Small scale, grain size and substrate effects in nano-indentation experiment of film-substrate systems

The mechanical properties of film-substrate systems have been investigated through nano-indentation experiments in our former paper (Chen, S.H., Liu, L., Wang, T.C., 2005. Investigation of the mechanical properties of thin films by nano-indentation, considering the effects of thickness and different coating-substrate combinations. Surf. Coat. Technol., 191, 25-32), in which Al-Glass with three different film thicknesses are adopted and it is found that the relation between the hardness H and normalized indentation depth h/t, where t denotes the film thickness, exhibits three different regimes: (i) the hardness decreases obviously with increasing indentation depth; (ii) then, the hardness keeps an almost constant value in the range of 0.1-0.7 of the normalized indentation depth h/t; (iii) after that, the hardness increases with increasing indentation depth. In this paper, the indentation image is further investigated and finite element method is used to analyze the nano-indentation phenomena with both classical plasticity and strain gradient plasticity theories. Not only the case with an ideal sharp indenter tip but also that with a round one is considered in both theories. Finally, we find that the classical plasticity theory can not predict the experimental results, even considering the indenter tip curvature. However, the strain gradient plasticity theory can describe the experimental data very well not only at a shallow indentation depth but also at a deep depth. Strain gradient and substrate effects are proved to coexist in film-substrate nano-indentation experiments. (c) 2006 Elsevier Ltd. All rights reserved.

Theoretical and experimental studies of the bell-jar-top inductively coupled plasma

The present paper describes a systematic study of argon plasmas in a bell-jar inductively coupled plasma (ICP) source over the range of pressure 5-20 mtorr and power input 0.2-0.5 kW, Experimental measurements as well as results of numerical simulations are presented. The models used in the study include the well-known global balance model (or the global model) as well as a detailed two-dimensional (2-D) fluid model of the system, The global model is able to provide reasonably accurate values for the global electron temperature and plasma density, The 2-D model provides spatial distributions of various plasma parameters that make it possible to compare with data measured in the experiments, The experimental measurements were obtained using a tuned Langmuir double-probe technique to reduce the RF interference and obtain the light versus current (I-V) characteristics of the probe. Time-averaged electron temperature and plasma density were measured for various combinations of pressure and applied RF power, The predictions of the 2-D model were found to be in good qualitative agreement with measured data, It was found that the electron temperature distribution T-e was more or less uniform in the chamber, It was also seen that the electron temperature depends primarily on pressure, but is almost independent of the power input, except in the very low-pressure regime. The plasma density goes up almost linearly with the power input.

Singular behaviour near the tip of a sharp V-notch in a power law hardening material

This paper presents an asymptotic analysis of the near-tip stress and strain fields of a sharp V-notch in a power law hardening material. First, the asymptotic solutions of the HRR type are obtained for the plane stress problem under symmetric loading. It is found that the angular distribution function of the radial stress sigma(r) presents rapid variation with the polar angle if the notch angle beta is smaller than a critical notch angle; otherwise, there is no such phenomena. Secondly, the asymptotic solutions are developed for antisymmetric loading in the cases of plane strain and plane stress. The accurate calculation results and the detailed comparisons are given as well. All results show that the singular exponent s is changeable for various combinations of loading condition and plane problem.

Orthotropy rescaling and implications for fracture in composites

For most practically important plane elasticity problems of orthotropic materials, stresses depend on elastic constants through two nondimensional combinations. A spatial rescaling has been found to reduce the orthotropic problems to equivalent problems in materials with cubic symmetry. The latter, under favorable conditions, may be approximated by isotropic materials. Consequently, solutions for orthotropic materials can be constructed approximately from isotropic material solutions or rigorously from cubic ones. The concept is developed to gain insight into the interplay between anisotropy and finite geometry. The inherent simplicity of the solutions allows a variety of technical problems to be addressed efficiently. Included are stress concentration related cracking, effective contraction of orthotropic material specimens, crack deflection onto easy fracture planes, and surface flaw induced delamination.

