927 resultados para ALKYL BROMIDES
Resumo:
Dipyrromethene-Cu(II) derivatives possessing two dodecane alkyl chains have been used for the modification of gold electrodes. Electroactive host molecules have been incorporated into a lipophilic dodecanethiol SAM deposited onto gold electrodes through hydrophobic and van der Waals interactions (embedment technique). The presence of dipyrromethene-Cu(II) redox centers on the electrode surface was proved by cyclic voltammetry and Osteryoung square-wave voltammetry. The Au electrodes incorporating redox active Cu(II)-dipyrromethene SAMs were used for the direct voltammetric determination of paracetamol in human plasma.
Resumo:
N-alkyl-2,6-dimethyl-4(1H)-pyridinones, salts of 4-dimethylaminopyridine and 2-amino-5-nitropyridine are considered to be potential candidates for nonlinear optical (NLO) applications, in particular for the generation of blue-green laser radiation. Single crystals were grown following the slow evaporation technique at constant temperature. Single-shot laserinduced surface damage thresholds in the range 3–10 GW/cm2 were measured using a 18 ns Q-switched Nd:YAG laser. The surface morphologies of the damaged crystals were examined under an optical microscope and the nature of damage identified. The Vicker’s microhardness was determined at a load of 98.07 mN. The thermal transport properties, thermal diffusivity (α), thermal effusivity (e), thermal conductivity (K) and heat capacity (Cp), of the grown crystals were measured by an improved photopyroelectric technique at room temperature. All the results are presented and discussed.
Resumo:
The thesis deals with our studies on the synthesis and elucidation of structure of some metal complexes of dithio ligands, such as the dithiocarbamates, xanthates and 2-aminocyclopent-1-ene-1-dithiocarboxylate and its N-alkyl derivatives.2-Aminocyclopent-1-ene-1-dithiocarboxylate (ACDA) is an interesting ligand, because of its potential dual capability of bonding between the metal and the ligand. Since the earlier reports on the complexes of ACDA contain contradictory ideas on the nature of its bonding, it was thought worthwhile to undertake a detailed and systematic study of these type of complexes. As the ACDA complexes have very low solubilities in solvents like chloroform, we have used the isopropyl derivative of ACDA as the ligand. The increased solubility of these complexes have made it possible to investigate their NMR and solution electronic spectra.The complexes of this ligand have not yet been reported in the literature.We have synthesised some new mixed ligand complexes of dithiocarbamates by reacting bis(dithiocarbamato)-µ-dichloro dicopper complexes (obtained by the reaction of mixed benzoic dithiocarbamic anhydride and copper(II) chloride) with ACDA or its N-alkyl derivatives.Interactions of metal halides with the mixed anhydrides formed from benzoylchloride and xanthates have also been investigated. Novel complexes of the type, [Cu2(RXant)CI] (R=i-Bu, i-Pr, n-Bu or n-Pr)) have been isolated from the reaction of copper(II) chloride and the mixed anhydride, and these reactions appear to be like the clock reactions reported in the literature.It also deal with the characterisation of the complexes of the type [Hg(R2d t c )X] (X=Cl, Br or 1),[Cu3(R2dtc)6][Cu2Br6] and [Cu(R2dtc)Cl2](R2=Me2,Et2,Pip,Morph or Pyrr)respectively, synthesised by simple and novel routes, different from those reported earlier.
Resumo:
The present work is a base line attempt to investigate and assess the toxicities of three surfactants viz. anionic sodium dodecyl sulfate (SDS), non ionic Triton X-1OO (TX-IOO) and cationic cetyl trimethyl ammonium bromide (CTAB). These compounds represent simple members of the often neglected group of aquatic pollutants i.e. the anionic alkyl sulfates, non ionics and the cationics. These compounds are widely used In plastic industry, pesticide/herbicide formulations, detergents, oil spill dispersants, molluscicides etc. The test organisms selected for the present study are the cyanobacterium Synechocystis salina Wislouch representing a primary producer in the marine environment and a fresh water adapted euryhaline teleost Oreochromis mossambicus (peters) at the consumer level of the ecological pyramid. The fish species, though not indigenous to our country, is now found ubiquitously in fresh water systems and estuaries. Also it is highly resistant to pollutants and has been suggested as an indicator of pollution in tropical region .
