907 resultados para removal experiment
Resumo:
The aim of this study was to evaluate the persistence of methacrylate-based cement residues on the dentin, after dentin surface cleaning with ethanol or acetone, with or without previous application of a dentin adhesive. Forty bovine crown fragments were obtained and the dentin surface was washed with 1.0 mL of 2.5% sodium hypochlorite (NaOCl), followed by 0.1 mL of 17% ethylenediaminetetraacetic acid application for 3 min, and final irrigation with 2.5% NaOCl. The specimens were air dried and resin-based cement was rubbed onto the dentine surface with a microbrush applicator. In 20 specimens, previously to cement, a dentin adhesive was applied in all surfaces. After 15 min, the surface was scrubbed with a cotton pellet and moistened with ethanol or acetone, compounding the following groups: G199.5% ethanol and G2acetone, without previous use of dentin adhesive; G399.5% ethanol and G4acetone, with previous use of dentin adhesive. The dentin surface was scrubbed until the cement residues could not be visually detected. Sections were then processed for scanning electron microscopy and evaluated at 500x magnification and scores were attributed to each image according to the area covered by residual sealer, and data were subjected to KruskalWallis at 5% significance. The lower residue presence was observed in G3 (P = 0.005). All surface presented cement residues when acetone was used as cleaning solution (P = 0.0005). The cleaning solutions were unable to completely remove the cement residues from both surfaces. The ethanol used after previous application of the dentin adhesive promoted the lower presence of residues.
Resumo:
The aim of this study was to evaluate the persistence of resin cement residues after dentin surface cleaning with different alcohol-based solutions or an essential oil (eucalyptol). Forty bovine teeth were sectioned in order to expose pulp chamber dentin to be washed with 1.0 mL of 2.5% sodium hypochlorite (NaOCl), followed by 0.1 mL of 17% EDTA application for 3 min, and final irrigation with 2.5% NaOCl. The specimens were air dried and resin-based cement was rubbed onto the dentine surface with a microbrush applicator. After 15 min, the surface was scrubbed with a cotton pellet and moistened with different dentin cleaning solutions, compounding the following groups: G195% ethanol, G270% ethanol, G370% isopropyl alcohol, or G4eucalyptol. The dentin was scrubbed until the cement residues could not be visually detected. Sections were then processed for SEM and evaluated at x 500 magnification. Scores were attributed to each image according to the area covered by residual sealer, and data were subjected to KruskalWallis at 5% significance. Eucalyptol promoted the most adequate dentin cleaning, although no statistical difference was detected amongst the groups (P > 0.05), except between the eucalyptol and 70% ethanol groups (P < 0.05). All the evaluated dentin cleaning solutions were unable to completely remove the cement residues from the dentin surface. Microsc. Res. Tech., 2012. (C) 2012 Wiley Periodicals, Inc.
Resumo:
Portuguese chestnut (Castanea sativa) is used for forest products, raw nuts and processed flour, paste, and candy. We studied the influence on germination efficiency of seed with and without partial tegument removal combined with different substrate composition (coconut fiber, pine compost and vermiculite) at São Paulo State University, Campus of Botucatu, São Paulo, Brazil. Randomized blocks were used in a factorial scheme 3x2 (three substrates x two seed types) consisting of six treatments with five replications (twelve seeds). Seeds were sowed in expanded polystyrene trays, with 72 cells, and maintained at 25 C under controlled environment. Rate, time elapsed and speed of seed germination was submitted to ANOVA and the average compared using Tukey's 5% test of probability and curves adjusted based on Gompertz regression. Coconut fiber or vermiculite associated with seed without partial tegument removal showed the highest germination rate, and coconut fiber with or without partial tegument removal displayed the fastest speed of seed germination.
Resumo:
Avaliaram-se os efeitos da remoção temporária de bezerros (RTB) ou da aplicação de gonadotrofina coriônica eqüina (eCG) na taxa de prenhez (TP) de vacas Nelore lactantes tratadas com um dispositivo intravaginal liberador de progesterona (DILP). No experimento 1, 83 vacas Nelore e 102 mestiças (Nelore × Red Angus) foram distribuídas em três grupos. em dia aleatório do ciclo estral (D0), os animais do grupo 1 foram tratados com benzoato de estradiol (BE; 2,5 mg, IM, Estrogin®) e um DILP (1 g de progesterona, DIB®), removido no D9, quando também se administrou d-cloprostenol (150 µg, IM, Prolise®) e aproximadamente 12 horas após identificação do estro realizou-se a inseminação artificial. No grupo 2 (IATF), o tratamento foi semelhante ao aplicado no grupo 1, porém, administrou-se uma segunda dose de benzoato de estradiol (1 mg) no D10 e 30-36 horas mais tarde realizou-se a inseminação artificial em tempo fixo (IATF). No grupo 3 (IATF/RTB), os bezerros foram removidos a partir do D9 até a inseminação artificial com tempo fixo (IATF). As taxas de prenhez para as vacas Nelore e mestiças foram, respectivamente, de 7,69 e 41% (Controle); 23,52 e 59,57% (IATF); 69,44 e 55,81% (IATF/RTB). No experimento 2, 255 vacas Nelore lactantes foram distribuídas em três grupos. Os animais do grupo 4 (IATF) foram tratados com benzoato de estradiol (2 mg) e um DILP (1,9 g de progesterona, CIDR-B®) no D0 e no D8 sofreram remoção do DILP no D8 e administração de 25 mg de dinoprost (IM, Lutalyse®). No D9, foi aplicado benzoato de estradiol (1 mg) realizando-se a IATF 30-36 horas mais tarde. No grupo 5 (IATF/RTB), os bezerros foram removidos no D9 até a IATF. O grupo 6 (eCG) foi semelhante ao IATF, exceto pela aplicação de eCG no D9 (400 UI, IM, Novormon®). As taxas de prenhez foram de 50,57 (IATF), 53,57 (IATF/RTB) e 54,76% (eCG). A associação de RTB ao tratamento hormonal com DILP aumenta as taxas de prenhez, enquanto a adição de eCG ao tratamento não melhora as taxa de prenhez de vacas Nelore lactantes ciclando e em boa condição corporal.
