Dynamic identification of structures: experimental assessment of modal parameteres through methods in frequency domain, in time-frequency domain and model updating

Among the experimental methods commonly used to define the behaviour of a full scale system, dynamic tests are the most complete and efficient procedures. A dynamic test is an experimental process, which would define a set of characteristic parameters of the dynamic behaviour of the system, such as natural frequencies of the structure, mode shapes and the corresponding modal damping values associated. An assessment of these modal characteristics can be used both to verify the theoretical assumptions of the project, to monitor the performance of the structural system during its operational use. The thesis is structured in the following chapters: The first introductive chapter recalls some basic notions of dynamics of structure, focusing the discussion on the problem of systems with multiply degrees of freedom (MDOF), which can represent a generic real system under study, when it is excited with harmonic force or in free vibration. The second chapter is entirely centred on to the problem of dynamic identification process of a structure, if it is subjected to an experimental test in forced vibrations. It first describes the construction of FRF through classical FFT of the recorded signal. A different method, also in the frequency domain, is subsequently introduced; it allows accurately to compute the FRF using the geometric characteristics of the ellipse that represents the direct input-output comparison. The two methods are compared and then the attention is focused on some advantages of the proposed methodology. The third chapter focuses on the study of real structures when they are subjected to experimental test, where the force is not known, like in an ambient or impact test. In this analysis we decided to use the CWT, which allows a simultaneous investigation in the time and frequency domain of a generic signal x(t). The CWT is first introduced to process free oscillations, with excellent results both in terms of frequencies, dampings and vibration modes. The application in the case of ambient vibrations defines accurate modal parameters of the system, although on the damping some important observations should be made. The fourth chapter is still on the problem of post processing data acquired after a vibration test, but this time through the application of discrete wavelet transform (DWT). In the first part the results obtained by the DWT are compared with those obtained by the application of CWT. Particular attention is given to the use of DWT as a tool for filtering the recorded signal, in fact in case of ambient vibrations the signals are often affected by the presence of a significant level of noise. The fifth chapter focuses on another important aspect of the identification process: the model updating. In this chapter, starting from the modal parameters obtained from some environmental vibration tests, performed by the University of Porto in 2008 and the University of Sheffild on the Humber Bridge in England, a FE model of the bridge is defined, in order to define what type of model is able to capture more accurately the real dynamic behaviour of the bridge. The sixth chapter outlines the necessary conclusions of the presented research. They concern the application of a method in the frequency domain in order to evaluate the modal parameters of a structure and its advantages, the advantages in applying a procedure based on the use of wavelet transforms in the process of identification in tests with unknown input and finally the problem of 3D modeling of systems with many degrees of freedom and with different types of uncertainty.

Semantic coordination through programmable Tuple spaces

Two of the main features of today complex software systems like pervasive computing systems and Internet-based applications are distribution and openness. Distribution revolves around three orthogonal dimensions: (i) distribution of control|systems are characterised by several independent computational entities and devices, each representing an autonomous and proactive locus of control; (ii) spatial distribution|entities and devices are physically distributed and connected in a global (such as the Internet) or local network; and (iii) temporal distribution|interacting system components come and go over time, and are not required to be available for interaction at the same time. Openness deals with the heterogeneity and dynamism of system components: complex computational systems are open to the integration of diverse components, heterogeneous in terms of architecture and technology, and are dynamic since they allow components to be updated, added, or removed while the system is running. The engineering of open and distributed computational systems mandates for the adoption of a software infrastructure whose underlying model and technology could provide the required level of uncoupling among system components. This is the main motivation behind current research trends in the area of coordination middleware to exploit tuple-based coordination models in the engineering of complex software systems, since they intrinsically provide coordinated components with communication uncoupling and further details in the references therein. An additional daunting challenge for tuple-based models comes from knowledge-intensive application scenarios, namely, scenarios where most of the activities are based on knowledge in some form|and where knowledge becomes the prominent means by which systems get coordinated. Handling knowledge in tuple-based systems induces problems in terms of syntax - e.g., two tuples containing the same data may not match due to differences in the tuple structure - and (mostly) of semantics|e.g., two tuples representing the same information may not match based on a dierent syntax adopted. Till now, the problem has been faced by exploiting tuple-based coordination within a middleware for knowledge intensive environments: e.g., experiments with tuple-based coordination within a Semantic Web middleware (surveys analogous approaches). However, they appear to be designed to tackle the design of coordination for specic application contexts like Semantic Web and Semantic Web Services, and they result in a rather involved extension of the tuple space model. The main goal of this thesis was to conceive a more general approach to semantic coordination. In particular, it was developed the model and technology of semantic tuple centres. It is adopted the tuple centre model as main coordination abstraction to manage system interactions. A tuple centre can be seen as a programmable tuple space, i.e. an extension of a Linda tuple space, where the behaviour of the tuple space can be programmed so as to react to interaction events. By encapsulating coordination laws within coordination media, tuple centres promote coordination uncoupling among coordinated components. Then, the tuple centre model was semantically enriched: a main design choice in this work was to try not to completely redesign the existing syntactic tuple space model, but rather provide a smooth extension that { although supporting semantic reasoning { keep the simplicity of tuple and tuple matching as easier as possible. By encapsulating the semantic representation of the domain of discourse within coordination media, semantic tuple centres promote semantic uncoupling among coordinated components. The main contributions of the thesis are: (i) the design of the semantic tuple centre model; (ii) the implementation and evaluation of the model based on an existent coordination infrastructure; (iii) a view of the application scenarios in which semantic tuple centres seem to be suitable as coordination media.