Resumo:
The selective oxidation of alkylaromatics is one of the main processes since the reaction products are important as intermediates in numerous industrial organic chemicals. Side-chain oxidation of alkyl aromatic compounds catalyzed by heterogeneous catalysts using cleaner peroxide oxidants is an especially attractive goal since classical synthetic laboratory procedures preferably use permanganate or acid dichromate as stoichiometric oxidants. In spite of many studies, there are very few which use hydrogen peroxide as a source of oxygen in the C-H activation of alkanes. Eflective utilization of ethylbenzene, available in the xylene stream of the petrochemical industry to more value added products is a promising one in chemical industry. The oxidation products of ethylbenzene are widely employed as intermediates in organic, steroid and resin synthesis.
Resumo:
The objective of the present work is to improve the textural and structural properties of zeolite-Y through ion exchange with rare earth metals. We meant to obtain a comparative evaluation of the physicochemical properties and catalytic activity of rare earth modified H-Y, Na-Y, K-Y, and Mg-Y zeolites. Friedel-Crafts alkylations of benzene with higher 1- olefins such as 1-octene, 1-decene, and 1dodecene for the synthesis of linear alkylbenzene (LAB) have been selected for the present study. An attempt has also been directed towards the correlation of the enhancement in 2-phenylalkane formation to the improvement in the textural and structural properties upon rare earth modification for the zeolite-Y. The present method for LAB synthesis stands as an effective Green alternative for the existing hydrofluoric acid technology
Resumo:
Multi-component reactions are effective in building complex molecules in a single step in a minimum amount of time and with facile isolation procedures; they have high economy1–7 and thus have become a powerful synthetic strategy in recent years.8–10 The multicomponent protocols are even more attractive when carried out in aqueous medium. Water offers several benefits, including control over exothermicity, and the isolation of products can be carried out by single phase separation technique. Pyranopyrazoles are a biologically important class of heterocyclic compounds and in particular dihydropyrano[2,3-c]pyrazoles play an essential role in promoting biological activity and represent an interesting template in medicinal chemistry. Heterocyclic compounds bearing the 4-H pyran unit have received much attention in recent years as they constitute important precursors for promising drugs.11–13 Pyrano[2,3-c]pyrazoles exhibit analgesic,14 anti-cancer,15 anti-microbial and anti-inflammatory16 activity. Furthermore dihydropyrano[2,3-c]pyrazoles show molluscidal activity17,18 and are used in a screening kit for Chk 1 kinase inhibitor activity.19,20 They also find applications as pharmaceutical ingredients and bio-degradable agrochemicals.21–29 Junek and Aigner30 first reported the synthesis of pyrano[2,3-c]pyrazole derivatives from 3-methyl-1-phenylpyrazolin-5-one and tetracyanoethylene in the presence of triethylamine. Subsequently, a number of synthetic approaches such as the use of triethylamine,31 piperazine,32 piperidine,33 N-methylmorpholine in ethanol,34 microwave irradiation,35,36 solvent-free conditions,37–39 cyclodextrins (CDs),40 different bases in water,41 γ -alumina,42 and l-proline43 have been reported