Analysis of phasor measurement method in tracking the power frequency of distorted signals

This paper presents an analysis of phasor measurement method for tracking the fundamental power frequency to show if it has the performance necessary to cope with the requirements of power system protection and control. In this regard, several computer simulations presenting the conditions of a typical power system signal especially those highly distorted by harmonics, noise and offset, are provided to evaluate the response of the Phasor Measurement (PM) technique. A new method, which can shorten the delay of estimation, has also been proposed for the PM method to work for signals free of even-order harmonics.

Failure analysis of engineering systems with preventive maintenance and failure interactions

Optimal operation and maintenance of engineering systems heavily rely on the accurate prediction of their failures. Most engineering systems, especially mechanical systems, are susceptible to failure interactions. These failure interactions can be estimated for repairable engineering systems when determining optimal maintenance strategies for these systems. An extended Split System Approach is developed in this paper. The technique is based on the Split System Approach and a model for interactive failures. The approach was applied to simulated data. The results indicate that failure interactions will increase the hazard of newly repaired components. The intervals of preventive maintenance actions of a system with failure interactions, will become shorter compared with scenarios where failure interactions do not exist.

Load on osseointegrated fixation of a transfemoral amputee during a fall : loading, descent, impact and recovery analysis

Falling represents a health risk for lower limb amputees fitted with an osseointegrated fixation mainly because of the potential damage to the fixation. The purpose of this study was to characterise a real forward fall that occurred inadvertently to a transfemoral amputee fitted with an osseointegrated fixation while attending a gait measurement session to assess the load applied on the residuum. The objective was to analyse the load applied on the fixation with an emphasis on the sequence of events, the pattern and the magnitude of the forces and moments. The load was measured directly at 200 Hz using a six-channel transducer. Complementary video footage was also studied. The fall was divided into four phases: loading (240 ms), descent (620 ms), impact (365 ms) and recovery (2495 ms). The main impact forces and moments occurred 870 ms and 915 ms after the heel contact, and corresponded to 133 %BW and 17 %BWm, or 1.2 and 11.2 times the maximum forces and moments applied during the previous steps of the participant, respectively. This study provided key information to engineers and clinicians facing the challenge to design equipment, and rehabilitation and exercise programs to restore safely the locomotion of lower limb amputees.

Extending life-cycle costing (LCC) analysis for sustainability considerations in road infrastructure projects

Sustainable development is about making societal investments. These investments should be in synchronization with the natural environment, trends of social development, as well as organisational and local economies over a long time span. Traditionally in the eyes of clients, project development will need to produce the required profit margins, with some degrees of consideration for other impacts. This is being changed as all citizens of our society are becoming more aware of concepts and challenges such as the climate change, greenhouse footprints, and social dimensions of sustainability, and will in turn demand answers to these issues in built facilities. A large number of R&D projects have focused on the technical advancement and environmental assessment of products and built facilities. It is equally important address the cost/benefit issue, as developers in the world would not want to loose money by investing in built assets. For infrastructure projects, due to its significant cost of development and lengthy delivery time, presenting the full money story of going green is of vital importance. Traditional views of life-cycle costing tend to focus on the pure economics of a construction project. Sustainability concepts are not broadly integrated with the current LCCA in the construction sector. To rectify this problem, this paper reports on the progress to date of developing and extending contemporary LCCA models in the evaluation of road infrastructure sustainability. The suggested new model development is based on sustainability indicators identified through previous research, and incorporating industry verified cost elements of sustainability measures. The on-going project aims to design and a working model for sustainability life-cycle costing analysis for this type of infrastructure projects.