The potential of the 3-UPU translational parallel manipulator and a procedure to select the best architecture

The 3-UPU three degrees of freedom fully parallel manipulator, where U and P are for universal and prismatic pair respectively, is a very well known manipulator that can provide the platform with three degrees of freedom of pure translation, pure rotation or mixed translation and rotation with respect to the base, according to the relative directions of the revolute pair axes (each universal pair comprises two revolute pairs with intersecting and perpendicular axes). In particular, pure translational parallel 3-UPU manipulators (3-UPU TPMs) received great attention. Many studies have been reported in the literature on singularities, workspace, and joint clearance influence on the platform accuracy of this manipulator. However, much work has still to be done to reveal all the features this topology can offer to the designer when different architecture, i.e. different geometry are considered. Therefore, this dissertation will focus on this type of the 3-UPU manipulators. The first part of the dissertation presents six new architectures of the 3-UPU TPMs which offer interesting features to the designer. In the second part, a procedure is presented which is based on some indexes, in order to allows the designer to select the best architecture of the 3-UPU TPMs for a given task. Four indexes are proposed as stiffness, clearance, singularity and size of the manipulator in order to apply the procedure.

COBAMOS: Endnutzerprogrammierung auf Basis nachrichtenbasierter Komponentenvernetzung

Die Aufgabenstellung, welche dieser Dissertation zugrunde liegt, lässt sich kurz als die Untersuchung von komponentenbasierten Konzepten zum Einsatz in der Softwareentwicklung durch Endanwender beschreiben. In den letzten 20 bis 30 Jahren hat sich das technische Umfeld, in dem ein Großteil der Arbeitnehmer seine täglichen Aufgaben verrichtet, grundlegend verändert. Der Computer, früher in Form eines Großrechners ausschließlich die Domäne von Spezialisten, ist nun ein selbstverständlicher Bestandteil der täglichen Arbeit. Der Umgang mit Anwendungsprogrammen, die dem Nutzer erlauben in einem gewissen Rahmen neue, eigene Funktionalität zu definieren, ist in vielen Bereichen so selbstverständlich, dass viele dieser Tätigkeiten nicht bewusst als Programmieren wahrgenommen werden. Da diese Nutzer nicht notwendigerweise in der Entwicklung von Software ausgebildet sind, benötigen sie entsprechende Unterstützung bei diesen Tätigkeiten. Dies macht deutlich, welche praktische Relevanz die Untersuchungen in diesem Bereich haben. Zur Erstellung eines Programmiersystems für Endanwender wird zunächst ein flexibler Anwendungsrahmen entwickelt, welcher sich als Basis zur Erstellung solcher Systeme eignet. In Softwareprojekten sind sich ändernde Anforderungen und daraus resultierende Notwendigkeiten ein wichtiger Aspekt. Dies wird im Entwurf des Frameworks durch Konzepte zur Bereitstellung von wieder verwendbarer Funktionalität durch das Framework und Möglichkeiten zur Anpassung und Erweiterung der vorhandenen Funktionalität berücksichtigt. Hier ist zum einen der Einsatz einer serviceorientierten Architektur innerhalb der Anwendung und zum anderen eine komponentenorientierte Variante des Kommando-Musters zu nennen. Zum anderen wird ein Konzept zur Kapselung von Endnutzerprogrammiermodellen in Komponenten erarbeitet. Dieser Ansatz ermöglicht es, unterschiedliche Modelle als Grundlage der entworfenen Entwicklungsumgebung zu verwenden. Im weiteren Verlauf der Arbeit wird ein Programmiermodell entworfen und unter Verwendung des zuvor genannten Frameworks implementiert. Damit dieses zur Nutzung durch Endanwender geeignet ist, ist eine Anhebung der zur Beschreibung eines Softwaresystems verwendeten Abstraktionsebene notwendig. Dies wird durch die Verwendung von Komponenten und einem nachrichtenbasierten Kompositionsmechanismus erreicht. Die vorgenommene Realisierung ist dabei noch nicht auf konkrete Anwendungsfamilien bezogen, diese Anpassungen erfolgen in einem weiteren Schritt für zwei unterschiedliche Anwendungsbereiche.