for the synthesis of 6-amino-4-alkyl/aryl-3-methyl- 2,4-dihydropyrano[2,3-c]pyrazole-5-carbonitriles. Recently, tetraethylammonium bromide (TEABr) has emerged as mild, water-tolerant, eco-friendly and inexpensive catalyst. To the best of our knowledge, quaternary ammonium salts, more specifically TEABr, have notbeen used as catalysts for the synthesis of pyrano[2,3-c]pyrazoles, and we decided to investigate the application of TEABr as a catalyst for the synthesis of a series of pyrazole-fused pyran derivatives via multi-component reactions
Resumo:
Durch asymmetrische Doppelbindungsisomerisierung mittels Me-DuPHOS-modifizierter Dihalogen-Nickel-Komplexe als Katalysatorvorstufen lassen sich aus 2-Alkyl-4,7-dihydro-1,3-dioxepinen hochenantiomerenreine 2-Alkyl-4,5-dihydro-1,3-dioxepine erhalten. Ein Ziel dieser Arbeit war es, die bisher noch unbekannte Absolutkonfiguration dieses Verbindungstyps zu bestimmen und darüber hinaus ihre Einsatzfähigkeit in der enantioselektiven organischen Synthese zu untersuchen. Zu diesem Zweck wurden enantiomerenangereichertes 2-Isopropyl- und 2-tert-Butyl-4,5-dihydro-1,3-dioxepin mit m-Chlorperbenzoesäure epoxidiert. Dabei bildeten sich die entsprechenden 3-Chlorbenzoesäure-(2-alkyl-5-hydroxy-1,3-dioxepan-4yl)-ester in hohen Ausbeuten und Diastereoselektivitäten. Von den vier zu erwartenden Diastereomeren wurden jeweils nur zwei mit einer Selektivität von mehr als 95:5 gebildet. Im Fall des 3-Chlorbenzoesäure-(2-isopropyl-5-hydroxy-1,3-dioxepan-4yl)-esters konnte das Haupt-diastereomer kristallin erhalten werden. Durch röntgenspektroskopische Untersuchung war es möglich, die Relativ-Konfiguration dieser Verbindung zu bestimmen. Die Ester lassen sich unter Ringverengung in 2-Alkyl-1,3-dioxan-4-carbaldehyde umlagern. Ausgehend von diesen Carbaldehyden stehen zwei Synthesewege zur Verfügung, welche zu Verbindungen führen deren Absolutkonfiguration bereits bekannt ist. So erhält man durch Reduktion 2-Alkyl-1,3-dioxan-4-yl-methanole, welche sich in 1,2,4-Butantriol überführen lassen. Oxidation ergibt die 2-Alkyl-1,3-dioxan-4-carbonsäuren, aus denen 3-Hydroxytetrahydrofuran-2-on gewonnen werden kann. Messung des Drehwertes dieser beiden literaturbekannten Verbindungen liefert nicht nur Information über deren Enantiomerenreinheit sondern ebenfalls über die Konfiguration ihres Stereozentrums. In Kombination mit der Relativ-Konfiguration des Esters ist somit ein Rückschluss auf die Absolutkonfiguration der eingesetzten 4,5-Dihydro-1,3-dioxepine möglich. Die auf den beschriebenen Wegen gewonnenen Substanzen finden Anwendung in der stereoselektiven organischen Synthese. Löst man die Chlorbenzoesäureester in Dichlormethan und behandelt sie mit wässriger Salzsäure, so entstehen die bicyclischen 2-Alkyltetrahydrofuro[2,3-d][1,3]dioxole. Auch bei diesen Verbindungen konnten hohe Enantio- und Diastereoselektivitäten erzielt werden. Der intermolekular verlaufende Reaktionsmechanismus der Bicyclus-Bildung, welcher unter Abspaltung eines den Alkylrest tragenden Aldehyds und dessen Neuanlagerung unter Ausbildung eines Acetals verläuft, konnte in dieser Arbeit durch ein Kreuzungsexperiment bestätigt werden. Umacetalisierung der Bicyclen liefert 2-Methoxytetrahydrofuran-3-ol, aus dem durch Acetalspaltung Tetrahydrofuran-2,3-diol erhalten wird, das die Halbacetalform der entsprechenden Desoxytetrose darstellt, die auf diese Weise in einer de novo-Synthese hergestellt werden kann.
