Bacterial cellulose-laponite clay nanocomposites

A novel material comprised of bacterial cellulose (BC) and Laponite clay with different inorganic organic ratios (m/m) was prepared by the contact of never-dried membranes of BC with a previous dispersion of clay particles in water. Field emission scanning electron microscopy (FE-SEM) data of composite materials revealed an effective adhesion of clay over the surface of BC membrane; inorganic particles also penetrate into the polymer bulk, with a significant change of the surface topography even at 5% of clay loading. As a consequence, the mechanical properties are deeply affected by the presence of clay, increasing the values of the Young modulus and the tensile strength. However the maximum strain is decreased when the clay content is increased in the composite in comparison to pristine BC. The main weight loss step of the composites is shifted towards higher temperatures compared to BC, indicating that the clay particles slightly protect the polymer from thermal and oxidative decomposition. (C) 2010 Elsevier Ltd. All rights reserved.

Gas-filled, flat plate solar collectors

This work treats the thermal and mechanical performances of gas-filled, flat plate solar collectors in order to achieve a better performance than that of air filled collectors. The gases examined are argon, krypton and xenon which all have lower thermal conductivity than air. The absorber is formed as a tray connected to the glass. The pressure of the gas inside is near to the ambient and since the gas volume will vary as the temperature changes, there are potential risks for fatigue in the material. One heat transfer model and one mechanical model were built. The mechanical model gave stresses and information on the movements. The factors of safety were calculated from the stresses, and the movements were used as input for the heat transfer model where the thermal performance was calculated. It is shown that gas-filled, flat plate solar collectors can be designed to achieve good thermal performance at a competitive cost. The best yield is achieved with a xenon gas filling together with a normal thick absorber, where normal thick means a 0.25 mm copper absorber. However, a great deal of energy is needed to produce the xenon gas, and if this aspect is taken into account, the krypton filling is better. Good thermal performance can also be achieved using less material; a collector with a 0.1 mm thick copper absorber and the third best gas, which is argon, still gives a better operating performance than a common, commercially produced, air filled collector with a 0.25 mm absorber. When manufacturing gas-filled flat plate solar collectors, one way of decreasing the total material costs significantly, is by changing absorber material from copper to aluminium. Best yield per monetary outlay is given by a thin (0.3 mm) alu-minium absorber with an argon filling. A high factor of safety is achieved with thin absorbers, large absorber areas, rectangular constructions with long tubes and short distances between glass and absorber. The latter will also give a thin layer of gas which gives good thermal performance. The only doubtii ful construction is an argon filled collector with a normal thick (> 0.50 mm) aluminium absorber. In general, an assessment of the stresses for the proposed construction together with appropriate tests are recommended before manufacturing, since it is hard to predict the factor of safety; if one part is reinforced, some other parts can experience more stress and the factor of safety actually drops.

Um modelo numerico para analise de estruturas de materiais compostos considerando efeitos viscoelasticos e falhas progressivas

Neste trabalho apresentam-se pocedimentos para análise não linear de estruturas de materiais compostos laminados reforçados por fibras. A formulação é baseada em uma descrição cinemática incremental Lagrangeana Total, que permite o tratamento de deslocamentos arbitrariamente grandes com pequenas deformações, utilizando elementos finitos tridimensionais degenerados deduzidos para a análise de cascas. As estruturas são consideradas como submetidas a cargas mecânicas e a ações de temperatura e de umidade. O material é suposto elástico linear com propriedades dependentes, ou não, dos valores da temperatura e da concentração de umidade, ou viscoelástico linear com uma relação constitutiva em integral hereditária , e com comportamento higrotermo-reologicamente simples. As lâminas são consideradas como sujeitas a falhas, as quais são detectadas através de critérios macroscópicos, baseados em tensões ou em deformações. As equações não lineares de equilíbrio são resolvidas através de procedimentos iterativos e as deformações dependentes do tempo são avaliadas pelo método das variáveis de estado. Diversos exemplos numéricos de estruturas submetidas à flexão, flambagem elástica e viscoelástica e falhas são apresentados.