Campylobacter jejuni and campylobacter coli genotyping by high-resolution melting analysis of a flaA fragment

The highly variable flagellin-encoding flaA gene has long been used for genotyping Campylobacter jejuni and Campylobacter coli. High-resolution melting (HRM) analysis is emerging as an efficient and robust method for discriminating DNA sequence variants. The objective of this study was to apply HRM analysis to flaA-based genotyping. The initial aim was to identify a suitable flaA fragment. It was found that the PCR primers commonly used to amplify the flaA short variable repeat (SVR) yielded a mixed PCR product unsuitable for HRM analysis. However, a PCR primer set composed of the upstream primer used to amplify the fragment used for flaA restriction fragment length polymorphism (RFLP) analysis and the downstream primer used for flaA SVR amplification generated a very pure PCR product, and this primer set was used for the remainder of the study. Eighty-seven C. jejuni and 15 C. coli isolates were analyzed by flaA HRM and also partial flaA sequencing. There were 47 flaA sequence variants, and all were resolved by HRM analysis. The isolates used had previously also been genotyped using single-nucleotide polymorphisms (SNPs), binary markers, CRISPR HRM, and flaA RFLP. flaAHRManalysis provided resolving power multiplicative to the SNPs, binary markers, and CRISPR HRM and largely concordant with the flaA RFLP. It was concluded that HRM analysis is a promising approach to genotyping based on highly variable genes.

An analysis of cyclists crashes to identify ITS-based intervention

Cycling provides a number of health and environmental benefits. However, cyclists are more likely to suffer serious injury or be killed in traffic accidents than car drivers and the estimated cost of crashes in Australia is $1.25AU billion per year. Current interventions to reduce bicycle crashes include compulsory helmet use, media campaigns, and the provision of cycling lanes, as well as road user education and training. It is difficult to assess the effectiveness of current interventions as there is no accurate measure of cyclist exposure in South East Queensland (SEQ). This paper analyses cyclist crash characteristics in Queensland with the view to identifying appropriate Intelligent Transport Systems (ITS) based intervention to reduce cyclist injury and death. The inappropriateness of some ITS interventions to improve cyclist safety is highlighted and a set of ITS interventions are identified, based on Queensland crash data 2002-2006.

Power system stability analysis based on descriptive study of electrical indices

In a power network, when a propagation energy wave caused by a disturbance hits a weak link, a reflection is appeared and some of energy is transferred across the link. In this work, an analytical descriptive methodology is proposed to study the dynamical stability of a large scale power system. For this purpose, the measured electrical indices (angle, or voltage/frequency) following a fault in different points among the network are used, and the behaviors of the propagated waves through the lines, nodes and buses are studied. This work addresses a new tool for power system stability analysis based on a descriptive study of electrical measurements. The proposed methodology is also useful to detect the contingency condition and synthesis of an effective emergency control scheme.

A regulatory analysis of international climate change regulation

The political challenges impeding the negotiation of a comprehensive multilateral agreement on international climate change have received a great deal of attention. A question that has gone somewhat overlooked is what essential components an effective regulatory scheme to reduce greenhouse gas emissions should contain. The objective of this article is to examine the regulatory architecture of current international arrangements relating to global climate change regulation. A systematic analysis of the structure, substantive composition, and administrative characteristics of the UNFCCC and Kyoto Protocol is undertaken. The analytical standard against which the agreements are examined is whether current international regulatory arrangements satisfy the basic requirements of regulatory coherence. The analysis identifies how the present scheme consists of a complex institutional structure that lacks a substantive regulatory core. The implications of the absence of functional and effective mechanisms to govern greenhouse gas emission reductions are considered in relation to the principles of good regulatory design. This, in turn, provides useful insights into how a better regulatory scheme might be designed.

Strategic information systems research : an archival analysis

The Journal of Strategic Information Systems (JSIS) has been an international outlet for Information Systems research that focuses on strategic issues since 1991. This paper reports on an analysis of the research published in JSIS to date. The paper presents a preliminary classification system for research topics related to Strategic Information Systems into which all 316 JSIS research papers as at end 2009 are classified. Discussion on changing emphases in topics over time is provided, in the context of the editorial philosophy of the journal. The paper seeks to stimulate discussion on future directions for research in Strategic Information Systems.

