Optimization of three-dimensional branching networks of microchannels for thermal management of microelectronics

The aim of this work is to present a methodology to develop cost-effective thermal management solutions for microelectronic devices, capable of removing maximum amount of heat and delivering maximally uniform temperature distributions. The topological and geometrical characteristics of multiple-story three-dimensional branching networks of microchannels were developed using multi-objective optimization. A conjugate heat transfer analysis software package and an automatic 3D microchannel network generator were developed and coupled with a modified version of a particle-swarm optimization algorithm with a goal of creating a design tool for 3D networks of optimized coolant flow passages. Numerical algorithms in the conjugate heat transfer solution package include a quasi-ID thermo-fluid solver and a steady heat diffusion solver, which were validated against results from high-fidelity Navier-Stokes equations solver and analytical solutions for basic fluid dynamics test cases. Pareto-optimal solutions demonstrate that thermal loads of up to 500 W/cm2 can be managed with 3D microchannel networks, with pumping power requirements up to 50% lower with respect to currently used high-performance cooling technologies.

Investigation of spatial patterns of ground-water exchange with lakes, using a three-dimensional numerical model

Hydrogeologic variables controlling groundwater exchange with inflow and flow-through lakes were simulated using a three-dimensional numerical model (MODFLOW) to investigate and quantify spatial patterns of lake bed seepage and hydraulic head distributions in the porous medium surrounding the lakes. Also, the total annual inflow and outflow were calculated as a percentage of lake volume for flow-through lake simulations. The general exponential decline of seepage rates with distance offshore was best demonstrated at lower anisotropy ratio (i.e., Kh/Kv = 1, 10), with increasing deviation from the exponential pattern as anisotropy was increased to 100 and 1000. 2-D vertical section models constructed for comparison with 3-D models showed that groundwater heads and seepages were higher in 3-D simulations. Addition of low conductivity lake sediments decreased seepage rates nearshore and increased seepage rates offshore in inflow lakes, and increased the area of groundwater inseepage on the beds of flow-through lakes. Introduction of heterogeneity into the medium decreased the water table and seepage ratesnearshore, and increased seepage rates offshore in inflow lakes. A laterally restricted aquifer located at the downgradient side of the flow-through lake increased the area of outseepage. Recharge rate, lake depth and lake bed slope had relatively little effect on the spatial patterns of seepage rates and groundwater exchange with lakes.

Comparison of radiobiological effects induced by ultra-high and standard dose rate of x-rays on a radio-resistant cell line

Radiotherapy (RT) has recently evolved with the emergence of heavy ion radiations or new fractionation schemes of photon therapy, which modify the dose rate of treatment delivery. The aim of the present study was then to evaluate the in vitro influence of a ultra-high dose rate comparing them with standard dose rate. In this regard, a radioresistant SK-MEL-28 cell line were irradiated with x-ray in order to have a total dose of 2 and 4 Gy, at two different dose rate. The ultra-high dose rate is a specific property of the dense plasma focus (DPF) device, which has pulsed operation and thus gives short and highly energetic pulses of multiple types of rays and particles, in this case, we focused our study on the influence of X-rays. While a low dose rate is obtained with conventional X-ray tube. In this study it results that a ultra-high dose rate enhances radiosensitivity of melanoma cells while reducing the adhesion, proliferation and migration ability of cells.

Three-dimensional outcomes of twin-block appliance treatment and the influence of the postured wax bite