Resumo:
Soil organic matter (SOM) vitally impacts all soil functions and plays a key role in the global carbon (C) cycle. More than 70% of the terrestric C stocks that participate in the active C cycle are stored in the soil. Therefore, quantitative knowledge of the rates of C incorporation into SOM fractions of different residence time is crucial to understand and predict the sequestration and stabilization of soil organic carbon (SOC). Consequently, there is a need of fractionation procedures that are capable of isolating functionally SOM fractions, i.e. fractions that are defined by their stability. The literature generally refers to three main mechanisms of SOM stabilization: protection of SOM from decomposition by (i) its structural composition, i.e. recalcitrance, (ii) spatial inaccessibility and/or (iii) interaction with soil minerals and metal ions. One of the difficulties in developing fractionation procedures for the isolation of functional SOM fractions is the marked heterogeneity of the soil environment with its various stabilization mechanisms – often several mechanisms operating simultaneously – in soils and soil horizons of different texture and mineralogy. The overall objective of the present thesis was to evaluate present fractionation techniques and to get a better understanding of the factors of SOM sequestration and stabilization. The first part of this study is attended to the structural composition of SOM. Using 13C cross-polarization magic-angle spinning (CPMAS) nuclear magnetic resonance (NMR) spectroscopy, (i) the effect of land use on SOM composition was investigated and (ii) examined whether SOM composition contributes to the different stability of SOM in density and aggregate fractions. The second part of the present work deals with the mineral-associated SOM fraction. The aim was (iii) to evaluate the suitability of chemical fractionation procedures used in the literature for the isolation of stable SOM pools (stepwise hydrolysis, treatments using oxidizing agents like Na2S2O8, H2O2, and NaOCl as well as demineralization of the residue obtained by the NaOCl treatment using HF (NaOCl+HF)) by pool sizes, 13C and 14C data. Further, (iv) the isolated SOM fractions were compared to the inert organic matter (IOM) pool obtained for the investigated soils using the Rothamsted Carbon Model and isotope data in order to see whether the tested chemical fractionation methods produce SOM fractions capable to represent this pool. Besides chemical fractionation, (v) the suitability of thermal oxidation at different temperatures for obtaining stable SOC pools was evaluated. Finally, (vi) the short-term aggregate dynamics and the factors that impact macroaggregate formation and C stabilization were investigated by means of an incubation study using treatments with and without application of 15N labeled maize straw of different degradability (leaves and coarse roots). All treatments were conducted with and without the addition of fungicide. Two study sites with different soil properties and land managements were chosen for these investigations. The first one, located at Rotthalmünster, is a Stagnic Luvisol (silty loam) under different land use regimes. The Ah horizons of a spruce forest and continuous grassland and the Ap and E horizons of two plots with arable crops (continuous maize and wheat cropping) were examined. The soil of the second study site, located at Halle, is a Haplic Phaeozem (loamy sand) where the Ap horizons of two plots with arable crops (continuous maize and rye cropping) were investigated. Both study sites had a C3-/C4-vegetational change on the maize plot for the purpose of tracing the incorporation of the younger, maize-derived C into different SOM fractions and the calculation of apparent C turnover times of these. The Halle site is located near a train station and industrial areas, which caused a contamination with high amounts of fossil C. The investigation of aggregate and density fractions by 13C CPMAS NMR spectroscopy revealed that density fractionation isolated SOM fractions of different composition. The consumption of a considerable part (10–20%) of the easily available O-alkyl-C and the selective preservation of the more recalcitrant alkyl-C when passing from litter to the different particulate organic matter (POM) fractions suggest that density fractionation was able to isolate SOM fractions with different degrees of decomposition. The spectra of the aggregate fractions resembled those of the mineral-associated SOM fraction obtained by density fractionation and no considerable differences were observed between aggregate size classes. Comparison of plant litter, density and aggregate size fractions from soil under different land use showed that the type of land use markedly influenced the composition of SOM. While SOM of the acid forest soil was characterized by a large content (> 50%) of POM, which contained high amounts of spruce-litter derived alkyl-C, the organic matter in the biologically more active grassland and arable soils was dominated by mineral-associated SOM (> 95%). This SOM fraction comprised greater proportions of aryl- and carbonyl-C and is considered to contain a higher amount of microbially-derived organic substances. Land use can alter both, structure