Local plastic mechanisms in thin steel plates under in-plane compression

Thin-walled steel plates subjected to in-plane compression develop two types of local plastic mechanism, namely the roof-shaped mechanism and the so-called flip-disc mechanism, but the intriguing question of why two mechanisms should develop was not answered until recently. It was considered that the location of first yield point shifted from the centre of the plate to the midpoint of the longitudinal edge depending on the b/t ratio, imperfection level, and yield stress of steel, which then decided the type of mechanism. This paper has verified this hypothesis using analysis and laboratory experiments. An elastic analysis using Galerkin's method to solve Marguerre's equations was first used to determine the first yield point, based on which the local plastic mechanism/imperfection tolerance tables have been developed which give the type of mechanism as a function of b/t ratio, imperfection level and yield stress of steel. Laboratory experiments of thin-walled columns verified the imperfection tolerance tables and thus indirectly the hypothesis. Elastic and rigid-plastic curves were them used to predict the effect on the ultimate load due to the change of mechanism. A finite element analysis of selected cases also confirmed the results from simple analyses and experiments.

Removal of bisphenol A from wastewater by Ca-montmorillonite modified with selected surfactants

Organo Arizona SAz-2 Ca-montmorillonite was prepared with different surfactant (DDTMA and HDTMA) loadings through direct ion exchange. The structural properties of the prepared organoclays were characterized by XRD and BET instruments. Batch experiments were carried out on the adsorption of bisphenol A (BPA) under different experimental conditions of pH and temperature to determine the optimum adsorption conditions. The hydrophobic phase and positively charged surface created by the loaded surfactant molecules are responsible for the adsorption of BPA. The adsorption of BPA onto organoclays is well described by pseudo-second order kinetic model and the Langmuir isotherm. The maximum adsorption capacity of the organoclays for BPA obtained from a Langmuir isotherm was 151.52 mg/g at 297 K. This value is among the highest values for BPA adsorption compared with other adsorbents. In addition, the adsorption process was spontaneous and exothermic based on the adsorption thermodynamics study. The organoclays intercalated with longer chain surfactant molecules possessed a greater adsorption capacity for BPA even under alkaline conditions. This process provides a pathway for the removal of BPA from contaminated waters.

Experimental studies of hollow flange channel beams subject to combined bending and shear actions

This paper presents the details of an experimental study of a cold-formed steel hollow flange channel beam known as LiteSteel Beam (LSB) subject to combined bending and shear actions. The LSB sections are produced by a patented manufacturing process involving simultaneous cold-forming and electric resistance welding. Due to the geometry of the LSB, as well as its unique residual stress characteristics and initial geometric imperfections resultant of manufacturing processes, much of the existing research for common cold-formed steel sections is not directly applicable to LSB. Experimental and numerical studies have been carried out to evaluate the behaviour and design of LSBs subject to pure bending actions and predominant shear actions. To date, however, no investigation has been conducted into the strength of LSB sections under combined bending and shear actions. Combined bending and shear is especially prevalent at the supports of continuous span and cantilever beams, where the interaction of high shear force and bending moment can reduce the capacity of a section to well below that for the same section subject only to pure shear or moment. Hence experimental studies were conducted to assess the combined bending and shear behaviour and strengths of LSBs. Eighteen tests were conducted and the results were compared with current AS/NZS 4600 and AS 4100 design rules. AS/NZS 4600 design rules were shown to grossly underestimate the combined bending and shear capacities of LSBs and hence two lower bound design equations were proposed based on experimental results. Use of these equations will significantly improve the confidence and cost-effectiveness of designing LSBs for combined bending and shear actions.

Application of texture analysis in tear film surface assessment based on videokeratoscopy

