Theoretical investigation on the one- and two-photon absorption properties for a series of symmetrical charge transfer fluorene-phenylene and fluorene-thiophene derivatives

One- and two-photon absorption properties of a series of fluorene derivatives with symmetrical charge transfer D-IT-D and A-IT-A structural motifs have been theoretically investigated with ZINDO/S method. The optimized structures and the characterization of frontier molecular orbitals were obtained by using AMI calculations. Two-photon absorption properties of molecules have been studied using three-state model. The calculation results have shown that fluorene-thiophene derivatives exhibit larger two-photon absorption cross-section as compared with other studied molecules. To illustrate the results, the crucial effects of thiophene ring on fluorenethiophene derivatives and the net charge changes on the pi-conjugated bridges are analyzed theoretically. (c) 2006 Elsevier B.V. All rights reserved.

星载激光相干测高计的参量设计

为使星载激光高度计实现高空间分辨力、高距离精度,提出了联合采用调频光纤激光器和相干测距的方法。详细讨论了这种方法的实现方案,并对方案中的激光发射功率、望远镜口径以及脉冲宽度对距离精度及信噪比的影响进行数值模拟。对系统参量进行分析,得到了相关参量的关系和优化的参量。结果表明,当望远镜口径为400 mm时,啁啾调频速率为1 MHz/μs,脉冲时间宽度150~350μs,发射功率10 W左右时,基于相干测距的星载激光高度计可以实现距离精度小于15 cm的技术指标。

高重复率紧凑型微脉冲全固态激光器

本文设计并实现了一台高重复率，紧凑型微脉冲全固态激光器。YAG晶体， Nd:YAG晶体和Cr4+:YAG晶体键合为一个单块晶体作为谐振腔。优化计算了Cr4+:YAG晶体的初始透过率，耦合输出透射率和泵浦光斑大小。对激光器的性能进行了测试，结果表明该激光器适合于空间激光测距。

基于正交频率变换的高功率蓝绿全固态激光器

对多横模全固态激光器使用正交频率变换进行了分析,计算了频率转换效率与激光发散角的关系。使用双KTP晶体正交倍频的方法,对Nd∶YAG激光器输出的含有高阶横模的激光进行倍频实验研究。在1064 nm Nd∶YAG激光基波功率密度为121 MW/cm2时,其谐波转换效率达到75.5%。研究表明,对于光束质量较差的基波激光,采用正交频率变换的方式,适当选择晶体参数,同样可以获得较高效率的二次谐波输出。

高重复频率、窄脉宽全固态光纤放大器种子源

高重复频率、窄脉宽的全固态激光器种子源级联光纤放大器是获得高功率脉冲激光输出的有效手段.短上能态寿命的Nd∶YVO4晶体在连续抽运、高重复频率Q开关工作时容易得到接近连续性能的平均输出功率.理论分析了声光(AO)调Q器件中影响输出能量和脉宽大小的主要因素,优化配置了腔型参数.利用激光二极管(LD)光纤耦合模块端面抽运Nd∶YVO4晶体,实现了声-光调Q重复频率100 kHz以上,脉宽20 ns以下,波长1064 nm的激光输出.在抽运功率5.7 W时,得到了脉宽15.3 ns,重复频率150 kHz的种子光输出,在级联单级光纤放大器后,得到了20 W的输出.

星载激光对水下目标通信可行性研究

The characteristics of media in communication channel are analyzed briefly and the reasonable optical parameters of media are adopted. With certain communication system parameters the temporal and spatial distributions of the received signal from submerged platform are simulated using Monte Carlo method. The upper limit of the ratio of Monte Carlo estimated error to averaged value is about 0.3%. From the simulated results, the optimized sampling timing of receiver and field of view of telescope are obtained. Also the signal-to-noise ratio of the receiver is calculated. Based on this, the error probability of the communication system is deduced from laser pulse position modulation and maximum likelihood detection. The results show that under severe environment robust laser communication from a satellite to a submerged platform can be achieved.

Output beam quality of edge pumped planar waveguide lasers with confocal unstable resonators

Output beam quality of edge pumped planar waveguide lasers with confocal unstable resonators is investigated by diffraction methods, taking into account gain saturation, asymmetric pumping, and beam interaction. The influences of pumping uniformity, doping concentration, cavity length and effective Fresnel number are analyzed with respect to output beam quality and pumping efficiency. It is found that good beam quality and high efficiency can be obtained with asymmetric pumping and optimized negative branch confocal unstable resonators. (c) 2005 The Optical Society of Japan.

The intensity distribution and thermal stability of InnoSlab laser

Partially end-pumped slab laser is an innovative solid state laser, namely InnoSlab. Combining the hybrid resonator with partially end-pumping, the output power can be scaled with high beam quality. In this paper, the output intensity distributions are simulated by coordinate transformation fast Fourier transform (FFT) algorithm, comparing the thermal lens influence. As the simulated curves showed, the output mode is still good when the thermal lens effect is strong, indicating the good thermal stability of InnoSlab laser. Such a new kind of laser can be designed and optimized on the base of this simulation.

