A swirler stabilized combustion chamber for a micro-gas turbine fuelled with natural gas

Micro-gas turbines are a good alternative for on-site power generation, since their operation is very reliable. The possibility of operating with various fuels increases versatility and, as a result, the usage of these devices. Focusing on a performance improvement of a tri-fuel low-cost micro-gas turbine, this work presents investigations of the inner flow of its combustion chamber. The aim of this analysis was the characterization of the flame structure by the temperature field of the chamber inner flow. The chamber was fuelled with natural gas. In the current chamber, a swirler and a reversed flow configuration were utilized to provide flame stabilization. The inner flow investigations were done with numerical analysis, which were compared to experimental data. The analysis of the inner flow was done with numerical simulations, which used the RSM turbulence model. A β-PDF equilibrium model was adopted to account for the turbulent combustion process. Different models of heat transfer were compared. Thermal radiation and specially heat conduction in the liner walls played significant roles on results.

Human thermal comfort: an irreversibility-based approach emulating empirical clothed-body correlations and the conceptual energy balance equation

Exergetic analysis can provide useful information as it enables the identification of irreversible phenomena bringing about entropy generation and, therefore, exergy losses (also referred to as irreversibilities). As far as human thermal comfort is concerned, irreversibilities can be evaluated based on parameters related to both the occupant and his surroundings. As an attempt to suggest more insights for the exergetic analysis of thermal comfort, this paper calculates irreversibility rates for a sitting person wearing fairly light clothes and subjected to combinations of ambient air and mean radiant temperatures. The thermodynamic model framework relies on the so-called conceptual energy balance equation together with empirical correlations for invoked thermoregulatory heat transfer rates adapted for a clothed body. Results suggested that a minimum irreversibility rate may exist for particular combinations of the aforesaid surrounding temperatures. By separately considering the contribution of each thermoregulatory mechanism, the total irreversibility rate rendered itself more responsive to either convective or radiative clothing-influenced heat transfers, with exergy losses becoming lower if the body is able to transfer more heat (to the ambient) via convection.

Metabolic and thermodynamic responses to dehydration-induced reductions in muscle blood flow in exercising humans

[EN] 1. The present study examined whether reductions in muscle blood flow with exercise-induced dehydration would reduce substrate delivery and metabolite and heat removal to and from active skeletal muscles during prolonged exercise in the heat. A second aim was to examine the effects of dehydration on fuel utilisation across the exercising leg and identify factors related to fatigue. 2. Seven cyclists performed two cycle ergometer exercise trials in the heat (35 C; 61 +/- 2 % of maximal oxygen consumption rate, VO2,max), separated by 1 week. During the first trial (dehydration, DE), they cycled until volitional exhaustion (135 +/- 4 min, mean +/- s.e.m.), while developing progressive DE and hyperthermia (3.9 +/- 0.3 % body weight loss and 39.7 +/- 0.2 C oesophageal temperature, Toes). On the second trial (control), they cycled for the same period of time maintaining euhydration by ingesting fluids and stabilising Toes at 38.2 +/- 0.1 degrees C. 3. After 20 min of exercise in both trials, leg blood flow (LBF) and leg exchange of lactate, glucose, free fatty acids (FFA) and glycerol were similar. During the 20 to 135 +/- 4 min period of exercise, LBF declined significantly in DE but tended to increase in control. Therefore, after 120 and 135 +/- 4 min of DE, LBF was 0.6 +/- 0.2 and 1.0 +/- 0.3 l min-1 lower (P < 0.05), respectively, compared with control. 4. The lower LBF after 2 h in DE did not alter glucose or FFA delivery compared with control. However, DE resulted in lower (P < 0.05) net FFA uptake and higher (P < 0.05) muscle glycogen utilisation (45 %), muscle lactate accumulation (4.6-fold) and net lactate release (52 %), without altering net glycerol release or net glucose uptake. 5. In both trials, the mean convective heat transfer from the exercising legs to the body core ranged from 6.3 +/- 1.7 to 7.2 +/- 1.3 kJ min-1, thereby accounting for 35-40 % of the estimated rate of heat production ( approximately 18 kJ min-1). 6. At exhaustion in DE, blood lactate values were low whereas blood glucose and muscle glycogen levels were still high. Exhaustion coincided with high body temperature ( approximately 40 C). 7. In conclusion, the present results demonstrate that reductions in exercising muscle blood flow with dehydration do not impair either the delivery of glucose and FFA or the removal of lactate during moderately intense prolonged exercise in the heat. However, dehydration during exercise in the heat elevates carbohydrate oxidation and lactate production. A major finding is that more than one-half of the metabolic heat liberated in the contracting leg muscles is dissipated directly to the surrounding environment. The present results indicate that hyperthermia, rather than altered metabolism, is the main factor underlying the early fatigue with dehydration during prolonged exercise in the heat.

Aspetti innovativi per la valutazione e la misura della porosità nei materiali dell'edilizia antica e moderna. La geometria frattale della porosità

New concepts on porosity appraisal in ancient and modern construction materials. The role of Fractal Geometry on porosity characterization and transport phenomena. This work studied the potential of Fractal Geometry to the characterization of porous materials. Besides the descriptive aspects of the pore size distribution, the fractal dimensions have led to the development of rational relations for the prediction of permeability coefficients to fluid and heat transfer. The research considered natural materials used in historical buildings (rock and earth) as well as currently employed materials as hydraulic cement and technologically advanced materials such as silicon carbide or YSZ ceramics. The experimental results of porosity derived from the techniques of mercury intrusion and from the image analysis. Data elaboration was carried out according to established procedures of Fractal Geometry. It was found that certain classes of materials are clearly fractal and respond to simple patterns such as Sierpinski and Menger models. In several cases, however, the fractal character is not recognised because the microstructure of the material is based on different phases at different dimensional scales, and in consequence the “fractal dimensions” calculated from porosimetric data do not come within the standard range (less than 3). Using different type and numbers of fractal units is possible, however, to obtain “virtual” microstructures that have the fraction of voids and pore size distribution equivalent with the experimental ones for almost any material. Thus it was possible to take the expressions for the permeability and the thermal conduction which does not require empirical “constants”, these expressions have also provided values that are generally in agreement with the experimental available data. More problematic has been the fractal discussion of the geometry of the rupture of the material subjected to mechanical stress both external and internal applied. The results achieved on these issues are qualitative and prone to future studies. Keywords: Materials, Microstructure, Porosity, Fractal Geometry, Permeability, Thermal conduction, Mechanical strength.