Demographic category membership and leadership in small groups : a social identity analysis

Developing the social identity theory of leadership (e.g., [Hogg, M. A. (2001). A social identity theory of leadership. Personality and Social Psychology Review, 5, 184–200]), an experiment (N=257) tested the hypothesis that as group members identify more strongly with their group (salience) their evaluations of leadership effectiveness become more strongly influenced by the extent to which their demographic stereotype-based impressions of their leader match the norm of the group (prototypicality). Participants, with more or less traditional gender attitudes (orientation), were members, under high or low group salience conditions (salience), of non-interactive laboratory groups that had “instrumental” or “expressive” group norms (norm), and a male or female leader (leader gender). As predicted, these four variables interacted significantly to affect perceptions of leadership effectiveness. Reconfiguration of the eight conditions formed by orientation, norm and leader gender produced a single prototypicality variable. Irrespective of participant gender, prototypical leaders were considered more effective in high then low salience groups, and in high salience groups prototypical leaders were more effective than less prototypical leaders. Alternative explanations based on status characteristics and role incongruity theory do not account well for the findings. Implications of these results for the glass ceiling effect and for a wider social identity analysis of the impact of demographic group membership on leadership in small groups are discussed.

The Revised Transactional Model (RTM) of occupational stress and coping : an improved process approach

Despite more than three decades of research, there is a limited understanding of the transactional processes of appraisal, stress and coping. This has led to calls for more focused research on the entire process that underlies these variables. To date, there remains a paucity of such research. The present study examined Lazarus and Folkman’s (1984) transactional model of stress and coping. One hundred and twenty nine Australian participants with full time employment (i.e. nurses and administration employees) were recruited. There were 49 male (age mean = 34, SD = 10.51) and 80 female (age mean = 36, SD = 10.31) participants. The analysis of three path models indicated that in addition to the original paths, which were found in Lazarus and Folkman’s transactional model (primary appraisal-->secondary appraisal-->stress-->coping), there were also direct links between primary appraisal and stress level time one and between stress level time one to stress level time two. This study has provided additional insights into the transactional process which will extend our understanding of how individuals appraise, cope and experience occupational stress.

Critical discourse analysis and political economy of communication : understanding the new corporate order

This article uses critical discourse analysis to analyse material shifts in the political economy of communications. It examines texts of major corporations to describe four key changes in political economy: (1) the separation of ownership from control; (2) the separation of business from industry; (3) the separation of accountability from responsibility; and (4) the subjugation of ‘going concerns’ by overriding concerns. The authors argue that this amounts to a political economic shift from traditional concepts of ‘capitalism’ to a new ‘corporatism’ in which the relationships between public and private, state and individual interests have become redefined and obscured through new discourse strategies. They conclude that the present financial and regulatory ‘crisis’ cannot be adequately resolved without a new analytic framework for examining the relationships between corporation, discourse and political economy.

What shapes player performance in soccer? Empirical findings from a panel analysis

In this article, we investigate the pay-performance relationship of soccer players using individual data from eight seasons of the German soccer league Bundesliga. We find a nonlinear pay-performance relationship, indicating that salary does indeed affect individual performance. The results further show that player performance is affected not only by absolute income level but also by relative income position. An additional analysis of the performance impact of team effects provides evidence of a direct impact of team-mate attributes on individual player performance.

An analysis of the determinants of job satisfaction when individuals' baseline satisfaction levels may differ.

A growing literature seeks to explain differences in individuals' self-reported satisfaction with their jobs. The evidence so far has mainly been based on cross-sectional data and when panel data have been used, individual unobserved heterogeneity has been modelled as an ordered probit model with random effects. This article makes use of longitudinal data for Denmark, taken from the waves 1995-1999 of the European Community Household Panel, and estimates fixed effects ordered logit models using the estimation methods proposed by Ferrer-i-Carbonel and Frijters (2004) and Das and van Soest (1999). For comparison and testing purposes a random effects ordered probit is also estimated. Estimations are carried out separately on the samples of men and women for individuals' overall satisfaction with the jobs they hold. We find that using the fixed effects approach (that clearly rejects the random effects specification), considerably reduces the number of key explanatory variables. The impact of central economic factors is the same as in previous studies, though. Moreover, the determinants of job satisfaction differ considerably between the genders, in particular once individual fixed effects are allowed for.