Resumo:
The photoelectrochemical degradation of p-nitrophenol (PNP) was investigated using titanium dioxide thin-film photoelectrode. The effects of different supporting electrolytes, pH, applied potential and PNP concentration were examined and discussed. Complete photodegradation was obtained in perchlorate medium at pH 2 when the photoanode was biased at +1.0 V (versus SCE) during a 3-h experiment. Under these conditions, carbon removal of approximately 60% was achieved. (C) 2005 Elsevier B.V. All rights reserved.
Resumo:
The present study analyzed the composition of the aquatic fauna associated to the mangrove forest in a southeastern Brazilian river. The composition of the macrofauna in the roots of the marginal vegetation located at three different salinity stretches was analyzed by sampling pieces of the submerged branches of the vegetation (natural substrate) and pieces of sisal rope (artificial substrate), installed close to the natural vegetation and sampled after a period of 14 colonization days. In both types of substrate, twelve taxonomic groups were sampled, representing three phyla (Cnidaria, Annelida and Arthropoda). The crustaceans, corresponding to the most diversified group, were represented by Copepoda, Tanaidacea, Isopoda, Amphipoda and Decapoda. The highest salinity stretch showed the highest abundance, with a progressive decrease from high to low salinity for both substrates. Copepoda and Tanaidacea predominated on both substrates, although the artificial substrate exhibited the highest total abundance and species richness. Considering the relative abundance of the taxonomic groups on both substrates, the majority of groups predominated in the highest salinity range. Significant differences on the longitudinal distribution of abundance were associated to the variation on salinity and with the complexity of the substrate.
Resumo:
With the development of the textile industry, there has been a demand for dye removal from contaminated effluents. In recent years, attention has been directed toward various natural solid materials that are capable of removing pollutants from contaminated water at low cost. One such material is sugarcane bagasse. The aim of the present study was to evaluate adsorption of the dye Acid Violet Alizarin N with different concentrations of sugarcane bagasse and granulometry in agitated systems at different pH. The most promising data (achieved with pH 2.5) was analyzed with both Freundlich and Langmuir isotherms equations. The model that better fits dye adsorption interaction into sugarcane bagasse is Freundlich equation, and thus the multilayer model. Moreover, a smaller bagasse granulometry led to greater dye adsorption. The best treatment was achieved with a granulometry value lower than 0.21 mm at pH 2.50, in which the total removal was estimated at a concentration of 16.25 mg mL(-1). Hence, sugarcane bagasse proves to be very attractive for dye removal from textile effluents.
Resumo:
Ants frequently harvest seeds from faeces of frugivorous vertebrates. By transporting these seeds to nests, ants may influence seed dispersal success of plants. Seed removal by ants from vertebrate faeces is influenced by the seed species involved. Faeces from different vertebrates differ in chemical composition and physical characteristics. It remains unclear, however, whether the faeces itself affects the ant-seed interaction. In this study experimental seed-containing faecal portions were prepared using defecations of birds, marsupials, and monkeys and seeds of two aroids (Philodendron corcovadense and P. ppendiculatum, Araceae) and one liana species (Schlegelia parviflora, Bignoniaceae). Faecal portions were arranged along a transect established in the understory of a lowland rainforest in southeast Brazil. For P. appendiculatum the probability of detection and the proportion of seeds removed were identical between marsupial and monkey faeces. For P. corcovadense and S. parviflora, the probability of detection was affected by seed species and, apparently, also by the interaction between seed species and type of faeces (P = 0.097), but not by the type of faeces itself (bird or monkey). Both factors (i.e., seed species and type of faeces) affected the proportion of seeds removed (faeces type was marginally significant; P = 0.08), whereas the interaction between them was not significant. The results indicate that seed species affects seed removal by ants, while the type of faeces probably interacts with seed traits to influence faeces detection.