CFD modeling of two-phase boiling flows in the slug flow regime with an interface capturing technique

The objective of this thesis was to improve the commercial CFD software Ansys Fluent to obtain a tool able to perform accurate simulations of flow boiling in the slug flow regime. The achievement of a reliable numerical framework allows a better understanding of the bubble and flow dynamics induced by the evaporation and makes possible the prediction of the wall heat transfer trends. In order to save computational time, the flow is modeled with an axisymmetrical formulation. Vapor and liquid phases are treated as incompressible and in laminar flow. By means of a single fluid approach, the flow equations are written as for a single phase flow, but discontinuities at the interface and interfacial effects need to be accounted for and discretized properly. Ansys Fluent provides a Volume Of Fluid technique to advect the interface and to map the discontinuous fluid properties throughout the flow domain. The interfacial effects are dominant in the boiling slug flow and the accuracy of their estimation is fundamental for the reliability of the solver. Self-implemented functions, developed ad-hoc, are introduced within the numerical code to compute the surface tension force and the rates of mass and energy exchange at the interface related to the evaporation. Several validation benchmarks assess the better performances of the improved software. Various adiabatic configurations are simulated in order to test the capability of the numerical framework in modeling actual flows and the comparison with experimental results is very positive. The simulation of a single evaporating bubble underlines the dominant effect on the global heat transfer rate of the local transient heat convection in the liquid after the bubble transit. The simulation of multiple evaporating bubbles flowing in sequence shows that their mutual influence can strongly enhance the heat transfer coefficient, up to twice the single phase flow value.

Enabling a direct path from end-user specifications to executable protocols in a biology laboratory environment

Biomedical analyses are becoming increasingly complex, with respect to both the type of the data to be produced and the procedures to be executed. This trend is expected to continue in the future. The development of information and protocol management systems that can sustain this challenge is therefore becoming an essential enabling factor for all actors in the field. The use of custom-built solutions that require the biology domain expert to acquire or procure software engineering expertise in the development of the laboratory infrastructure is not fully satisfactory because it incurs undesirable mutual knowledge dependencies between the two camps. We propose instead an infrastructure concept that enables the domain experts to express laboratory protocols using proper domain knowledge, free from the incidence and mediation of the software implementation artefacts. In the system that we propose this is made possible by basing the modelling language on an authoritative domain specific ontology and then using modern model-driven architecture technology to transform the user models in software artefacts ready for execution in a multi-agent based execution platform specialized for biomedical laboratories.