Caracterização do beneficiamento de carvão por jigagem no Brasil

Em função da importância do processo de jigagem no beneficiamento de carvão no Brasil, onde 95% da produção bruta, ROM, é beneficiada em jigues para a obtenção de carvão energético ou carvão pré-lavado, e da inexistência de um trabalho sistemático de caracterização deste processo, esta dissertação apresenta um estudo detalhado do desempenho de jigues no beneficiamento de carvão nacional, através do levantamento dos critérios de avaliação de performance dependentes e independentes derivados das curvas de partição e análises densimétricas dos diversos produtos. São desenvolvidos "softwares" para o processamento dos diversos dados levantados "in situ", com aplicação nas áreas de cálculo de balanços de massas e metalúrgico, processamento de análises densimétricas, cálculo de coeficientes de partição, modelamento matemático de curvas de partição e cálculo dos critérios de avaliação de performance. Conclue-se que, de um modo geral, o processo de jigagem é mal empregado no Brasil, conduzindo obtenção de produtos de baixa recuperação. Isto ocorre basicamente em função das características peculiares do carvão nacional e do fato que, no Brasil, utiliza-se jigues de fabricação estrangeira, dimensionados para outros tipos de carvões de melhor qualidade. Este trabalho pretende alertar aos profissionais da área e oferece algumas sugestões com o objetivo de melhorar a baixa eficiência do beneficiamento de carvão observada em diversos lavadores.

Da emigração à diáspora galega: positivação de uma identidade

Este trabalho analisa as transformações ocorridas nas últimas décadas em relação à imagem dos emigrantes galegos e seus descendentes. Por razões políticas inerentes à redemocratização espanhola, mas também em decorrência de novas análises conceituais acerca de minorias, identidades e nacionalidades, a imagem estereotipada do galego como emigrante pobre e ignorante foi revista, principalmente por parte do governo espanhol. Houve um reconhecimento positivado da galeguidade. Assim, o grupo desvalorizado, no início do século XX, passou a integrar uma “diáspora”, que representaria a Galícia no mundo global do século XXI. Essa transformação obedece a movimentos nacionais da Espanha, como a implantação da política das autonomias, que reconheceu a Galícia como uma nacionalidade histórica, e a um contexto internacional marcado pela valorização das identidades e pela ampliação e flexibilidade do conceito de diáspora. Essa mudança acontece, também, tendo como base a grande rede de entidades associativas formada pelos galegos nos países para os quais emigraram. O objetivo do trabalho é apreender essa transformação que positiva um grupo antes considerado de segunda grandeza. Para tanto a tese percorre vasta bibliografia sobre a emigração galega e recorre a vários autores que tentam explicar as razões e os resultados dessa emigração. Nosso ponto, contudo, é entender a reversão de expectativas ocorrida recentemente em relação “ao ser galego” buscando explicar de que forma contribuíram para tanto três atores fundamentais: o governo espanhol (e da Galícia), os emigrantes mundo afora em suas rede associativas e as transformações culturais e conceituais recentes acerca de identidades, nacionalismos, diáspora e direitos, entre outros.

Psicologia social e ideologia: a inserção de um novo/velho conceito e suas consequências para a analise dos fenômenos psico-sociais

O presente trabalho teve por objetivo examinar o surgimento do conceito de ideologia e as transformações que vem sofrendo desde então, tendo como objetivo fundamental sugerir áreas de estudo dentro da Psicologia, particularmente da Psicologia Social, onde a aplicação desta categoria de análise poderia lançar uma luz mais esclarecedora e satisfatória sobre uma série de fenômenos de comportamento, áreas estas que até agora persistem em ignorar os fenômenos ideológicos. Ao final do trabalho foram formuladas críticas severas à maneira pela qual a Psicologia Social vem se realizando no Brasil via EUA, quer a nível metodológico, quer particularmente quanto aos fenômenos por ela estudados. Entre nós se patenteia a ausência e aceitação de enfoques interdisciplinares, bem como a dissociação de tais fenômenos do contexto histórico-político onde ocorrem. Sugeriu-se também a criação entre nós de uma nova área de estudos preferencial para a Psicologia Social - Psicologia Social do proletariado - visando estabelecer, num futuro próximo, um referencial teórico capaz de refletir e compreender realmente a dinâmica social desta classe, isento de comprometimentos classistas, reflexo da ideologia dominante à qual tal classe é tradicionalmente submetida.