Sviluppo di metodi innovativi per la sintesi di nanoparticelle di interesse industriale

Among various nanoparticles, noble metal nanoparticles have attracted considerable attention due to their optical, catalytic and conducting properties. This work has been focused on the development of an innovative method of synthesis for the preparation of metal nanosuspensions of Au, Ag, Cu, in order to achieve stable sols, showing suitable features to allow an industrial scale up of the processes. The research was developed in collaboration with a company interested in the large scale production of the studied nanosuspensions. In order to develop a commercial process, high solid concentration, long time colloidal stability and particle size control, are required. Two synthesis routes, differing by the used solvents, have been implemented: polyol based and water based synthesis. In order to achieve a process intensification the microwave heating has been applied. As a result, colloidal nanosuspensions with suitable dimensions, good optical properties, very high solid content and good stability, have been synthesized by simple and environmental friendly methods. Particularly, due to some interesting results an optimized synthesis process has been patented. Both water and polyol based synthesis, developed in the presence of a reducing agent and of a chelating polymer, allowed to obtain particle size-control and colloidal stability by tuning the different parameters. Furthermore, it has been verified that microwave device, due to its rapid and homogeneous heating, provides some advantages over conventional method. In order to optimize the final suspensions properties, for each synthesis it has been studied the effect of different parameters (temperature, time, precursors concentrations, etc) and throughout a specific optimization action a right control on nucleation and growth processes has been achieved. The achieved nanoparticles were confirmed by XRD analysis to be the desired metal phases, even at the lowest synthesis temperatures. The particles showed a diameter, measured by STEM and dynamic light scattering technique (DLS), ranging from 10 to 60 nm. Surface plasmon resonance (SPR) was monitored by UV-VIS spectroscopy confirming its dependence by nanoparticles size and shape. Moreover the reaction yield has been assessed by ICP analysis performed on the unreacted metal cations. Finally, thermal conductivity and antibacterial activity characterizations of copper and silver sols respectively are now ongoing in order to check their application as nanofluid in heat transfer processes and as antibacterial agent.

Biomass Gasification - Process analysis and dimensioning aspects for downdraft units and gas cleaning lines

In such territories where food production is mostly scattered in several small / medium size or even domestic farms, a lot of heterogeneous residues are produced yearly, since farmers usually carry out different activities in their properties. The amount and composition of farm residues, therefore, widely change during year, according to the single production process periodically achieved. Coupling high efficiency micro-cogeneration energy units with easy handling biomass conversion equipments, suitable to treat different materials, would provide many important advantages to the farmers and to the community as well, so that the increase in feedstock flexibility of gasification units is nowadays seen as a further paramount step towards their wide spreading in rural areas and as a real necessity for their utilization at small scale. Two main research topics were thought to be of main concern at this purpose, and they were therefore discussed in this work: the investigation of fuels properties impact on gasification process development and the technical feasibility of small scale gasification units integration with cogeneration systems. According to these two main aspects, the present work was thus divided in two main parts. The first one is focused on the biomass gasification process, that was investigated in its theoretical aspects and then analytically modelled in order to simulate thermo-chemical conversion of different biomass fuels, such as wood (park waste wood and softwood), wheat straw, sewage sludge and refuse derived fuels. The main idea is to correlate the results of reactor design procedures with the physical properties of biomasses and the corresponding working conditions of gasifiers (temperature profile, above all), in order to point out the main differences which prevent the use of the same conversion unit for different materials. At this scope, a gasification kinetic free model was initially developed in Excel sheets, considering different values of air to biomass ratio and the downdraft gasification technology as particular examined application. The differences in syngas production and working conditions (process temperatures, above all) among the considered fuels were tried to be connected to some biomass properties, such elementary composition, ash and water contents. The novelty of this analytical approach was the use of kinetic constants ratio in order to determine oxygen distribution among the different oxidation reactions (regarding volatile matter only) while equilibrium of water gas shift reaction was considered in gasification zone, by which the energy and mass balances involved in the process algorithm were linked together, as well. Moreover, the main advantage of this analytical tool is the easiness by which the input data corresponding to the particular biomass materials can be inserted into the model, so that a rapid evaluation on their own thermo-chemical conversion properties is possible to be obtained, mainly based on their chemical composition A good conformity of the model results with the other literature and experimental data was detected for almost all the considered materials (except for refuse derived fuels, because of their unfitting chemical composition with the model assumptions). Successively, a dimensioning procedure for open core downdraft gasifiers was set up, by the analysis on the fundamental thermo-physical and thermo-chemical mechanisms which are supposed to regulate the main solid conversion steps involved in the gasification process. Gasification units were schematically subdivided in four reaction zones, respectively corresponding to biomass heating, solids drying, pyrolysis and char gasification processes, and the time required for the full development of each of these steps was correlated to the kinetics rates (for pyrolysis and char gasification processes only) and to the heat and mass transfer phenomena from gas to solid phase. On the basis of this analysis and according to the kinetic free model results and biomass physical properties (particles size, above all) it was achieved that for all the considered materials char gasification step is kinetically limited and therefore temperature is the main working parameter controlling this step. Solids drying is mainly regulated by heat transfer from bulk gas to the inner layers of particles and the corresponding time especially depends on particle size. Biomass heating is almost totally achieved by the radiative heat transfer from the hot walls of reactor to the bed of material. For pyrolysis, instead, working temperature, particles size and the same nature of biomass (through its own pyrolysis heat) have all comparable weights on the process development, so that the corresponding time can be differently depending on one of these factors according to the particular fuel is gasified and the particular conditions are established inside the gasifier. The same analysis also led to the estimation of reaction zone volumes for each biomass fuel, so as a comparison among the dimensions of the differently fed gasification units was finally accomplished. Each biomass material showed a different volumes distribution, so that any dimensioned gasification unit does not seem to be suitable for more than one biomass species. Nevertheless, since reactors diameters were found out quite similar for all the examined materials, it could be envisaged to design a single units for all of them by adopting the largest diameter and by combining together the maximum heights of each reaction zone, as they were calculated for the different biomasses. A total height of gasifier as around 2400mm would be obtained in this case. Besides, by arranging air injecting nozzles at different levels along the reactor, gasification zone could be properly set up according to the particular material is in turn gasified. Finally, since gasification and pyrolysis times were found to considerably change according to even short temperature variations, it could be also envisaged to regulate air feeding rate for each gasified material (which process temperatures depend on), so as the available reactor volumes would be suitable for the complete development of solid conversion in each case, without even changing fluid dynamics behaviour of the unit as well as air/biomass ratio in noticeable measure. The second part of this work dealt with the gas cleaning systems to be adopted downstream the gasifiers in order to run high efficiency CHP units (i.e. internal engines and micro-turbines). Especially in the case multi–fuel gasifiers are assumed to be used, weightier gas cleaning lines need to be envisaged in order to reach the standard gas quality degree required to fuel cogeneration units. Indeed, as the more heterogeneous feed to the gasification unit, several contaminant species can simultaneously be present in the exit gas stream and, as a consequence, suitable gas cleaning systems have to be designed. In this work, an overall study on gas cleaning lines assessment is carried out. Differently from the other research efforts carried out in the same field, the main scope is to define general arrangements for gas cleaning lines suitable to remove several contaminants from the gas stream, independently on the feedstock material and the energy plant size The gas contaminant species taken into account in this analysis were: particulate, tars, sulphur (in H2S form), alkali metals, nitrogen (in NH3 form) and acid gases (in HCl form). For each of these species, alternative cleaning devices were designed according to three different plant sizes, respectively corresponding with 8Nm3/h, 125Nm3/h and 350Nm3/h gas flows. Their performances were examined on the basis of their optimal working conditions (efficiency, temperature and pressure drops, above all) and their own consumption of energy and materials. Successively, the designed units were combined together in different overall gas cleaning line arrangements, paths, by following some technical constraints which were mainly determined from the same performance analysis on the cleaning units and from the presumable synergic effects by contaminants on the right working of some of them (filters clogging, catalysts deactivation, etc.). One of the main issues to be stated in paths design accomplishment was the tars removal from the gas stream, preventing filters plugging and/or line pipes clogging At this scope, a catalytic tars cracking unit was envisaged as the only solution to be adopted, and, therefore, a catalytic material which is able to work at relatively low temperatures was chosen. Nevertheless, a rapid drop in tars cracking efficiency was also estimated for this same material, so that an high frequency of catalysts regeneration and a consequent relevant air consumption for this operation were calculated in all of the cases. Other difficulties had to be overcome in the abatement of alkali metals, which condense at temperatures lower than tars, but they also need to be removed in the first sections of gas cleaning line in order to avoid corrosion of materials. In this case a dry scrubber technology was envisaged, by using the same fine particles filter units and by choosing for them corrosion resistant materials, like ceramic ones. Besides these two solutions which seem to be unavoidable in gas cleaning line design, high temperature gas cleaning lines were not possible to be achieved for the two larger plant sizes, as well. Indeed, as the use of temperature control devices was precluded in the adopted design procedure, ammonia partial oxidation units (as the only considered methods for the abatement of ammonia at high temperature) were not suitable for the large scale units, because of the high increase of reactors temperature by the exothermic reactions involved in the process. In spite of these limitations, yet, overall arrangements for each considered plant size were finally designed, so that the possibility to clean the gas up to the required standard degree was technically demonstrated, even in the case several contaminants are simultaneously present in the gas stream. Moreover, all the possible paths defined for the different plant sizes were compared each others on the basis of some defined operational parameters, among which total pressure drops, total energy losses, number of units and secondary materials consumption. On the basis of this analysis, dry gas cleaning methods proved preferable to the ones including water scrubber technology in al of the cases, especially because of the high water consumption provided by water scrubber units in ammonia adsorption process. This result is yet connected to the possibility to use activated carbon units for ammonia removal and Nahcolite adsorber for chloride acid. The very high efficiency of this latter material is also remarkable. Finally, as an estimation of the overall energy loss pertaining the gas cleaning process, the total enthalpy losses estimated for the three plant sizes were compared with the respective gas streams energy contents, these latter obtained on the basis of low heating value of gas only. This overall study on gas cleaning systems is thus proposed as an analytical tool by which different gas cleaning line configurations can be evaluated, according to the particular practical application they are adopted for and the size of cogeneration unit they are connected to.

