Slot width augmentation in a slotted-wall transonic linear cascade wind tunnel

Transonic tests in linear cascade wind tunnels can suffer
from significant test section boundary interference effects in pitch. A slotted tailboard has been designed and optimised with an in-house Euler numerical method to reduce such ef- fects. Wind tunnel measurements on an overspeed Mach 1.27 discharge from a Rolls-Royce T2 cascade, featuring strong end-wall shock-induced interference, showed a 77% reduction in the flow pitchwise periodicity error with the optimised tail- board, with respect to the baseline open-jet cascade flow. Two-dimensional Euler predictions were also cross-validated against a three-dimensional Reynolds averaged computation, to explore the three-dimensionality of the discharge

Electrospun fibrous mats for skin and abdominal wall repair

Esta tese centra-se no desenvolvimento de materiais biodegradáveis e nãodegradáveis produzidos por eletrofiação com aplicação na área biomédica. O poli(3-hidroxibutirato-co-3-hidroxivalerato) (PHBV), um poliéster biodegradável, foi selecionado como base dos materiais biodegradáveis, enquanto o poli(tereftalato de etileno) (PET), um polímero sintético, estável e biocompatível, foi selecionado para a produção das matrizes não degradáveis. Adicionou-se quitosana aos sistemas com o objetivo de melhorar o processo de eletrofiação e as propriedades morfológicas, físico-químicas e biológicas dos materiais resultantes. A composição química, bem como as características morfológicas e físicoquímicas dos materiais em estudo, foram manipuladas de modo a otimizar a sua performance como suportes celulares para engenharia de tecidos. Foram realizados estudos in vitro com cultura de fibroblastos L929 para avaliar o comportamento das células, i.e. viabilidade, adesão, proliferação e morte, quando cultivadas nas matrizes produzidas por eletrofiação. Adicionalmente foram realizados ensaios in vivo para investigar o potencial dos materiais em estudo na regeneração cutânea e como tela abdominal. Os principais resultados encontrados incluem: o desenvolvimento de novas matrizes híbridas (PHBV/quitosana) adequadas ao crescimento de fibroblastos e ao tratamento de lesões de pele; o desenvolvimento de um sistema de eletrofiação com duas seringas para a incorporação de compostos bioativos; diversas estratégias para manipulação das características morfológicas dos materiais de PHBV/quitosana e PET/quitosana produzidos por eletrofiação; uma melhoria do conhecimento das interações fibroblastos-suporte polimérico; a verificação de uma resposta inflamatória desencadeada pelos materiais nãodegradáveis quando utilizados no tratamento de defeitos da parede abdominal, o que sugere a necessidade de novos estudos para avaliar a segurança do uso de biomateriais produzidos por eletrofiação.

Study of 19th century wall tiles for technical replicas development

O principal objectivo deste trabalho foi sistematizar características físico- químicas dos azulejos para conservação e restauro de fachadas azulejares da cidade de Ovar, pertencentes à fase produtiva da semi-industrialização e industrialização dos finais do século XIX inico do século XX, de forma a produzir réplicas técnicas para recolocação nos locais de fachada com lacunas de azulejo. Além de se ter criado uma base de dados sobre estes materiais, formularam-se réplicas para os corpos cerâmicos calcários e pó de pedra, sugerindo matérias-primas e grau de moagem para a sua formulação, pressão de prensagem, ciclo e temperaturas máximas de cozedura conferindo-lhes características técnicas para que estas possam ser aplicadas lado a lado com os azulejos seculares, sem que perturbem a unicidade técnica da fachada. Investigaram-se duas das patologias mais recorrentes que afectam o vidrado: destacamento por cristalização de sais e fendilhamento. A primeira afecta a perda da parte pictórica do azulejo, atirando-o para uma remoção compulsiva da fachada aquando da sua intervenção para conservação restauro. A segunda permite-nos compreender possíveis compromissos técnicos feitos no passado.

Hygrothermal performance of wood-hemp insulation in timber frame wall panels with and without a vapour barrier

An in situ experiment on a full-scale timber frame test building was carried out to study the hygrothermal performance of wood-hemp composite insulation in timber frame wall panels with and without a vapour barrier. The heat transfer properties and the likelihood of mould growth and condensation in the panels were compared. Step changes in the internal relative humidity were performed to explore the effects of high, normal and low internal moisture loads on the wall panels. No significant difference in the average equivalent thermal transmittance (U-values) between the panels with and without a vapour barrier was observed. The average equivalent U-values of the panels were close to the U-values calculated from the manufacturers’ declared thermal conductivity values of the insulation. The likelihood of condensation was higher at the interface of the wood-hemp insulation and the oriented strand board (OSB) in the panel without a vapour barrier. In terms of the parametric assessment of the mould germination potential, the relative humidity, the temperature and the exposure conditions in the insulation-OSB interfaces of the panel without a vapour barrier were found to be more favourable to the germination of mould spores. Nonetheless, when the insulations were dismantled, no mould was visually detected.

The comparative in situ hygrothermal performance of Hemp and Stone Wool insulations in vapour open timber frame wall panels

An in situ experiment in a full scale timber frame test building was carried out to compare the hygrothermal performance of Hemp and Stone Wool insulations of identical thermal conductivity. Hemp and Stone Wool insulations were installed in timber frame wall panels without vapour barrier. The comparison was made in terms of heat transfer properties, likelihood of mould growth and condensation. Step changes in internal relative humidity were performed to explore the effect of high and normal internal moisture load on the wall panels. No significant difference between the average equivalent thermal transmittance (U-values) of the panels incorporating Hemp and Stone Wool insulations was observed. The average equivalent U-values of the panels were closer to the calculated U-values of the panels based on the manufacturers’ declared thermal conductivity of Hemp and Stone Wool insulations. It was observed that the placement of heat flux sensor along the depth of the insulation had significant influence on the measured equivalent U-value of the panels during high internal moisture load. The frequency and likelihood of condensation was higher in the interface of Stone Wool and Oriented Strand Board (OSB). In terms of the parametric assessment of mould germination potential, relative humidity, temperature and exposure conditions in the insulation-OSB interfaces were found to be favourable to germination of mould spore. However, when the insulations were dismantled, no mould was visually detected.

