The Influence of Process Conditions on the Deresination Efficiency in Mechanical Pulp Washing

The aim of this thesis was to produce information for the estimation of the flow balance of wood resin in mechanical pulping and to demonstrate the possibilities for improving the efficiency of deresination in practice. It was observed that chemical changes in wood resin take place only during peroxide bleaching, a significant amount of water dispersed wood resin is retained in the pulp mat during dewatering and the amount of wood resin in the solid phase of the process filtrates is very small. On the basis of this information there exist three parameters related to behaviour of wood resin that determine the flow balance in the process: 1. The liberation of wood resin to the pulp water phase 2. Theretention of water dispersed wood resin in dewatering 3. The proportion of wood resin degraded in the peroxide bleaching The effect of different factors on these parameters was evaluated with the help of laboratory studies and a literature survey. Also, information related to the values of these parameters in existing processes was obtained in mill measurements. With the help of this information, it was possible to evaluate the deresination efficiency and the effect of different factors on this efficiency in a pulping plant that produced low-freeness mechanical pulp. This evaluation showed that the wood resin content of mechanical pulp can be significantly decreased if there exists, in the process, a peroxide bleaching and subsequent washing stage. In the case of an optimal process configuration, as high as a 85 percent deresination efficiency seems to be possible with a water usage level of 8 m3/o.d.t.

Supply chain integration: studies on linking customer responsiveness and operational efficiency in logistics policy planning

Abstract The research problem in the thesis deals with improving the responsiveness and efficiency of logistics service processes between a supplier and its customers. The improvement can be sought by customizing the services and increasing the coordination of activities between the different parties in the supply chain. It is argued that to achieve coordination the parties have to have connections on several levels. In the framework employed in this research, three contexts are conceptualized at which the linkages can be planned: 1) the service policy context, 2) the process coordination context, and 3) the relationship management context. The service policy context consists of the planning methods by which a supplier analyzes its customers' logistics requirements and matches them with its own operational environment and efficiency requirements. The main conclusion related to the service policy context is that it is important to have a balanced selection of both customer-related and supplier-related factors in the analysis. This way, while the operational efficiency is planned a sufficient level of service for the most important customers is assured. This kind of policy planning involves taking multiple variables into the analysis, and there is a need to develop better tools for this purpose. Some new approaches to deal with this are presented in the thesis.The process coordination context and the relationship management context deal with the issues of how the implementation of the planned service policies can be facilitated in an inter-organizational environment. Process coordination includes typically such mechanisms as control rules, standard procedures and programs, but inhighly demanding circumstances more integrative coordination mechanisms may be necessary. In the thesis the coordination problems in third-party logistics relationship are used as an example of such an environment. Relationship management deals with issues of how separate companies organize their relationships to improve the coordination of their common processes. The main implication related to logistics planning is that by integrating further at the relationship level, companies can facilitate the use of the most efficient coordination mechanisms and thereby improve the implementation of the selected logistics service policies. In the thesis, a case of a logistics outsourcing relationship is used to demonstrate the need to address the relationship issues between the service provider andthe service buyer before the outsourcing can be done.The dissertation consists of eight research articles and a summarizing report. The principal emphasis in the articles is on the service policy planning context, which is the main theme of six articles. Coordination and relationship issues are specifically addressed in two of the papers.

A novel approachfor assessing the fatigue strength of ultrasonic impact treated welded structures.

