Behavior of bulk melt-textured YBCO single domains subjected to crossed magnetic fields

We have experimentally investigated the crossed magnetic field effects on bulk melt-processed YBCO single domains. The samples were first permanently magnetized along their c-axis and then subjected to several cycles of a transverse magnetic field parallel to the ab planes. The magnetic properties along the c and ab directions were simultaneously measured using a couple of orthogonal pick-up coils as well as a Hall probe placed against the sample surface. The effects of both sweep amplitude and polarity were investigated. Field sweeps of alternate polarities are shown to affect the decay of the c-axis magnetization much more strongly than field sweeps of unique polarity do. However, the c-axis magnetization does not show any saturation even after a large number of field sweeps. Next, a micro-Hall probe scanning system was used to measure the distribution of magnetic induction over the top surface of the single domain subjected to the same combination of magnetic fields. The results are shown to be consistent with those determined with the sensing coils and bring out the role played by geometric effects.

Axial stiffness of journal bearings in zero-field and field-cooled modes

Superconducting journal bearings have been investigated for use in flywheel systems. We report on the zero-field cooled and field-cooled stiffness of these bearings. They are made up of radial magnet rings with alternating polarities, a pole pitch of 11 mm and a surface field of 0.1 T. Field-cooled stiffness of the journal bearings increased four times over the zero-field-cooled stiffness. © 2005 IEEE.

Report on the occurrence of one subspecies of Scylla serrata (Forskal) in Cochin backwaters

The taxonomy of the mud crab, Scylla serrata has become a topic of interest. Alcock (1899) described this species from Indian waters. It was considered that under the genus Scylla, only one species, namely, Scylla serrata was valid. But Estampador (1949) revised the genus and reported the occurrence of four sorts, Scylla serrata, S. tranquebarica, S. oceanica and a variety S. serrata, var paramarnosain in Philippine waters. He established his claim based on the morphology such as colouration, relative length of chelae and also on the cytological events during gametogenesis. Serene (1952) pointed out that two distinct categories under this genus were demonstrable on the basis of colouration. But Stephenson & Campbell (1960) concluded them as only synonyms, but pointed out the need for further investigations.

Evolution and biogeography of talpid moles from continental East Asia and the Japanese islands inferred from mitochondrial and nuclear gene sequences

We sequenced the cytochrome b gene from two little-studied mammal species from the highlands of Southwest China, the long-tailed mole Scaptonyx fusicaudus and the gracile shrew-like mole Uropsilus gracilis. This data was used to examine the phylogenetic r

Molecular phylogeny and biogeography of Oriental voles: genus Eothenomys (Muridae, Mammalia)

Oriental voles of the genus Eothenomys are predominantly distributed along the Southeastern shoulder of the Qinghai-Tibetan Plateau. Based on phylogenetic analyses of the mitochondrial cytochrome b gene (1143 bp) obtained from 23 specimens (eight species)

KARYOTYPE EVOLUTION OF SHREW MOLES (SORICOMORPHA: TALPIDAE)

The Chinese long-tailed mole (Scaptonyx fusicaudus) closely resembles American (Neurotrichus gibbsii) and Japanese (Dymecodon pilirostris and Urotrichus talpoides) shrew moles in size, appearance, and ecological habits, yet it has traditionally been classified either together with (viz subfamily Urotrichinae) or separately (tribe Scaptonychini) from the latter genera (tribe Urotrichini sensu lato). We explored the merit of these competing hypotheses by comparing the differentially stained karyotypes of S.fusicaudus and N. gibbsii with those previously reported for both Japanese taxa. With few exceptions, diploid chromosome number (2n = 34), fundamental autosomal number (FNa = 64), relative size, and G-banding pattern of S. fusicaudus were indistinguishable from those of D. pilirostris and U. talpoides. In fact, only chromosome 15 differed significantly between these species, being acrocentric in D. pilirostris, subtelocentric in U. talpoides, and metacentric in S. fusicaudus. This striking similarity is difficult to envisage except in light of a shared common ancestry, and is indicative of an exceptionally low rate of chromosomal evolution among these genera. Conversely, the karyotype of N. gibbsii deviates markedly in diploid chromosome and fundamental autosomal number (2n = 38 and FNa = 72, respectively), morphology, and G-banding pattern from those of Scaptonyx and the Japanese shrew moles. These differences cannot be explained by simple chromosomal rearrangements, and Suggest that rapid chromosomal reorganization Occurred ill the karyotype evolution of this species, possibly due to founder or bottleneck events.