A política polissêmica: fazeres, dizeres e silêncio nos programas Fale com o Deputado e Fale com a Ouvidoria da Câmara dos Deputados

Estudo sobre os programas Fale com o Deputado e Fale com a Ouvidoria da Câmara dos Deputados, a fim de se captarem representações, crenças e valores sobre a política. O trabalho assume a perspectiva de uma antropologia da política, desnaturalizando conceitos como democracia, participação e representação política, para captar as concepções dos sujeitos envolvidos no diálogo proposto pela Câmara dos Deputados, por intermédio desses canais de correio eletrônico. Assim, a tese não estuda os programas Fale com o Deputado e Fale com a Ouvidoria, mas nos programas. As mensagens enviadas, juntamente com os documentos produzidos pela Casa Legislativa acerca dos programas, bem como notícias e entrevistas com parlamentares e assessores sobre eles, são suportes de expressão de significados associados ao mundo da política, muitas vezes, concebidos como excludentes. Assim, eles são veículos de expressão, mas também de ação, que expõem combinações, normalmente contrapostas, por uma espécie de ficção construída em torno da noção de modernidade: indivíduo e pessoa, diretos e favores, particular e universal. Os documentos abordados revelam conciliações e embates discursivos que acenam para distintas maneiras de os atores fazerem a política, as quais acabam por revelar entendimentos sobre como se dá a gestão interna à Casa desses programas e questionamentos a respeito dos limites e possibilidades da Internet no fazer político.

Effects of Triclopyr on Variable-Leaf Watermilfoil

The objective of the study described here was to determine the effect on variable-leaf watermilfoil of various combinations of triclopyr concentrations and exposure times using dosage rates that controlled Eurasian watermilfoil under laboratory and field conditions (Netherland and Getsinger 1992, Getsinger et al. 1997, Petty et al. 1998).

Observaciones sobre las especies de truchas criollas.

The genus Percichthys (Serranidae) includes three nominal species in Argentina, trucha, vinciguerrae and altispinis. The authors of this paper examine materials from: 1: the Río Negro river in its inferior course, in front of Viedma; 2: lake Pellegrini, near Neuquén, where the rivers Neuquén and Limay meet and form the Negro; 3: Plottier, near the place just named; 4: Colorado river, in Fortín Uno; 5: Curacó river, a tributary to the Colorado, now cut into separate sections since years ago on account of the lack of water; this river normally would connect the Colorado with the rivers up to the San Juan where the « trucha » lives; 6: Luro or La Salada lagoon, formed by the Colorado river near its mouth; 7: Argentino lake, in the southern Patagonia. These fishes are known as « trucha criolla » or « native trout » although the old Spanish name was « perca », more appropiate. Percichthys altispinis Regan 1905 is a good species ; it has been re-found in the Colorado river, at Fortín Uno. An illustration of it is given, characters of four specimens and a note on its scales. P. trucha C. V. reveeals itself on close examination as a complex species or linnean species (linneon) ; with several combinations of characters, but even more materials are needed to establish if there are geographical races (subspecies). A new examination of the Chilean materials is required (former authors considered them jointly with the Atlantic versant or Argentine materials). Some of the infraspeciíic forms are prognathous, and low finned ; others, the contrary; the head may be normal, or conical and bony; etc. As to P. vinciguerrae its standing as a valid species is doubtfull; perhaps, with P. laevis Jenyns it is a southern form. In the same reduced habitat (lagoon, or isolated course) diversified forms are present; some show parallelism with those of other places ; it is supposed that they show ecological influences according to the year or season of birth or developpment. A thorough study of the scales is given, with epidological characteristics and general conciusions as to the method of measuring and comparing their « reading». There are some marked differences even in the same habitat.

Path Planner for Intelligent Laser Surface Modification

An optimal algorithm of manufacturing path planner for intelligent laser surface modification is presented. Elements included in the optimal objective have been analyzed. A 6-D manufacture trace that satisfies the requirements of special craft and 5-axis laser processing robot system has been generated from the path planner by method of parallel section in which combinations of modification spots size with curvature of processing surfaces and modification craft parameters are considered. Related experiments have been successfully carried out with the computer integrated multifunctional laser manufacturing system.

Characterization of the benthos, marine debris and bottom fish at Gray’s Reef National Marine Sanctuary