It is commonly observed that complex fabricated structures subject tofatigue loading fail at the welded joints. Some problems can be corrected by proper detail design but fatigue performance can also be improved using post-weld improvement methods. In general, improvement methods can be divided into two main groups: weld geometry modification methods and residual stress modification methods. The former remove weld toe defects and/or reduce the stress concentrationwhile the latter introduce compressive stress fields in the area where fatigue cracks are likely to initiate. Ultrasonic impact treatment (UIT) is a novel post-weld treatment method that influences both the residual stress distribution andimproves the local geometry of the weld. The structural fatigue strength of non-load carrying attachments in the as-welded condition has been experimentally compared to the structural fatigue strength of ultrasonic impact treated welds. Longitudinal attachment specimens made of two thicknesses of steel S355 J0 have been tested for determining the efficiency of ultrasonic impacttreatment. Treated welds were found to have about 50% greater structural fatigue strength, when the slope of the S-N-curve is three. High mean stress fatigue testing based on the Ohta-method decreased the degree of weld improvement only 19%. This indicated that the method could be also applied for large fabricated structures operating under high reactive residual stresses equilibrated within the volume of the structure. The thickness of specimens has no significant effect tothe structural fatigue strength. The fatigue class difference between 5 mm and 8 mm specimen was only 8%. It was hypothesized that the UIT method added a significant crack initiation period to the total fatigue life of the welded joints. Crack initiation life was estimated by a local strain approach. Material parameters were defined using a modified Uniform Material Law developed in Germany. Finite element analysis and X-ray diffraction were used to define, respectively, the stress concentration and mean stress. The theoretical fatigue life was found to have good accuracy comparing to experimental fatigue tests.The predictive behaviour of the local strain approach combined with the uniformmaterial law was excellent for the joint types and conditions studied in this work.

Dynamics of Appropriability - Finding a Balance between Efficiency and Strength in the Appropriability Regime

Building and sustaining competitive advantage through the creation of market imperfections is challenging in a constantly changing business environment - particularly since the sources of such advantages are increasingly knowledge-based. Facilitated by improved networks and communication, knowledge spills over to competitors more easily than before,thus creating an appropriability problem: the inability of an innovating firm to utilize its innovations commercially. Consequently, as the importance of intellectual assets increases, their protection also calls for new approaches. Companies have various means of protection at their disposal, and by taking advantage of them they can make intangibles more non-transferable and prevent, or at leastdelay, imitation of their most crucial intellectual assets. However, creating barriers against imitation has another side to it, and the transfer of knowledge in situations requiring knowledge sharing may be unintentionally obstructed. Theaim of this thesis is to increase understanding of how firms can balance knowledge protection and sharing so as to benefit most from their knowledge assets. Thus, knowledge protection is approached through an examination of the appropriability regime of a firm, i.e., the combination of available and effective means ofprotecting innovations, their profitability, and the increased rents due to R&D. A further aim is to provide a broader understanding of the formation and structure of the appropriability regime. The study consists of two parts. The first part introduces the research topic and the overall results of the study, and the second part consists of six complementary research publications covering various appropriability issues. The thesis contributes to the existing literature in several ways. Although there is a wide range of prior research on appropriability issues, a lot of it is restricted either to the study of individual appropriability mechanisms, or to comparing certain features of them. These approaches are combined, and the relevant theoretical concepts are clarified and developed. In addition, the thesis provides empirical evidence of the formation of the appropriability regime, which is consequently presented as an adaptive process. Thus, a framework is provided that better corresponds to the complex reality of the current business environment.

Effect of water velocity on the uptake of polychlorinatedd biphenyls (PCBs) by silicone rubber (SR) and low-density polyethylene (LDPE) passive samplers: an assessment of the efficiency of performance reference compounds (PRCs) in river-like flow conditions

One aim of this study is to determine the impact of water velocity on the uptake of indicator polychlorinated biphenyls (iPCBs) by silicone rubber (SR) and low-density polyethylene (LDPE) passive samplers. A second aim is to assess the efficiency of performance reference compounds (PRCs) to correct for the impact of water velocity. SR and LDPE samplers were spiked with 11 or 12 PRCs and exposed for 6 weeks to four different velocities (in the range of 1.6 to 37.7 cm s−1) in river-like flow conditions using a channel system supplied with river water. A relationship between velocity and the uptakewas found for each iPCB and enables to determine expected changes in the uptake due to velocity variations. For both samplers, velocity increases from 2 to 10 cm s−1, 30 cm s−1 (interpolated data) and 100 cm s−1 (extrapolated data) lead to increases of the uptake which do not exceed a factor of 2, 3 and 4.5, respectively. Results also showed that the influence of velocity decreased with increasing the octanol-water coefficient partition (log Kow) of iPCBs when SR is used whereas the opposite effect was observed for LDPE. Time-weighted average (TWA) concentrations of iPCBs in water were calculated from iPCB uptake and PRC release. These calculations were performed using either a single PRC or all the PRCs. The efficiency of PRCs to correct the impact of velocity was assessed by comparing the TWA concentrations obtained at the four tested velocities. For SR, a good agreement was found among the four TWA concentrations with both methods (average RSD b 10%). Also for LDPE, PRCs offered a good correction of the impact of water velocity (average RSD of about 10 to 20%). These results contribute to the process of acceptance of passive sampling in routine regulatory monitoring programs.