Numerical simulation of interdigitated back contact hetero-junction solar cells

The goal of this thesis is the application of an opto-electronic numerical simulation to heterojunction silicon solar cells featuring an all back contact architecture (Interdigitated Back Contact Hetero-Junction IBC-HJ). The studied structure exhibits both metal contacts, emitter and base, at the back surface of the cell with the objective to reduce the optical losses due to the shadowing by front contact of conventional photovoltaic devices. Overall, IBC-HJ are promising low-cost alternatives to monocrystalline wafer-based solar cells featuring front and back contact schemes, in fact, for IBC-HJ the high concentration doping diffusions are replaced by low-temperature deposition processes of thin amorphous silicon layers. Furthermore, another advantage of IBC solar cells with reference to conventional architectures is the possibility to enable a low-cost assembling of photovoltaic modules, being all contacts on the same side. A preliminary extensive literature survey has been helpful to highlight the specific critical aspects of IBC-HJ solar cells as well as the state-of-the-art of their modeling, processing and performance of practical devices. In order to perform the analysis of IBC-HJ devices, a two-dimensional (2-D) numerical simulation flow has been set up. A commercial device simulator based on finite-difference method to solve numerically the whole set of equations governing the electrical transport in semiconductor materials (Sentuarus Device by Synopsys) has been adopted. The first activity carried out during this work has been the definition of a 2-D geometry corresponding to the simulation domain and the specification of the electrical and optical properties of materials. In order to calculate the main figures of merit of the investigated solar cells, the spatially resolved photon absorption rate map has been calculated by means of an optical simulator. Optical simulations have been performed by using two different methods depending upon the geometrical features of the front interface of the solar cell: the transfer matrix method (TMM) and the raytracing (RT). The first method allows to model light prop-agation by plane waves within one-dimensional spatial domains under the assumption of devices exhibiting stacks of parallel layers with planar interfaces. In addition, TMM is suitable for the simulation of thin multi-layer anti reflection coating layers for the reduction of the amount of reflected light at the front interface. Raytracing is required for three-dimensional optical simulations of upright pyramidal textured surfaces which are widely adopted to significantly reduce the reflection at the front surface. The optical generation profiles are interpolated onto the electrical grid adopted by the device simulator which solves the carriers transport equations coupled with Poisson and continuity equations in a self-consistent way. The main figures of merit are calculated by means of a postprocessing of the output data from device simulation. After the validation of the simulation methodology by means of comparison of the simulation result with literature data, the ultimate efficiency of the IBC-HJ architecture has been calculated. By accounting for all optical losses, IBC-HJ solar cells result in a theoretical maximum efficiency above 23.5% (without texturing at front interface) higher than that of both standard homojunction crystalline silicon (Homogeneous Emitter HE) and front contact heterojuction (Heterojunction with Intrinsic Thin layer HIT) solar cells. However it is clear that the criticalities of this structure are mainly due to the defects density and to the poor carriers transport mobility in the amorphous silicon layers. Lastly, the influence of the most critical geometrical and physical parameters on the main figures of merit have been investigated by applying the numerical simulation tool set-up during the first part of the present thesis. Simulations have highlighted that carrier mobility and defects level in amorphous silicon may lead to a potentially significant reduction of the conversion efficiency.

Innovative architecture of on-board and on-ground radio systems for space communication

The radio communication system is one of the most critical system of the overall satellite platform: it often represents the only way of communication, between a spacecraft and the Ground Segment or among a constellation of satellites. This thesis focuses on specific innovative architectures for on-board and on-ground radio systems. In particular, this work is an integral part of a space program started in 2004 at the University of Bologna, Forlì campus, which led to the completion of the microsatellite ALMASat-1, successfully launched on-board the VEGA maiden flight. The success of this program led to the development of a second microsatellite, named ALMASat-EO, a three-axis stabilized microsatellite able to capture images of the Earth surface. Therefore, the first objective of this study was focused on the investigation of an innovative, efficient and low cost architecture for on-board radio communication systems. The TT&C system and the high data rate transmitter for images downlink design and realization are thoroughly described in this work, together with the development of the embedded hardware and the adopted antenna systems. Moreover, considering the increasing interest in the development of constellations of microsatellite, in particular those flying in close formations, a careful analysis has been carried out for the development of innovative communication protocols for inter-satellite links. Furthermore, in order to investigate the system aspects of space communications, a study has been carried out at ESOC having as objective the design, implementation and test of two experimental devices for the enhancement of the ESA GS. Thus, a significant portion of this thesis is dedicated to the description of the results of a method for improving the phase stability of GS radio frequency equipments by means of real-time phase compensation and a new way to perform two antennas arraying tracking using already existing ESA tracking stations facilities.