Dynamics of transformation and fragmentation of composite liquid nano-particles

Recent research on particle size distributions and particle concentrations near a busy road cannot be explained by the conventional mechanisms for particle evolution of combustion aerosols. Specifically they appear to be inadequate to explain the experimental observations of particle transformation and the evolution of the total number concentration. This resulted in the development of a new mechanism based on their thermal fragmentation, for the evolution of combustion aerosol nano-particles. A complex and comprehensive pattern of evolution of combustion aerosols, involving particle fragmentation, was then proposed and justified. In that model it was suggested that thermal fragmentation occurs in aggregates of primary particles each of which contains a solid graphite/carbon core surrounded by volatile molecules bonded to the core by strong covalent bonds. Due to the presence of strong covalent bonds between the core and the volatile (frill) molecules, such primary composite particles can be regarded as solid, despite the presence of significant (possibly, dominant) volatile component. Fragmentation occurs when weak van der Waals forces between such primary particles are overcome by their thermal (Brownian) motion. In this work, the accepted concept of thermal fragmentation is advanced to determine whether fragmentation is likely in liquid composite nano-particles. It has been demonstrated that at least at some stages of evolution, combustion aerosols contain a large number of composite liquid particles containing presumably several components such as water, oil, volatile compounds, and minerals. It is possible that such composite liquid particles may also experience thermal fragmentation and thus contribute to, for example, the evolution of the total number concentration as a function of distance from the source. Therefore, the aim of this project is to examine theoretically the possibility of thermal fragmentation of composite liquid nano-particles consisting of immiscible liquid v components. The specific focus is on ternary systems which include two immiscible liquid droplets surrounded by another medium (e.g., air). The analysis shows that three different structures are possible, the complete encapsulation of one liquid by the other, partial encapsulation of the two liquids in a composite particle, and the two droplets separated from each other. The probability of thermal fragmentation of two coagulated liquid droplets is discussed and examined for different volumes of the immiscible fluids in a composite liquid particle and their surface and interfacial tensions through the determination of the Gibbs free energy difference between the coagulated and fragmented states, and comparison of this energy difference with the typical thermal energy kT. The analysis reveals that fragmentation was found to be much more likely for a partially encapsulated particle than a completely encapsulated particle. In particular, it was found that thermal fragmentation was much more likely when the volume ratio of the two liquid droplets that constitute the composite particle are very different. Conversely, when the two liquid droplets are of similar volumes, the probability of thermal fragmentation is small. It is also demonstrated that the Gibbs free energy difference between the coagulated and fragmented states is not the only important factor determining the probability of thermal fragmentation of composite liquid particles. The second essential factor is the actual structure of the composite particle. It is shown that the probability of thermal fragmentation is also strongly dependent on the distance that each of the liquid droplets should travel to reach the fragmented state. In particular, if this distance is larger than the mean free path for the considered droplets in the air, the probability of thermal fragmentation should be negligible. In particular, it follows form here that fragmentation of the composite particle in the state with complete encapsulation is highly unlikely because of the larger distance that the two droplets must travel in order to separate. The analysis of composite liquid particles with the interfacial parameters that are expected in combustion aerosols demonstrates that thermal fragmentation of these vi particles may occur, and this mechanism may play a role in the evolution of combustion aerosols. Conditions for thermal fragmentation to play a significant role (for aerosol particles other than those from motor vehicle exhaust) are determined and examined theoretically. Conditions for spontaneous transformation between the states of composite particles with complete and partial encapsulation are also examined, demonstrating the possibility of such transformation in combustion aerosols. Indeed it was shown that for some typical components found in aerosols that transformation could take place on time scales less than 20 s. The analysis showed that factors that influenced surface and interfacial tension played an important role in this transformation process. It is suggested that such transformation may, for example, result in a delayed evaporation of composite particles with significant water component, leading to observable effects in evolution of combustion aerosols (including possible local humidity maximums near a source, such as a busy road). The obtained results will be important for further development and understanding of aerosol physics and technologies, including combustion aerosols and their evolution near a source.