Justice and Court Administrations, Their Workings and Efficiency in Switzerland : Aspects of Sentencing And Its Outcome In Swiss Cantons

The comparison of the operations of the administration of justice among cantons shows on one side large differences in the three major types of sentencing, in the use of pre-trial detention and the unsuspended prison sanction. When combined, one finds however very weak relationships when considering absolute, percentage or weighted results. On the other side, the outcome of these different policies is much paradoxical as there are no differences when comparing recidivism rates among cantons, despite strong differences in the use of pre-trial detention and the sentencing with prison sanctions. The paradoxical outcome of crime policies in terms of recidivism - e.g. the absence of differences of the outcome based on sanctions in the domain of less severe delinquency - suggests the need for more empirically informed crime policies. The role of justice administrators could be to participate in the dissemination of those findings as well as the dissemination of best practices among cantons with regard to outcomes and the use of resources - especially with consideration to the use of the prison sanction as it is the most costly and the most inefficient of all sanctions. Furthermore, the observance of the principle of equality before the law would be most likely be promoted.

Expanding the Mutation Spectrum Affecting αIIbβ3 Integrin in Glanzmann Thrombasthenia: Screening of the ITGA2B and ITGB3 Genes in a Large International Cohort.

We report the largest international study on Glanzmann thrombasthenia (GT), an inherited bleeding disorder where defects of the ITGA2B and ITGB3 genes cause quantitative or qualitative defects of the αIIbβ3 integrin, a key mediator of platelet aggregation. Sequencing of the coding regions and splice sites of both genes in members of 76 affected families identified 78 genetic variants (55 novel) suspected to cause GT. Four large deletions or duplications were found by quantitative real-time PCR. Families with mutations in either gene were indistinguishable in terms of bleeding severity that varied even among siblings. Families were grouped into type I and the rarer type II or variant forms with residual αIIbβ3 expression. Variant forms helped identify genes encoding proteins mediating integrin activation. Splicing defects and stop codons were common for both ITGA2B and ITGB3 and essentially led to a reduced or absent αIIbβ3 expression; included was a heterozygous c.1440-13_c.1440-1del in intron 14 of ITGA2B causing exon skipping in seven unrelated families. Molecular modeling revealed how many missense mutations induced subtle changes in αIIb and β3 domain structure across both subunits, thereby interfering with integrin maturation and/or function. Our study extends knowledge of GT and the pathophysiology of an integrin.

Conditional equilibrium constants in multicomponent heterogeneous adsorption: The conditional affinity spectrum

The concept of conditional stability constant is extended to the competitive binding of small molecules to heterogeneous surfaces or macromolecules via the introduction of the conditional affinity spectrum (CAS). The CAS describes the distribution of effective binding energies experienced by one complexing agent at a fixed concentration of the rest. We show that, when the multicomponent system can be described in terms of an underlying affinity spectrum [integral equation (IE) approach], the system can always be characterized by means of a CAS. The thermodynamic properties of the CAS and its dependence on the concentration of the rest of components are discussed. In the context of metal/proton competition, analytical expressions for the mean (conditional average affinity) and the variance (conditional heterogeneity) of the CAS as functions of pH are reported and their physical interpretation discussed. Furthermore, we show that the dependence of the CAS variance on pH allows for the analytical determination of the correlation coefficient between the binding energies of the metal and the proton. Nonideal competitive adsorption isotherm and Frumkin isotherms are used to illustrate the results of this work. Finally, the possibility of using CAS when the IE approach does not apply (for instance, when multidentate binding is present) is explored. © 2006 American Institute of Physics.