Compte rendu: Jannis Androutsopoulos (dir.) (2014), Mediatization and sociolinguistic change, Berlin/Boston, De Gruyter, coll. « Linguae & litterae. Publications of the School of Language & Literature Freiburg Institute for Advanced Studies, 36 », vii-557 p. [ISBN : 978-3-11-034357-1]

Résumé non disponible

Kostenanalyse zur Digitalisierung von Herbarbelegen im Botanischen Garten/ Botanischen Museum in Berlin-Dahlem

Die vorliegende Arbeit ermittelt die Ist-Kosten für den Prozess der Herbarbeleg Digitalisierung im Botanischen Garten/ Botanischen Museum in Berlin-Dahlem. Dabei werden die Kosten durch drei verschiedene Vorgehensweisen aufgezeigt. Die erste Vorgehensweise ermittelt die Kosten für die Digitalisierung anhand der Gesamtaufwendungen im Botanischen Garten/ Botanischen Museum. In dieser Betrachtung werden die Kosten abgegrenzt, die nur der Digitalisierung zuzuordnen sind. Eine weitere Methode erfasst alle Einzelkosten die für die Digitalisierung von Herbarbelegen anfallen und stellt abschließend die Gesamtkosten für die Digitalisierung dar. Als weitere Vorgehensweise zur Kostenbestimmung wurde eine Projektbetrachtung gewählt. In dieser sind die Digitalisierungskosten anhand eines durchgeführten Projektes im Botanischen Garten/ Botanischen Museum veranschaulicht.

London Wall

London Wall is a physical manifestation of the invisible city all around us; a poetic snapshot of social networking traffic from within a three-mile radius of the Museum of London. Over a ten-day period, publicly available status updates from popular websites like twitter and facebook will be selected then published as a vast array of A3 posters pasted onto a wall in the museum's foyer, revealing the idle mutterings of ourselves to ourselves as a form of concrete poetry. This commission is in the foyer and is part of relaunch the museums new galleries.

Recycling old screen-printed electrodes with newly designed plastic antibodies on the wall of carbon nanotubes as sensory element for in situ detection of bacterial toxins in water

Using low cost portable devices that enable a single analytical step for screening environmental contaminants is today a demanding issue. This concept is here tried out by recycling screen-printed electrodes that were to be disposed of and by choosing as sensory element a low cost material offering specific response for an environmental contaminant. Microcystins (MCs) were used as target analyte, for being dangerous toxins produced by cyanobacteria released into water bodies. The sensory element was a plastic antibody designed by surface imprinting with carefully selected monomers to ensure a specific response. These were designed on the wall of carbon nanotubes, taking advantage of their exceptional electrical properties. The stereochemical ability of the sensory material to detect MCs was checked by preparing blank materials where the imprinting stage was made without the template molecule. The novel sensory material for MCs was introduced in a polymeric matrix and evaluated against potentiometric measurements. Nernstian response was observed from 7.24 × 10−10 to 1.28 × 10−9 M in buffer solution (10 mM HEPES, 150 mM NaCl, pH 6.6), with average slopes of −62 mVdecade−1 and detection capabilities below 1 nM. The blank materials were unable to provide a linear response against log(concentration), showing only a slight potential change towards more positive potentials with increasing concentrations (while that ofthe plastic antibodies moved to more negative values), with a maximum rate of +33 mVdecade−1. The sensors presented good selectivity towards sulphate, iron and ammonium ions, and also chloroform and tetrachloroethylene (TCE) and fast response (<20 s). This concept was successfully tested on the analysis of spiked environmental water samples. The sensors were further applied onto recycled chips, comprehending one site for the reference electrode and two sites for different selective membranes, in a biparametric approach for “in situ” analysis.

Insights into cell wall synthesis and cell division in Staphylococcus aureus

Dissertation presented to obtain the Ph.D degree in Biology

Regulation and function of the cell wall polymer lipoteichoic acid in staphylococcus aureus

A thesis submitted for the Degree of Master in Medical microbiology

Eco-wall modular solutions for buildings

This paper discusses the development of modular solutions for eco low-cost houses based on a pre-fabricated modular wall system environmentally sustainable, socioeconomically competitive and geared towards developing African nations with a housing deficit. The key point to the research of a modular wall solution is a structural layer complemented with local and materials made by non-specialized workforce. This wall also meets also hydrothermal acoustic and mechanical properties. Thus,the solution also offers good safety and interior comfort conditions to its users while maintaining the flexibility to expand the size of the house. Parameters as dimensions, materials and constructive processes of the existing housing stock were studied. Features such as the family size, typology, different uses, common materials, existing regulations, minimal living conditions, safety and comfort have also been considered to achieve the most efficient solution.

17-3-20, la révolution à Berlin, troupes révolutionnaires mettant leurs mitrailleuses en batterie : [photographie de presse] / [Agence Rol]

Référence bibliographique : Rol, 58541

17-3-20, révolution à Berlin, soldats avec mitrailleuses dans les rues de Berlin : [photographie de presse] / [Agence Rol]

Référence bibliographique : Rol, 58542