Effects of electroplated zinc-nickel alloy coatings on the fatigue strength of AISI 4340 high-strength steel

Recovered substrates have been extensively used in the aerospace field. Cadmium electroplating has been widely applied to promote protective coatings in aeronautical components, resulting in excellent corrosion protection combined with a good performance in cyclic loading. Ecological considerations allied to the increasing demands for corrosion resistance have resulted in the search for possible alternatives. Zinc-nickel (Zn-Ni) alloys have received considerable interest recently, because these coatings show advantages such as a good resistance to white and red rust, high plating rates, and acceptance in the market. In this study, the effect of electroplated Zn-Ni coatings on AISI 4340 high-strength steel was analyzed for rotating bending fatigue strength, corrosion, and adhesion resistance. The compressive residual stress field was measured by x-ray diffraction prior to fatigue tests. Optical microscopy documented coating thickness, adhesion characteristics, and coverage extent for nearly all substrates. Fractured fatigue specimens were investigated using scanning electron microscopy (SEM). Three different Zn-Ni coating thicknesses were tested, and comparisons with the rotating bending fatigue data from electroplated Cd specimens were performed. Experimental results differentiated the effects of the various coatings on the AISI 4340 steel behaviour when submitted to fatigue testing and the influence of coating thickness on the fatigue strength.

An investigation on sliding wear behavior of PVD coatings

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Temporal and spatial variability in the macrozoobenthic community along a salinity gradient in the Castillos Lagoon (Uruguay)

The macrozoobenthic community of the Castillos Lagoon system (East Coast of Uruguay) was sampled during autumn, winter, spring and summer of 1991, in order to describe the community structure and the spatial and temporal patterns of distribution. Eleven sampling stations were distributed along a salinity gradient in a north-south direction (8 replicates were collected at each station). The maximum density of organisms was found at the central part of the lagoon (stations 6 and 7) where the bivalve Erodona mactroides and gastropod Heleobia australis were dominants. No significant correlation between the overall abundance of organisms and salinity could be demonstrated (r = 0.43, p > 0.1). However, a reduction in organism abundance between the autumn and the summer coincided with a marked drop in salinity. Falling levels of dissolved oxygen could have influenced the decreasing density of organisms (r = 0.75, p < 0.05). Species richness and diversity were correlated (p < 0.1) with salinity but the degree of correlation was not uniformly significant between sampling periods.

Reproductive phenology of Euterpe edulis (Arecaceae) along a gradient in the Atlantic rainforest of Brazil

The palm Euterpe edulis Mart. is one of the dominant tree species in the Atlantic rainforest and considered a key resource for many frugivorous birds. We compared the reproductive phenology of E. edulis in three types of Atlantic rainforest (two lowland forests, restinga and coastal-plain, and a premontane forest) on Cardoso Island (Cananeia, São Paulo, Brazil), aiming to answer the following questions: (i) whether the reproduction of E. edulis is annual and seasonal across the years in the three forest types studied; (ii) what are the environmental factors influencing the reproductive phenology of E. edulis; and (iii) how does the timing of fruiting and fruit production of E. edulis vary among the three forest types? We evaluated the presence of flowers and fruits (immature, unripe and ripe) from August 2001 to July 2004 in 150 individuals (50 per forest), and estimated the number of infructescences with ripe fruits and the production of fruits and seeds by collecting them on the forest floor in the three forest types. Flowering and fruiting of E. edulis were annual and significantly seasonal in the three forest types, with a high synchrony of flowering and medium to low synchrony of fruiting. Flowering peaked in November and December, and immature and unripe fruits peaked in January and March, all during the rainy season. Immature and unripe fruit phases were correlated with the daylength, precipitation and temperature, important factors for fruits development. Ripe fruits peaked in April and May, in the less rainy season, with significant differences in the mean dates among forests. The number of infructescences with ripe fruits and the biomass of fruits and seeds collected on the ground also differed significantly among the forest types, being greater in the restinga and coastal plain forests, respectively. Differences in productivity were related to palm density in each area and the soil fertility. The complementary fruiting pattern of E. edulis in the forests studied may affect the distribution and abundance of certain frugivorous bird species that feed on their fruits.

