP and PAH, respectively, established during the LbL film fabrication, besides the CLP hydrocarbon environment, are influenced by the presence of MB. Using the micro-Raman technique, a chemical mapping was build based on MB spectrum by resonance Raman scattering (RRS) and surface-enhanced resonance Raman scattering (SERRS). The later phenomenon was activated by Ag nanoparticles (AgNPs) trapped within the LbL film allowing collecting spectra for a single bilayer of PAH/(CLP + MB + AgNP). A rough estimation showed a SERRS amplification of 10(3) in comparison to RRS spectra. As a complementary approach, Langmuir films of CLP in the presence of co-spread MB were investigated through surface pressure vs mean molecular area (pi-A) isotherms. The results showed that for concentrations of MB below 100 mol%, the drug is expelled to water subphase for high values of surface pressure (condensed phase). For concentration at 100% and higher, the MB keeps bound to CLP floating monolayer. (C) 2010 Elsevier B.V. All rights reserved.

Spray layer-by-layer films based on phospholipid vesicles aiming sensing application via e-tongue system

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Development of Nanostructured Electrochemical Sensor Based on Polymer Film Nickel-Salen for Determination of Dissolved Oxygen

An amperometric oxygen sensor based on a polymeric nickel-salen (salen = N,N '-ethylenebis(salicydeneiminato)) film coated platinum electrode was developed. The sensor was constructed by electropolymerization of nickel-salen complex at a platinum electrode in acetonitrile/tetrabuthylamonium perchlorate by cyclic voltammetry. The voltammetric behavior of the modified electrode was investigated in 0.5 mol L-1 KCl solution in the absence and presende of molecular oxygen. A significant increased of cathodic peak current (at -0.20 vs. SCE) of the modified electrode with addition of oxygen to the solution was observed. This result shows that the nickel-salen film on the surface of the electrode promotes the reduction of oxygen. The reaction can be brought about electrochemically where in the nickel(II) complex is first reduced to a nickel(I) complex at the electrode surface. The nickel(I) complex then undergoes a catalytic oxidation by the oxygen molecular in solution back to the nickel(II) complex, which can then be electrochemically re-reduced to produce an enhancement of the cathodic current. The plot of the cathodic current versus the dissolved oxygen concentration for chronoamperometry (potential fixed = -0.20 V) at the sensor was linear in the concentration range of 3.95 to 9.20 mg L-1 with concentration limit of 0.17 mg L-1 O-2. The modified electrode proposed is useful for the quality control and routine analysis of dissolved oxygen in commercial water and environmental water samples. The results obtained for the levels of dissolved oxygen are in agreement with the results obtained with an O-2 commercial sensor. (C) 2011 Published by Elsevier Ltd.

Enzymeless Hydrogen Peroxide Sensor Based on Mn-containing Conducting Metallopolymer

The [(Mn4O5)-O-IV(terpy)(4)(H2O)(2)](6+) complex, show great potential for electrode modification by electropolymerization using cyclic voltammetry. The voltammetric behavior both in and after electropolymerization process were also discussed, where the best condition of electropolymerization was observed for low scan rate and 50 potential cycles. A study in glass electrode for better characterization of polymer was also performed. Electrocatalytic process by metal centers of the conducting polymer in H2O2 presence with an increase of anodic current at 0.85 V vs. SCE can be observed. The sensor showed great response from 9.9 x 10(-5) to 6.4 x 10(-4) mol L-1 concentration range with a detection limit of 8.8 x 10(-5) mol L-1, where the electrocatalytic mechanism was based on oxidation of H2O2 to H2O with consequently reduction of Mn-IV to Mn-III. After, the Mn-III ions are oxidized electrochemically to Mn-IV ions. (C) 2012 Elsevier Ltd .... Selection and/or peer-review under responsibility of the Symposium Cracoviense Sp. z.o.o.

Estimation of Maximal Work Rate Based on the 6-Minute Walk Test and Fat-Free Mass in Chronic Obstructive Pulmonary Disease

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Comparison of Impurity Profiles of Lipiblock (R) vs. Orlistat using HPLC and LC-MS/MS

Comparative HPLC-UV and LC-MS/MS studies of impurity profiles of a reference sample (Xenical (R), F. Hoffmann La Roche Ltd., Switzerland) vs. generic (Lipiblock (R), EMS Sigma Pharma, a generic drug) were carried out with ethanol extracts of commercial samples. The generic formulation contained higher levels of common impurities as well as a considerable number of impurities not found in the reference product. The detected impurity profile of Lipiblock (R) revealed that it most likely is based on fermentation. Since the effect of the impurities is unknown, at this point fully synthetic Xenical (R) appears to offer a better safety margin than Lipiblock (R) which, however, compares quite well to other generic formulations.

Knowledge-based integrated production management model

Purpose - This paper aims to propose a model of production management that integrates knowledge management, as a third dimension, to the production and work dimensions and to identify factors that promote a favorable context for knowledge sharing and results achievement in the production operations shop floor environment.Design/methodology/approach - The model proposed is built from opportunities identified in the literature review.Findings - The factors in the model integrate its three main components: knowledge management, production organization and work organization, providing a representation of the dynamics of the workplace and shop floor environment.Practical implications - The proposed model and its factors allow managers to better understand and to improve the organization activities, because it integrates knowledge management with the production organization and work organization components of traditional models.Originality/value - Literature acknowledges the role of knowledge as competitive advantage, but it is still dealt in an implicit way within the traditional models of production management. This paper proposes a model and factors that provide a favorable context for tacit knowledge sharing and results achievement in the production operations shop floor environment. The model explicitly integrates knowledge management with traditional models' components.

(Con)vivendo em fortalezas: o outro lado do morar bem

The intensification of the fear in the city and in the spaces controlled by this feeling has contributed to a growing socio-spatial inequality, and the rapid growth of market protection. The residential condos emerge as a possible solution to the problem. This is a housing typology expanding worldwide which is seen, especially by the urban middle class, as enablers of quality of life and safety. In Brazil, especially in large cities, the quest for quality of life is directly connected with the desire for security translated through space control (use of high walls, gates, entrance hall, security cameras) and people who use it. This thesis aims at investigating how the different categories of inhabitants of an area predominantly occupied by vertical residential condos realize the socio-spatial dimension and the socio-urban space determined by this type of development. It especially takes into consideration the issue of urban insecurity, based on the assumption that, although published and sold by marketing as safe places , synonym of welfare and supporters of community life , the living in these condos, may even inhibits, social relationships, contributing to socio-spatial isolation and consequent social weakness. This is a survey that seeks to meet the assumptions of Environmental Psychology towards the comprehension of person-environment studies, emphasizing the use of different methods (desk research, observations of and group interviews, focus group technique using photographic resources), as well as the focus on current problems of the urban scene and the knowledge gained in Social Psychology