Changes in the global sulfate burden due to perturbations in global CO2 concentrations

A large ensemble of general circulation model (GCM) integrations coupled to a fully interactive sulfur cycle scheme were run on the climateprediction.net platform to investigate the uncertainty in the climate response to sulfate aerosol and carbon dioxide (CO2) forcing. The sulfate burden within the model (and the atmosphere) depends on the balance between formation processes and deposition (wet and dry). The wet removal processes for sulfate aerosol are much faster than dry removal and so any changes in atmospheric circulation, cloud cover, and precipitation will feed back on the sulfate burden. When CO2 is doubled in the Hadley Centre Slab Ocean Model (HadSM3), global mean precipitation increased by 5%; however, the global mean sulfate burden increased by 10%. Despite the global mean increase in precipitation, there were large areas of the model showing decreases in precipitation (and cloud cover) in the Northern Hemisphere during June–August, which reduced wet deposition and allowed the sulfate burden to increase. Further experiments were also undertaken with and without doubling CO2 while including a future anthropogenic sulfur emissions scenario. Doubling CO2 further enhanced the increases in sulfate burden associated with increased anthropogenic sulfur emissions as observed in the doubled CO2-only experiment. The implications are that the climate response to doubling CO2 can influence the amount of sulfate within the atmosphere and, despite increases in global mean precipitation, may act to increase it.

Goal sketching with activity diagrams

Goal orientation is acknowledged as an important paradigm in requirements engineering. The structure of a goal-responsibility model provides opportunities for appraising the intention of a development. Creating a suitable model under agile constraints (time, incompleteness and catching up after an initial burst of creativity) can be challenging. Here we propose a marriage of UML activity diagrams with goal sketching in order to facilitate the production of goal responsibility models under these constraints.

Goal sketching: towards agile requirements engineering

This paper describes a technique that can be used as part of a simple and practical agile method for requirements engineering. The technique can be used together with Agile Programming to develop software in internet time. We illustrate the technique and introduce lazy refinement, responsibility composition and context sketching. Goal sketching has been used in a number of real-world development projects, one of which is described here.

Dipole modes on open periodic structures — an experimental study

An experimental study is made of the lower pass-band of waveguides built as necklaces of oblate spheroids. Short lengths of guide are tested in open resonators. The dominant mode is found to be a glow-wave dipole type having no low-frequency cut off. High Q factors indicate low attenuations. Perturbation measurements demonstrate this energy to be concentrated in the vicinity of the guide.

Information processing: US Patent 4,409,617

An information processor for rendering input data compatible with standard video recording and/or display equipment, comprizing means for digitizing the input data over periods which are synchronous with the fields of a standard video signal, a store adapted to store the digitized data and release stored digitized data in correspondence wiht the line scan of a standard video monitor, the store having two halves which correspond to the interlaced fields of a standard video signal and being so arranged that one half is filed while the other is emptied, and means for converting the released stored digitized data into video luminance signals. The input signals may be in digital or analogue form. A second stage which reconstitutes the recorded data is also described.

A narrow band pulsed eddy current instrument for materials testing

The principles of operation of an experimental prototype instrument known as J-SCAN are described along with the derivation of formulae for the rapid calculation of normalized impedances; the structure of the instrument; relevant probe design parameters; digital quantization errors; and approaches for the optimization of single frequency operation. An eddy current probe is used As the inductance element of a passive tuned-circuit which is repeatedly excited with short impulses. Each impulse excites an oscillation which is subject to decay dependent upon the values of the tuned-circuit components: resistance, inductance and capacitance. Changing conditions under the probe that affect the resistance and inductance of this circuit will thus be detected through changes in the transient response. These changes in transient response, oscillation frequency and rate of decay, are digitized, and then normalized values for probe resistance and inductance changes are calculated immediately in a micro processor. This approach coupled with a minimum analogue processing and maximum of digital processing has advantages compared with the conventional approaches to eddy current instruments. In particular there are: the absence of an out of balance condition and the flexibility and stability of digital data processing.

Review of theoretical models of electromagnetic NDT and their applications

There is an increasing interest in modelling electromagnetic methods of NDT - particularly eddy currents. A collaboration within the International Institute of Welding led to a survey intended to explain to non mathematicians the present scope of modelling. The present review commences with this survey and then points out some of the developments and some of the outstanding problems in transferring modelling into industry.