Nonlinear analysis of plastic ball grid array solder joints

A nonlinear finite element analysis was carried out to investigate the viscoplastic deformation of solder joints in a ball grid array (BGA) package under temperature cycle. The effects of constraint on print circuit board (PCB) and stiffness of substrate on the deformation behaviour of the solder joints were also studied. A relative damage stress was adopted to analyze the potential failure sites in the solder joints. The results indicated that high inelastic strain and strain energy density were developed in the joints close to the package center. On the other hand, high constraint and high relative damage stress were associated with the joint closest to the edge of the silicon chip. The joint closest to the edge of the silicon chip was regarded as the most susceptible failure site if cavitation instability is the dominant failure mechanism. Increase the external constraint on the print circuit board (PCB) causes a slight increase in stress triaxiality (m/eq) and relative damage stress in the joint closest to the edge of silicon die. The relative damage stress is not sensitive to the Young’s modulus of the substrate.

Estimating present day extreme water level exceedance probabilities around the coastline of Australia : tides, extra-tropical storm surges and mean sea level

The occurrence of extreme water levels along low-lying, highly populated and/or developed coastlines can lead to considerable loss of life and billions of dollars of damage to coastal infrastructure. Therefore it is vitally important that the exceedance probabilities of extreme water levels are accurately evaluated to inform risk-based flood management, engineering and future land-use planning. This ensures the risk of catastrophic structural failures due to under-design or expensive wastes due to over-design are minimised. This paper estimates for the first time present day extreme water level exceedence probabilities around the whole coastline of Australia. A high-resolution depth averaged hydrodynamic model has been configured for the Australian continental shelf region and has been forced with tidal levels from a global tidal model and meteorological fields from a global reanalysis to generate a 61-year hindcast of water levels. Output from this model has been successfully validated against measurements from 30 tide gauge sites. At each numeric coastal grid point, extreme value distributions have been fitted to the derived time series of annual maxima and the several largest water levels each year to estimate exceedence probabilities. This provides a reliable estimate of water level probabilities around southern Australia; a region mainly impacted by extra-tropical cyclones. However, as the meteorological forcing used only weakly includes the effects of tropical cyclones, extreme water level probabilities are underestimated around the western, northern and north-eastern Australian coastline. In a companion paper we build on the work presented here and more accurately include tropical cyclone-induced surges in the estimation of extreme water level. The multi-decadal hindcast generated here has been used primarily to estimate extreme water level exceedance probabilities but could be used more widely in the future for a variety of other research and practical applications.

Self-determination, control, and reactions to changes in workload : a work simulation

The objective of this experimental study is to capture the dynamic temporal processes that occur in changing work settings and to test how work control and individuals' motivational predispositions interact to predict reactions to these changes. To this aim, we examine the moderating effects of global self-determined and non-self-determined motivation, at different levels of work control, on participants' adaptation and stress reactivity to changes in workload during four trials of an inbox activity. Workload was increased or decreased at Trial 3, and adaptation to this change was examined via fluctuations in anxiety, coping, motivation, and performance. In support of the hypotheses, results revealed that, for non-self-determined individuals, low work control was stress-buffering and high work control was stress-exacerbating when predicting anxiety and intrinsic motivation. In contrast, for self-determined individuals, high work control facilitated the adaptive use of planning coping in response to a change in workload. Overall, this pattern of results demonstrates that, while high work control was anxiety-provoking and demotivating for non-self-determined individuals, self-determined individuals used high work control to implement an adaptive antecedent-focused emotion regulation strategy (i.e., planning coping) to meet situational demands. Other interactive effects of global motivation emerged on anxiety, active coping, and task performance. These results and their practical implications are discussed.

