Aclimatização de mudas micropropagadas de bananeira 'Grand Naine' com aplicação de biofertilizantes em duas estações do ano

A utilização de mudas de bananeira micropropagadas de qualidade é o primeiro passo na implantação de um bom pomar e, para isso, sua aclimatização deve ser realizada de forma adequada. em vista disso, objetivou-se, neste trabalho, avaliar o desempenho dos biofertilizantes HUMITEC® e RUTER AA® no desenvolvimento de mudas de bananeira micropropagadas, sendo instalado um experimento em viveiro comercial de produção de mudas. Foram utilizadas mudas de bananeira cv. Grand Naine, obtidas por micropropagação, sendo, posteriormente, transplantadas em sacos de polietileno preto (1,5 L), contendo, como substrato, terra de subsolo (Latossolo Amarelo), casca de arroz carbonizada e composto orgânico Organifol® (1:1:1). O delineamento experimental foi em blocos ao acaso, fatorial 2 x 4 (produtos e doses), com quatro repetições e quatro plantas úteis por parcela. Os tratamentos foram compostos pelos seguintes biofertilizantes e doses: HUMITEC® (0,0; 4,0; 8,0; 16,0 mL planta-1) e RUTER AA® (0,0; 2,0; 4,0; 8,0 mL planta-1). As doses dos produtos foram divididas em duas aplicações (28 e 56 dias após o transplantio das mudas), aplicadas via fertirrigação. Noventa e oito dias após o transplantio avaliaram-se as seguintes variáveis: altura das plantas (cm), diâmetro do colo rente superfície do solo (mm), área foliar total e por folha, biomassas fresca e seca da parte aérea e das raízes (g). Os dados foram submetidos análise da variância e quando o teste F foi significativo, realizou-se análise de regressão. Pode-se concluir que aplicações de HUMITEC® e RUTER AA® favoreceram o desenvolvimento das mudas e que, no verão, as plantas apresentaram maior desenvolvimento durante a aclimatização.

Relação entre tricomas foliares de genótipos de feijoeiro comum, Phaseolus vulgaris L. e resistência a Diabrotica speciosa Germar, 1824 (Coleoptera: Chrysomelidae)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Influência da relação superfície/volume e do tempo de fritura sobre as alterações da mistura azeite de dendê-óleo de soja

Objetivou-se com este estudo determinar a influência dos fatores relação superfície/volume (S/V) e tempo de fritura sobre a alteração da mistura azeite de dendê-óleo de soja em frituras descontínuas de batatas chips.Foram realizados dois procedimentos de fritura com relações S/V de 0,5 e 1,0 cm-1 e temperatura média de 180°C. O óleo foi aquecido por um período de 7,25 horas. As amostras obtidas durante o processo de fritura foram analisadas pelas determinações de índice de peróxidos, compostos polares totais, ácidos graxos livres e índice de refração. Todas as determinações analíticas foram influenciadas pelo tempo de fritura, verificando-se aumentos significativos destes parâmetros ao longo do processo de fritura. O fator relação S/V apresentou influência sobre os valores dos índices de peróxidos e de refração. A mistura azeite de dendê-óleo de soja apresentou alteração acima do limite recomendado para óleos de fritura (compostos polares totais > 25%) a partir de 6,25 horas de fritura.

Ponto de sela e níveis ótimos de nutrientes em experimentos de adubação

Quando a superfície de resposta tem um ponto de sela ao invés de um ponto de máximo, é de grande importância, do ponto de vista prático, obter soluções alternativas para os níveis ótimos, i.e., a combinação de doses de nutrientes que dá a produção máxima. Três soluções alternativas foram estudadas por simulação: o ponto de máximo absoluto (ponto de máximo fronteira) na região experimental, o ponto de máximo experimental e o ponto de sela. Com exceção do ponto de sela, as soluções apresentaram boas propriedades como substitutas dos níveis ótimos. Utilizando o critério da frequência de máximos, também foi feita uma comparação entre nove delineamentos de tratamentos com três fatores e 3, 5, 7 e 9 níveis. O melhor delineamento de tratamentos foi o fatorial 33 com níveis igualmente espaçados.

Enraizamento de estacas de café cv. mundo novo submetidas a tratamentos auxínicos e com boro

The present research had aimed at studying the auxins and or boron effect on rooting of coffee (Coffea arabica L. cv. Mundo Novo') cuttings. The cuttings were obtained from semi-hardwood orthotropous branches of coffee-tree, containing 2 nodes and with aproximately 10 cm in length. The bases were dipped in treatment solutions composed of IBA or NAA with and without boron during 24 hours. After the treatments, the cuttings were planted in vermiculite. The following could be observed on cuttings taken ninety days after planting - total number of roots formed, average number of roots per cutting and root length. From the results obtained, it can be concluded that cutting treatment with NAA 100 ppm plus boron is responsible for the better rooting of coffee cuttings.

