Design of surface forces apparatus for tribology studies combined with nonlinear optical spectroscopy

We describe the design, calibration, and performance of surface forces apparatus with the capability of illumination of the contact interface for spectroscopic investigation using optical techniques. The apparatus can be placed in the path of a Nd-YAG laser for studies of the linear response or the second harmonic and sum-frequency generation from a material confined between the two surfaces. In addition to the standard fringes of equal chromatic order technique, which we have digitized for accurate and fast analysis, the distance of separation can be measured with a fiber-optic interferometer during spectroscopic measurements (2 Å resolution and 10 ms response time). The sample approach is accomplished through application of a motor drive, piezoelectric actuator, or electromagnetic lever deflection for variable degrees of range, sensitivity, and response time. To demonstrate the operation of the instrument, the stepwise expulsion of discrete layers of octamethylcyclotetrasiloxane from the contact is shown. Lateral forces may also be studied by using piezoelectric bimorphs to induce and direct the motion of one surface.

Blood pressure and LDL-cholesterol targets for prevention of recurrent strokes and cognitive decline in the hypertensive patient: design of the European Society of Hypertension-Chinese Hypertension League Stroke in Hypertension Optimal Treatment randomized trial.

BACKGROUND AND OBJECTIVES: The SBP values to be achieved by antihypertensive therapy in order to maximize reduction of cardiovascular outcomes are unknown; neither is it clear whether in patients with a previous cardiovascular event, the optimal values are lower than in the low-to-moderate risk hypertensive patients, or a more cautious blood pressure (BP) reduction should be obtained. Because of the uncertainty whether 'the lower the better' or the 'J-curve' hypothesis is correct, the European Society of Hypertension and the Chinese Hypertension League have promoted a randomized trial comparing antihypertensive treatment strategies aiming at three different SBP targets in hypertensive patients with a recent stroke or transient ischaemic attack. As the optimal level of low-density lipoprotein cholesterol (LDL-C) level is also unknown in these patients, LDL-C-lowering has been included in the design. PROTOCOL DESIGN: The European Society of Hypertension-Chinese Hypertension League Stroke in Hypertension Optimal Treatment trial is a prospective multinational, randomized trial with a 3 × 2 factorial design comparing: three different SBP targets (1, <145-135; 2, <135-125; 3, <125 mmHg); two different LDL-C targets (target A, 2.8-1.8; target B, <1.8 mmol/l). The trial is to be conducted on 7500 patients aged at least 65 years (2500 in Europe, 5000 in China) with hypertension and a stroke or transient ischaemic attack 1-6 months before randomization. Antihypertensive and statin treatments will be initiated or modified using suitable registered agents chosen by the investigators, in order to maintain patients within the randomized SBP and LDL-C windows. All patients will be followed up every 3 months for BP and every 6 months for LDL-C. Ambulatory BP will be measured yearly. OUTCOMES: Primary outcome is time to stroke (fatal and non-fatal). Important secondary outcomes are: time to first major cardiovascular event; cognitive decline (Montreal Cognitive Assessment) and dementia. All major outcomes will be adjudicated by committees blind to randomized allocation. A Data and Safety Monitoring Board has open access to data and can recommend trial interruption for safety. SAMPLE SIZE CALCULATION: It has been calculated that 925 patients would reach the primary outcome after a mean 4-year follow-up, and this should provide at least 80% power to detect a 25% stroke difference between SBP targets and a 20% difference between LDL-C targets.

I-74 Iowa/Illinois Corridor Study Aesthetic Design Guideline April 6, 2009

The I-74 Aesthetic Design Guideline (ADG) document has two primary goals: To establish and identify an overall design theme To prioritize enhancement opportunities within the framework of corridor elements The recommendations of this report have been developed based on an “unconstrained” framework for future corridor–wide enhancements. Future funding availability, along with the recommendations of this report, will guide the final design process. ADG Future Uses: This document is intended to be used as a reference to future processes in the following ways: Guidance for I-74 final design teams Reference document for future local community redevelopment initiatives Inspiration for identification and development of other I-74 corridor aesthetic enhancement opportunities Process: As illustrated in Figure 1.3, the overall process for corridor aesthetics began traditionally with inventory and identification of potential aesthetic applications. The ADG does not document all the reports and presentations related to these early design stages, but has incorporated these efforts into the design theme, guiding principles and prioritized enhancements shown on the following pages of this report. The I-74 final design phase will incorporate these recommendations into the project. The consultant design team and representatives of the DOTs have worked with the CAAT members to facilitate community input and have helped develop recommendations for improving I-74 corridor aesthetics. CAAT recommendations have been advanced to the I-74 Advisory Committee for review and endorsement. Both DOTs have reviewed the CAAT recommendations and have endorsed the contents of this report. Figure 1.4 illustrates the status of corridor aesthetic design development. As of the date of this report, aesthetic design is approximately 50% complete. Future detailed design, cost evaluation, feasibility and prioritizations all need to occur for this process to be successfully completed.