Aims 1 To identify the 3D soft tissue volumetric and linear landmark changes following treatment with the Twin-Block Appliance TBA. 2 To estimate the TBA treatment outcome on the soft tissue facial profile volumetric and linear landmark changes from the Postured Wax Bite (PWB). 3 To identify if there is any association between certain soft tissue landmark variables and successful treatment outcome of the TBA as measured by the reduction in overjet. 4 To assess the effects of TBA treatment on facial expressions. Materials and Methods Forty-seven Caucasian subjects with Class II division 1 were recruited. 3D images captured of each subject, pre-treatment (T1), with the PWB (T2) and at the end of treatment (T3). Soft tissue volumetric and linear changes as well as the correlation between facial parameters and successful treatment were calculated. Results The mean soft tissue volumetric change from T1 to T3 was 22.24 ± 16.73 cm³. Soft tissue profile linear changes from T1-T3 for lower facial landmarks were 4-5 mm. From T1-T3, the mean soft tissue volumetric change of the total sample was 60% of the change produced by the PWB (T1 to T2). Correlations were weak for all 3D facial parameters and successful overjet reduction. Facial expression changes were only significant for the lower landmarks. Conclusions 1 TBA treatment, in growing subjects, increased the lower facial soft tissue volume and caused forward movement of the lower soft tissue facial profile landmarks.2 The PWB can be used to estimate the treatment outcome of the TBA on soft tissue profile changes.3 No association was found between soft tissue landmark variables and successful overjet reduction.4 TBA treatment had no effect on the upper facial landmarks for each facial expression but it changed the lower facial expressions significantly except for maximal smile in males.

Relationship between surface topography and energy density distribution of Er, Cr:YSGG beam on irradiated dentin: an atomic force microscopy study

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A three dimensional finite volume approach to the thermo-mechanical modelling of the shape casting of metals

This paper presents a three dimensional, thermos-mechanical modelling approach to the cooling and solidification phases associated with the shape casting of metals ei. Die, sand and investment casting. Novel vortex-based Finite Volume (FV) methods are described and employed with regard to the small strain, non-linear Computational Solid Mechanics (CSM) capabilities required to model shape casting. The CSM capabilities include the non-linear material phenomena of creep and thermo-elasto-visco-plasticity at high temperatures and thermo-elasto-visco-plasticity at low temperatures and also multi body deformable contact with which can occur between the metal casting of the mould. The vortex-based FV methods, which can be readily applied to unstructured meshes, are included within a comprehensive FV modelling framework, PHYSICA. The additional heat transfer, by conduction and convection, filling, porosity and solidification algorithms existing within PHYSICA for the complete modelling of all shape casting process employ cell-centred FV methods. The termo-mechanical coupling is performed in a staggered incremental fashion, which addresses the possible gap formation between the component and the mould, and is ultimately validated against a variety of shape casting benchmarks.

On precise three-dimensional environment modeling via UAV-based photogrammetric systems