Executive Summary: Baseline characterization of resources is an essential part of marine protected area (MPA) management and is critical to inform adaptive management. Gray’s Reef National Marine Sanctuary (GRNMS) currently lacks adequate characterization of several key resources as identified in the 2006 Final Management Plan. The objectives of this characterization were to fulfill this need by characterizing the bottom fish, benthic features, marine debris, and the relationships among them for the different bottom types within the sanctuary: ledges, sparse live bottom, rippled sand, and flat sand. Particular attention was given to characterizing the different ledge types, their fish communities, and the marine debris associated with them given the importance of this bottom type to the sanctuary. The characterization has been divided into four sections. Section 1 provides a brief overview of the project, its relevance to sanctuary needs, methods of site selection, and general field procedures. Section 2 provides the survey methods, results, discussion, and recommendations for monitoring specific to the benthic characterization. Section 3 describes the characterization of marine debris. Section 4 is specific to the characterization of bottom fish. Field surveys were conducted during August 2004, May 2005, and August 2005. A total of 179 surveys were completed over ledge bottom (n=92), sparse live bottom (n=51), flat sand (n=20), and rippled sand (n=16). There were three components to each field survey: fish counting, benthic assessment, and quantification of marine debris. All components occurred within a 25 x 4 m belt transect. Two divers performed the transect at each survey site. One diver was responsible for identification of fish species, size, and abundance using a visual survey. The second diver was responsible for characterization of benthic features using five randomly placed 1 m2 quadrats, measuring ledge height and other benthic structures, and quantifying marine debris within the entire transect. GRNMS is composed of four main bottom types: flat sand, rippled sand, sparsely colonized live bottom, and densely colonized live bottom (ledges). Independent evaluation of the thematic accuracy of the GRNMS benthic map produced by Kendall et al. (2005) revealed high overall accuracy (93%). Most discrepancies between map and diver classification occurred during August 2004 and likely can be attributed to several factors, including actual map or diver errors, and changes in the bottom type due to physical forces. The four bottom types have distinct physical and biological characteristics. Flat and rippled sand bottom types were composed primarily of sand substrate and secondarily shell rubble. Flat sand and rippled sand bottom types were characterized by low percent cover (0-2%) of benthic organisms at all sites. Although the sand bottom types were largely devoid of epifauna, numerous burrows indicate the presence of infaunal organisms. Sparse live bottom and ledges were colonized by macroalgae and numerous invertebrates, including coral, gorgonians, sponges, and “other” benthic species (such as tunicates, anemones, and bryozoans). Ledges and sparse live bottom were similar in terms of diversity (H’) given the level of classification used here. However, percent cover of benthic species, with the exception of gorgonians, was significantly greater on ledge than on sparse live bottom. Percent biotic cover at sparse live bottom ranged from 0.7-26.3%, but was greater than 10% at only 7 out of 51 sites. Colonization on sparse live bottom is likely inhibited by shifting sands, as most sites were covered in a layer of sediment up to several centimeters thick. On ledge bottom type, percent cover ranged from 0.42-100%, with the highest percent cover at ledges in the central and south-central region of GRNMS. Biotic cover on ledges is influenced by local ledge characteristics. Cluster analysis of ledge dimensions (total height, undercut height, undercut width) resulted in three main categories of ledges, which were classified as short, medium, and tall. Median total percent cover was 97.6%, 75.1%, and 17.7% on tall, medium, and short ledges, respectively. Total percent cover and cover of macroalgae, sponges, and other organisms was significantly lower on short ledges compared to medium and tall ledges, but did not vary significantly between medium and tall ledges. Like sparse live bottom, short ledges may be susceptible to burial by sand, however the results indicate that ledge height may only be important to a certain threshold. There are likely other factors not considered here that also influence spatial distribution and community structure (e.g., small scale complexity, ocean currents, differential settlement patterns, and biological interactions). GRNMS is a popular site for recreational fishing and boating, and there has been increased concern about the accumulation of debris in the sanctuary and potential effects on sanctuary resources. Understanding the types, abundance, and distribution of debris is essential to improving debris removal and education efforts. Approximately two-thirds of all observed debris items found during the field surveys were fishing gear, and about half of the fishing related debris was monofilament fishing line. Other fishing related debris included leaders and spear gun parts, and non-gear debris included cans, bottles, and rope. The spatial distribution of debris was concentrated in the center of the sanctuary and was most frequently associated with ledges rather than at other bottom types. Several factors may contribute to this observation. Ledges are often targeted by fishermen due to the association of recreationally important fish species with this bottom type. In addition, ledges are structurally complex and are often densely colonized by biota, providing numerous places for debris to become stuck or entangled. Analysis of observed boat locations indicated that higher boat activity, which is an indication of fishing, occurs in the center of the sanctuary. On ledges, the presence and abundance of debris was significantly related to observed boat density and physiographic features including ledge height, ledge area, and percent cover. While it is likely that most fishing related debris originates from boats inside the sanctuary, preliminary investigation of ocean current data indicate that currents may influence the distribution and local retention of more mobile items. Fish communities at GRNMS are closely linked to benthic habitats. A list of species encountered, probability of occurrence, abundance, and biomass by habitat is provided. Species richness, diversity, composition, abundance, and biomass of fish all showed striking differences depending on bottom type with ledges showing the highest values of nearly all metrics. Species membership was distinctly separated by bottom type as well, although very short, sparsely colonized ledges often had a similar community composition to that of sparse live bottom. Analysis of fish communities at ledges alone indicated that species richness and total abundance of fish were positively related to total percent cover of sessile invertebrates and ledge height. Either ledge attribute was sufficient to result in high abundance or species richness of fish. Fish diversity (H`) was negatively correlated with undercut height due to schools of fish species that utilize ledge undercuts such as Pareques species. Concurrent analysis of ledge types and fish communities indicated that there are five distinct combinations of ledge type and species assemblage. These include, 1) short ledges with little or no undercut that lacked many of the undercut associated species except Urophycis earlii ; 2) tall, heavily colonized, deeply undercut ledges typically with Archosargus probatocephalus, Mycteroperca sp., and Pareques sp.; 3) tall, heavily colonized but less undercut with high occurrence of Lagodon rhomboides and Balistes capriscus; 4) short, heavily colonized ledges typically with Centropristis ocyurus, Halichoeres caudalis, and Stenotomus sp.; and 5) tall, heavily colonized, less undercut typically with Archosargus probatocephalus, Caranx crysos and Seriola sp.. Higher levels of boating activity and presumably fishing pressure did not appear to influence species composition or abundance at the community level although individual species appeared affected. These results indicate that merely knowing the basic characteristics of a ledge such as total height, undercut width, and percent cover of sessile invertebrates would allow good prediction of not only species richness and abundance of fish but also which particular fish species assemblages are likely to occur there. Comparisons with prior studies indicate some major changes in the fish community at GRNMS over the last two decades although the causes of the changes are unknown. Species of interest to recreational fishermen including Centropristis striata, Mycteroperca microlepis, and Mycteroperca phenax were examined in relation to bottom features, areas of assumed high versus low fishing pressure, and spatial dispersion. Both Mycteroperca species were found more frequently when undercut height of ledges was taller. They often were found together in small mixed species groups at ledges in the north central and southwest central regions of the sanctuary. Both had lower mode size and proportion of fish above the fishery size limit in heavily fished areas of the sanctuary (i.e. high boat density) despite the presence of better habitat in that region. Black sea bass, C. striata, occurred at 98% of the ledges surveyed and appeared to be evenly distributed throughout the sanctuary. Abundance was best explained by a positive relationship with percent cover of sessile biota but was also negatively related to presence of either Mycteroperca species. This may be due to predation by the Mycteroperca species or avoidance of sites where they are present by C. striata. Suggestions for monitoring bottom features, marine debris, and bottom fish at GRNMS are provided at the end of each chapter. The present assessment has established quantitative baseline characteristics of many of the key resources and use issues at GRNMS. The methods can be used as a model for future assessments to track the trajectory of GRNMS resources. Belt transects are ideally suited to providing efficient and quantitative assessment of bottom features, debris, and fish at GRNMS. The limited visibility, sensitivity of sessile biota, and linear nature of ledge habitats greatly diminish the utility of other sampling techniques. Ledges should receive the bulk of future characterization effort due to their importance to the sanctuary and high variability in physical structure, benthic composition, and fish assemblages. (PDF contains 107 pages.)