Perspectivas sobre o teletrabalho no contexto da administração pública brasileira: um anteprojeto

The job market today, undergoes transformations necessary for employees and employers. Coupled with technological progress, a large degree of connectivity and a new profile of workers opened up many opportunities and relevant aspects that have changed the way of working and their relations in several countries, including Brazil. This technological progress has provided contemporary workers to pursue alternative working outside of the workplace, the office and outside your residence without physical boundaries. Also provided the change in culture of both organizations, as employees, without compromising the Brazilian formal contractual character played by CLT or the Unified Contracting Regime. The emergence of this new type of worker needs to be inserted in the labor market respecting their peculiarities, either by private or public companies. Through a historical review of labor relations and their transformations over time, this research makes a brief reflection and analysis about telework in the Brazilian public administration, implementation, acceptance, advantages, disadvantages, difficulties, external and internal reflections, cultural impact, among others, that this "new" way of working brings to Brazilian society and the various levels of government.

New bacterial cellulose nanocomposites prepared by in situ radical polymerization of methacrylate monomers

Bacterial cellulose/polymethacrylate nanocomposites have received attention in numerous areas of study and in a variety of applications. The attractive properties of methacrylate polymers and bacterial cellulose, BC, allow the synthesis of new nanocomposites with distinct characteristics. In this study, BC/poly(glycidylmethacrylate) (BC/PGMA) and BC/poly(ethyleneglycol)methacrylate (BC/PPEGMA) nanocomposites were prepared through in situ free radical polymerization of GMA and PEGMA, respectively. Ammonium persulphate (APS) was used as an initiator and N,N’methylenebisacrilamide (MBA) was used as a crosslinker in BC/PGMA. Chemical composition, morphology, thermal stability, water absorption, mechanic and surface properties were determined through specific characterization techniques. The optimal polymerization was obtained at (1:2) for BC/PGMA, (1:2:0.2) ratio for BC/GMA/MBA and (1:20) for BC/PPEGMA, with 0.5% of initiator at 60 ºC during 6 h. A maximum of 67% and 87% of incorporation percentage was obtained, respectively, for the nanocomposites BC/PGMA/MBA and BC/PPEGMA. BC/PGMA nanocomposites exhibited an increase of roughness and compactation of the three-dimensional structure, an improvement in the thermal and mechanical properties, and a decrease in their swelling ability and crystallinity. On the other hand, BC/PPEGMA showed a decrease of stiffness of three-dimensional structure, improvement in thermal and mechanical properties, an increase in their swelling ability and a decrease the crystallinity. Both BC/polymethacrylate nanocomposites exhibited a basic surface character. The acid treatment showed to be a suitable strategy to modifiy BC/PGMA nanocomposites through epoxide ring-opening reaction mechanism. Nanocomposites became more compact, smooth and with more water retention ability. A decrease in the thermal and mechanical proprieties was observed. The new nanocomposites acquired properties useful to biomedical applications or/and removal of heavy metals due to the presence of functional groups.

Proposta de método para avaliação do desempenho térmico de residências unifamiliares em clima quente e úmido