Variation in liana abundance and biomass along an elevational gradient in the tropical Atlantic Forest (Brazil)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Seed dispersal and predation in the endemic Atlantic rainforest palm Astrocaryum aculeatissimum across a gradient of seed disperser abundance

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Changes in ichthyofauna composition along a gradient from clearwaters to blackwaters in coastal streams of Atlantic forest (southeastern Brazil) in relation to environmental variables

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

NONDEGENERATE UMBILICS, THE PATH FORMULATION and GRADIENT BIFURCATION PROBLEMS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Fish community structure along a conservation gradient in Bodoquena Plateau streams, central West of Brazil.

Aim: To investigate whether composition and structure of stream ichthyofauna vary along the conservation gradient in the Bodoquena Plateau; Methods: Standardized sampling was performed in nine stream stretches (three references, three in the pasture, and three in urban areas), each 80 m long, in April, May and June/08; Results: A quantity of 8,102 individuals representing 36 species was collected. There were no significant differences with respect to absolute species richness among stretches. Urban stretches were more similar to each other than the other two groups, both regarding species composition and abundance. A set of six species was considered an indicator of reference stretches, whereas two were of pasture stretches and four of urban stretches. Poecilia reticulata and Corydoras aeneus, occurring only in urban stretches, were unique in showing the maximum values in the indicator species analysis; Conclusions: Results indicate changes in the ichthyofauna with urbanized surrounding water courses. The presence and abundance of Poecilia reticulata and Corydoras aeneus may indicate the quality loss of these environments.

High-velocity oxyfuel Cr3C2-NiCr replacing hard chromium coatings

Comparative wear and corrosion properties of Cr3C2-NiCr (CC-TS) (a high-velocity oxyfuel [HVOF]) and hard chromium (HC) coating's obtained on a steel substrate have been studied. The structural characterization was done before and after measurements by optical microscopy, scanning electron microscopy, and scanning white light interferometry. Wear and corrosion properties were evaluated by ball on disk (ASTM G99-90), rubber wheel (ASTM G65-91), and electrochemical measurements of open circuit and polarization curves. The best corrosion and wear resistance was for the CC-TS obtained by HVOF. The open-circuit potential values measured for both samples after 18 h of immersion we're: -0.240 and -0.550 V, respectively, for CC-TS and HC, versus Ag/AgCl,KClsat. Three orders of magnitude lower volume loss were found for CC-TS (HVOF) after friction tests compared with HC.

Influence of spraying parameters on the electrochemical behaviour of HVOF thermally sprayed stainless steel coatings in 3.4% NaCl

Stainless steel coatings obtained by High Velocity Oxygen Fuel (HVOF) were characterized using optical (OM) and scanning electron microscopy (SEM), electron probe micro-analysis, X-ray diffraction (XRD), open-circuit potential (E-OC) measurements, electrochemical impedance spectroscopy (EIS) and polarisation tests. Differences among coated steels were mainly related with the gun-substrate distance parameter (310 nm for samples A and B and 260 min for C and D). The open-circuit potential values measured for all the samples after 18 h of immersion in aerated and unstirred 3.4% NaCl solution were: - 0.334, - 0.360, - 0.379 and - 0.412 V vs. Ag/AgCl,KClsat. for samples A to D, respectively. For EIS measurements, Nyquist plots showed higher capacitive semi-circle for samples sprayed at longer distance, indicating higher corrosion resistance in NaCl solution. (c) 2005 Elsevier B.V. All rights reserved.