and stability of SOM fractions. All applied chemical treatments induced considerable SOC losses (> 70–95% of mineral-associated SOM) in the investigated soils. The proportion of residual C after chemical fractionation was largest in the arable Ap and E horizons and increased with decreasing C content in the initial SOC after stepwise hydrolysis as well as after the oxidative treatments with H2O2 and Na2S2O8. This can be expected for a functional stable pool of SOM, because it is assumed that the more easily available part of SOC is consumed first if C inputs decrease. All chemical treatments led to a preferential loss of the younger, maize-derived SOC, but this was most pronounced after the treatments with Na2S2O8 and H2O2. After all chemical fractionations, the mean 14C ages of SOC were higher than in the mineral-associated SOM fraction for both study sites and increased in the order: NaOCl < NaOCl+HF ≤ stepwise hydrolysis << H2O2 ≈ Na2S2O8. The results suggest that all treatments were capable of isolating a more stable SOM fraction, but the treatments with H2O2 and Na2S2O8 were the most efficient ones. However, none of the chemical fractionation methods was able to fit the IOM pool calculated using the Rothamsted Carbon Model and isotope data. In the evaluation of thermal oxidation for obtaining stable C fractions, SOC losses increased with temperature from 24–48% (200°C) to 100% (500°C). In the Halle maize Ap horizon, losses of the young, maize-derived C were considerably higher than losses of the older C3-derived C, leading to an increase in the apparent C turnover time from 220 years in mineral-associated SOC to 1158 years after thermal oxidation at 300°C. Most likely, the preferential loss of maize-derived C in the Halle soil was caused by the presence of the high amounts of fossil C mentioned above, which make up a relatively large thermally stable C3-C pool in this soil. This agrees with lower overall SOC losses for the Halle Ap horizon compared to the Rotthalmünster Ap horizon. In the Rotthalmünster soil only slightly more maize-derived than C3-derived SOC was removed by thermal oxidation. Apparent C turnover times increased slightly from 58 years in mineral-associated SOC to 77 years after thermal oxidation at 300°C in the Rotthalmünster Ap and from 151 to 247 years in the Rotthalmünster E horizon. This led to the conclusion that thermal oxidation of SOM was not capable of isolating SOM fractions of considerably higher stability. The incubation experiment showed that macroaggregates develop rapidly after the addition of easily available plant residues. Within the first four weeks of incubation, the maximum aggregation was reached in all treatments without addition of fungicide. The formation of water-stable macroaggregates was related to the size of the microbial biomass pool and its activity. Furthermore, fungi were found to be crucial for the development of soil macroaggregates as the formation of water-stable macroaggregates was significantly delayed in the fungicide treated soils. The C concentration in the obtained aggregate fractions decreased with decreasing aggregate size class, which is in line with the aggregate hierarchy postulated by several authors for soils with SOM as the major binding agent. Macroaggregation involved incorporation of large amounts maize-derived organic matter, but macroaggregates did not play the most important role in the stabilization of maize-derived SOM, because of their relatively low amount (less than 10% of the soil mass). Furthermore, the maize-derived organic matter was quickly incorporated into all aggregate size classes. The microaggregate fraction stored the largest quantities of maize-derived C and N – up to 70% of the residual maize-C and -N were stored in this fraction.
Resumo:
Relativistic self-consistent charge Dirac-Slater discrete variational method calculations have been done for the series of molecules MBr_5, where M = Nb, Ta, Pa, and element 105, Ha. The electronic structure data show that the trends within the group 5 pentabromides resemble those for the corresponding pentaclorides with the latter being more ionic. Estimation of the volatility of group 5 bromides has been done on the basis of the molecular orbital calculations. According to the results of the theoretical interpretation HaBr_5 seems to be more volatile than NbBr_5 and TaBr_5.
Resumo:
Für die Entwicklung selbstorganisierter Monoschichten (SAMs) auf Gold(111)-Oberflächen wurden neue, redox-funktionalisierte Schwefel-Tripodliganden synthetisiert. Um die tripodale Struktur zu realisieren, wurde Adamantan als vierbindiges Zentrum eingesetzt. Die Anbindung an die Goldoberfläche wurde durch Thioethereinheiten ermöglicht, eventuelle laterale Wechselwirkungen durch Alkylseitenketten an den Thioethereinheiten, sowie durch lineare, rigide Spacereinheiten wurden untersucht. Als redoxaktive, funktionelle Einheit wurde ein Ferrocenylrest an den Liganden eingeführt. Gebildete monomolekulare Filme der Liganden auf Gold wurden mit Hilfe von Röntgenphotoelektronenspektroskopie (XPS), Nahkanten-Reflexions-Röntgenabsorptionsspektroskopie (NEXAFS) und Sum-Frequency-Generation (SFG) charakterisiert, um die Filmqualität, die Bindung ans Substrat und Orientierungsordnung im Film zu ermitteln.