Mancha-foliar-de-Phyllosticta em gengibre. caracterização cultural do patógeno e efeito de tratamentos químicos no controle da doença em Morretes, Estado do Paraná

The objectives of this work were to determine the micelial growth curve of the pathogen and the sensitivity to some fungicides potencially efficient to disease control. The optimum temperature range for micelial growth of Phyllosticta sp, was between 25 and 27.5 degrees C. The maximum and minimum temperatures for micelial growth were 32.5 degrees C and 10 degrees C. Temperatures of 5 and 35 degrees C completely inhibited the growth of the isolates. Total inhibition of the micelial growth was observed with captan and mancozeb (1000 mg a.i./ml) and triadimenol (100 mg a.i./ml). Partial reduction of the micelial growth was observed with iprodione, methyl tiofanate and chlorothalonil until 1.000 mg/ml. The chemical control of PLS was studied in a commercial area of ginger ''Gigante'', in Morretes, PR, where 18 sprays were carried out, with a break of 7 to 10 days, from December to April. The highest reduction of the area under the disease progress curve standardized (AUDPCs) was observed with the spray of chlorothalonil. With the application of dithianon, cupper oxychloride, folpet, mancozeb and captan it was observed AUDPCs between 15.05 and 18.61 lesions/leaf. Iprodione, benomyl, triadimenol and methyl tiofanate did not control the disease (AUDPCs between 20.03 and 25.04 lesions/leaf). The AUDPCs in the check plot was 35.88 lesions/leaf. There was no significant difference of vigor and of ginger yield between fungicide treatments. The cupper oxichloride was phytotoxic to ginger.

A metodologia de superfície de resposta como ferramenta para a avaliação da produção de alginato e poli-hidroxibutirato pela Azotobacter vinelandii

The response surface methodology as a tool for assessing the production of alginate and polyhydroxybutirate by Azotobacter vinelandii. Alginate is a polysaccharide extracted from cell walls of brown algae and used in the food, pharmaceuticals and biotech industries. Production is concentrated on the cultivation of brown seaweed, but several bacteria of the genus Pseudomonas and Azotobacter produce alginate. The chemical structure of alginates produced by algae is similar to those synthesized by A. vinelandii. The bacteria also produce intracellular polymers such as polyhydroxybutyrate (PHB), known as bioplastic. This work studied the simultaneous alginate and PHB production by A. vinelandii using sucrose and different parameters of fermentation in an orbital shaker. The optimal values for the production of these compounds were determined by the MSR. The first experiment was a 2(6-2) factorial design. The second was based on significant variables of the first, resulting in a full 3(3-0) factorial design. From the first to the second, an increase was observed in the PHB productivity from 12 to 45 mg g(-1) cell h(-1) and alginate from 100 to 1,600 mg g(-1) of cell h(-1). The productivity of both compounds was in the maximum incubation temperature of 62 degrees C, in the shortest time of incubation (18h) and the sucrose concentration, 11 g L(-1). In both experiments the PHB extracted presented purity of 94%.

Um estudo sobre a corrosão aquosa de ligas de alumínio 7xxx submetidas a diferentes tratamentos térmicos

This job aim has been to study the aqueous corrosion of the 7xxx heattreatable aluminium alloys, used in the aeronautical industry. The 7010, 7050 and 7475 alloys, have been supplied in the T7 condition and submitted to the annealed and aging thermal treatments of in order to study their behaviours front to corrosion in 5% NaCl pH 6,0, air-saturated and deaerated solutions. The electrochemical study has been accomplished through potential measures in open circuit, potentiodynamic polarisation curves and electrochemical impedance spectroscopy (EIS). The aged alloy resulted to be the most resistant to corrosion and annealed the less resistant ones. In spite of it they have different chemical compositions, in each mean, the alloy with the same thermal treatment has behaved in a similar way. In aerated solution, the process is controlled by oxygen diffusion and in oxygen absence for dissolution through a film. Hardness and mass loss measures, after corrosion test, have supported this research.

Adesão de protozoários ̀a superfície de dispositivos intra-uterinos

Intrauterine devices (IUD) have been used by approximately hundred million of women in the world. IUD are unprescribed to women who have pelvic inflammation disease predisposition which is caused in general by non-treated sexually transmitted diseases (STD). Trichomoniasis, one of the most important vaginal infections, is caused by a flagellated protozoan, Trichomonas vaginalis, transmitted by sexual contact and also asyntomatic women are able to transmit it. The objective of this work was verify by scanning microscopy the adhesion of this protozoan on plastic and metalic IUD surfaces. IUD fragments were added in Diamond medium containing T. vaginalis and after 3 days at 37°C incubation, they were taken out and treated as necessary for scanning microscopy. The analysis showed showed the adhesion of the protozoans on plastic and metalic IUD surfaces. Even though the IUD were not yet directly associated with high incidence of the inflammation pelvic disease, it would become an infection reservoir of potencial pathogenic organisms.