Multilevel Domain Decomposition Algorithms for Monolithic Fluid-Structure Interaction Problems with Application to Haemodynamics

Finite element techniques for solving the problem of fluid-structure interaction of an elastic solid material in a laminar incompressible viscous flow are described. The mathematical problem consists of the Navier-Stokes equations in the Arbitrary Lagrangian-Eulerian formulation coupled with a non-linear structure model, considering the problem as one continuum. The coupling between the structure and the fluid is enforced inside a monolithic framework which computes simultaneously for the fluid and the structure unknowns within a unique solver. We used the well-known Crouzeix-Raviart finite element pair for discretization in space and the method of lines for discretization in time. A stability result using the Backward-Euler time-stepping scheme for both fluid and solid part and the finite element method for the space discretization has been proved. The resulting linear system has been solved by multilevel domain decomposition techniques. Our strategy is to solve several local subproblems over subdomain patches using the Schur-complement or GMRES smoother within a multigrid iterative solver. For validation and evaluation of the accuracy of the proposed methodology, we present corresponding results for a set of two FSI benchmark configurations which describe the self-induced elastic deformation of a beam attached to a cylinder in a laminar channel flow, allowing stationary as well as periodically oscillating deformations, and for a benchmark proposed by COMSOL multiphysics where a narrow vertical structure attached to the bottom wall of a channel bends under the force due to both viscous drag and pressure. Then, as an example of fluid-structure interaction in biomedical problems, we considered the academic numerical test which consists in simulating the pressure wave propagation through a straight compliant vessel. All the tests show the applicability and the numerical efficiency of our approach to both two-dimensional and three-dimensional problems.

Advanced modelling of time domain electromagnetic data with updated hydrogeological interpretations

Several countries have acquired, over the past decades, large amounts of area covering Airborne Electromagnetic data. Contribution of airborne geophysics has dramatically increased for both groundwater resource mapping and management proving how those systems are appropriate for large-scale and efficient groundwater surveying. We start with processing and inversion of two AEM dataset from two different systems collected over the Spiritwood Valley Aquifer area, Manitoba, Canada respectively, the AeroTEM III (commissioned by the Geological Survey of Canada in 2010) and the “Full waveform VTEM” dataset, collected and tested over the same survey area, during the fall 2011. We demonstrate that in the presence of multiple datasets, either AEM and ground data, due processing, inversion, post-processing, data integration and data calibration is the proper approach capable of providing reliable and consistent resistivity models. Our approach can be of interest to many end users, ranging from Geological Surveys, Universities to Private Companies, which are often proprietary of large geophysical databases to be interpreted for geological and\or hydrogeological purposes. In this study we deeply investigate the role of integration of several complimentary types of geophysical data collected over the same survey area. We show that data integration can improve inversions, reduce ambiguity and deliver high resolution results. We further attempt to use the final, most reliable output resistivity models as a solid basis for building a knowledge-driven 3D geological voxel-based model. A voxel approach allows a quantitative understanding of the hydrogeological setting of the area, and it can be further used to estimate the aquifers volumes (i.e. potential amount of groundwater resources) as well as hydrogeological flow model prediction. In addition, we investigated the impact of an AEM dataset towards hydrogeological mapping and 3D hydrogeological modeling, comparing it to having only a ground based TEM dataset and\or to having only boreholes data.

Biochemical analysis of the phosphatase domain of the human soluble epoxide hydrolase (sEH)