Occupational health psychology

In this chapter, the occupational stress process and implications for the management of occupational health and safety in organisations are discussed. The chapter begins by introducing occupational stress as a process by which stressors (e.g. time pressure) result in strains (e.g. ill health). The consequences of stress, to both the individual and the organisation are discussed, and several key sources of occupational stress are also described. Theories of occupational stress that attempt to explain how stressors lead to strain and also describe different job resources (e.g. autonomy, support, and security) that can alleviate the detrimental effects of occupational stressors are then presented. The management of occupational stress at both the individual and organisational levels is also discussed. In the subsequent section, work-life balance and various ways work impacts on life and vice versa are described. The management of work-life conflict and the effectiveness of initiatives designed to address imbalance between work and life are then discussed. Finally, occupational health and safety is described with a particular focus on primary prevention as well as the legislative frameworks that guide psychosocial risk management in Australian organisations.

The alcohol culture of mature-aged women : similarities and differences across borders

Introduction: Relatively few attempts have been made to describe and understand women’s alcohol consumption beyond adolescence and young adulthood. In particular, there has been a lack of studies focusing on the alcohol culture that surrounds and guides mature-aged women’s drinking. As part of a larger cross-national comparison, the present study sought to address this gap by identifying the shared beliefs and values that impact on drinking outcomes among mature-aged women in Sweden and Australia. Method: The study was guided by an ethnographic methodology. To generate data, a series of semi-structured interview were conducted with 17 Australian (age = 45-57 years; M = 52.1, SD = 3.9) and 19 Swedish (age = 45-58 years; M = 52.2, SD = 4.8) women. All interviews were transcribed verbatim and thematically analysed. Results: With age, the focus of alcohol as a single purpose vehicle for intoxication had given way to a focus on the enjoyment and ritual of drinking itself; taste had become increasingly important and alcohol was strongly associated with pleasurable environments and experiences. The view of alcohol as a taste experience was particularly pronounced among the Swedish women, with alcohol (most commonly wine) often seen as inseparable from food. Among the Swedish women, this view of alcohol was also associated with a strong de-emphasis of the pharmacological effects of alcohol. In contrast, several Australian women understood and used alcohol as relief for anxiety and stress. Moderate drinking was linked to the social construction of both age and gender in the two samples, while heavy or abusive alcohol consumption was associated with strong proscriptive norms and stigma. Conclusions: Australian and Swedish women share a number of beliefs and values around alcohol, however, these findings also show unique country-level differences. Implications for drinking outcomes are discussed.

Discharge parameters and dominant electron conductivity mechanism in a low-pressure planar magnetron discharge

Parameters of a discharge sustained in a planar magnetron configuration with crossed electric and magnetic fields are studied experimentally and numerically. By comparing the data obtained in the experiment with the results of calculations made using the proposed theoretical model, conclusion was made about the leading role of the turbulence-driven Bohm electron conductivity in the low-pressure operation mode (up to 1 Pa) of the discharge in crossed electric and magnetic fields. A strong dependence of the width of the cathode sputter trench, associated with the ionization region of the magnetron discharge, on the discharge parameters was observed in the experiments. The experimental data were used as input parameters in the discharge model that describes the motion of secondary electrons across the magnetic field in the ionization region and takes into account the classical, near-wall, and Bohm mechanisms of electron conductivity.

Development of gas sensing technology for ground and airborne applications powered by solar energy : methodology and experimental results