色散管理孤子传输特性分析

色散管理孤子光波系统的色散图周期由具有正负色散值的两段光纤组成，并且在系统中周期性放置集中放大器及滤波器装置。采用变分法获得了描述此种系统性能的常微分方程组，并利用这组方程数值研究了各种参量对孤子传输性能的影响。研究结果表明，虽然从整体趋势上看，当要求色散管理孤子有较好的稳定性时，应适当降低系统的色散管理强度，但在一定条件下，调整光纤放大器的位置以及正负色散光纤的色散差值，可同时获得相对较大的色散管理强度和好的孤子稳定性；总体来讲，集总放大器的位置会对孤子传输的稳定性、色散管理孤子的能量增强因子、脉冲最佳

Beam quality improvement of laser diode array by using off-axis external cavity

A novel off-axis external cavity is designed for laser diode array to improve the beam quality. In this external cavity, a circle aperture with variable size is used as a spatial filter. The diameter of aperture is optimized to 1.2mm and the off-axis angle of external cavity is optimized at 2.6 deg. In the optimal case, the beam parameter product (BPP) of laser diode array is reduced to 121 mm. mrad from 1050 mm. mrad with external cavity optical efficiency of 81%. (C) 2007 Optical Society of America.

硬边非稳腔平面波导激光器的光束特性

基于衍射理论和坐标变换,采用数值模拟的方法分析了硬边非稳腔平面波导激光器的光束特性,研究了存在非均匀抽运和增益饱和时,输出激光的光束质量.在端面抽运和边缘抽运时,比较了正支和负支非稳腔的输出光束特性.结果表明：利用优化的离轴硬边非稳腔可以得到近衍射极限的输出.在相同的抽运不均匀性情况下,对于边缘抽运和端面抽运,正支非稳腔的光束质量因子M^2分别为3.9和2.3,而相同条件下负支非稳腔的M^2因子为1.8和1.7.

注入锁定激光器的边带锁频技术稳频系统优化分析

介绍了边带锁频技术稳频方法，推导出鉴频曲线，对稳频控制过程进行了分析．建立了注入锁定激光器的边带锁频技术稳频系统理论模型，讨论了相关参量对稳频效果的影响并且进行了优化．结果表明，增加入射光强，采用窄线宽的法布里一珀罗以及对法布里一珀罗进行高准确度温控都可以增强稳频效果．提出适用于注入锁定激光器的两种稳频方案并进行比较．

Skate elektriko baten gauzatzea, hautabideak eta diseinua.

[EU]Lan honetan hutsetik hasita skate motorizatu baten diseinu bat egin da, Industria Teknologian Ingeniaritzako Graduan eskuratutako jakintzak erabiliz. Skatea gazteengan oso erabilia den garraiobide bat da aisia dela-eta, eta sinpletasuna eta ekonomia kontuan hartuta, aisia eta ingurugiroarekiko konpromisoa nahasten dira diseinu honekin. Lanak bide argi bat dauka: hasieran merkatuaren egoera aztertzen da, gero diseinu posible batzuk proposatu ahal izateko, eta hortik aukera bat jorratu ahal izateko. Hortaz, prozesua hasieratik hasita, egitura hau izango du lanak: Hasteko, skate motorizatuen merkatuko egoera zein den aztertzen da, ondoren eta helburuak zeintzuk diren kontutan izanda, diseinu posible batzuk proposatu ahal izateko, alternatiben analisien atalean ageri direnak. Proposamen horiek aztertu egiten dira, alde on eta txarrak desberdinduz eta horietako soluzio bat aukeratuz. Aukeratutako diseinuaren CAD modelo bat eraikitzen da, ondoren egoera fisikoa matematikoki modelizatzeko eta beharrezko kalkuluak egin ahal izateko, metodologia atalean eta eranskinetan ageri direnak, hala nola, azelerazio jakin bat lortzeko behar den potentzia, transmisioan beharrezkoak diren kalkuluak kokatu beharreko elementuak zeintzuk diren erabaki ahal izateko, etab. Bide honetan, jorraturiko diseinuaz gain beste diseinu optimizatu eta konplexuago bat proposatzen da, ikerketa bidea zabalik duena, enpresa mundura gehiago zuzendua. Azkenik, lana burutzeko bete behar izan diren ataza bakoitzaren deskribapena eta iraupena, aurrekontua eta gastu aitorpena, arriskuen analisia eta proiektu honetatik atera ditugun ondorioak ematen dira.

Efficient excitations of radially and azimuthally polarized Nd 3+:YAG ceramic microchip laser by use of subwavelength multilayer concentric gratings composed of Nb2O5/SiO2

Cylindrical vector beams were produced from laser diode end-pumped Nd:YAG ceramic microchip laser by use of two types of subwavelength multilayer gratings as the axisymmetric-polarization output couplers respectively. The grating mirrors are composed of high- and low-refractive-index (Nb2O5/SiO2) layers alternately while each layer is shaped into triangle and concentric corrugations. For radially polarized laser output, the beam power reached 610mW with a polarization extinction ratio ( PER) of 61: 1 and a slope efficiency of 68.2%; for azimuthally polarized laser output, the beam power reached 626mW with a PER of 58: 1 and a slope efficiency of 47.6%. In both cases, the laser beams had near-diffraction limited quality. Small differences of beam power, PER and slope efficiency between radially and azimuthally polarized laser outputs were not critical, and could be minimized by further optimized adjustment to laser cavity and the reflectances of respective grating mirrors. The results manifested, by use of the photonic crystal gratings mirrors and end-pumped microchip laser configuration, CVBs can be generated efficiently with high modal symmetry and polarization purity. (C) 2008 Optical Society of America.

Diseño, Modelado y Análisis por Elementos Finitos de un Cuadro de Bicicleta de Carretera.

[ES]El objetivo de este proyecto es llevar a cabo el diseño conceptual, modelado y análisis estructural de un cuadro de bicicleta de geometría de carretera, empleando herramientas de Diseño Asistido por Ordenador y software de Análisis con Elementos Finitos. El modelo inicial será analizado y optimizado de cara a que cumpla los requerimientos resitentes del escenario de cargas asumido. El propósito de este proyecto es completar la primera fase de un hipotético caso de producción.