The influence of gun transverse speed on electrochemical behaviour of thermally sprayed Cr3C2-NiCr coatings in 0.5 M H2SO4 solution

In the present study, different types of 75% Cr3C2-25% NiCr coatings were applied on a steel substrate by means of high velocity oxygen fuel spraying (HVOF), and studied using ac and dc electrochemical measurements in an aerated and unstirred 0.5 M H2SO4 solution. Structural characterization was determined before and after electrochemical tests. Differences between all sprayed systems are related to the gun transverse speed and number of deposited layers, which strongly affected the electrochemical characteristics of the coated steels. The coating obtained with a higher torch speed showed better resistance against corrosion. The electrochemical impedance results were analyzed using an equivalent circuit where porosity of the coatings and substrate oxidation were considered. (C) 2003 Elsevier Ltd. All rights reserved.

Electrochemical behavior of thermally sprayed stainless steel coatings in 3.4% NaCl solution

Four types of stainless steel coatings prepared by a high velocity oxy-fuel spraying system (HVOF) were studied. Differences among coated steels were related to the spraying parameters, which influenced the behavior of the samples against the corrosion. The electrochemical behavior of the stainless steel coatings was strongly influenced by porosity, the presence of micro- and macro-cracks, and also of un-melted particles. Once the electrolyte reached the steel substrate via these defects, the galvanic pair formed between the coating and substrate-accelerated corrosion, leading to the depletion of the coating. (C) 2004 Elsevier Ltd. All rights reserved.

Effects of thickness coating on the electrochemical behaviour of thermal spray Cr3C2-NiCr coatings

Thermally sprayed HVOF coatings are increasingly being used in industrial applications where high wear and corrosion resistance are needed [1,2]. In this paper, electrochemical ac and de experiments were used in order to obtain the corrosion resistance of coated steel with different numbers of Cr3C2-NiCr layers. This work has been performed in order to determine the role of coating thickness in the corrosion behaviour of a steel protected with cermet thermally sprayed coatings. It is known that a thicker layer protects better against corrosion when a metallic coating is evaluated. But cermet coatings, such as Cr3C2-NiCr, contain higher levels of porosity and residual stresses than metallic coatings, which really could influence the corrosion resistance of the deposited layer. Electrochemical measurements, such as Open-Circuit Potential (E-Osubset of), Polarisation Resistance (RP) and Cyclic Voltammetry (CV), were performed in an aerated 3.4 NaCI media (%wt.). Electrochemical Impedance Measurements (EIS) were also done in order to obtain a mechanism that explains the corrosion process. Structural Characterisation was carried out by means of Optical and Scanning Electron Microscopes (OM, SEM) with an Energy Dispersive Spectrometry analyser (EDS). Results show that the corrosion resistance of the complete system is mainly influenced by the substrate behaviour. The application of a higher number of deposited layers did not substantially increase their anticorrosive properties. Stress generation during the spraying deposition process plays an important role in the behaviour of the coated steel against corrosion phenomena. (C) 2002 Elsevier B.V. B.V All rights reserved.

Electrochemical behaviour of thermally sprayed Cr3C2-NiCr coatings in 0.5 M H2SO4 media

The electrochemical behaviour of coated Cr3C2-NiCr steel in aerated 0.5 M H2SO4 solution was studied by means of electrochemical a.c. and d.c. measurements. A complete structural characterization of the coated steel before and after electrochemical tests was also carried out to access the corrosion mechanism of coated steel, electrolyte penetration through the coating, and to confirm the results obtained using electrochemical techniques. Two types of Cr3C2-NiCr coatings produced by a high velocity oxy-fuel spraying system (HVOF) were studied. Differences between coated steels are related to the spraying parameters reflecting their behaviour against corrosion phenomena. The electrochemical behaviour of the coated steel was strongly influenced by porosity and the presence of microcracks in the coating. Once the electrolyte reaches the steel substrate, it corrodes in a galvanic manner resulting in coating detachment from the steel.