Monitoring gases for environmental, industrial and agricultural fields is a demanding task that requires long periods of observation, large quantity of sensors, data management, high temporal and spatial resolution, long term stability, recalibration procedures, computational resources, and energy availability. Wireless Sensor Networks (WSNs) and Unmanned Aerial Vehicles (UAVs) are currently representing the best alternative to monitor large, remote, and difficult access areas, as these technologies have the possibility of carrying specialised gas sensing systems, and offer the possibility of geo-located and time stamp samples. However, these technologies are not fully functional for scientific and commercial applications as their development and availability is limited by a number of factors: the cost of sensors required to cover large areas, their stability over long periods, their power consumption, and the weight of the system to be used on small UAVs. Energy availability is a serious challenge when WSN are deployed in remote areas with difficult access to the grid, while small UAVs are limited by the energy in their reservoir tank or batteries. Another important challenge is the management of data produced by the sensor nodes, requiring large amount of resources to be stored, analysed and displayed after long periods of operation. In response to these challenges, this research proposes the following solutions aiming to improve the availability and development of these technologies for gas sensing monitoring: first, the integration of WSNs and UAVs for environmental gas sensing in order to monitor large volumes at ground and aerial levels with a minimum of sensor nodes for an effective 3D monitoring; second, the use of solar energy as a main power source to allow continuous monitoring; and lastly, the creation of a data management platform to store, analyse and share the information with operators and external users. The principal outcomes of this research are the creation of a gas sensing system suitable for monitoring any kind of gas, which has been installed and tested on CH4 and CO2 in a sensor network (WSN) and on a UAV. The use of the same gas sensing system in a WSN and a UAV reduces significantly the complexity and cost of the application as it allows: a) the standardisation of the signal acquisition and data processing, thereby reducing the required computational resources; b) the standardisation of calibration and operational procedures, reducing systematic errors and complexity; c) the reduction of the weight and energy consumption, leading to an improved power management and weight balance in the case of UAVs; d) the simplification of the sensor node architecture, which is easily replicated in all the nodes. I evaluated two different sensor modules by laboratory, bench, and field tests: a non-dispersive infrared module (NDIR) and a metal-oxide resistive nano-sensor module (MOX nano-sensor). The tests revealed advantages and disadvantages of the two modules when used for static nodes at the ground level and mobile nodes on-board a UAV. Commercial NDIR modules for CO2 have been successfully tested and evaluated in the WSN and on board of the UAV. Their advantage is the precision and stability, but their application is limited to a few gases. The advantages of the MOX nano-sensors are the small size, low weight, low power consumption and their sensitivity to a broad range of gases. However, selectivity is still a concern that needs to be addressed with further studies. An electronic board to interface sensors in a large range of resistivity was successfully designed, created and adapted to operate on ground nodes and on-board UAV. The WSN and UAV created were powered with solar energy in order to facilitate outdoor deployment, data collection and continuous monitoring over large and remote volumes. The gas sensing, solar power, transmission and data management systems of the WSN and UAV were fully evaluated by laboratory, bench and field testing. The methodology created to design, developed, integrate and test these systems was extensively described and experimentally validated. The sampling and transmission capabilities of the WSN and UAV were successfully tested in an emulated mission involving the detection and measurement of CO2 concentrations in a field coming from a contaminant source; the data collected during the mission was transmitted in real time to a central node for data analysis and 3D mapping of the target gas. The major outcome of this research is the accomplishment of the first flight mission, never reported before in the literature, of a solar powered UAV equipped with a CO2 sensing system in conjunction with a network of ground sensor nodes for an effective 3D monitoring of the target gas. A data management platform was created using an external internet server, which manages, stores, and shares the data collected in two web pages, showing statistics and static graph images for internal and external users as requested. The system was bench tested with real data produced by the sensor nodes and the architecture of the platform was widely described and illustrated in order to provide guidance and support on how to replicate the system. In conclusion, the overall results of the project provide guidance on how to create a gas sensing system integrating WSNs and UAVs, how to power the system with solar energy and manage the data produced by the sensor nodes. This system can be used in a wide range of outdoor applications, especially in agriculture, bushfires, mining studies, zoology, and botanical studies opening the way to an ubiquitous low cost environmental monitoring, which may help to decrease our carbon footprint and to improve the health of the planet.

Psychological health of medical and dental students in Saudi Arabia : a longitudinal study

Introduction: Many studies have indicated the poor psychological health of medical and dental students. However, few studies have assessed the longitudinal trajectory of that psychological health at different times in an academic year. Aim: To evaluate the positive and negative aspects of psychological health among preclinical medical and dental students in Saudi Arabia prospectively. Methods: A total of 317 preclinical medical and dental students were recruited for a longitudinal study design from second and third-year students at Umm Al-Qura University in the 2012-2013 academic year. The students were assessed at the middle of the first term and followed up after 3-monthes at the beginning of the second term. Questionnaires included assessment of depression, anxiety, stress, self-efficacy, and satisfaction with life. Results: Depression, anxiety, stress, and satisfaction with life were improved significantly at the beginning of the second term, whereas self-efficacy did not change significantly. The medical, female, and third-year student subgroups had the most significant changes. Depression and stress were significantly changed at the beginning of the second term in most demographic subgroups. Conclusion: Preclinical medical and dental students have different psychological health levels at different times of the same academic year. It is recommended to consider time of data collection when analyzing the results of such studies.