Fluidodinamica biomedica computazionale del flusso sanguigno in presenza di affezioni strumentali e/o patologiche

La tesi di Dottorato studia il flusso sanguigno tramite un codice agli elementi finiti (COMSOL Multiphysics). Nell’arteria è presente un catetere Doppler (in posizione concentrica o decentrata rispetto all’asse di simmetria) o di stenosi di varia forma ed estensione. Le arterie sono solidi cilindrici rigidi, elastici o iperelastici. Le arterie hanno diametri di 6 mm, 5 mm, 4 mm e 2 mm. Il flusso ematico è in regime laminare stazionario e transitorio, ed il sangue è un fluido non-Newtoniano di Casson, modificato secondo la formulazione di Gonzales & Moraga. Le analisi numeriche sono realizzate in domini tridimensionali e bidimensionali, in quest’ultimo caso analizzando l’interazione fluido-strutturale. Nei casi tridimensionali, le arterie (simulazioni fluidodinamiche) sono infinitamente rigide: ricavato il campo di pressione si procede quindi all’analisi strutturale, per determinare le variazioni di sezione e la permanenza del disturbo sul flusso. La portata sanguigna è determinata nei casi tridimensionali con catetere individuando tre valori (massimo, minimo e medio); mentre per i casi 2D e tridimensionali con arterie stenotiche la legge di pressione riproduce l’impulso ematico. La mesh è triangolare (2D) o tetraedrica (3D), infittita alla parete ed a valle dell’ostacolo, per catturare le ricircolazioni. Alla tesi sono allegate due appendici, che studiano con codici CFD la trasmissione del calore in microcanali e l’ evaporazione di gocce d’acqua in sistemi non confinati. La fluidodinamica nei microcanali è analoga all’emodinamica nei capillari. Il metodo Euleriano-Lagrangiano (simulazioni dell’evaporazione) schematizza la natura mista del sangue. La parte inerente ai microcanali analizza il transitorio a seguito dell’applicazione di un flusso termico variabile nel tempo, variando velocità in ingresso e dimensioni del microcanale. L’indagine sull’evaporazione di gocce è un’analisi parametrica in 3D, che esamina il peso del singolo parametro (temperatura esterna, diametro iniziale, umidità relativa, velocità iniziale, coefficiente di diffusione) per individuare quello che influenza maggiormente il fenomeno.