Nowadays, evaluation methods to measure thermal performance of buildings have been developed in order to improve thermal comfort in buildings and reduce the use of energy with active cooling and heating systems. However, in developed countries, the criteria used in rating systems to asses the thermal and energy performance of buildings have demonstrated some limitations when applied to naturally ventilated building in tropical climates. The present research has as its main objective to propose a method to evaluate the thermal performance of low-rise residential buildings in warm humid climates, through computational simulation. The method was developed in order to conceive a suitable rating system for the athermal performance assessment of such buildings using as criteria the indoor air temperature and a thermal comfort adaptive model. The research made use of the software VisualDOE 4.1 in two simulations runs of a base case modeled for two basic types of occupancies: living room and bedroom. In the first simulation run, sensitive analyses were made to identify the variables with the higher impact over the cases´ thermal performance. Besides that, the results also allowed the formulation of design recommendations to warm humid climates toward an improvement on the thermal performance of residential building in similar situations. The results of the second simulation run was used to identify the named Thermal Performance Spectrum (TPS) of both occupancies types, which reflect the variations on the thermal performance considering the local climate, building typology, chosen construction material and studied occupancies. This analysis generates an index named IDTR Thermal Performance Resultant Index, which was configured as a thermal performance rating system. It correlates the thermal performance with the number of hours that the indoor air temperature was on each of the six thermal comfort bands pre-defined that received weights to measure the discomfort intensity. The use of this rating system showed to be appropriated when used in one of the simulated cases, presenting advantages in relation to other evaluation methods and becoming a tool for the understanding of building thermal behavior

De repente, tudo mudou de lugar: refletindo sobre metamorfose urbana e gentrificação em Mossoró-RN

This study aims at solidifying the theoretical bases to provide, above all, an explanation for this phenomenon which currently happens, with a scenario of social, political, economic and cultural transformations worldwide in medium cities. Nevertheless, because it has different dimensions from its transformation axes, gentrification comes with change, but also with the introduction of a new purpose in the space using and occupation, outlining in this context the identity of places from the formation of centralities with the presence of flows with social and economic dynamicsThe current forms of geographic space appropriation show the directions of the senses and ideological profile which recreates the meanings and uses of content and materials from descriptions of a historical past. However, today there is an economic context in the urban space which refers to a search of strategies for change, i.e., the acquisition of parameter aimed at meeting the demands of the relationship between capital and labor, which ends up overriding some actions for the specification of the transformation methods within the urban space to be explained by new needs and also by the agents from the value adding to their interests and investments. Thus, we assume that the appreciation/gentrification of urban spaces may or may not result from the building of a public space, since the dialogic structure as a place of political interaction externalize conflicts and disagreements in general; it keeps segregating spaces. As new spaces are transformed, the access to them tends to happen with particular restriction, whereas some places like parks, shopping malls, high-rise and horizontal condos are the scene for major professional and family events. In this context, the gentrification process is used to designate interventions in the urban environment, in certain city spaces which are considered central to public and private investments. A historical place is permitted to be presented as a scenario, a stage full of attractions, through the transformation process. Studying gentrification consists of an analysis of the underlying interests in the transformation of these areas, and especially of the assessment of the interest level in the private sector to partner in order to modify the landscape. Gentrification results from the transformation processes of capital, which influences the efforts and investments application in order to establish and achieve optimal economic growth, focusing on a location socio-culturally centered in the urban space. Thus, the urban social structure develops in the light of some questions that relate not only the cities growth but also environmental conditions it provides in cities like Mossoro, State of Rio Grande do Norte, Brazil 2005 a 2011.

O terciário (re) desenhando a periferia: a região administrativa norte de Natal/RN, na última década do século XX, servicializada na Av. Dr. João Medeiros Filho

The tertiary sector has been (re)defining and (re)qualifying, in an impacting way, the urban spaces in the cities, introducing new elements for the discussion of the relationship center/periphery. In Natal, as an inducing economic activity of its development, it conforms to the new needs of the capital, expanding, being materialized through several processes and spatial forms. We aim at analyzing one of those processes, which has taken its Northern Administrative Area to (re)define the design of its urban space, through the actions developed by the agents involved with the spatialization of the tertiary activities, at the same time as it redimensions its role as a periphery of Natal, contributing to the study of the recent and growing transformations of the Brazilian capitals. The studied district corresponds to 39.4% of the municipal area and, until recently, was composed by precarious reproduction spaces, unprovided of relevant economical activities. After the boom of the development of extensive housing complexes by SFH/BNH, the area, gradually stopped being a dependent area, and it imposed itself as an economically participant region, with the increase of the trade and services sectors, as well as a favorable place for the appearance of new activities. Its reflexes are noticeable in the achieved spatial configuration. As the main road to induct changes, Dr. João Medeiros Filho Avenue presents these new tendencies in the production of the intraurban space, concentrating the largest goods and services equipments of the area, through investments of the private and public sectors, which guarantee the capital allocation for the construction of a new centrality