Purpose Videokeratoscopy images can be used for the non-invasive assessment of the tear film. In this work the applicability of an image processing technique, textural-analysis, for the assessment of the tear film in Placido disc images has been investigated. Methods In the presence of tear film thinning/break-up, the reflected pattern from the videokeratoscope is disturbed in the region of tear film disruption. Thus, the Placido pattern carries information about the stability of the underlying tear film. By characterizing the pattern regularity, the tear film quality can be inferred. In this paper, a textural features approach is used to process the Placido images. This method provides a set of texture features from which an estimate of the tear film quality can be obtained. The method is tested for the detection of dry eye in a retrospective dataset from 34 subjects (22-normal and 12-dry eye), with measurements taken under suppressed blinking conditions. Results To assess the capability of each texture-feature to discriminate dry eye from normal subjects, the receiver operating curve (ROC) was calculated and the area under the curve (AUC), specificity and sensitivity extracted. For the different features examined, the AUC value ranged from 0.77 to 0.82, while the sensitivity typically showed values above 0.9 and the specificity showed values around 0.6. Overall, the estimated ROCs indicate that the proposed technique provides good discrimination performance. Conclusions Texture analysis of videokeratoscopy images is applicable to study tear film anomalies in dry eye subjects. The proposed technique appears to have demonstrated its clinical relevance and utility.

Risk factors for ocular surface squamous neoplasia recurrence after treatment with topical mitomycin C and interferon alpha-2b

Purpose To determine the rate of recurrence and associated risk factors following the use of mitomycin C (MMC) and/or interferon alpha-2b (IFN) for management of non-invasive ocular surface squamous neoplasia (OSSN). Design Retrospective non-comparative interventional case series. Methods Clinical practice setting of 135 patients treated consecutively with topical MMC (0.4 mg/mL) and/or IFN (1 million units/mL) for OSSN observed for clinical recurrence. Results Clinical recurrences were diagnosed in 19 of 135 (14.1%) eyes following topical treatment. The mean time to recurrence was 17.2 months (range 4 - 61) with 14 (73.7%) recurring within a two year period. There was no greater risk of recurrence identified for variables including lesion size, lesion location, gender, age, treatment type or duration. Post-hoc log-Rank pairwise comparisons revealed that lesions initially treated using surgery alone had significantly reduced time to recurrence (21.1 ± 5.6 months) compared to previous topical treatment with MMC (with or without surgery) (29.6 ± 4.7 months) (p = 0.04) and primary OSSN (23.2 ± 1.8 months) (p = 0.09). Conclusions Topical MMC and IFN are an effective treatment modality for a wide range of non-invasive OSSN. Topical therapy avoids the morbidity of excisional surgery with equivalent or reduced recurrence rates and should be considered as primary therapy.

Research trends of post disaster reconstruction : the past and the future

Natural disasters can have adverse effect on human lives. To raise the awareness of research and better combat future events, it is important to identify recent research trends in the area of post disaster reconstruction (PDR). The authors used a three-round literature review strategy to study journal papers published in the last decade that are related to PDR with specific conditions using the Scopus search engine. A wide range of PDR related papers from a general perspective was examined in the first two rounds while the final round established 88 papers as target publications through visual examination of the abstracts, keywords and as necessary, main texts. These papers were analysed in terms of research origins, active researchers, research organisations, most cited papers, regional concerns, major themes and deliverables, for clues of the past trends and future directions. The need for appropriate PDR research is increasingly recognised. The publication number multiplied 5 times from 2002 to 2012. For PDR research with a construction perspective, the increase is sixfold. Developing countries such as those in Asia attract almost 50% researchers' attention for regional concerns while the US is the single most concentrated (24%) country. Africa is hardly represented. Researchers in developed countries lead in worldwide PDR research. This contrasts to the need for expertise in developing countries. Past works focused on waste management, stakeholder analysis, resourcing, infrastructure issue, resilience and vulnerability, reconstruction approach, sustainable reconstruction and governance issues. Future research should respond to resourcing, integrated development, sustainability and resilience building to cover the gaps. By means of a holistic summary and structured analysis of key patterns, the authors hope to provide a streamlined access to existing research findings and make predictions of future trends. They also hope to encourage a more holistic approach to PDR research and international collaborations.

Visibility-related characteristics of crashes involving bicyclists and motor vehicles – Responses from an online questionnaire study

Bicyclists are among the most vulnerable of road users, with high fatal crash rates. Although visibility aids have been widely advocated to help prevent bicycle-vehicle conflicts, to date no study has investigated, among crash-involved cyclists, the kind of visibility aids they were using at the time of the crash. This study undertook a detailed investigation of visibility factors involved in bicyclist-motor-vehicle crashes. We surveyed 184 bicyclists (predominantly from Australia via internet cycling forums) who had been involved in motor vehicle collisions regarding the perceived cause of the collision, ambient weather and general visibility, as well as the clothing and bicycle lights used by the bicyclist. Over a third of the crashes occurred in low light levels (dawn, dusk or night-time), which is disproportionate given that only a small proportion of bicyclists typically ride at these times. Importantly, 19% of these bicyclists reported not using bicycle lights at the time of the crash, and only 34% were wearing reflective clothing. Only two participants (of 184) nominated bicyclist visibility as the cause of the crash: 61% attributed the crash to driver inattention. These findings demonstrate that crash-involved bicyclists tend to under-rate and under-utilise visibility aids as a means of improving their safety.