Untersuchungen zur selektiven Deletion alloreaktiver Spender-T- Lymphozyten durch CD178-modifizierte dendritische Zellen im Rahmen der allogenen Blutstammzelltransplantation

Eine der häufigsten Komplikationen bei der allogenen Blutstammzelltransplantation stellt die Transplantat-gegen-Wirt-Erkrankung (Graft versus Host Disease, GvHD) dar. Sie wird durch allogene Spender-T-Lymphozyten verursacht, die Gewebe des Transplantatempfängers erkennen und inflammatorische Entzündungsprozesse auslösen. Neben dieser Alloreaktivität induzieren Spender-T-Lymphozyten jedoch auch immuntherapeutisch erwünschte Transplantat-gegen-Leukämie-Reaktionen (Graft versus Leukemia, GvL-Reaktion), bei denen residuelle Tumor- bzw. Leukämiezellen im Patienten durch Spender-T-Zellen spezifisch erkannt und eliminiert werden. Im Rahmen einer verbesserten Immmuntherapie wird daher versucht, GvHD-reaktive und GvL-reaktive Spender-T-Lymphozyten effizient voneinander zu separieren und so eine wirkungsvolle GvHD-Prophylaxe bzw. optimierte GvL-Induktion zu erreichen. In diesem Kontext war es Ziel dieser Arbeit, murine dendritische Zellen (DZ) so zu modifizieren, daß sie für die spezifische Deletion alloreaktiver T-Zellen in murinen GvHD/GvL-Tiermodellen eingesetzt werden können. Die Modifikation der DZ sollte dazu führen, daß über das CD95/CD178-System Aktivierungs-induzierter Zelltod (activation induced cell death, AICD) in alloreaktiven T-Zellen ausgelöst wird. Hierzu wurden für die Modifikation der DZ zwei verschiedene Mechanismen angewandt: a) die Transfektion der DZ mit CD178-mRNA sowie b) die zielgerichtete Immobilisierung von hCD178-X-Fusionsproteinen auf Oberflächenmolekülen von DZ bzw. T-Zellen. Als Positivkontrolle für die Induktion CD95-vermittelter Apoptose diente der agonistische anti-CD95-Antikörper Jo2. Bei der Transfektion muriner DZ mit mRNA zeigte sich anhand des Reportergens EGFP, daß aus dem Knochenmark generierte DZ mit hoher Effizienz mit EGFP-mRNA transfizierbar waren. Im Falle von hCD178-mRNA führte die Transfektion jedoch zu einer insuffizienten CD178-Expression, die mit den regulatorischen Eigenschaften der zytoplasmatischen CD178-Region in Verbindung gebracht werden konnte. So führte die Verwendung einer zytoplasmatisch trunkierten Form der CD178-mRNA (CD178Dzyt) zu einer durchflußzytometrisch nachweisbaren CD178-Expression in DZ. Mit diesen CD178Dzyt-exprimierenden DZ konnte in einem Proliferationstest die Proliferation alloreaktiver T-Zellen inhibiert werden. Die Beladung von DZ bzw. von T-Zellen mit hCD178-X-Fusionsproteinen führte in vitro ebenfalls zu einer deutlichen Reduktion von Alloreaktivität. Dabei konnte eine spezifische Deletion/Inhibition alloreaktiver T-Zellen nachgewiesen werden. Die Elimination alloreaktiver T-Zellen erfolgte in beiden Verfahren über AICD. Darüber hinaus wurde eine Bifunktionalität der Fusionsproteine festgestellt, da sie neben der Induktion CD95-vermittelter Apoptose auch in der Lage waren, die Kostimulation allogener T-Zellen effizient zu inhibieren. Mit Hilfe adoptiver T-Zell-Transferexperimente konnten abschließend die in vitro gewonnenen Ergebnisse in vivo in zwei verschiedenen GvHD-Mausmodellen bestätigt werden.

CFD modeling of two-phase boiling flows in the slug flow regime with an interface capturing technique

The objective of this thesis was to improve the commercial CFD software Ansys Fluent to obtain a tool able to perform accurate simulations of flow boiling in the slug flow regime. The achievement of a reliable numerical framework allows a better understanding of the bubble and flow dynamics induced by the evaporation and makes possible the prediction of the wall heat transfer trends. In order to save computational time, the flow is modeled with an axisymmetrical formulation. Vapor and liquid phases are treated as incompressible and in laminar flow. By means of a single fluid approach, the flow equations are written as for a single phase flow, but discontinuities at the interface and interfacial effects need to be accounted for and discretized properly. Ansys Fluent provides a Volume Of Fluid technique to advect the interface and to map the discontinuous fluid properties throughout the flow domain. The interfacial effects are dominant in the boiling slug flow and the accuracy of their estimation is fundamental for the reliability of the solver. Self-implemented functions, developed ad-hoc, are introduced within the numerical code to compute the surface tension force and the rates of mass and energy exchange at the interface related to the evaporation. Several validation benchmarks assess the better performances of the improved software. Various adiabatic configurations are simulated in order to test the capability of the numerical framework in modeling actual flows and the comparison with experimental results is very positive. The simulation of a single evaporating bubble underlines the dominant effect on the global heat transfer rate of the local transient heat convection in the liquid after the bubble transit. The simulation of multiple evaporating bubbles flowing in sequence shows that their mutual influence can strongly enhance the heat transfer coefficient, up to twice the single phase flow value.

Identifizierung und Charakterisierung von Interaktionspartnern des synaptischen Vesikelproteins Synaptophysin