Resumo:
Aziridine, Stickstoffanaloga der Epoxide, können regio- und stereoselektive Ringöffnungsreaktionen eingehen, wodurch ihnen als „building blocks“ in der Organischen Synthese eine große Bedeutung zukommt. In dieser Arbeit wurden unterschiedliche N-Aminoverbindungen synthetisiert sowie die Anwendungsmöglichkeit dieser Hydrazinderivate als Stickstoffquellen in Aziridinierungen von Olefinen untersucht. In der vorliegenden Dissertation wurde eine neue Methode zur Darstellung von N-Aminosuccinimid entwickelt und die Einsatzmöglichkeit als Stickstoffquelle in Aziridinierungsreaktionen in einer Reihe von Umsetzungen mit funktionalisierten ebenso wie mit nicht-funktionalisierten Olefinen demonstriert. Die ableitbaren Aziridine wurden hierbei in Ausbeuten von bis zu 80 % erhalten. In der Aziridinierungsreaktion von N-Aminosuccinimid mit 4,7-Dihydro-2-isopropyl-1,3-dioxepin resultieren bicyclische Aziridinierungsprodukte, die als endo/exo-Isomere in einem 1:1-Verhältnis anfallen. Es ist in dieser Arbeit gelungen, die Isomere in guten Ausbeuten zu erhalten, sie säulenchromatographisch zu trennen und ihre Konfiguration im festen Zustand mittels Kristallstrukturanalyse eindeutig zu bestimmen. Enantiomerenangereicherte Olefine, wie z. B. in 2-Position alkylsubstituierte 5-Methyl-4H-1,3-dioxine mit Enantiomerenüberschüssen von 92% ee liefern in der Aziridinierung mit N-Aminosuccinimid und Iodosylbenzol ein 4-Methyl-1,3-oxazolidin-4-carbaldehydderivat in einer zweistufigen Reaktion- der Aziridinierung und einer Umlagerung- ein 4-Methyl-1,3-oxazolidin-4-carbaldehydderivat. Für die Diastereoselektivität des Aziridinierungsschrittes wurde 65 % de bestimmt. In einer neuen Synthese über zwei Stufen ausgehend von (+)-3,4-Dimethoxysuccinanhydrid konnte ein chiraler Stickstoffüberträger - (+)-N-Amino-3,4-dimethoxysuccinimid - in Ausbeuten bis zu 86 % synthetisiert. Die Umsetzung dieser optisch aktiven Stickstoffquelle mit einer Vielzahl prochiraler Alkene führt zu diastereomeren Aziridinen in Ausbeuten bis zu 65% und Diastereoselektivitäten von bis zu 66% de. Anhand ausgewählter Verbindungen konnten die Absolutkonfigurationen der Reaktionsprodukte mittels Kristallstrukturanalyse eindeutig geklärt werden.
Resumo:
The aim of this work was to produce a variety of fluorescent diatom cell wall material as a basis for spectroscopic investigations of the influence of the photonic structure on the emission of an incorporated laser dye. This goal was achieved by the method of in vivo-fluorochromation, in which the fluorescence dyes are incorporated by the diatom cells during cell wall formation. Several fluorescent dyes (mostly rhodamines) known as strong laser dyes, were tested for a possible application within this method. The results of this work show that half of the tested rhodamines can be applied for an in vivo-fluorochromation of diatom cells. For a successful incorporation into the diatom cell wall, a relatively low toxicity to diatom cells is necessary. Replacement of the carbon acid function at the carboxyphenyl ring of the rhodamine by a methyl or ethylester function showed to convert a rhodamine of relatively low toxicity to a rhodamine leading to severe lethal effects within the cells. In contrast to their carbon acid forms, which posses a net neutral charge of the molecule, rhodamine esters exhibit a net positive charge. The enhanced toxicological effects seem to be due to an increased accumulation of positive charged rhodamines within the mitochondria, an increased hydrophobicity due to the attachment of an alkyl substituent, an increased retention time of the dyes within the mitochondria and a therefore stronger negative effect on the mitochondrial membrane bound energy processes of the diatom cell. Therefore rhodamines with a positive net charge deriving from a methyl or ethylester function at the carboxy phenyl ring instead of a carbon acid substituent showed not to be suitable for long-term investigations/ biomineralization studies of diatoms. Investigations performed on diatom species of different orders showed that rhodamine 19, rhodamine B, and rhodamine 101 can presumably be successfully applied for in vivo-fluorochromation to all diatom species. The results obtained here can help to find further laser dyes for an in vivo-fluorochromation of diatom cells and therefore for the production of fluorescent nanostructural elements for a detailed optical investigation of the diatom cell wall. First optical measurements performed on in vivo-fluorochromated cell walls did not give any hints concerning the photonic structure of the diatom cell. Cell wall parts with different nanostructural elements were investigated and by comparison of the obtained fluorescence emission spectra, no special features that might derive from photonic structural effects could be observed. Results concerning the concentration dependent shifts within the emission spectra, as well as the decrease of fluorescence intensity of the stained cell wall structures with increasing dye concentration, depict that several effects occurring by interaction of the molecules within the cell wall can have an impact on the technical application of fluorescent cell walls. It can be assumed that the investigation of the photonic crystal behaviour and the possibility to achieve laser action within the diatom cell wall can be hampered by molecular interactions. The results give hints to prevent such obstacles. Comparison of the recent findings and state of the art of in vivo-fluorochromation of diatom cell wall material, make clear that the here presented results are of importance and can offer a considerable contribution to the development and establishment of new biosilification markers, for diatoms as well as for other biosilifying organisms.