Design, data management, and population baseline characteristics of the PERFORM magnetic resonance imaging project.

Quantitative information from magnetic resonance imaging (MRI) may substantiate clinical findings and provide additional insight into the mechanism of clinical interventions in therapeutic stroke trials. The PERFORM study is exploring the efficacy of terutroban versus aspirin for secondary prevention in patients with a history of ischemic stroke. We report on the design of an exploratory longitudinal MRI follow-up study that was performed in a subgroup of the PERFORM trial. An international multi-centre longitudinal follow-up MRI study was designed for different MR systems employing safety and efficacy readouts: new T2 lesions, new DWI lesions, whole brain volume change, hippocampal volume change, changes in tissue microstructure as depicted by mean diffusivity and fractional anisotropy, vessel patency on MR angiography, and the presence of and development of new microbleeds. A total of 1,056 patients (men and women ≥ 55 years) were included. The data analysis included 3D reformation, image registration of different contrasts, tissue segmentation, and automated lesion detection. This large international multi-centre study demonstrates how new MRI readouts can be used to provide key information on the evolution of cerebral tissue lesions and within the macrovasculature after atherothrombotic stroke in a large sample of patients.

Task 4: Testing Iowa Portland Cement Concrete Mixtures for the AASHTO Mechanistic-Empirical Pavement Design Procedure, May 2008

The present research project was designed to identify the typical Iowa material input values that are required by the Mechanistic-Empirical Pavement Design Guide (MEPDG) for the Level 3 concrete pavement design. It was also designed to investigate the existing equations that might be used to predict Iowa pavement concrete for the Level 2 pavement design. In this project, over 20,000 data were collected from the Iowa Department of Transportation (DOT) and other sources. These data, most of which were concrete compressive strength, slump, air content, and unit weight data, were synthesized and their statistical parameters (such as the mean values and standard variations) were analyzed. Based on the analyses, the typical input values of Iowa pavement concrete, such as 28-day compressive strength (f’c), splitting tensile strength (fsp), elastic modulus (Ec), and modulus of rupture (MOR), were evaluated. The study indicates that the 28-day MOR of Iowa concrete is 646 + 51 psi, very close to the MEPDG default value (650 psi). The 28-day Ec of Iowa concrete (based only on two available data of the Iowa Curling and Warping project) is 4.82 + 0.28x106 psi, which is quite different from the MEPDG default value (3.93 x106 psi); therefore, the researchers recommend re-evaluating after more Iowa test data become available. The drying shrinkage (εc) of a typical Iowa concrete (C-3WR-C20 mix) was tested at Concrete Technology Laboratory (CTL). The test results show that the ultimate shrinkage of the concrete is about 454 microstrain and the time for the concrete to reach 50% of ultimate shrinkage is at 32 days; both of these values are very close to the MEPDG default values. The comparison of the Iowa test data and the MEPDG default values, as well as the recommendations on the input values to be used in MEPDG for Iowa PCC pavement design, are summarized in Table 20 of this report. The available equations for predicting the above-mentioned concrete properties were also assembled. The validity of these equations for Iowa concrete materials was examined. Multiple-parameters nonlinear regression analyses, along with the artificial neural network (ANN) method, were employed to investigate the relationships among Iowa concrete material properties and to modify the existing equations so as to be suitable for Iowa concrete materials. However, due to lack of necessary data sets, the relationships between Iowa concrete properties were established based on the limited data from CP Tech Center’s projects and ISU classes only. The researchers suggest that the resulting relationships be used by Iowa pavement design engineers as references only. The present study furthermore indicates that appropriately documenting concrete properties, including flexural strength, elastic modulus, and information on concrete mix design, is essential for updating the typical Iowa material input values and providing rational prediction equations for concrete pavement design in the future.