Dealing with Energy-QoE Trade-Offs in Mobile Video

Scalable video coding allows an efficient provision of video services at different quality levels with different energy demands. According to the specific type of service and network scenario, end users and/or operators may decide to choose among different energy versus quality combinations. In order to deal with the resulting trade-off, in this paper we analyze the number of video layers that are worth to be received taking into account the energy constraints. A single-objective optimization is proposed based on dynamically selecting the number of layers, which is able to minimize the energy consumption with the constraint of a minimal quality threshold to be reached. However, this approach cannot reflect the fact that the same increment of energy consumption may result in different increments of visual quality. Thus, a multiobjective optimization is proposed and a utility function is defined in order to weight the energy consumption and the visual quality criteria. Finally, since the optimization solving mechanism is computationally expensive to be implemented in mobile devices, a heuristic algorithm is proposed. This way, significant energy consumption reduction will be achieved while keeping reasonable quality levels.

MIRACLE Project Plan

Social scientists have used agent-based models (ABMs) to explore the interaction and feedbacks among social agents and their environments. The bottom-up structure of ABMs enables simulation and investigation of complex systems and their emergent behaviour with a high level of detail; however the stochastic nature and potential combinations of parameters of such models create large non-linear multidimensional “big data,” which are difficult to analyze using traditional statistical methods. Our proposed project seeks to address this challenge by developing algorithms and web-based analysis and visualization tools that provide automated means of discovering complex relationships among variables. The tools will enable modellers to easily manage, analyze, visualize, and compare their output data, and will provide stakeholders, policy makers and the general public with intuitive web interfaces to explore, interact with and provide feedback on otherwise difficult-to-understand models.