Die neuronale Signalübertragung beruht auf dem synaptischen Vesikelzyklus, der durch das koordinierte Zusammenspiel von circa 400 verschiedenen Proteinen reguliert wird. Eines der Hauptproteine des synaptischen Vesikels ist Synaptophysin (SYP), das zu den tetraspan vesicle membrane proteins (TVPs) gehört. Es wird vermutet, dass es zahlreiche Funktionen der Exo- und Endozytose moduliert, wenngleich die zugrunde liegenden molekularen Mechanismen bisher größtenteils unverstanden sind. Ziel der Arbeit war daher die Identifizierung von Interaktionspartnern von SYP, um zum Verständnis der vielen ungeklärten Prozesse im synaptischen Vesikelzyklus beizutragen. Mit dem Split-Ubiquitin Yeast Two-Hybrid System, das eine direkte in vivo Interaktion von Membranproteinen erlaubt, konnten in der vorliegenden Arbeit bekannte, aber auch neue SYP-Bindungspartner identifiziert werden. Ein bekannter Interaktionspartner war Synaptobrevin2 (SYB2), das zu den stärksten im Split-Ubiquitin Y2H System identifizierten Bindeproteinen zählt. Zu den neuen starken SYP-Interaktionspartnern gehören die TVPs Synaptogyrin3 (SYNGR3) und SCAMP1. Somit konnten erstmals heterophile Interaktionen zwischen den verschiedenen TVP-Genfamilien nachgewiesen werden, die für eine universelle Funktion der TVPs sprechen. Die Validierung der im Split-Ubiquitin Y2H System ermittelten Interaktionspartner wurde auf eine Auswahl von Proteinen beschränkt, die vermutlich am synaptischen Vesikelzyklus beteiligt sind. Dabei konnte eine immunhistologische Kolokalisierung von SYP mit SYB2, SYNGR3, SCAMP1, Stathmin-like3 (STMN3), Rho family GTPase2 (RND2), Phospholipid transfer protein, Vesicle transport through interaction with t-SNAREs 1B homolog, Arfaptin2 und Profilin1 in den Synapsen-reichen Schichten der Retina beobachtet werden. Die SYP/SYB2- und SYP/SYNGR3-Komplexe konnten zudem sowohl aus Synaptosomen-Lysat als auch aus cDNA-transfizierten Epithelzellen koimmunpräzipitiert werden, wohingegen dies für die anderen Interaktionspartner nicht gelang. Da Koimmunpräzipitation die Struktur der Proteine durch Solubilisierung mit Detergenzien beeinflusst, wurden die in der Hefe beobachteten Interaktionen noch mittels Fluoreszenz-Resonanz-Energie-Transfer überprüft, mit dem Proteinwechselwirkungen in der nativen Umgebung nachgewiesen werden können. Ein positives FRET-Signal konnte für SYP mit SYB2, SYP, SYNGR3, SCAMP1, STMN3, RND2 und Arfaptin2 detektiert werden, lediglich für SYP mit Phospholipase D4 (PLD4) gelang dieser Nachweis nicht. Ferner zeigten FRET-Analysen von Synaptophysin-Mutanten, dass der zytoplasmatische C-Terminus für die Interaktion mit zytoplasmatischen und membranassoziierten Proteinen benötigt wird. Durch in vivo FRET-Studien mit der SH2-Domäne der Src-Kinase, die an phosphorylierte Tyrosine bindet, konnte eine Tyrosin-Phosphorylierung des zytoplasmatischen C-Terminus von Synaptophysin und von Synaptogyrin3 detektiert werden. Viele der neu identifizierten Synaptophysin-Interaktionspartner sind im Lipid-Metabolismus involviert. Vermutlich rekrutiert der zytoplasmatische und durch Phosphorylierung modifizierbare C-Terminus diese Partner in spezifische Lipoproteindomänen, die an der Feinabstimmung der synaptischen Vesikelendo- und -exozytose beteiligt sind.

Induktion regulatorischer T-Zellen zur Inhibition allergenspezifischer Immunantworten im Mausmodell der Typ I-Allergie

Die Induktion regulatorischer T-Zellen (Treg) spielt im Zusammenhang mit der Kontrolle allergenspezifischer Reaktionen, insbesondere auch im Rahmen einer erfolgreichen Hyposensibilisierung mit hohen Allergendosen, eine zentrale Rolle. In der vorliegenden Arbeit wurden die Mechanismen der Rekrutierung allergenspezifischer Treg daher in einem Mausmodell untersucht, in dem analog zur spezifischen Immuntherapie (SIT) die repetitive Verabreichung von hohen Antigendosen einen IgE-spezifischen Suppressionsmechanismus aktiviert, während die Injektion niedriger Antigendosen eine potente IgE-Antwort induziert. Th1-Zellen sowie konventionelle CD4+CD25+ oder CD8+CD28- Treg konnten als Vermittlerpopulationen des suppressiven Effektes in hochdosig immunisierten Mäusen ausgeschlossen werden. Mittels Transferexperimenten wurden erstmals CD4-CD8- doppelt negative Treg als eine die IgE-Suppression vermittelnde Zellpopulation identifiziert. Desweiteren wurden DNA-Transferexperimente durchgeführt, mit dem Ziel, adaptive Treg zum Zwecke der Inhibition allergenspezifischer Immunreaktionen zu induzieren. Dazu wurden IL-10- bzw. TGF-ß-kodierende Plasmide (pCMV-IL-10, pCMV-TGF-ß) hergestellt und in Kombination mit einem Plasmid, welches das Modellallergen ß-Galaktosidase (ßGal) unter der Kontrolle des DC-spezifischen Fascin-Promotors (pFascin-ßGal) kodierte, Mäusen mit der Genpistole appliziert. Die Expression des Modellallergens in Verbindung mit der konstitutiven Produktion von immunsuppressiven Zytokinen sollte bei den mit den transfizierten DC interagierenden antigenspezifischen T-Zellen zu einer verstärkten Differenzierung von Treg führen. Die Experimente zeigten, dass die Koapplikation von IL-10-kodierenden Plasmiden eine Immunsuppression induziert, die sich in einer verminderten antigenspezifischen Antikörperproduktion, Zytokinproduktion und CTL-Induktion zeigt, die jedoch bei nachfolgender Sensibilisierung mit ßGal-Protein nicht aufrechterhalten werden kann. Dahingegen führte die Koapplikation von TGF-ß-kodierenden Plasmiden verbunden mit einer nachfolgenden Sensibilisierung zu einer leichten Inhibition der IgG1- und IgG2a-Produktion verglichen mit der Vakzinierung mit pFascin-ßGal allein. Dieser inhibitorische Effekt von pCMV-TGF-ß wurde interessanterweise nicht bereits nach der DNA-Immunisierung, sondern erst nach Sensibilisierung mit dem Protein beobachtet.