Die lösliche Epoxidhydrolase (sEH) gehört zur Familie der Epoxidhydrolase-Enzyme. Die Rolle der sEH besteht klassischerweise in der Detoxifikation, durch Umwandlung potenziell schädlicher Epoxide in deren unschädliche Diol-Form. Hauptsächlich setzt die sEH endogene, der Arachidonsäure verwandte Signalmoleküle, wie beispielsweise die Epoxyeicosatrienoic acid, zu den entsprechenden Diolen um. Daher könnte die sEH als ein Zielenzym in der Therapie von Bluthochdruck und Entzündungen sowie diverser anderer Erkrankungen eingesetzt werden. rnDie sEH ist ein Homodimer, in dem jede Untereinheit aus zwei Domänen aufgebaut ist. Das katalytische Zentrum der Epoxidhydrolaseaktivität befindet sich in der 35 kD großen C-terminalen Domäne. Dieser Bereich der sEH s wurde bereits im Detail untersucht und nahezu alle katalytischen Eigenschaften des Enzyms sowie deren dazugehörige Funktionen sind in Zusammenhang mit dieser Domäne bekannt. Im Gegensatz dazu ist über die 25 kD große N-terminale Domäne wenig bekannt. Die N-terminale Domäne der sEH wird zur Haloacid Dehalogenase (HAD) Superfamilie von Hydrolasen gezählt, jedoch war die Funktion dieses N-terminal Domäne lange ungeklärt. Wir haben in unserer Arbeitsgruppe zum ersten Mal zeigen können, dass die sEH in Säugern ein bifunktionelles Enzym ist, welches zusätzlich zur allgemein bekannten Enzymaktivität im C-terminalen Bereich eine weitere enzymatische Funktion mit Mg2+-abhängiger Phosphataseaktivität in der N-terminalen Domäne aufweist. Aufgrund der Homologie der N-terminalen Domäne mit anderen Enzymen der HAD Familie wird für die Ausübung der Phosphatasefunktion (Dephosphorylierung) eine Reaktion in zwei Schritten angenommen.rnUm den katalytischen Mechanismus der Dephosphorylierung weiter aufzuklären, wurden biochemische Analysen der humanen sEH Phosphatase durch Generierung von Mutationen im aktiven Zentrum mittels ortsspezifischer Mutagenese durchgeführt. Hiermit sollten die an der katalytischen Aktivität beteiligten Aminosäurereste im aktiven Zentrum identifiziert und deren Rolle bei der Dephosphorylierung spezifiziert werden. rnrnAuf Basis der strukturellen und möglichen funktionellen Ähnlichkeiten der sEH und anderen Mitgliedern der HAD Superfamilie wurden Aminosäuren (konservierte und teilweise konservierte Aminosäuren) im aktiven Zentrum der sEH Phosphatase-Domäne als Kandidaten ausgewählt.rnVon den Phosphatase-Domäne bildenden Aminosäuren wurden acht ausgewählt (Asp9 (D9), Asp11 (D11), Thr123 (T123), Asn124 (N124), Lys160 (K160), Asp184 (D184), Asp185 (D185), Asn189 (N189)), die mittels ortsspezifischer Mutagenese durch nicht funktionelle Aminosäuren ausgetauscht werden sollten. Dazu wurde jede der ausgewählten Aminosäuren durch mindestens zwei alternative Aminosäuren ersetzt: entweder durch Alanin oder durch eine Aminosäure ähnlich der im Wildtyp-Enzym. Insgesamt wurden 18 verschiedene rekombinante Klone generiert, die für eine mutante sEH Phosphatase Domäne kodieren, in dem lediglich eine Aminosäure gegenüber dem Wildtyp-Enzym ersetzt wurde. Die 18 Mutanten sowie das Wildtyp (Sequenz der N-terminalen Domäne ohne Mutation) wurden in einem Expressionsvektor in E.coli kloniert und die Nukleotidsequenz durch Restriktionsverdau sowie Sequenzierung bestätigt. Die so generierte N-terminale Domäne der sEH (25kD Untereinheit) wurde dann mittels Metallaffinitätschromatographie erfolgreich aufgereinigt und auf Phosphataseaktivität gegenüber des allgemeinen Substrats 4-Nitophenylphosphat getestet. Diejenigen Mutanten, die Phosphataseaktivität zeigten, wurden anschließend kinetischen Tests unterzogen. Basiered auf den Ergebnissen dieser Untersuchungen wurden kinetische Parameter mittels vier gut etablierter Methoden berechnet und die Ergebnisse mit der „direct linear blot“ Methode interpretiert. rnDie Ergebnisse zeigten, dass die meisten der 18 generierten Mutanten inaktiv waren oder einen Großteil der Enzymaktivität (Vmax) gegenüber dem Wildtyp verloren (WT: Vmax=77.34 nmol-1 mg-1 min). Dieser Verlust an Enzymaktivität ließ sich nicht durch einen Verlust an struktureller Integrität erklären, da der Wildtyp und die mutanten Proteine in der Chromatographie das gleiche Verhalten zeigten. Alle Aminosäureaustausche Asp9 (D9), Lys160 (K160), Asp184 (D184) und Asn189 (N189) führten zum kompletten Verlust der Phosphataseaktivität, was auf deren katalytische Funktion im N-terminalen Bereich der sEH hindeutet. Bei einem Teil der Aminosäureaustausche die für Asp11 (D11), Thr123 (T123), Asn124 (N124) und Asn185 (D185) durchgeführt wurden, kam es, verglichen mit dem Wildtyp, zu einer starken Reduktion der Phosphataseaktivität, die aber dennoch für die einzelnen Proteinmutanten in unterschiedlichem Ausmaß zu messen war (2 -10% and 40% of the WT enzyme activity). Zudem zeigten die Mutanten dieser Gruppe veränderte kinetische Eigenschaften (Vmax allein oder Vmax und Km). Dabei war die kinetische Analyse des Mutanten Asp11  Asn aufgrund der nur bei dieser Mutanten detektierbaren starken Vmax Reduktion (8.1 nmol-1 mg-1 min) und einer signifikanten Reduktion der Km (Asp11: Km=0.54 mM, WT: Km=1.3 mM), von besonderem Interesse und impliziert eine Rolle von Asp11 (D11) im zweiten Schritt der Hydrolyse des katalytischen Zyklus.rnZusammenfassend zeigen die Ergebnisse, dass alle in dieser Arbeit untersuchten Aminosäuren für die Phosphataseaktivität der sEH nötig sind und das aktive Zentrum der sEH Phosphatase im N-terminalen Bereich des Enzyms bilden. Weiterhin tragen diese Ergebnisse zur Aufklärung der potenziellen Rolle der untersuchten Aminosäuren bei und unterstützen die Hypothese, dass die Dephosphorylierungsreaktion in zwei Schritten abläuft. Somit ist ein kombinierter Reaktionsmechanismus, ähnlich denen anderer Enzyme der HAD Familie, für die Ausübung der Dephosphorylierungsfunktion denkbar. Diese Annahme wird gestützt durch die 3D-Struktur der N-terminalen Domäne, den Ergebnissen dieser Arbeit sowie Resultaten weiterer biochemischer Analysen. Der zweistufige Mechanismus der Dephosphorylierung beinhaltet einen nukleophilen Angriff des Substratphosphors durch das Nukleophil Asp9 (D9) des aktiven Zentrums unter Bildung eines Acylphosphat-Enzym-Zwischenprodukts, gefolgt von der anschließenden Freisetzung des dephosphorylierten Substrats. Im zweiten Schritt erfolgt die Hydrolyse des Enzym-Phosphat-Zwischenprodukts unterstützt durch Asp11 (D11), und die Freisetzung der Phosphatgruppe findet statt. Die anderen untersuchten Aminosäuren sind an der Bindung von Mg 2+ und/oder Substrat beteiligt. rnMit Hilfe dieser Arbeit konnte der katalytischen Mechanismus der sEH Phosphatase weiter aufgeklärt werden und wichtige noch zu untersuchende Fragestellungen, wie die physiologische Rolle der sEH Phosphatase, deren endogene physiologische Substrate und der genaue Funktionsmechanismus als bifunktionelles Enzym (die Kommunikation der zwei katalytischen Einheiten des Enzyms) wurden aufgezeigt und diskutiert.rn