Resumo:
Mit dieser Arbeit wurde die Selbstassemblierung von dia- und paramagnetischen Molekülen sowie Einzelmolekülmagneten auf Goldsubstraten und magnetisch strukturierten Substraten untersucht. Dazu wurden drei verschiedene Klassen an Phthalocyaninderivaten verwendet: Diamagnetische Subphthalocyanine, paramagnetische Phthalocyaninatometalle und Diphthalocyaninatolanthanidkomplexe. Alle synthetisierten Verbindungen sind peripher thioethersubstituiert. Die Alkylketten (a: n-C8H17, b: n-C12H25) vermitteln die Löslichkeit in vielen organischen Solventien und sorgen für eine geordnete Assemblierung auf einer Oberfläche, wobei die Bindung auf Gold hauptsächlich über die Schwefelatome stattfindet. Die aus Lösung abgeschiedenen selbstassemblierten Monolagen wurden mit XPS, NEXAFS-Spektroskopie und ToF-SIMS untersucht. Bei der Selbstassemblierung auf magnetisch strukturierten Substraten stehen die Moleküle unter dem Einfluss magnetischer Streufelder und binden bevorzugt nur in bestimmten Bereichen. Die gebildeten Submonolagen wurden zusätzlich mit X-PEEM untersucht. Die erstmals dargestellten Manganphthalocyanine [MnClPc(SR)8] 1 wurden ausgehend von MnCl2 erhalten. Hier fand bei der Aufarbeitung an Luft eine Oxidation zu Mangan(III) statt; +III ist die stabilste Oxidationsstufe von Mangan in Phthalocyaninen. Der Nachweis des axialen Chloridoliganden erfolgte mit Massenspektrometrie und FIR- sowie Raman-Spektroskopie. SQUID-Messungen haben gezeigt, dass die Komplexe 1 vier ungepaarte Elektronen haben. Bei den Subphthalocyaninen [BClSubpc(SR)6] 2 wurde der axiale Chloridoligand mit dem stäbchenförmigen Phenolderivat 29-H substituiert und die erfolgreiche Ligandensubstitution durch NMR- und IR-Spektroskopie sowie Massenspektrometrie an den Produkten [BSubpc(SR)6(29)] 30 belegt. Der Radikalcharakter der synthetisierten Terbiumkomplexe [Tb{Pc(SR)8}2] 3 wurde spektroskopisch nachgewiesen; SQUID-Messungen ergaben, dass es sich um Einzelmolekülmagnete mit einer Energiebarriere U des Doppelpotentialtopfs von 880 K oder 610 cm-1 bei 3a handelt. Zunächst wurden die SAMs der Komplexverbindungen 1, 2, 30 und 3 auf nicht magnetisch strukturierten Goldsubstraten untersucht. Die Manganphthalocyanine 1 bilden geordnete SAMs mit größtenteils flach liegenden Molekülen, wie die XPS-, NEXAFS- und ToF-SIMS-Analyse zeigte. Die Mehrzahl der Thioether-Einheiten ist auf Gold koordiniert und die Alkylketten zeigen ungeordnet von der Oberfläche weg. Bei der Adsorption findet eine Reduktion zu Mangan(II) statt und der axiale Chloridoligand wird abgespalten. Das beruht auf dem sog. Oberflächen-trans-Effekt. Im vorliegenden Fall übt die Metalloberfläche einen stärkeren trans-Effekt als der axiale Ligand aus, was bisher experimentell noch nicht beobachtet wurde. Die thioethersubstituierten Subphthalocyanine 2 und 30 sowie die Diphthalocyaninatoterbium-Komplexe 3 sind ebenfalls für SAMs geeignet. Ihre Monolagen wurden mit XPS und NEXAFS-Spektroskopie untersucht, und trotz einer gewissen Unordnung in den Filmen liegen die Moleküle jeweils im Wesentlichen flach auf der Goldoberfläche. Vermutlich sind bei diesen Systemen auch die Alkylketten größtenteils parallel zur Oberfläche orientiert. Im Gegensatz zu den Manganphthalocyaninen 1 tritt bei 2b, 30a, 30b und 3b neben der koordinativen Bindung der Schwefelatome auf Gold auch eine für Thioether nicht erwartete kovalente Au–S-Bindung auf, die durch C–S-Bindungsbruch unter Abspaltung der Alkylketten ermöglicht