Characterization of the tail-specific protease (Tsp) from Legionella

Bacterial tail-specific proteases (Tsps) have been attributed a wide variety of functions including intracellular virulence, cell wall morphology, proteolytic signal cascades and stress response. This study tested the hypothesis that Tsp has a key function for the transmissive form of Legionella pneumophila. A tsp mutant was generated in Legionella pneumophila 130b and the characteristics of this strain and the isogenic wild-type were examined using a range of growth and proteomic analyses. Recombinant Tsp protein was also produced and analyzed. The L. pneumophila tsp mutant showed no defect in growth on rich media or during thermo-osmotic stress conditions. In addition, no defects in cellular morphology were observed when the cells were examined using transmission electron microscopy. Purified recombinant Tsp was found to be an active protease with a narrow substrate range. Proteome analysis using iTRAQ (5% coverage of the proteome) found that, of those proteins detected, only 5 had different levels in the tsp mutant compared to the wild type. ACP (Acyl Carrier Protein), which has a key role for Legionella differentiation to the infectious form, was reduced in the tsp mutant; however, tsp(-) was able to infect and replicate inside macrophages to the same extent as the wild type. Combined, these data demonstrate that Tsp is a protease but is not essential for Legionella growth or cell infection. Thus, Tsp may have functional redundancy in Legionella.

Tendinopathy alters cumulative transverse strain in the patellar tendon postexercise.

Introduction This research evaluated the effect of tendinopathy on the cumulative transverse strain response of the patellar tendon to a bout of resistive quadriceps exercise. Methods Nine adults with unilateral patellar tendinopathy (age 18.2±0.7 years, height 1.92±0.06 m and weight 76.8±6.8 kg) and ten healthy adults free of knee pain (age 17.8±0.8 years, height 1.83±0.05 m and weight 73.2±7.6 kg) underwent standardised sagittal sonograms (7.2–14 MHz linear–array transducer) of both patellar tendons immediately prior and following 45 repetitions of a double–leg decline–squat exercise performed against a resistance of 145% bodyweight. Tendon thickness was determined 5–mm and 25–mm distal to the patellar pole. Transverse Hencky strain was calculated as the natural log of the ratio of post– to pre–exercise tendon thickness and expressed as a percentage. Measures of tendon echogenicity were calculated within the superficial and deep aspects of each tendon site from gray–scale profiles. Intratendinous microvessels were evaluated using power Doppler ultrasound. Results The cumulative transverse strain response to exercise in symptomatic tendinopathy was significantly lower than that of asymptomatic and healthy tendon (P<.05). There was also a significant reduction (57%) in the area of microvascularity immediately following exercise (P=.05), which was positively correlated (r=0.93, P<.05) with VISA-P score. Conclusions This study is the first to show that patellar tendinopathy is associated with an altered morphological and mechanical response of the tendon to exercise, which is manifest by a reduction in cumulative transverse strain and microvascularity, when present. Research directed toward identifying factors that influence the acute microvascular and transverse strain response of the patellar tendon to exercise in the various stages of tendinopathy is warranted.

Modelling and performance of an active heave compensator for offshore operations

The development of offshore oil and gas fields require the placement of different equipment on the sea floor. This is done by deploying the equipment from vessels operating in dynamic positioning on the surface. The deployment operation has different phases, and in higher sea states, it may require wave-load synchronization, when the load is going through the splash zone, and heave compensation when the load is close to the sea floor. In this paper, we analyse the performance of a particular type of hardware operating in a heave compensation mode. We derive a comprehensive model, analyse limits of performance and evaluate a control strategy.