Discriminant ECOC: a heuristic method for application dependent design of error correcting output codes

We present a heuristic method for learning error correcting output codes matrices based on a hierarchical partition of the class space that maximizes a discriminative criterion. To achieve this goal, the optimal codeword separation is sacrificed in favor of a maximum class discrimination in the partitions. The creation of the hierarchical partition set is performed using a binary tree. As a result, a compact matrix with high discrimination power is obtained. Our method is validated using the UCI database and applied to a real problem, the classification of traffic sign images.

Subclass problem-dependent design for error-correcting output codes

A common way to model multiclass classification problems is by means of Error-Correcting Output Codes (ECOCs). Given a multiclass problem, the ECOC technique designs a code word for each class, where each position of the code identifies the membership of the class for a given binary problem. A classification decision is obtained by assigning the label of the class with the closest code. One of the main requirements of the ECOC design is that the base classifier is capable of splitting each subgroup of classes from each binary problem. However, we cannot guarantee that a linear classifier model convex regions. Furthermore, nonlinear classifiers also fail to manage some type of surfaces. In this paper, we present a novel strategy to model multiclass classification problems using subclass information in the ECOC framework. Complex problems are solved by splitting the original set of classes into subclasses and embedding the binary problems in a problem-dependent ECOC design. Experimental results show that the proposed splitting procedure yields a better performance when the class overlap or the distribution of the training objects conceal the decision boundaries for the base classifier. The results are even more significant when one has a sufficiently large training size.

Low Water Stream Crossing: Design and Construction Recommendations, Decemeber 2001

Most counties have bridges that are no longer adequate, and are faced with large capital expenditure for replacement structures of the same size. In this regard, low water stream crossings (LWSCs) can provide an acceptable, low cost alternative to bridges and culverts on low volume and reduced maintenance level roads. In addition to providing a low cost option for stream crossings, LWSCs have been designed to have the additional benefit of streambed stabilization. Considerable information on the current status of LWSCs in Iowa, along with insight of needs for design assistance, was gained from a survey of county engineers that was conducted as part of this research (Appendix A). Copies of responses and analysis are included in Appendix B. This document provides guidelines for the design of LWSCs. There are three common types of LWSCs: unvented ford, vented ford with pipes, and low water bridges. Selection among these depends on stream geometry, discharge, importance of road, and budget availability. To minimize exposure to tort liability, local agencies using low water stream crossings should consider adopting reasonable selection and design criteria and certainly provide adequate warning of these structures to road users. The design recommendations included in this report for LWSCs provide guidelines and suggestions for local agency reference. Several design examples of design calculations are included in Appendix E.

Low Water Stream Crossing: Design and Construction Recommendations; A Selection and Design Guide, February 2003

Most Iowa counties maintain low volume roads with at least one bridge or culvert that is structurally deficient or obsolete. In some counties the percentage of deficient drainage structures may be as high as 62%. Replacement with structures of similar size would require large capital expenditures that many counties cannot afford. Low water stream crossings (LWSCs) may be an acceptable lowcost alternative in some cases.

Roadway Design Standards for Rural and Suburban Subdivisions Final Report, June 2007

In Iowa, there are currently no uniform design standards for rural and suburban subdivision development roadways. Without uniform design standards, many counties are unable to provide adequate guidance for public facilities, particularly roadways, to be constructed as part of a rural subdivision development. If a developer is not required to install appropriate public improvements or does not do so properly, significant liability and maintenance expenses can be expected, along with the potential for major project costs to correct the situation. Not having uniform design standards for rural and suburban subdivision development improvements in Iowa creates situations where there is potential for inconsistency and confusion. Differences in the way development standards are applied also create incentives or disincentives for developers to initiate subdivision platting in a particular county. With the wide range of standards or lack of standards for local roads in development areas, it is critical that some level of uniformity is created to address equity in development across jurisdictional lines. The standards must be effective in addressing the problem, but they must not be so excessive as to curtail development activities within a local jurisdiction. In order to address the concerns, cities and counties have to work together to identify where growth is going to be focused. Within that long-term growth area, the roadways should be constructed to urban standards to provide an easier transition to traditional urban facilities as the area is developed. Developments outside of the designated growth area should utilize a rural cross section since it is less likely to have concentrated urban development. The developers should be required to develop roadways that are designed for a minimum life of 40 years, and the county should accept dedication of the roadway and be responsible for its maintenance.