Analisi sperimentale e modellazione della conducibilità termica in materiali per la protezione passiva da incendio esterno

Numerosi incidenti verificatisi negli ultimi dieci anni in campo chimico e petrolchimico sono dovuti all’innesco di sostanze infiammabili rilasciate accidentalmente: per questo motivo gli scenari incidentali legati ad incendi esterni rivestono oggigiorno un interesse crescente, in particolar modo nell’industria di processo, in quanto possono essere causa di ingenti danni sia ai lavoratori ed alla popolazione, sia alle strutture. Gli incendi, come mostrato da alcuni studi, sono uno dei più frequenti scenari incidentali nell’industria di processo, secondi solo alla perdita di contenimento di sostanze pericolose. Questi eventi primari possono, a loro volta, determinare eventi secondari, con conseguenze catastrofiche dovute alla propagazione delle fiamme ad apparecchiature e tubazioni non direttamente coinvolte nell’incidente primario; tale fenomeno prende il nome di effetto domino. La necessità di ridurre le probabilità di effetto domino rende la mitigazione delle conseguenze un aspetto fondamentale nella progettazione dell’impianto. A questo scopo si impiegano i materiali per la protezione passiva da fuoco (Passive Fire Protection o PFP); essi sono sistemi isolanti impiegati per proteggere efficacemente apparecchiature e tubazioni industriali da scenari di incendio esterno. L’applicazione dei materiali per PFP limita l’incremento di temperatura degli elementi protetti; questo scopo viene raggiunto tramite l’impiego di differenti tipologie di prodotti e materiali. Tuttavia l’applicazione dei suddetti materiali fireproofing non può prescindere da una caratterizzazione delle proprietà termiche, in particolar modo della conducibilità termica, in condizioni che simulino l’esposizione a fuoco. Nel presente elaborato di tesi si è scelto di analizzare tre materiali coibenti, tutti appartenenti, pur con diversità di composizione e struttura, alla classe dei materiali inorganici fibrosi: Fibercon Silica Needled Blanket 1200, Pyrogel®XT, Rockwool Marine Firebatt 100. I tre materiali sono costituiti da una fase solida inorganica, differente per ciascuno di essi e da una fase gassosa, preponderante come frazione volumetrica. I materiali inorganici fibrosi rivestono una notevole importanza rispetto ad altri materiali fireproofing in quanto possono resistere a temperature estremamente elevate, talvolta superiori a 1000 °C, senza particolari modifiche chimico-fisiche. Questo vantaggio, unito alla versatilità ed alla semplicità di applicazione, li rende leader a livello europeo nei materiali isolanti, con una fetta di mercato pari circa al 60%. Nonostante l’impiego dei suddetti materiali sia ormai una realtà consolidata nell’industria di processo, allo stato attuale sono disponibili pochi studi relativi alle loro proprietà termiche, in particolare in condizioni di fuoco. L’analisi sperimentale svolta ha consentito di identificare e modellare il comportamento termico di tali materiali in caso di esposizione a fuoco, impiegando nei test, a pressione atmosferica, un campo di temperatura compreso tra 20°C e 700°C, di interesse per applicazioni fireproofing. Per lo studio delle caratteristiche e la valutazione delle proprietà termiche dei tre materiali è stata impiegata principalmente la tecnica Transient Plane Source (TPS), che ha consentito la determinazione non solo della conducibilità termica, ma anche della diffusività termica e della capacità termica volumetrica, seppure con un grado di accuratezza inferiore. I test sono stati svolti su scala di laboratorio, creando un set-up sperimentale che integrasse opportunamente lo strumento Hot Disk Thermal Constants Analyzer TPS 1500 con una fornace a camera ed un sistema di acquisizione dati. Sono state realizzate alcune prove preliminari a temperatura ambiente sui tre materiali in esame, per individuare i parametri operativi (dimensione sensori, tempi di acquisizione, etc.) maggiormente idonei alla misura della conducibilità termica. Le informazioni acquisite sono state utilizzate per lo sviluppo di adeguati protocolli sperimentali e per effettuare prove ad alta temperatura. Ulteriori significative informazioni circa la morfologia, la porosità e la densità dei tre materiali sono state ottenute attraverso stereo-microscopia e picnometria a liquido. La porosità, o grado di vuoto, assume nei tre materiali un ruolo fondamentale, in quanto presenta valori compresi tra 85% e 95%, mentre la frazione solida ne costituisce la restante parte. Inoltre i risultati sperimentali hanno consentito di valutare, con prove a temperatura ambiente, l’isotropia rispetto alla trasmissione del calore per la classe di materiali coibenti analizzati, l’effetto della temperatura e della variazione del grado di vuoto (nel caso di materiali che durante l’applicazione possano essere soggetti a fenomeni di “schiacciamento”, ovvero riduzione del grado di vuoto) sulla conducibilità termica effettiva dei tre materiali analizzati. Analoghi risultati, seppure con grado di accuratezza lievemente inferiore, sono stati ottenuti per la diffusività termica e la capacità termica volumetrica. Poiché è nota la densità apparente di ciascun materiale si è scelto di calcolarne anche il calore specifico in funzione della temperatura, di cui si è proposto una correlazione empirica. I risultati sperimentali, concordi per i tre materiali in esame, hanno mostrato un incremento della conducibilità termica con la temperatura, da valori largamente inferiori a 0,1 W/(m∙K) a temperatura ambiente, fino a 0,3÷0,4 W/(m∙K) a 700°C. La sostanziale similitudine delle proprietà termiche tra i tre materiali, appartenenti alla medesima categoria di materiali isolanti, è stata riscontrata anche per la diffusività termica, la capacità termica volumetrica ed il calore specifico. Queste considerazioni hanno giustificato l’applicazione a tutti i tre materiali in esame dei medesimi modelli per descrivere la conducibilità termica effettiva, ritenuta, tra le proprietà fisiche determinate sperimentalmente, la più significativa nel caso di esposizione a fuoco. Lo sviluppo di un modello per la conducibilità termica effettiva si è reso necessario in quanto i risultati sperimentali ottenuti tramite la tecnica Transient Plane Source non forniscono alcuna informazione sui contributi offerti da ciascun meccanismo di scambio termico al termine complessivo e, pertanto, non consentono una facile generalizzazione della proprietà in funzione delle condizioni di impiego del materiale. La conducibilità termica dei materiali coibenti fibrosi e in generale dei materiali bi-fasici tiene infatti conto in un unico valore di vari contributi dipendenti dai diversi meccanismi di scambio termico presenti: conduzione nella fase gassosa e nel solido, irraggiamento nelle superfici delle cavità del solido e, talvolta, convezione; inoltre essa dipende fortemente dalla temperatura e dalla porosità. Pertanto, a partire dal confronto con i risultati sperimentali, tra cui densità e grado di vuoto, l’obiettivo centrale della seconda fase del progetto è stata la scelta, tra i numerosi modelli a disposizione in letteratura per materiali bi-fasici, di cui si è presentata una rassegna, dei più adatti a descrivere la conducibilità termica effettiva nei materiali in esame e nell’intervallo di temperatura di interesse, fornendo al contempo un significato fisico ai contributi apportati al termine complessivo. Inizialmente la scelta è ricaduta su cinque modelli, chiamati comunemente “modelli strutturali di base” (Serie, Parallelo, Maxwell-Eucken 1, Maxwell-Eucken 2, Effective Medium Theory) [1] per la loro semplicità e versatilità di applicazione. Tali modelli, puramente teorici, hanno mostrato al raffronto con i risultati sperimentali numerosi limiti, in particolar modo nella previsione del termine di irraggiamento, ovvero per temperature superiori a 400°C. Pertanto si è deciso di adottare un approccio semi-empirico: è stato applicato il modello di Krischer [2], ovvero una media pesata su un parametro empirico (f, da determinare) dei modelli Serie e Parallelo, precedentemente applicati. Anch’esso si è rivelato non idoneo alla descrizione dei materiali isolanti fibrosi in esame, per ragioni analoghe. Cercando di impiegare modelli caratterizzati da forte fondamento fisico e grado di complessità limitato, la scelta è caduta sui due recenti modelli, proposti rispettivamente da Karamanos, Papadopoulos, Anastasellos [3] e Daryabeigi, Cunnington, Knutson [4] [5]. Entrambi presentavano il vantaggio di essere stati utilizzati con successo per materiali isolanti fibrosi. Inizialmente i due modelli sono stati applicati con i valori dei parametri e le correlazioni proposte dagli Autori. Visti gli incoraggianti risultati, a questo primo approccio è seguita l’ottimizzazione dei parametri e l’applicazione di correlazioni maggiormente idonee ai materiali in esame, che ha mostrato l’efficacia dei modelli proposti da Karamanos, Papadopoulos, Anastasellos e Daryabeigi, Cunnington, Knutson per i tre materiali analizzati. Pertanto l’obiettivo finale del lavoro è stato raggiunto con successo in quanto sono stati applicati modelli di conducibilità termica con forte fondamento fisico e grado di complessità limitato che, con buon accordo ai risultati sperimentali ottenuti, consentono di ricavare equazioni predittive per la stima del comportamento, durante l’esposizione a fuoco, dei materiali fireproofing in esame. Bologna, Luglio 2013 Riferimenti bibliografici: [1] Wang J., Carson J.K., North M.F., Cleland D.J., A new approach to modelling the effective thermal conductivity of heterogeneous materials. International Journal of Heat and Mass Transfer 49 (2006) 3075-3083. [2] Krischer O., Die wissenschaftlichen Grundlagen der Trocknungstechnik (The Scientific Fundamentals of Drying Technology), Springer-Verlag, Berlino, 1963. [3] Karamanos A., Papadopoulos A., Anastasellos D., Heat Transfer phenomena in fibrous insulating materials. (2004) Geolan.gr http://www.geolan.gr/sappek/docs/publications/article_6.pdf Ultimo accesso: 1 Luglio 2013. [4] Daryabeigi K., Cunnington G. R., and Knutson J. R., Combined Heat Transfer in High-Porosity High-Temperature Fibrous Insulation: Theory and Experimental Validation. Journal of Thermophysics and Heat Transfer 25 (2011) 536-546. [5] Daryabeigi K., Cunnington G.R., Knutson J.R., Heat Transfer Modeling for Rigid High-Temperature Fibrous Insulation. Journal of Thermophysics and Heat Transfer. AIAA Early Edition/1 (2012).