The driving visual field and a history of motor vehicle collision involvement in older drivers: A population-based examination

Purpose We designed a visual field test focused on the field utilized while driving to examine associations between field impairment and motor vehicle collision involvement in 2,000 drivers ≥70 years old. Methods The "driving visual field test" involved measuring light sensitivity for 20 targets in each eye, extending 15° superiorly, 30° inferiorly, 60° temporally and 30° nasally. The target locations were selected on the basis that they fell within the field region utilized when viewing through the windshield of a vehicle or viewing the dashboard while driving. Monocular fields were combined into a binocular field based on the more sensitive point from each eye. Severe impairment in the overall field or a region was defined as average sensitivity in the lowest quartile of sensitivity. At-fault collision involvement for five years prior to enrollment was obtained from state records. Poisson regression was used to calculate crude and adjusted rate ratios examining the association between field impairment and at-fault collision involvement. Results Drivers with severe binocular field impairment in the overall driving visual field had a 40% increased rate of at-fault collision involvement (RR 1.40, 95%CI 1.07-1.83). Impairment in the lower and left fields was associated with elevated collision rates (RR 1.40 95%CI 1.07-1.82 and RR 1.49, 95%CI 1.15-1.92, respectively), whereas impairment in the upper and right field regions was not. Conclusions Results suggest that older drivers with severe impairment in the lower or left region of the driving visual field are more likely to have a history of at-fault collision involvement.

An acute cough-specific quality of life questionnaire for children: Development and validation

Background Patient-relevant outcome measures are essential for high-quality clinical research, and quality-of-life (QoL) tools are the current standard. Currently, there is no validated children's acute cough-specific QoL questionnaire. Objective The objective of this study was to develop and validate the Parent-proxy Children's Acute Cough-specific QoL Questionnaire (PAC-QoL). Methods Using focus groups, a 48-item PAC-QoL questionnaire was developed and later reduced to 16 items by using the clinical impact method. Parents of children with a current acute cough (<2 weeks) at enrollment completed 2 validated cough score measures, the preliminary 48-item PAC-QoL, and 3 other questionnaires (the State Trait Anxiety Inventory [STAI], the Short-Form 8-item 24-hour recall Health Survey [SF-8], and the Depression, Anxiety, and Stress 21-item Scale [DASS21]). All measures were repeated on days 3 and 14. Results The median age of the 155 children enrolled was 2.3 years (interquartile range, 1.3-4.6). Median cough duration at enrollment was 3 days (interquartile range, 2-5). The reduced 16-item scale had high internal consistency (Cronbach α = 0.95). Evidence for repeatability and criterion validity was shown by significant correlations between the domains and total PAC-QoL scores and the SF-8 (r = −0.36 and −0.51), STAI (r = −0.27 and −0.39), and DASS21 (r = −0.32 and −0.41) scales on days 0 and 3, respectively. The final PAC-QoL questionnaire was sensitive to change over time, with changes significantly relating to changes in cough score measures (P < .001). Conclusion The 16-item PAC-QoL is a reliable and valid outcome measure that assesses QoL related to childhood acute cough at a given time point and reflects changes in acute cough-specific QoL over time.

Old mastheads and new media : newspapers striving to adapt in Australia and South-east Asia