Influence of drying conditions on the moisture diffusion and fluidization quality during multi-stage fluidized bed drying of bovine intestine for pet food

In order to establish the influence of the drying air characteristics on the drying performance and fluidization quality of bovine intestine for pet food, several drying tests have been carried out in a laboratory scale heat pump assisted fluid bed dryer. Bovine intestine samples were heat pump fluidized bed dried at atmospheric pressure and at temperatures below and above the materials freezing points, equipped with a continuous monitoring system. The investigation of the drying characteristics have been conducted in the temperature range −10 to 25 ◦C and the airflow in the range 1.5–2.5 m/s. Some experiments were conducted as single temperature drying experiments and others as two stage drying experiments employing two temperatures. An Arrhenius-type equation was used to interpret the influence of the drying air temperature on the effective diffusivity, calculated with the method of slopes in terms of energy activation, and this was found to be sensitive to the temperature. The effective diffusion coefficient of moisture transfer was determined by the Fickian method using uni-dimensional moisture movement in both moisture, removal by evaporation and combined sublimation and evaporation. Correlations expressing the effective moisture diffusivity and drying temperature are reported. Bovine particles were characterized according to the Geldart classification and the minimum fluidization velocity was calculated using the Ergun Equation and generalized equation for all drying conditions at the beginning and end of the trials. Walli’s model was used to categorize stability of the fluidization at the beginning and end of the dryingv for each trial. The determined Walli’s values were positive at the beginning and end of all trials indicating stable fluidization at the beginning and end for each drying condition.

Does it matter whether friends, parents, or peers drink walk? Identifying which normative influences predict young pedestrian's decisions to walk while intoxicated

Drink walking, that is walking in a public place while intoxicated, is associated with increased risk of injury and fatality. Young people and males are especially prone to engaging in this behaviour, yet little is known about the factors associated with individual’s decisions to drink walk. The present research explores the role of different normative influences (friendship group norm, parent group norm, university peer group norm) and perceived risk, within an extended theory of planned behaviour (TPB) framework, in predicting young people’s self-reported drink walking intentions. One hundred and eighteen young people (aged 17-25 years) completed a survey including sociodemographic measures and extended TPB measures related to drink walking. Overall the extended TPB explained 72.8% of the variance in young people’s intentions to drink walk in the next six months with attitude, perceived behavioural control, friendship group norm, and gender (male) emerging as significant predictors. Males, as compared with females, had higher intentions to drink walk and lower perceptions of risk regarding drink walking. Together, these findings provide a clearer indication of the salient normative influences and gender differences in young pedestrian’s decisions to walk while intoxicated. Such findings can be used to inform future interventions designed to reduce injuries and fatalities associated with drink walking.

Learning about being effective mentors : professional learning communities and mentoring

This study aimed to explore experienced mentors’ understandings about professional learning communities (PLCs), mentoring and leadership. This research analyses audio-taped transcripts and written responses from 27 experienced mentors who operate in varied roles (e.g., university academics, school executives, teachers, learning support personnel). Findings indicated that PLCs can provide professional renewal for existing teachers and that mentoring within PLCs can further advance knowledge about effective practices. PLCs can include other staff members and key stakeholders (e.g., preservice teachers, teacher aides) who can contribute to the learning within the group. Mentoring and PLCs can be cost-effective strategic levers for advancing professional knowledge.