Centros históricos e desenvolvimento urbano: um estudo comparativo entre os programas Monumenta no Brasil e Polis em Portugal

Both the end of the twentieth century and the beginning of the twenty-first century have been characterized as a period of major political, economic, social and cultural transformations. Two of the major consequences of the political-economical crisis of the end of last century are the restructuring of capitalist production, and the consolidation of neoliberalism as a worldwide phenomenon. This new world political-economical scenario has influenced, in a dialectic way, the contemporary urban development. In that sense, "new" spatial processes and new paradigms in both urban management and urban planning have gained shape. In this context of urban transformations, the central areas of western cities, also known as historic centers, are being increasingly (re)valued. Since the Second World War, the historic centers urban areas which have great infrastructure and symbolic relevance had been undergoing a process of evasion of population and activities, undeniably linked to the neglect of government authorities. However, in recent decades, the question of historic centers rehabilitation has acquired a growing interest, academically and in political agendas. The object of this dissertation is to focus on how the government of each Brazil and Portugal has dealt with the issue of historic center rehabilitation through programs of urban rehabilitation

Análise de componentes arquitetônicos para potencialização da ventilação natural com ênfase em captadores de vento

The building envelope is the principal mean of interaction between indoors and environment, with direct influence on thermal and energy performance of the building. By intervening in the envelope, with the proposal of specific architectural elements, it is possible to promote the use of passive strategies of conditioning, such as natural ventilation. The cross ventilation is recommended by the NBR 15220-3 as the bioclimatic main strategy for the hot and humid climate of Natal/RN, offering among other benefits, the thermal comfort of occupants. The analysis tools of natural ventilation, on the other hand, cover a variety of techniques, from the simplified calculation methods to computer fluid dynamics, whose limitations are discussed in several papers, but without detailing the problems encountered. In this sense, the present study aims to evaluate the potential of wind catchers, envelope elements used to increase natural ventilation in the building, through CFD simplified simulation. Moreover, it seeks to quantify the limitations encountered during the analysis. For this, the procedure adopted to evaluate the elements implementation and efficiency was the CFD simulation, abbreviation for Computer Fluid Dynamics, with the software DesignBuilder CFD. It was defined a base case, where wind catchers were added with various settings, to compare them with each other and appreciate the differences in flows and air speeds encountered. Initially there has been done sensitivity tests for familiarization with the software and observe simulation patterns, mapping the settings used and simulation time for each case simulated. The results show the limitations encountered during the simulation process, as well as an overview of the efficiency and potential of wind catchers, with the increase of ventilation with the use of catchers, differences in air flow patterns and significant increase in air speeds indoors, besides changes found due to different element geometries. It is considered that the software used can help designers during preliminary analysis in the early stages of design

Estudo da moagem de alta energia e sinterização de pós compósitos W-Cu

The Tungsten/copper composites are commonly used for electrical and thermal objectives like heat sinks and lectrical conductors, propitiating an excellent thermal and electrical conductivity. These properties are dependents of the composition, crystallite size and production process. The high energy milling of the powder of W-Cu produces an dispersion high and homogenization levels with crystallite size of W very small in the ductile Cu phase. This work discusses the effect of the HEM in preparation of the W-25Cu composite powders. Three techniques of powder preparation were utilized: milling the dry with powder of thick Cu, milling the dry with powder of fine Cu and milling the wet with powder of thick Cu. The form, size and composition of the particles of the powders milled were observed by scanning electron microscopy (SEM). The X-ray diffraction (XRD) was used to analyse the phases, lattice parameters, size and microstrain of the crystallite. The analyse of the crystalline structure of the W-25Cu powders milled made by Rietveld Method suggests the partial solid solubility of the constituent elements of the Cu in lattice of the W. This analyse shows too that the HEM produces the reduction high on the crystallite size and the increase in the lattice strain of both phases, this is more intense in the phase W

Influência da vermiculita expandida na resistência à compressão e reologia de pastas cimentantes de poços de petróleo

Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration