UHF RFID tag antenna for bottle labeling

In this paper we present a possible design for a passive RFID tag antenna on paper substrate to be integrated into bottle labels. Considering the application scenario, we verified and determined the permittivity and dissipation factor of the materials in order to simulate all the possible sources that would influence the antenna performance. The measured results reported a maximum reading range of 1.45 m even though the efficiency obtained with the antenna integrated into the bottle was only of 3%. © 2014 IEEE.

Extracção automática de informação e conhecimento em textos no âmbito B2B

Dissertação de Mestrado em Engenharia Informática

Drilling delamination outcomes on glass and sisal reinforced plastics

Nowadays, fibre reinforced plastics are used in a wide variety of applications. Apart from the most known reinforcement fibres, like glass or carbon, natural fibres can be seen as an economical alternative. However, some mistrust is yet limiting the use of such materials, being one of the main reasons the inconsistency normally found in their mechanical properties. It should be noticed that these materials are more used for their low density than for their high stiffness. In this work, two different types of reinforced plates were compared: glass reinforced epoxy plate and sisal reinforced epoxy plate. For material characterization purposes, tensile and flexural tests were carried out. Main properties of both materials, like elastic modulus, tensile strength or flexural modulus, are presented and compared with reference values. Afterwards, plates were drilled under two different feed rates: low and high, with two diverse tools: twist and brad type drill, while cutting speed was kept constant. Thrust forces during drilling were monitored. Then, delamination area around the hole was assessed by using digital images that were processed using a computational platform previously developed. Finally, drilled plates were mechanically tested for bearing and open-hole resistance. Results were compared and correlated with the measured delamination. Conclusions contribute to the understanding of natural fibres reinforced plastics as a substitute to glass fibres reinforced plastics, helping on cost reductions without compromising reliability, as well as the consequence of delamination on mechanical resistance of this type of composites.

Damage analysis of carbon/epoxy plates after drilling

Drilling of composites plates normally uses traditional techniques but damage risk is high. NDT use is important. Damage in a carbon/epoxy plate is evaluated by enhanced X-rays. Four different drills are used. The images are analysed using Computational Vision techniques. Surface roughness is compared. Results suggest strategies for delamination reduction.

Tool effects on hybrid laminates drilling

Fiber reinforced plastics are increasing their importance as one of the most interesting groups of material on account of their low weight, high strength, and stiffness. To obtain good quality holes, it is important to identify the type of material, ply stacking sequence, and fiber orientation. In this article, the drilling of quasi-isotropic hybrid carbon +glass/epoxy plates is analyzed. Two commercial drills and a special step drill are compared considering the thrust force and delamination extension. Results suggest that the proposed step drill can be a suitable option in laminate drilling.

Drilling tool geometry evaluation for reinforced composite laminates

In this work, a comparative study on different drill point geometries and feed rate for composite laminates drilling is presented. For this goal, thrust force monitoring during drilling, hole wall roughness measurement and delamination extension assessment after drilling is accomplished. Delamination is evaluated using enhanced radiography combined with a dedicated computational platform that integrates algorithms of image processing and analysis. An experimental procedure was planned and consequences were evaluated. Results show that a cautious combination of the factors involved, like drill tip geometry or feed rate, can promote the reduction of delamination damage.

Validity and reliability of a health care service evaluation instrument for tuberculosis

OBJECTIVE To evaluate the validity and reliability of an instrument that evaluates the structure of primary health care units for the treatment of tuberculosis.METHODS This cross-sectional study used simple random sampling and evaluated 1,037 health care professionals from five Brazilian municipalities (Natal, state of Rio Grande do Norte; Cabedelo, state of Paraíba; Foz do Iguaçu, state of Parana; Sao José do Rio Preto, state of Sao Paulo, and Uberaba, state of Minas Gerais) in 2011. Structural indicators were identified and validated, considering different methods of organization of the health care system in the municipalities of different population sizes. Each structure represented the organization of health care services and contained the resources available for the execution of health care services: physical resources (equipment, consumables, and facilities); human resources (number and qualification); and resources for maintenance of the existing infrastructure and technology (deemed as the organization of health care services). The statistical analyses used in the validation process included reliability analysis, exploratory factor analysis, and confirmatory factor analysis.RESULTS The validation process indicated the retention of five factors, with 85.9% of the total variance explained, internal consistency between 0.6460 and 0.7802, and quality of fit of the confirmatory factor analysis of 0.995 using the goodness-of-fit index. The retained factors comprised five structural indicators: professionals involved in the care of tuberculosis patients, training, access to recording instruments, availability of supplies, and coordination of health care services with other levels of care. Availability of supplies had the best performance and the lowest coefficient of variation among the services evaluated. The indicators of assessment of human resources and coordination with other levels of care had satisfactory performance, but the latter showed the highest coefficient of variation. The performance of the indicators “training” and “access to recording instruments” was inferior to that of other indicators.CONCLUSIONS The instrument showed feasibility of application and potential to assess the structure of primary health care units for the treatment of tuberculosis.