Authoring tools and management information systems: study of a generalizable architecture

The need to effectively manage the documentation covering the entire production process, from the concept phase right through to market realise, constitutes a key issue in the creation of a successful and highly competitive product. For almost forty years the most commonly used strategies to achieve this have followed Product Lifecycle Management (PLM) guidelines. Translated into information management systems at the end of the '90s, this methodology is now widely used by companies operating all over the world in many different sectors. PLM systems and editor programs are the two principal types of software applications used by companies for their process aotomation. Editor programs allow to store in documents the information related to the production chain, while the PLM system stores and shares this information so that it can be used within the company and made it available to partners. Different software tools, which capture and store documents and information automatically in the PLM system, have been developed in recent years. One of them is the ''DirectPLM'' application, which has been developed by the Italian company ''Focus PLM''. It is designed to ensure interoperability between many editors and the Aras Innovator PLM system. In this dissertation we present ''DirectPLM2'', a new version of the previous software application DirectPLM. It has been designed and developed as prototype during the internship by Focus PLM. Its new implementation separates the abstract logic of business from the real commands implementation, previously strongly dependent on Aras Innovator. Thanks to its new design, Focus PLM can easily develop different versions of DirectPLM2, each one devised for a specific PLM system. In fact, the company can focus the development effort only on a specific set of software components which provides specialized functions interacting with that particular PLM system. This allows shorter Time-To-Market and gives the company a significant competitive advantage.