Implications of changes in trophic diversity and food webs on fisheries and the environment

Most of the earth's ecosystems are experiencing slight to catastrophic losses of biodiversity, caused by habitat destruction, alien species introduction, climate change and pollution (Wilcove et al., 1998). These human effects have led to the extinction of native fish species, the collapse of their populations and the loss of ecological integrity and ecosystem functioning (Ogutu-Ohwayo & Hecky, 1991; Witte et al. , 1992a; Mills et al., 1994; Vitousek et al., 1996). Food webs are macro-descriptors of community feeding interactions that can be used to map the flow of materials and nutrients in ecosystems (Jepsen & Winemiller, 2002). Comparative food web studies have been used to address theoretical questions such as 'does greater trophic connectivity increase stability?' (Cohen et al., 1990), and 'does the number of trophic levels increase with productivity?' (Briand & Cohen, 1987). Answers to such questions have obvious applications for natural resources management. From a multi-species fisheries standpoint, there is a need to understand consumer-resource dynamics within complex trophic networks.

Potential risks of contaminants with specific reference to mercury

Fresh water and fish are important to the people who live in the Lake Victoria region therefore the quality of the water and fish is of major importance (Johnson & Odada, 1996). It is well known that dirty water and spoilt fish can lead to poor health and lower standards of living, and that quality can be affected by the pollution in the environment. Even though Lake Victoria is very large, it is relatively shallow and the water remains in the lake basin for a long time (Bootsma & Hecky, 1993). There are a number of environmental issues in Lake Victoria, including water hyacinth~over-population and increased farming causing problems with the lake ecosystem. All these factors combine to keep contaminants within the lake for long time, which will lead to gradually increasing concentrations in the lake. Pollution is a term that covers a wide variety of chemicals and physical changes and their adverse effects on the environment. Here we focus on contaminants, which are unwanted chemicals introduced to the environment. Contaminants include a very wide variety of chemicals, both man-made and natural, for example, mercury, pesticides and herbicides, heavy metals, and natural plant and algae toxins. Many contaminants do not always lead to adverse effects immediately, but can gradually induce long-term problems leading to chronic illnesses and physical damage. A few contaminants have very rapid impacts resulting in immediately obvious changes such as death or injury. Sources of contaminants are varied. Contaminants can get in the lake by the way of agricultural treatment of crops near the lake, industrial effluent, intentional introduction such as fish poisoning byfishermen, natural sources such as heavy metals from particular types of rocks, and even some plants naturally release their toxins. Contaminant sources are not always found near Lake Victoria.

Calculating transport AC losses in stacks of high temperature superconductor coated conductors with magnetic substrates using FEM

In this paper, the authors investigate the electromagnetic properties of stacks of high temperature superconductor (HTS) coated conductors with a particular focus on calculating the total transport AC loss. The cross-section of superconducting cables and coils is often modeled as a two-dimensional stack of coated conductors, and these stacks can be used to estimate the AC loss of a practical device. This paper uses a symmetric two dimensional (2D) finite element model based on the H formulation, and a detailed investigation into the effects of a magnetic substrate on the transport AC loss of a stack is presented. The number of coated conductors in each stack is varied from 1 to 150, and three types of substrate are compared: non-magnetic weakly magnetic and strongly magnetic. The non-magnetic substrate model is comparable with results from existing models for the limiting cases of a single tape (Norris) and an infinite stack (Clem). The presence of a magnetic substrate increases the total AC loss of the stack, due to an increased localized magnetic flux density, and the stronger the magnetic material, the further the flux penetrates into the stack overall. The AC loss is calculated for certain tapes within the stack, and the differences and similarities between the losses throughout the stack are explained using the magnetic flux penetration and current density distributions in those tapes. The ferromagnetic loss of the substrate itself is found to be negligible in most cases, except for small magnitudes of current. Applying these findings to practical applications, where AC transport current is involved, superconducting coils should be wound where possible using coated conductors with a non-magnetic substrate to reduce the total AC loss in the coil. © 2011 Elsevier B.V. All rights reserved.

Automatic object segmentation from calibrated images

This paper addresses the problem of automatically obtaining the object/background segmentation of a rigid 3D object observed in a set of images that have been calibrated for camera pose and intrinsics. Such segmentations can be used to obtain a shape representation of a potentially texture-less object by computing a visual hull. We propose an automatic approach where the object to be segmented is identified by the pose of the cameras instead of user input such as 2D bounding rectangles or brush-strokes. The key behind our method is a pairwise MRF framework that combines (a) foreground/background appearance models, (b) epipolar constraints and (c) weak stereo correspondence into a single segmentation cost function that can be efficiently solved by Graph-cuts. The segmentation thus obtained is further improved using silhouette coherency and then used to update the foreground/background appearance models which are fed into the next Graph-cut computation. These two steps are iterated until segmentation convergences. Our method can automatically provide a 3D surface representation even in texture-less scenes where MVS methods might fail. Furthermore, it confers improved performance in images where the object is not readily separable from the background in colour space, an area that previous segmentation approaches have found challenging. © 2011 IEEE.

Simulation studies on the magnetization of (RE)BCO bulk superconductors using various split-coil arrangements

Simulation studies were conducted on the magnetization of (RE)BCO (RE-Ba-Cu-O, where RE represents a rare earth element) bulk superconductors using various split-coil arrangements by solving the critical state equation using the commercial software FlexPDE. A pair of coaxial coils of identical size is identified as an optimum arrangement for practical magnetization at 77K by the zero-field cooling technique. In general, the magnetization process is likely to be most effective when the outer radius of the coils lies between 100% and 50% of the sample radius. A relatively large coil pair is necessary for samples with either a smaller aspect ratio or larger values of J c0. Two different regimes of flux penetration are found to be involved in the magnetization process. For a sufficiently small sample, the penetration field is determined by flux propagation from beneath the coil to the centre of the sample; for a sufficiently large sample, the definitive propagation route is from beneath the coil to the periphery of the sample. Effective split-coil magnetization occurs only in the former regime, and both penetration regimes are completely different from that involved in the solenoidal-coil magnetization process. © 2012 IOP Publishing Ltd.

Experimental studies of the quench behaviour of MgB2 superconducting wires for fault current limiter applications

Various MgB2 wires with different sheath materials provided by Hyper Tech Research Inc., have been tested in the superconducting fault current limiter (SFCL) desktop tester at 24-26K in a self-field. Samples 1 and 2 are similarly fabricated monofilamentary MgB2 wires with a sheath of CuNi, except that sample 2 is doped with SiC and Mg addition. Sample 3 is a CuNi sheathed multifilamentary wire with Cu stabilization and Mg addition. All the samples with Nb barriers have the same diameter of 0.83mm and superconducting fractions ranging from 15% to 27% of the total cross section. They were heat-treated at temperatures of 700 °C for a hold time of 20-40min. Current limiting properties of MgB2 wires subjected to pulse overcurrents have been experimentally investigated in an AC environment in the self-field at 50Hz. The quench currents extracted from the pulse measurements were in a range of 200-328A for different samples, corresponding to an average engineering critical current density (Je) of around 4.8 × 10 4Acm-2 at 25K in the self-field, based on the 1νVcm-1 criterion. This work is intended to compare the quench behaviour in the Nb-barrier monofilamentary and multifilamentary MgB2 wires with CuNi and Cu/CuNi sheaths. The experimental results can be applied to the design of fault current limiter applications based on MgB2 wires. © IOP Publishing Ltd.