Die Rolle CD4 + CD25 + regulatorischer T-Zellen in der Niedrigzonentoleranz gegenüber Kontaktallergenen

Die allergische Kontaktdermatitis ist eine der häufigsten Berufserkrankungen, die durch die Exposition mit hohen Mengen eines Kontaktallergens ausgelöst wird. In Mausmodellen sehen wir, dass mittels einer Niedrigzonentoleranz (NZT) die Bildung einer Kontaktsensibilisierung unterdrückt werden kann. Bei der NZT führt die epikutane Applikation von subimmunogenen Dosen zu einer systemischen Toleranzentwicklung, die durch CD8+ Suppressor-T-Zellen Hapten-spezifisch vermittelt wird. Für die Generierung dieser CD8+ Suppressor-T-Zellen sind IL-10-sezernierende CD4+ regulatorischen T-Zellen (Tregs) notwendig. Aufbauend auf diesen Ergebnissen sollte in dieser Arbeit überprüft werden, ob natürlichen Tregs (nTregs) bei der NZT eine Rolle spielen und die Funktion und Aufgaben dieser Zellen während der NZT untersucht werden. rnWir konnten keine erhöhte Anzahl von nTregs während der Niedrigzonentoleranz gegenüber Kontaktallergenen im Vergleich zur CHS charakterisieren. Weiterhin haben wir gezeigt, dass eine Reduktion der nTregs durch Depletion mittels anti-CD25-Anikörper oder durch Cyclophosphamid-Gabe die Entstehung der CD8+ Suppressor-T-Zellen der NZT unterdrückt und damit die Entwicklung der Toleranzreaktion verhindert wird. Ferner wurde beobachtet, dass eine epikutane NZT Hapten-spezifisch durch CD8+ T-Zellen übertragen werden kann, während CD4+CD25+ T-Zellen eine Hapten-unspezifische Wirkung zeigten.rn

Die Rolle der IFN-gamma Signalübertragung und von MyD88 in der Angiotensin-II-induzierten vaskulären Dysfunkion, Inflammation und arteriellen Hypertonie