Morfologia da micrópila e da superfície dos ovócitos de piracanjuba, Brycon orbignyanus (Osteichthyes, Characidae), sob microscopia eletrônica de varredura

This paper studied the morphology of oocytes of Brycon orbignyanus, (Osteichthyes, Characidae), through observation in Scanning Electron Microscopy (SEM). Fragments of the ovaries from adult females were collected. During the reproductive period, a hormonal induction in females was carried out to collect the oocytes after extrusion. The samples were fixed and processed for observation in SEM. Results showed that the oocytes of B. orbignyanus had a follicular epithelium formed by a single layer of cells with compressed shape, covering the whole radiatta zone that showed a smooth and regular surface with innumerable pores. The micropyle had a funnel-shaped, containing several furrows. The oocyte surface around the micropyle presented pores closer of each other than the other surface areas of radiatta zone.

Avaliação da formação do biofilme de Candida albicans sobre superfície de titânio revestida com hidroxiapatita por meio de microscopia eletrônica de varredura

In this study Candida albicans biofilm formation on the surface of commercially pure titanium (cp-Ti) coated with hydroxyapatite was observed by means of scanning electron microscope. The biofilm was formed after 45 days of incubation of the samples in liquid culture medium inoculated with fungus cells in a tube of polystyrene with screw cap and sterilized. After the biofilm removal with 10% EDTA solution was observed pitting on the surface of cp-Ti coated.

Geração de modelos digitais de superfície por meio de plataformas computacionais com estrutura vetorial e raster

Geographic Information Systems (GIS) integrate the technologies related to Geoprocessing, with the ability to manipulate georeferenced information through data storage, management and analysis. One of the GIS applications is the generation of Digital Elevation Models (DEM) as a result of rebuilding the elevation of a region using computation tools and artificial representation. This paper presents the DEM created from a point base in two computational frameworks with different structures (vector and raster), comparing the contour lines generated from these models with the original contour lines from analog cartographic base. It was observed that one of the generated models presented some discrepancies related to real space for both GIS structures. However, using constrained Delaunay's triangulation in raster GIS a digital elevation model was generated with contour lines quite close to the original ones, with satisfactory results. A 3-D terrain representation was also created offering a very useful tool for analysis.

Modelagem numérica da superfície na geração da planialtimetra segundo dados de quatro equipamentos topogríficos

The aim of this present work was to compare planialtimetric charts obtained from different risings using two different theodolite types, a total station, and a precision level, used as control. Using a total station, an area was marked with clear variations of relief, following a grid, with a distance of 20 meters among stakes. After that, the stakes were read by the total station and two theodolites of different precisions. The geometric leveling was done by a precision level. The data were input in the DataGeosis software and the numerical modelling of the land was made with mesh of maximum rigidity, generating planialtimetric representation for each rising. It was verified, through comparison of the four representations that little variations occur in relation to the control. The closest representation of the control was the planialtimetry based on the data from the total station, in which the representations obtained from the theodolites were identical among themselves. It was concluded that in the process of obtaining detailed planialtimetry of small areas, submitted to the grid, it was not necessary to use composed geometric leveling, reducing work to the exclusive use of a total station or conventional theodolite.

Análise de superfície de tendência aplicada à chuva, medida por radar meteorológico, nas regiões de Assis e Piracicaba, SP

This paper presents the results from lineal trend surface analysis technique application. The purpose was to detect positive and negative anomalies in the rain measure distribution obtained by the meteorological radar Doppler, band S, located in Bauru, during the period of 21 of October/2004 to 29 of April/2005 in the areas of Assis and Piracicaba. Using three Z-R radar relations for rain quantification was chosen the specific equation Z = 32R1,65, as the best one. The results showed that the applied methodology was able to indicate the space distribution of the rain accumulated, identifying and locating the regions where there was rainy excess and rainy lack during each analyzed period. Such results indicate areas with larger pluvial impact and consequently more favorable for environmental damages.

Métodos de avaliação da eficácia dos tratamentos para a dor.

Pain is a subjective condition and, thus, difficult to measure. The best tools to assess pain are the pain evaluation questionnaires, which provide either diagnostic, pain evolution or pain intensity information. To provide information which could help differentiate between nociceptive pain and neuropathic pain is one of the most important functions of these questionnaires. The questionnaires can measure pain intensity, quality of life, or sleep quality. Quality of life and sleep are two really important characteristics to assess the pain impact on patients' life. Pain intensity assessing questionnaires combine physical evaluations with questions, providing information either from the patient sensations or clinical assessment of pain manifestations as well as the underlying biological mechanisms (such as hyperalgesia or allodynia). For example, the Pain Detect questionnaire has two parts: the patient form (intuitive, with pictures and easy understandable) and the physician form. Thus, in this questionnaire, subjective information is provided by the patient and the objective one is provided by the physician. Other pain intensity questionnaires are NPSI, DN4, LANSS or StEP. Quality of life questionnaires are versatile (can be used in different pathologies). These questionnaires include functional self-evaluation questions, and other ones associated to physical and mental health. Two of such quality of life questionnaires are SF-36 and NHP. Sleep evaluation questionnaires include quantitative features such as the number of sleep interruptions, sleep latency or sleep duration as well as qualitative characteristics such as rest sensation, mood and dreams. One of the most used sleep evaluation questionnaires is PSQI, which includes patient questions and bed-partner questions, providing information from two points of view. Copyright 2009 Prous Science, S.A.U. or its licensors. All rights reserved.