New markov chain based methods for single and cross-domain sentiment classification

Nowadays communication is switching from a centralized scenario, where communication media like newspapers, radio, TV programs produce information and people are just consumers, to a completely different decentralized scenario, where everyone is potentially an information producer through the use of social networks, blogs, forums that allow a real-time worldwide information exchange. These new instruments, as a result of their widespread diffusion, have started playing an important socio-economic role. They are the most used communication media and, as a consequence, they constitute the main source of information enterprises, political parties and other organizations can rely on. Analyzing data stored in servers all over the world is feasible by means of Text Mining techniques like Sentiment Analysis, which aims to extract opinions from huge amount of unstructured texts. This could lead to determine, for instance, the user satisfaction degree about products, services, politicians and so on. In this context, this dissertation presents new Document Sentiment Classification methods based on the mathematical theory of Markov Chains. All these approaches bank on a Markov Chain based model, which is language independent and whose killing features are simplicity and generality, which make it interesting with respect to previous sophisticated techniques. Every discussed technique has been tested in both Single-Domain and Cross-Domain Sentiment Classification areas, comparing performance with those of other two previous works. The performed analysis shows that some of the examined algorithms produce results comparable with the best methods in literature, with reference to both single-domain and cross-domain tasks, in $2$-classes (i.e. positive and negative) Document Sentiment Classification. However, there is still room for improvement, because this work also shows the way to walk in order to enhance performance, that is, a good novel feature selection process would be enough to outperform the state of the art. Furthermore, since some of the proposed approaches show promising results in $2$-classes Single-Domain Sentiment Classification, another future work will regard validating these results also in tasks with more than $2$ classes.

Surface-acoustic-wave counterflow micropumps for on-chip liquid motion control in two-dimensional microchannel arrays

Fully controlled liquid injection and flow in hydrophobic polydimethylsiloxane (PDMS) two-dimensional microchannel arrays based on on-chip integrated, low-voltage-driven micropumps are demonstrated. Our architecture exploits the surface-acoustic-wave (SAW) induced counterflow mechanism and the effect of nebulization anisotropies at crossing areas owing to lateral propagating SAWs. We show that by selectively exciting single or multiple SAWs, fluids can be drawn from their reservoirs and moved towards selected positions of a microchannel grid. Splitting of the main liquid flow is also demonstrated by exploiting multiple SAW beams. As a demonstrator, we show simultaneous filling of two orthogonal microchannels. The present results show that SAW micropumps are good candidates for truly integrated on-chip fluidic networks allowing liquid control in arbitrarily shaped two-dimensional microchannel arrays.

Femur Specific Polyaffine Model to Regularize the Log-Domain Demons Registration

Osteoarticular allograft transplantation is a popular treatment method in wide surgical resections with large defects. For this reason hospitals are building bone data banks. Performing the optimal allograft selection on bone banks is crucial to the surgical outcome and patient recovery. However, current approaches are very time consuming hindering an efficient selection. We present an automatic method based on registration of femur bones to overcome this limitation. We introduce a new regularization term for the log-domain demons algorithm. This term replaces the standard Gaussian smoothing with a femur specific polyaffine model. The polyaffine femur model is constructed with two affine (femoral head and condyles) and one rigid (shaft) transformation. Our main contribution in this paper is to show that the demons algorithm can be improved in specific cases with an appropriate model. We are not trying to find the most optimal polyaffine model of the femur, but the simplest model with a minimal number of parameters. There is no need to optimize for different number of regions, boundaries and choice of weights, since this fine tuning will be done automatically by a final demons relaxation step with Gaussian smoothing. The newly developed synthesis approach provides a clear anatomically motivated modeling contribution through the specific three component transformation model, and clearly shows a performance improvement (in terms of anatomical meaningful correspondences) on 146 CT images of femurs compared to a standard multiresolution demons. In addition, this simple model improves the robustness of the demons while preserving its accuracy. The ground truth are manual measurements performed by medical experts.