Im Rahmen dieser Arbeit wurde die Rolle von myelomonozytären Zellen, IFN-gamma (Interferon gamma), MyD88 (myeloid differentiation factor 88) und zugrundeliegenden Signalwege in der Angiotensin II (ATII)-induzierten vaskulären Inflammation, Dysfunktion und arteriellen Hypertonie untersucht. Wie bereits veröffentlichte Vordaten aus meiner Arbeitsgruppe zeigten, schützt die Depletion von Lysozym M (LysM)+ myelomonozytären Zellen (Diphteriatoxin-vermittelt in Mäusen, die transgen für den humanen Diphtheriatoxin-Rezeptor sind, LysMiDTR Mäuse) vor der ATII-induzierten vaskulären Dysfunktion und arterieller Hypertonie, und kann durch adoptiven Zelltransfer von Wildtyp Monozyten wiederhergestellt werden. In meiner Arbeit konnte ich zeigen, dass die Rekonstitution von Monozyten-depletierten LysMiDTR Mäusen mit Wildtyp Monozyten den Phänotyp der vaskulären Dysfunktion wiederherstellen kann, die Rekonstitution mit gp91phox-/y oder Agtr1-/- Monozyten jedoch nicht. Die Hypertonus-mediierenden Effekte dieser infiltrierenden Monozyten scheinen demnach von der intakten ATII und NADPH Oxidase Signalübertragung in diesen Zellen abhängig zu sein. Vermutlich ebenfalls für die Aktivierung der Monozyten funktionell wichtig sind IFN-gamma, produziert durch NK-Zellen, und der Transkriptionsfaktor T-bet (T-box expressed in T cells), exprimiert von NK-Zellen und Monozyten. IFN-gamma-/- Mäuse waren partiell geschützt vor der ATII-induzierten vaskulären Dysfunktion und charakterisiert durch reduzierte Level an Superoxid im Gefäß im Vergleich zu ATII-infundierten Wildtyp Mäusen. IFN-gamma-/- und T-bet defiziente Tbx21-/- Mäuse zeichneten sich ferner durch eine reduzierte ATII-mediierte Rekrutierung von NK1.1+ NK-Zellen, als ein Hautproduzent von IFN-gamma, sowie CD11b+GR-1low Interleukin-12 (IL-12) kompetenten Monozyten aus. Durch Depletions- und adoptive Transferexperimente konnte ich in dieser Arbeit NK-Zellen als essentielle Mitstreiter in der vaskulären Dysfunktion identifizieren und stellte fest, dass T-bet+LysM+ myelomonozytäre Zellen für die NK-Zellrekrutierung in die Gefäßwand und lokale IFN-gamma Produktion benötigt werden. Damit wurde erstmals NK-Zellen eine essentielle Rolle in der ATII-induzierten vaskulären Dysfunktion zugeschrieben. Außerdem wurde der T-bet-IFN-gamma Signalweg und die gegenseitige Monozyten-NK-Zellaktivierung als ein potentielles therapeutisches Ziel in kardiovaskulären Erkrankungen aufgedeckt. Des Weiteren identifizierte ich in meiner Arbeit MyD88 als ein zentrales Signalmolekül in der ATII-getriebenen Inflammation und vaskulären Gefäßschädigung. MyD88 Defizienz reduzierte den ATII-induzierten Anstieg des systolischen Blutdrucks und die endotheliale und glattmuskuläre vaskuläre Dysfunktion. Zusätzlich waren die vaskuläre Superoxid-Bildung sowie die Expressionslevel der NADPH Oxidase, der wichtigsten Quelle für oxidativem Stress im Gefäß, in ATII-infundierten MyD88-/- Mäusen im Vergleich zum Wildtyp reduziert. Mit Hilfe von durchflusszytometrischen Analysen deckte ich zudem auf, dass die ATII-induzierte Einwanderung von CD45+ Leukozyten, insbesondere CD11b+Ly6G-Ly6Chigh inflammatorischen Monozyten in MyD88-/- Mäusen signifikant abgeschwächt war. Diese Resultate wurden durch immunhistochemische Untersuchung von Aortengewebe auf CD68+, F4/80+ und Nox2+ Makrophagen/Phagozyten sowie Expressionsanalysen von Inflammationsmarkern untermauert. Analysen der mRNA Expression in Aortengewebe zeigten ferner eine in Wildtyp Mäusen nach ATII Infusion tendenziell gesteigerte Expression von inflammatorischen Monozytenmakern sowie eine abnehmende Expression von reparativen Monozytenmarken, während dieser Shift zu einem proinflammatorsichen Phänotyp in MyD88-/- blockiert zu sein schien. Dies zeigt eine Rolle von MyD88 in der terminalen Differenzierung von myelomonozytären Zellen an. Um dies weitergehend zu untersuchen und aufzudecken, ob die MyD88 Effekte abhängig sind von Zellen der hämatopoetischen Linie oder Gewebszellen, wurden Knochenmarktransferexperimente durchgeführt. MyD88 Defizienz in Knochenmark-abstammende Zellen reduzierte die ATII-induzierte vaskuläre Dysfunktion und Infiltration der Gefäßwand mit CD45+ Leukozyten und inflammatorischen myelomonozytären Zellen. Die protektiven Effekte der MyD88 Defizienz in der Angiotensin II-induzierten Inflammation konnten nicht auf Signalwege über die Toll-like Rezeptoren TLR2, -7 oder -9 zurückgeführt werden, wie die Untersuchung der vaskulären Reaktivität entsprechender Knockout Mäuse zeigte. Zusammenfassend konnte ich in meiner Arbeit zeigen, dass die Infiltration der Gefäßwand mit Nox2+AT1R+T-bet+MyD88+ myelomonozytären Zellen und die Wechselwirkung und gegenseitige Aktivierung dieser Zellen mit IFN-gamma produzierenden NK-Zellen eine zentrale Bedeutung in der Pathogenese der Angiotensin II (ATII)-induzierten vaskulären Dysfunktion, Inflammation und arteriellen Hypertonie einnehmen.

Global lymphoid tissue remodeling during a viral infection is orchestrated by a B cell-lymphotoxin-dependent pathway

Adaptive immune responses are characterized by substantial restructuring of secondary lymphoid organs. The molecular and cellular factors responsible for virus-induced lymphoid remodeling are not well known to date. Here we applied optical projection tomography, a mesoscopic imaging technique, for a global analysis of the entire 3-dimensional structure of mouse peripheral lymph nodes (PLNs), focusing on B-cell areas and high endothelial venule (HEV) networks. Structural homeostasis of PLNs was characterized by a strict correlation between total PLN volume, B-cell volume, B-cell follicle number, and HEV length. After infection with lymphocytic choriomeningitis virus, we observed a substantial, lymphotoxin (LT) beta-receptor-dependent reorganization of the PLN microarchitecture, in which an initial B-cell influx was followed by 3-fold increases in PLN volume and HEV network length on day 8 after infection. Adoptive transfer experiments revealed that virus-induced PLN and HEV network remodeling required LTalpha(1)beta(2)-expressing B cells, whereas the inhibition of vascular endothelial growth factor-A signaling pathways had no significant effect on PLN expansion. In summary, lymphocytic choriomeningitis virus-induced PLN growth depends on a vascular endothelial growth factor-A-independent, LT- and B cell-dependent morphogenic pathway, as revealed by an in-depth mesoscopic analysis of the global PLN structure.