Design and Performance Verifcation of Ultra-High Performance Concrete Piles for Deep Foundations Final Report, November 2008

The strategic plan for bridge engineering issued by AASHTO in 2005 identified extending the service life and optimizing structural systems of bridges in the United States as two grand challenges in bridge engineering, with the objective of producing safer bridges that have a minimum service life of 75 years and reduced maintenance cost. Material deterioration was identified as one of the primary challenges to achieving the objective of extended life. In substructural applications (e.g., deep foundations), construction materials such as timber, steel, and concrete are subjected to deterioration due to environmental impacts. Using innovative and new materials for foundation applications makes the AASHTO objective of 75 years service life achievable. Ultra High Performance Concrete (UHPC) with compressive strength of 180 MPa (26,000 psi) and excellent durability has been used in superstructure applications but not in geotechnical and foundation applications. This study explores the use of precast, prestressed UHPC piles in future foundations of bridges and other structures. An H-shaped UHPC section, which is 10-in. (250-mm) deep with weight similar to that of an HP10×57 steel pile, was designed to improve constructability and reduce cost. In this project, instrumented UHPC piles were cast and laboratory and field tests were conducted. Laboratory tests were used to verify the moment-curvature response of UHPC pile section. In the field, two UHPC piles have been successfully driven in glacial till clay soil and load tested under vertical and lateral loads. This report provides a complete set of results for the field investigation conducted on UHPC H-shaped piles. Test results, durability, drivability, and other material advantages over normal concrete and steel indicate that UHPC piles are a viable alternative to achieve the goals of AASHTO strategic plan.

Design and Construction in Fair Housing: Enforcement, Timeless and Practical Suggestion, Spring 2010

In addition to the Fair Housing Act of 1968, other legislation has expanded protection from discrimination for individuals with disabilities, including the Rehabilitation Act of 1973 and the Americans with Disabilities Act of 1990. Notably, the Fair Housing Amendments Act (FHAA), signed into law by Ronald Reagan in 1988, expanded equal housing protection to individuals with disabilities. The legislative history behind the 1988 Amendments notes that one aim of the law was to address both purposeful discrimination as well as what is sometimes unintentional discrimination caused by the design and construction of inaccessible housing.

Faire la ville juste : une analyse "in itinere" de la maîtrise publique d'ouvrage du projet urbain Carré de Soie (métropole lyonnaise)