Complex syntax in autism spectrum disorders: a study of relative clauses.

BACKGROUND: The few studies that have evaluated syntax in autism spectrum disorder (ASD) have yielded conflicting findings: some suggest that once matched on mental age, ASD and typically developing controls do not differ for grammar, while others report that morphosyntactic deficits are independent of cognitive skills in ASD. There is a need for a better understanding of syntax in ASD and its relation to, or dissociation from, nonverbal abilities. AIMS: Syntax in ASD was assessed by evaluating subject and object relative clause comprehension in adolescents and adults diagnosed with ASD with a performance IQ within the normal range, and with or without a history of language delay. METHODS & PROCEDURES: Twenty-eight participants with ASD (mean age 21.8) and 28 age-matched controls (mean age 22.07) were required to point to a character designated by relative clauses that varied in syntactic complexity. OUTCOMES & RESULTS: Scores indicate that participants with ASD regardless of the language development history perform significantly worse than age-matched controls with object relative clauses. In addition, participants with ASD with a history of language delay (diagnosed with high-functioning autism in the DSM-IV-TR) perform worse on subject relatives than ASD participants without language delay (diagnosed with Asperger syndrome in the DSM-IV-TR), suggesting that these two groups do not have equivalent linguistic abilities. Performance IQ has a positive impact on the success of the task for the population with ASD. CONCLUSIONS & IMPLICATIONS: This study reveals subtle grammatical difficulties remaining in adult individuals with ASD within normal IQ range as compared with age-matched peers. Even in the absence of a history of language delay in childhood, the results suggest that a slight deficit may nevertheless be present and go undetected by standardized language assessments. Both groups with and without language delay have a similar global performance on relative clause comprehension; however, the study also indicates that the participants with reported language delay show more difficulty with subject relatives than the participants without language delay, suggesting the presence of differences in linguistic abilities between these subgroups of ASD.

Ownership change and banking efficiency in the new EU members

The aim of this study is to analyze how European integration and, especially, changes in ownership, has affected banking efficiency in Central and Eastern European countries which have recently experimented this process more intensely. Using a stochastic frontier approach (SFA) applied to panel data, we have estimated bank efficiency levels in a sample of 189 banks from 12 countries during the period 2000 to 2008 and we have analyzed the influence of some bank characteristics on these efficiency levels. The results show that European integration has significantly improved the cost efficiency of banks in these countries but profit efficiency has significantly decreased. We have found very small differences between different ownership types and only a very small impact of foreign ownership on cost efficiency, showing that the entry of foreign ownership is not enough to explain the significant variations in banking efficiency after the accession.

Diffraction grating couplers milled in Si3N4 rib waveguides with a focused ion beam

Focused ion beam milling is a processing technology which allows flexible direct writing of nanometer scale features efficiently substituting electron beam lithography. No mask need results in ability for patterns writing even on fragile micromechanical devices. In this work we studied the abilities of the tool for fabrication of diffraction grating couplers in silicon nitride waveguides. The gratings were fabricated on a chip with extra fragile cantilevers of sub micron thickness. Optical characterization of the couplers was done using excitation of the waveguides in visible range by focused Gaussian beams of different waist sizes. Influence of Ga+ implantation on the device performance was studied.

Spectral analysis of the angular distribution function of back reflectors for thin film silicon solar cells

Nowadays, one of the most important challenges to enhance the efficiency of thin film silicon solar cells is to increase the short circuit intensity by means of optical confinement methods, such as textured back-reflector structures. In this work, two possible textured structures to be used as back reflectors for n-i-p solar cells have been optically analyzed and compared to a smooth one by using a system which is able to measure the angular distribution function (ADF) of the scattered light in a wide spectral range (350-1000 nm). The accurate analysis of the ADF data corresponding to the reflector structures and to the μc-Si:H films deposited onto them allows the optical losses due to the reflector absorption and its effectiveness in increasing light absorption in the μc-Si:H layer, mainly at long wavelengths, to be quantified.