Sensores de imagem de grande área em tecnologia de silício amorfo

Dissertação apresentada para a obtenção do grau de Doutor em Ciência e Engenharia dos Materiais, especialidade Microelectrónica e Optoelectrónica pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Estudo da influência da pré-furação no dano em laminados carbono/epóxido

Na furação de placas em materiais compósitos é corrente o uso de técnicas tradicionais de furação adaptadas. O defeito mais grave é a delaminação, que nem sempre é visível à superfície e pode causar o colapso prematuro das estruturas. Para a avaliação dos danos provocados nas peças utilizam-se meios de controlo não-destrutivo. Neste artigo são analisados os resultados obtidos através do recurso à pré-furação em placas carbono/epóxido e de duas técnicas de controlo. Os resultados obtidos permitem estabelecer a influência da pré-furação na delaminação Neste trabalho, utilizam-se técnicas de Visão Computacional no processamento e análise das imagens obtidas nos ensaios experimentais.

Damage assessment of drilled hybrid composite laminates

Hole drilling operations are common in fibre reinforced plastics - FRP’s - to facilitate fastener assembly to other parts in more complex structures. As these materials are non-homogeneous, drilling causes some damages, like delamination, for example. Delamination can be reduced by a careful selection of drilling parameters, drill material and drill bit geometry. In this work two types of laminates are drilled using different machining parameters and comparing drill geometries. Results show the importance of a cautious selection of these variables when composites’ drilling is involved.

Influência dos parâmetros de maquinagem no dano de placas compósitas

Os materiais compósitos têm-se tornado cada vez mais importantes em virtude das suas características específicas, tais como o baixo peso e uma boa relação peso/resistência. As operações de furação são habituais neste tipo de peças, devido à necessidade de posterior montagem em conjuntos. Devido à não-homogeneidade dos compósitos, a furação pode causar alguns danos, de que podem resultar perda de propriedades mecânicas da peça. Uma escolha adequada da ferramenta e dos parâmetros pode diminuir estas consequências. Neste artigo são comparados os resultados obtidos com três diferentes velocidades de corte, três avanços e três geometrias de ferramenta. As conclusões apontam para a importância duma adequada selecção dos parâmetros de maquinagem na redução do dano.

Avaliação de ferramentas para a furação de laminados

“Drlling of polymeric matrix composites structures"

Avaliação da delaminação após furação em compósitos laminados

As características excepcionais dos materiais compósitos de matriz polimérica têm conduzido à sua crescente utilização em todos os domínios. A necessidade de ligar estas peças entre si obriga à realização frequente de operações de furação que, embora devidamente adaptada, pode provocar diferentes tipos de dano nas peças a ligar. Desses, o dano mais grave é a delaminação pelas suas consequências na perda das propriedades mecânicas. Neste trabalho é apresentado um estudo comparativo da extensão do dano em função da geometria de ferramenta utilizada. Para tal as placas foram radiografadas após furação e a imagem resultante segmentada para medição das áreas associadas. Os resultados mostram a importância de uma adequada geometria de ferramenta na redução do dano causado pela furação em compósitos laminados.

Drilling process of composite laminates – a tool based analysis

“Drilling of polymeric matrix composites structures”

Utilização de algoritmos de processamento e análise de imagem na avaliação do dano em placas compósitas

PTDC/EME–TME/66207/2006 e POSC/EEA-SRI/55386/2004