wird. Der Anteil, zu dem dieser Prozess stattfindet, scheint nicht mit der Molekülstruktur zu korrelieren. Selbstassemblierte Submonolagen auf magnetisch strukturierten Substraten wurden mit dem diamagnetischen Subphthalocyanin 2b hergestellt. Der Nachweis der Submonolagen war schwierig und gelang schließlich durch eine Kombination von ToF-SIMS, NEXAFS Imaging und X-PEEM. Die Analyse der ToF-SIMS-Daten zeigte, dass tatsächlich eine Modulation der Verteilung der Moleküle auf einem unterwärts magnetisch strukturierten Substrat eintritt. Mit X-PEEM konnte die magnetische Struktur der ferromagnetischen Schicht des Substrats direkt der Verteilung der adsorbierten Moleküle zugeordnet werden. Die Subphthalocyanine 2b adsorbieren nicht an den Domänengrenzen, sondern vermehrt dazwischen. Auf Substraten mit abwechselnd 6.5 und 3.5 µm breiten magnetischen Domänen binden die Moleküle bevorzugt in den Bereichen geringster magnetischer Streufeldgradienten, also den größeren Domänen. Solche Substrate wurden für die ToF-SIMS- und X-PEEM-Messungen verwendet. Bei größeren magnetischen Strukturen mit ca. 400 µm breiten Domänen, wie sie aufgrund der geringeren Ortsauflösung dieser Methode für NEXAFS Imaging eingesetzt wurden, binden die Moleküle dann in allen Domänen. Die diamagnetischen Moleküle werden nach dieser Interpretation aus dem inhomogenen Magnetfeld über der Probenoberfläche heraus gedrängt und verhalten sich analog makroskopischer Diamagnete. Die eindeutige Detektion der Moleküle auf den magnetisch strukturierten Substraten konnte bisher nur für die diamagnetischen Subphthalocyanine 2b erfolgen. Um die Interpretation ihres Verhaltens bei der Selbstassemblierung in einem inhomogenen Magnetfeld weiter voranzutreiben, wurde das Subphthalocyanin 37b dargestellt, welches ein stabiles organisches TEMPO-Radikal in seinem axialen Liganden enthält. Das paramagnetische Subphthalocyanin 37b sollte auf den magnetisch strukturierten Substraten in Regionen starker magnetischer Streufelder binden und damit das entgegengesetzte Verhalten zu den diamagnetischen Subphthalocyaninen 2b zeigen. Aus Zeitgründen konnte dieser Nachweis im Rahmen dieser Arbeit noch nicht erbracht werden.
Resumo:
We report on a new class of nonionic, photosensitive surfactants consisting of a polar di(ethylene oxide) head group attached to an alkyl spacer of between two and eight methylene groups, coupled through an ether linkage to an azobenzene moiety. Structural changes associated with the interconversion of the azobenzene group between its cis and trans forms as mediated by the wavelength of an irradiating light source cause changes in the surface tension and self-assembly properties. Differences in saturated surface tensions (surface tension at concentrations above the CMC) were as high as 14.4 mN/m under radiation of different wavelengths. The qualitative behavior of the surfactants changed as the spacer length changed, attributed to the different orientations adopted by the different surfactants depending on their isomerization states, as revealed by neutron reflection studies. The self-assembly of these photosensitive surfactants has been investigated by light scattering, small angle neutron scattering, and cryo-TEM under different illuminations. The significant change in the self-assembly in response to different illumination conditions was attributed to the sign change in Gaussian rigidity, which originated from the azobenzene photoisomerization.