Resumo:
Testou-se o efeito do arilo na germinação de M. champaca em condições controladas, bem como na sua remoção, em ambiente natural. Os ensaios de germinação foram mantidos a 25 ± 2 °C, sob luz branca constante. Os experimentos de remoção foram levados a cabo em três talhões velhos (idades de 39 a 62 anos) e três novos (15 anos de idade) de eucalipto mantidos no Horto Florestal Navarro de Andrade, em Rio Claro, SP. Os resultados indicaram que o arilo inibe a germinação, sendo as sementes fotoblásticas positivas. Observou-se que a remoção de sementes foi maior em talhões velhos do que em novos, provavelmente devido à maior densidade de roedores nos talhões velhos. Nos talhões novos, verificou-se que formigas removiam mais sementes ariladas. Esses insetos são importantes agentes na remoção do arilo de sementes derrubadas por pássaros, promovendo, assim, aumento na germinação e evitando a possível predação das sementes por roedores.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)
Resumo:
This work deals with noise removal by the use of an edge preserving method whose parameters are automatically estimated, for any application, by simply providing information about the standard deviation noise level we wish to eliminate. The desired noiseless image u(x), in a Partial Differential Equation based model, can be viewed as the solution of an evolutionary differential equation u t(x) = F(u xx, u x, u, x, t) which means that the true solution will be reached when t ® ¥. In practical applications we should stop the time ''t'' at some moment during this evolutionary process. This work presents a sufficient condition, related to time t and to the standard deviation s of the noise we desire to remove, which gives a constant T such that u(x, T) is a good approximation of u(x). The approach here focused on edge preservation during the noise elimination process as its main characteristic. The balance between edge points and interior points is carried out by a function g which depends on the initial noisy image u(x, t0), the standard deviation of the noise we want to eliminate and a constant k. The k parameter estimation is also presented in this work therefore making, the proposed model automatic. The model's feasibility and the choice of the optimal time scale is evident through out the various experimental results.
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Invertebrate predation on zooplankton was investigated in mesocosms in the shallow tropical Lake Monte Alegre, Sauo Paulo State, Brazil, in the summer of 1999. Two treatments were applied: one with natural densities of prey and the predators Chaoborus brasiliensis and the water mite Krendowskia sp. (Pr+), and another without predators (Pr-). Three enclosures (volume: 6.6 m(3) of water per enclosure) per treatment were installed in the sediment of the deepest area of the lake (5.0 m). At the beginning, Chaoborus larvae were present in Pr- enclosures, because of technical difficulties in preventing their entrance, but they virtually disappeared in the course of the experiment. Water mites were almost absent in Pr- enclosures. Chaoborus predation negatively influenced the Daphnia gessneri population, but not the populations of the copepods Tropocyclops prasinus and Thermocyclops decipiens and the rotifers Keratella spp. Death rates of Daphnia were generally significantly higher in the Pr+ treatment; Daphnia densities increased after the disappearance of Chaoborus in Pr-. Copepod losses to predation in the experiment may be compensated by higher fecundity, shorter egg development time, and lower pressure on egg-bearing females, resulting in a lower susceptibility to Chaoborus predation. The predation impact of water mite on microcrustaceans and rotifers in the experiment was negligible.
Resumo:
Objectives: To evaluate the influence of different protocols for resin cement removal during cementation on biofilm formation.Methods: Twenty-eight ceramic blocks, which were injected under pressure, were placed over enamel blocks obtained from freshly extracted bovine incisors. The ceramic blocks were cemented to the enamel blocks using a dual-cured resin cement and the excess resin was removed according to the experimental group: TS: Teflon spatula; BR: brush; BR+: brush and polishing; SB+: scalpel blade and polishing. After autoclaving, the samples were colonised by incubation in a sucrose broth suspension standardised with Streptococcus mutans in microaerophilic stove. Specimens were quantitatively analysed for bacterial adherence at the adhesive interface using confocal laser scanning microscopy and counting the colony forming units, and qualitatively analysed using SEM. The roughness (Ra/Rz/RSm) was also analysed. Data were analysed by 1-way ANOVA and Tukey's test (5%).Results: The roughness values ranged from 0.96 to 1.69 mu m for Ra (p > 0.05), from 11.59 to 22.80 mu m for Rz (p = 0.02 < 0.05) and from 293.2 to 534.3 mu m for RSm (p = 0.00). Bacterial adhesion varied between 1,974,000 and 2,814,000 CFU/ml (p = 0.00). Biofilm mean thickness ranged from 0.477 and 0.556 mu m (p > 0.05), whilst the biovolume values were between 0.388 and 0.547 mu m(3)/mu m(2) (p = 0.04). Lower values for roughness, bacterial adhesion, biofilm thickness and biovolume were found with BR, whilst TS presented the highest values for most of the parameters. SEM images confirmed the quantitative values.Conclusions: The restoration margin morphology and interface roughness affects bacterial accumulation. The brush technique promoted less bacterial colonisation at the adhesive interface than did the other removal methods.Clinical significance: The brush technique seems to be a good option for removing the excess resin cement after adhesive cementation in clinical practice, as indicated by its better results with lower bacterial colonisation. (C) 2012 Elsevier Ltd. All rights reserved.