Dans certaines portions des agglomérations (poches de pauvreté de centre-ville, couronnes suburbaines dégradées, espaces périurbains sans aménité), un cumul entre des inégalités sociales (pauvreté, chômage, etc.) et environnementales (exposition au bruit, aux risques industriels, etc.) peut être observé. La persistance de ces inégalités croisées dans le temps indique une tendance de fond : la capacité d'accéder à un cadre de vie de qualité n'est pas équitablement partagée parmi les individus. Ce constat interroge : comment se créent ces inégalités ? Comment infléchir cette tendance et faire la ville plus juste ?¦Apporter des réponses à cette problématique nécessite d'identifier les facteurs de causalités qui entrent en jeu dans le système de (re)production des inégalités urbaines. Le fonctionnement des marchés foncier et immobilier, la « tyrannie des petites décisions » et les politiques publiques à incidence spatiale sont principalement impliqués. Ces dernières, agissant sur tous les éléments du système, sont placées au coeur de ce travail. On va ainsi s'intéresser précisément à la manière dont les collectivités publiques pilotent la production de la ville contemporaine, en portant l'attention sur la maîtrise publique d'ouvrage (MPO) des grands projets urbains.¦Poser la question de la justice dans la fabrique de la ville implique également de questionner les référentiels normatifs de l'action publique : à quelle conception de la justice celle-ci doit- elle obéir? Quatre perspectives (radicale, substantialiste, procédurale et intégrative) sont caractérisées, chacune se traduisant par des principes d'action différenciés. Une méthodologie hybride - empruntant à la sociologie des organisations et à l'analyse des politiques publiques - vient clore le volet théorique, proposant par un détour métaphorique d'appréhender le projet urbain comme une pièce de théâtre dont le déroulement dépend du jeu d'acteurs.¦Cette méthodologie est utilisée dans le volet empirique de la recherche, qui consiste en une analyse de la MPO d'un projet urbain en cours dans la première couronne de l'agglomération lyonnaise : le Carré de Soie. Trois grands objectifs sont poursuivis : descriptif (reconstruire le scénario), analytique (évaluer la nature de la pièce : conte de fée, tragédie ou match d'improvisation ?) et prescriptif (tirer la morale de l'histoire). La description de la MPO montre le déploiement successif de quatre stratégies de pilotage, dont les implications sur les temporalités, le contenu du projet (programmes, morphologies) et les financements publics vont être déterminantes. Sur la base de l'analyse, plusieurs recommandations peuvent être formulées - importance de l'anticipation et de l'articulation entre planification et stratégie foncière notamment - pour permettre à la sphère publique de dominer le jeu et d'assurer la production de justice par le projet urbain (réalisation puis entretien des équipements et espaces publics, financement de logements de qualité à destination d'un large éventail de populations, etc.). Plus généralement, un décalage problématique peut être souligné entre les territoires stratégiques pour le développement de l'agglomération et les capacités de portage limitées des communes concernées. Ce déficit plaide pour le renforcement des capacités d'investissement de la structure intercommunale.¦La seule logique du marché (foncier, immobilier) mène à la polarisation sociale et à la production d'inégalités urbaines. Faire la ville juste nécessite une forte volonté des collectivités publiques, laquelle doit se traduire aussi bien dans l'ambition affichée - une juste hiérarchisation des priorités dans le développement urbain - que dans son opérationnalisation - une juste maîtrise publique d'ouvrage des projets urbains.¦Inner-city neighborhoods, poor outskirts, and peri-urban spaces with no amenities usually suffer from social and environmental inequalities, such as poverty, unemployment, and exposure to noise and industrial hazards. The observed persistence of these inequalities over time points to an underlying trend - namely, that access to proper living conditions is fundamentally unequal, thus eliciting the question of how such inequalities are effected and how this trend can be reversed so as to build a more equitable city.¦Providing answers to such questions requires that the causal factors at play within the system of (re)production of urban inequalities be identified. Real estate markets, "micromotives and macrobehavior", and public policies that bear on space are mostly involved. The latter are central in that they act on all the elements of the system. This thesis therefore focuses on the way public authorities shape the production of contemporary cities, by studying the public project ownership of major urban projects.¦The study of justice within the urban fabric also implies that the normative frames of reference of public action be questioned: what conception of justice should public action refer to? This thesis examines four perspectives (radical, substantialist, procedural, and integrative) each of which results in different principles of action. This theoretical part is concluded by a hybrid methodology that draws from sociology of organizations and public policy analysis and that suggests that the urban project may be understood as a play, whose outcome hinges on the actors' acting.¦This methodology is applied to the empirical analysis of the public project ownership of an ongoing urban project in the Lyon first-ring suburbs: the Carré de Soie. Three main objectives are pursued: descriptive (reconstructing the scenario), analytical (assessing the nature of the play - fairy tale, tragedy or improvisation match), and prescriptive (drawing the moral of the story). The description of the public project ownership shows the successive deployment of four control strategies, whose implications on deadlines, project content (programs, morphologies), and public funding are significant. Building on the analysis, several recommendations can be made to allow the public sphere to control the process and ensure the urban project produces equity (most notably, anticipation and articulation of planning and real- estate strategy, as well as provision and maintenance of equipment and public spaces, funding of quality housing for a wide range of populations, etc.). More generally, a gap can be highlighted between those territories that are strategic to the development of the agglomeration and the limited resources of the municipalities involved. This deficit calls for strengthening the investment abilities of the intermunicipal structure.¦By itself, the real-estate market logic brings about social polarization and urban inequalities. Building an equitable city requires a strong will on the part of public authorities, a will that must be reflected both in the stated ambition - setting priorities of urban development equitably - and in its implementation managing urban public projects fairly.

Visualization Resources for Iowa State University and the Iowa DOT: An Automated Design Model to Simulator Converter, November 2012

This project developed an automatic conversion software tool that takes input a from an Iowa Department of Transportation (DOT) MicroStation three-dimensional (3D) design file and converts it into a form that can be used by the University of Iowa’s National Advanced Driving Simulator (NADS) MiniSim. Once imported into the simulator, the new roadway has the identical geometric design features as in the Iowa DOT design file. The base roadway appears as a wireframe in the simulator software. Through additional software tools, textures and shading can be applied to the roadway surface and surrounding terrain to produce the visual appearance of an actual road. This tool enables Iowa DOT engineers to work with the universities to create drivable versions of prospective roadway designs. By driving the designs in the simulator, problems can be identified early in the design process. The simulated drives can also be used for public outreach and human factors driving research.