Distribution of catch-per-unit-of-effort and fishing effort for tuna in the Eastern Tropical Pacific Ocean by months of the year 1951-1960

ENGLISH: Comparison of physical and biological environmental factors affecting the aggregation of tunas with the success of fishing by the commercial fleets, requires that catch and effort data be examined in greater detail than has been presented in these publications. Consequently, the United States Bureau of Commercial Fisheries Biological Laboratory, San Diego, to serve the needs of its program of research on causes of variations in tuna abundance, made arrangements with the Tuna Commission to summarize these catch and effort data by month, by one-degree area, by fishing vessel size-class, for the years 1951-1960 for bait boats and 1953-1960 for purse-seiners. The present paper describes the techniques employed in summarizing these data by automatic data processing methods. It also presents the catch and effort information by months, by five-degree areas and certain combinations of five-degree areas for use by fishermen, industry personnel, and research agencies. Because of space limitations and other considerations, the one-degree tabulations are not included but are available at the Tuna Commission and Bureau laboratories. SPANISH: La comparación de los factores ambientales físicos y biológicos que afectan la agrupación del atún, con el éxito obtenido en la pesca por las flotas comerciales, requiere que los datos sobre la captura y el esfuerzo sean examinados con mayor detalle de lo que han sido presentados en estas publicaciones. En consecuencia, el Laboratorio Biológico del Buró de Pesquerías Comerciales de los Estados Unidos, situado en San Diego, a fin de llenar los requisitos de su programa de investigación sobre las causas de las variaciones en la abundancia del atún, hizo arreglos con la Comisión del Atún para sumarizar esos datos sobre la captura y el esfuerzo por meses, por áreas de un grado, por clases de tamaño de las embarcaciones de pesca durante los años 1951-1960 en lo que concierne a los barcos de carnada y durante el período 1953-1960 en lo que respecta a los barcos rederos. El presente trabajo describe la técnica empleada en la sumarización de dichos datos mediante métodos automáticos de manejo de datos. También se da aquí la información sobre la captura y el esfuerzo por meses, por áreas de cinco grados y ciertas combinaciones de áreas de cinco grados para el uso de los pescadores, del personal de la industria y de las oficinas de investigación. Por falta de espacio y otras razones, las tabulaciones de las áreas de un grado no han sido incluídos en este trabajo, pero están a la disposición de quien tenga interés en los laboratorios de la Comisión del Atún y del Buró.

Framework for the Shape Optimization of Aerodynamic Profiles Using Genetic Algorithms

This study developed a framework for the shape optimization of aerodynamics profiles using computational fluid dynamics (CFD) and genetic algorithms. Agenetic algorithm code and a commercial CFD code were integrated to develop a CFD shape optimization tool. The results obtained demonstrated the effectiveness of the developed tool. The shape optimization of airfoils was studied using different strategies to demonstrate the capacity of this tool with different GA parameter combinations.

Cost effectiveness of a combination of instruments for global warming: a quantitative approach for Spain

Climate change is an important environmental problem and one whose economic implications are many and varied. This paper starts with the presumption that mitigation of greenhouse gases is a necessary policy that has to be designed in a cost effective way. It is well known that market instruments are the best option for cost effectiveness. But the discussion regarding which of the various market instruments should be used, how they may interact and what combinations of policies should be implemented is still open and very lively. In this paper we propose a combination of instruments: the marketable emission permits already in place in Europe for major economic sectors and a CO(2) tax for economic sectors not included in the emissions permit scheme. The study uses an applied general equilibrium model for the Spanish economy to compute the results obtained with the new mix of instruments proposed. As the combination of the market for emission permits and the CO(2) tax admits different possibilities that depend on how the mitigation is distributed among the economic sectors, we concentrate on four possibilities: cost-effective, equalitarian, proportional to emissions, and proportional to output distributions. Other alternatives to the CO(2) tax are also analysed (tax on energy, on oil and on electricity). Our findings suggest that careful, well designed policies are needed as any deviation imposes significant additional costs that increase more than proportionally to the level of emissions reduction targeted by the EU.

Design and synthesis of quasi-diastereomeric molecules with unchanging central, regenerating axial and switchable helical chirality via cleavage and formation of Ni(II)–O and Ni(II)–N coordination bonds

9 p.