Commencing nursing students' perceptions and anxiety of bioscience

It is known that bioscience is perceived to be difficult and causes anxiety within undergraduate nursing students; yet, commencing students' perceptions of bioscience is not known. Therefore, the aim of this study was to ascertain incoming students' perceptions, knowledge and approaches to learning bioscience. Incoming students to the Bachelor of Nursing completed a questionnaire prior to undertaking bioscience. Two hundred and seventy three students completed the questionnaire that explored their expectations, preconceptions of bioscience content, approaches to learning bioscience, and relationship to clinical practice in the context of biosciences. Participant ages ranged from 17 to 53 (mean 23 years), and 78% of students had completed at least one secondary school science subject, of which 60% had studied biology. Overall, students' preconceptions included anxiety about studying bioscience, bioscience being difficult and harder than nursing subjects, and that more content will be required for bioscience than nursing subjects. Analysis using ANOVA revealed the relationships for secondary school science and age on student responses. A significant effect of secondary school science was found for science in school being advantageous for bioscience (p = 0.010), understanding what bioscience entails (p = 0.002), needing to study science prior to the start of the semester (p = 0.009), and that bioscience is considered difficult (p = 0.029). A significant effect of age was found for exams being more difficult than other assessments (p = 0.000) and for being able to see the relevance of nursing when reaching the workplace (p = 0.011). The findings also indicated that perceptions and associated anxieties related to bioscience were present in commencing students, similar to those which have been reported previously in established student groups. This strongly suggests that the faculty should attempt to dispel preconceptions about bioscience and target improved supports to facilitate the transition of students into the commencement of bioscience for nursing students.

Beliefs underlying the intention to donate again among first-time blood donors who experience a mild adverse event

Using the belief basis of the theory of planned behavior (TPB), the current study explored the rate of mild reactions reported by donors in relation to their first donation and the intention and beliefs of those donors with regard to returning to donate again. A high proportion of first-time donors indicated that they had experienced a reaction to blood donation. Further, donors who reacted were less likely to intend to return to donate. Regression analyses suggested that targeting different beliefs for those donors who had and had not reacted would yield most benefit in bolstering donors’ intentions to remain donating. The findings provide insight into those messages that could be communicated via the mass media or in targeted communications to retain first-time donors who have experienced a mild vasovagal reaction.

Recent developments and research needs in modeling lane changing

This paper comprehensively reviews recent developments in modeling lane-changing behavior. The major lane changing models in the literature are categorized into two groups: models that aim to capture the lane changing decision-making process, and models that aim to quantify the impact of lane changing behavior on surrounding vehicles. The methodologies and important features (including their limitations) of representative models in each category are outlined and discussed. Future research needs are determined.

On the periodicity of traffic oscillations and capacity drop : the role of driver characteristics

This paper shows that traffic hysteresis, a manifestation of driver characteristics, has a profound impact on the development of traffic oscillations and the bottleneck discharge rate. Findings suggest that aggressive driver behavior (with small response times and jammed spacing) leads to spontaneous formations of stop-and-go disturbances. Furthermore, the aggressive behavior, coupled with a late response to adopt less aggressive behavior, generates large hysteresis that leads to oscillations’ transformation from localized to substantial disturbances and growth. The larger the magnitude of hysteresis is, the larger the growth is. Our finding also suggests that the bottleneck discharge rate can diminish by 8-23% when driver adopts a less aggressive reaction to a disturbance (characterized by a larger response time). This finding is particularly notable since lane-changes have been believed to be the major cause of a reduction in bottleneck discharge rate.

Public acceptance towards congestion charge : a case study of Brisbane

This paper investigates public acceptance towards congestion charge in Australia by taking Brisbane as a case study. Public acceptance to congestion charge has often been investigated in the literature. However, few were in the context of an Australian city. This paper fills the gap. A face-to-face survey was conducted to solicit public opinions on the congestion charge, should a congestion charge scheme be implemented in the Brisbane City area. The survey data were analysed to pinpoint important factors relevant to people’s attitudes towards congestion charge and to measure their relationships. Main findings from our analysis are: (1) the residents’ attitudes towards congestion charge differ by genders and by user groups of transport modes; (2) for each of the three groups (i.e., the auto users, the transit riders, and the whole participants), a positive and stable correlation was found between a participant’s attitude towards congestion charge and the effectiveness of congestion charge on reducing traffic congestion. A negative and stable correlation was also found for all three groups between a participant’s attitude towards congestion charge and congestion charge’s negative impact on the attractiveness of working in the city; (3) the auto users tended to be more sceptical about the service capacity of existing transit systems in coping with extra passengers induced by the implementation of congestion charge; and (4) for people with high income, introducing the congestion charge may have no impact on their travelling to the city.