As a key element in their response to new media forcing transformations in mass media and media use, newspapers have deployed various strategies to not only establish online and mobile products, and develop healthy business plans, but to set out to be dominant portals. Their response to change was the subject of an early investigation by one of the present authors (Keshvani 2000). That was part of a set of short studies inquiring into what impact new software applications and digital convergence might have on journalism practice (Tickle and Keshvani 2000), and also looking for demonstrations of the way that innovations, technologies and protocols then under development might produce a “wireless, streamlined electronic news production process (Tickle and Keshvani 2001).” The newspaper study compared the online products of The Age in Melbourne and the Straits Times in Singapore. It provided an audit of the Singapore and Australia Information and Communications Technology (ICT) climate concentrating on the state of development of carrier networks, as a determining factor in the potential strength of the two services with their respective markets. In the outcome, contrary to initial expectations, the early cable roll-out and extensive ‘wiring’ of the city in Singapore had not produced a level of uptake of Internet services as strong as that achieved in Melbourne by more ad hoc and varied strategies. By interpretation, while news websites and online content were at an early stage of development everywhere, and much the same as one another, no determining structural imbalance existed to separate these leading media participants in Australia and South-east Asia. The present research revisits that situation, by again studying the online editions of the two large newspapers in the original study, and one other, The Courier Mail, (recognising the diversification of types of product in this field, by including it as a representative of Newscorp, now a major participant). The inquiry works through the principle of comparison. It is an exercise in qualitative, empirical research that establishes a comparison between the situation in 2000 as described in the earlier work, and the situation in 2014, after a decade of intense development in digital technology affecting the media industries. It is in that sense a follow-up study on the earlier work, although this time giving emphasis to content and style of the actual products as experienced by their users. It compares the online and print editions of each of these three newspapers; then the three mastheads as print and online entities, among themselves; and finally it compares one against the other two, as representing a South-east Asian model and Australian models. This exercise is accompanied by a review of literature on the developments in ICT affecting media production and media organisations, to establish the changed context. The new study of the online editions is conducted as a systematic appraisal of the first level, or principal screens, of the three publications, over the course of six days (10-15.2.14 inclusive). For this, categories for analysis were made, through conducting a preliminary examination of the products over three days in the week before. That process identified significant elements of media production, such as: variegated sourcing of materials; randomness in the presentation of items; differential production values among media platforms considered, whether text, video or stills images; the occasional repurposing and repackaging of top news stories of the day and the presence of standard news values – once again drawn out of the trial ‘bundle’ of journalistic items. Reduced in this way the online artefacts become comparable with the companion print editions from the same days. The categories devised and then used in the appraisal of the online products have been adapted to print, to give the closest match of sets of variables. This device, to study the two sets of publications on like standards -- essentially production values and news values—has enabled the comparisons to be made. This comparing of the online and print editions of each of the three publications was set up as up the first step in the investigation. In recognition of the nature of the artefacts, as ones that carry very diverse information by subject and level of depth, and involve heavy creative investment in the formulation and presentation of the information; the assessment also includes an open section for interpreting and commenting on main points of comparison. This takes the form of a field for text, for the insertion of notes, in the table employed for summarising the features of each product, for each day. When the sets of comparisons as outlined above are noted, the process then becomes interpretative, guided by the notion of change. In the context of changing media technology and publication processes, what substantive alterations have taken place, in the overall effort of news organisations in the print and online fields since 2001; and in their print and online products separately? Have they diverged or continued along similar lines? The remaining task is to begin to make inferences from that. Will the examination of findings enforce the proposition that a review of the earlier study, and a forensic review of new models, does provide evidence of the character and content of change --especially change in journalistic products and practice? Will it permit an authoritative description on of the essentials of such change in products and practice? Will it permit generalisation, and provide a reliable base for discussion of the implications of change, and future prospects? Preliminary observations suggest a more dynamic and diversified product has been developed in Singapore, well themed, obviously sustained by public commitment and habituation to diversified online and mobile media services. The Australian products suggest a concentrated corporate and journalistic effort and deployment of resources, with a strong market focus, but less settled and ordered, and showing signs of limitations imposed by the delay in establishing a uniform, large broadband network. The scope of the study is limited. It is intended to test, and take advantage of the original study as evidentiary material from the early days of newspaper companies’ experimentation with online formats. Both are small studies. The key opportunity for discovery lies in the ‘time capsule’ factor; the availability of well-gathered and processed information on major newspaper company production, at the threshold of a transformational decade of change in their industry. The comparison stands to identify key changes. It should also be useful as a reference for further inquiries of the same kind that might be made, and for monitoring of the situation in regard to newspaper portals on line, into the future.