Abstract : Images acquired from unmanned aerial vehicles (UAVs) can provide data with unprecedented spatial and temporal resolution for three-dimensional (3D) modeling. Solutions developed for this purpose are mainly operating based on photogrammetry concepts, namely UAV-Photogrammetry Systems (UAV-PS). Such systems are used in applications where both geospatial and visual information of the environment is required. These applications include, but are not limited to, natural resource management such as precision agriculture, military and police-related services such as traffic-law enforcement, precision engineering such as infrastructure inspection, and health services such as epidemic emergency management. UAV-photogrammetry systems can be differentiated based on their spatial characteristics in terms of accuracy and resolution. That is some applications, such as precision engineering, require high-resolution and high-accuracy information of the environment (e.g. 3D modeling with less than one centimeter accuracy and resolution). In other applications, lower levels of accuracy might be sufficient, (e.g. wildlife management needing few decimeters of resolution). However, even in those applications, the specific characteristics of UAV-PSs should be well considered in the steps of both system development and application in order to yield satisfying results. In this regard, this thesis presents a comprehensive review of the applications of unmanned aerial imagery, where the objective was to determine the challenges that remote-sensing applications of UAV systems currently face. This review also allowed recognizing the specific characteristics and requirements of UAV-PSs, which are mostly ignored or not thoroughly assessed in recent studies. Accordingly, the focus of the first part of this thesis is on exploring the methodological and experimental aspects of implementing a UAV-PS. The developed system was extensively evaluated for precise modeling of an open-pit gravel mine and performing volumetric-change measurements. This application was selected for two main reasons. Firstly, this case study provided a challenging environment for 3D modeling, in terms of scale changes, terrain relief variations as well as structure and texture diversities. Secondly, open-pit-mine monitoring demands high levels of accuracy, which justifies our efforts to improve the developed UAV-PS to its maximum capacities. The hardware of the system consisted of an electric-powered helicopter, a high-resolution digital camera, and an inertial navigation system. The software of the system included the in-house programs specifically designed for camera calibration, platform calibration, system integration, onboard data acquisition, flight planning and ground control point (GCP) detection. The detailed features of the system are discussed in the thesis, and solutions are proposed in order to enhance the system and its photogrammetric outputs. The accuracy of the results was evaluated under various mapping conditions, including direct georeferencing and indirect georeferencing with different numbers, distributions and types of ground control points. Additionally, the effects of imaging configuration and network stability on modeling accuracy were assessed. The second part of this thesis concentrates on improving the techniques of sparse and dense reconstruction. The proposed solutions are alternatives to traditional aerial photogrammetry techniques, properly adapted to specific characteristics of unmanned, low-altitude imagery. Firstly, a method was developed for robust sparse matching and epipolar-geometry estimation. The main achievement of this method was its capacity to handle a very high percentage of outliers (errors among corresponding points) with remarkable computational efficiency (compared to the state-of-the-art techniques). Secondly, a block bundle adjustment (BBA) strategy was proposed based on the integration of intrinsic camera calibration parameters as pseudo-observations to Gauss-Helmert model. The principal advantage of this strategy was controlling the adverse effect of unstable imaging networks and noisy image observations on the accuracy of self-calibration. The sparse implementation of this strategy was also performed, which allowed its application to data sets containing a lot of tie points. Finally, the concepts of intrinsic curves were revisited for dense stereo matching. The proposed technique could achieve a high level of accuracy and efficiency by searching only through a small fraction of the whole disparity search space as well as internally handling occlusions and matching ambiguities. These photogrammetric solutions were extensively tested using synthetic data, close-range images and the images acquired from the gravel-pit mine. Achieving absolute 3D mapping accuracy of 11±7 mm illustrated the success of this system for high-precision modeling of the environment.

Conceptualising cosmopolitanism and entrepreneurship through the lens of the three-dimensional theory of power

Purpose – The paper aims to conceptualise cosmopolitanism drivers from the third-level power perspective by drawing on Lukes’ (1974; 2005) theory of power. In addition, the paper aims to investigate the relationship between entrepreneurs’ cosmopolitan dispositions and habitus, i.e. a pattern of an individual’s demeanour, as understood by Bourdieu. Design/methodology/approach – This conceptual paper makes use of Bourdieu’s framework (habitus) by extending it to the urban cosmopolitan environment and linking habitus to the three-dimensional theory of power and, importantly, to the power’s third dimension – preference-shaping. Findings – Once cosmopolitanism is embedded in the urban area’s values, this creates multiple endless rounds of mutual influence (by power holders onto entrepreneurs via political and business elites, and by entrepreneurs onto power holders via the same channels), with mutual benefit. Therefore, mutually beneficial influence that transpires in continuous support of a cosmopolitan city’s environment may be viewed as one of the factors that enhances cosmopolitan cities’ resilience to changes in macroeconomic conditions. Originality/value – The paper offers a theoretical model that enriches the understanding of the power-cosmopolitanism-entrepreneurship link, by emphasising the preference-shaping capacity of power, which leads to the embedment of cosmopolitanism in societal values. As a value shared by political and business elites, cosmopolitanism is also actively promoted by entrepreneurs through their disposition and habitus. This ensures not only their willing compliance with power and the environment, but also their enhancement of favourable business conditions. Entrepreneurs depart from mere acquiescence (to power and its explicit dominance), and instead practice their cosmopolitan influence by active preference-shaping.

Partition alignment in three dimensional unstructured mesh multi-physics modelling

Unstructured mesh codes for modelling continuum physics phenomena have evolved to provide the facility to model complex interacting systems. Parallelisation of such codes using single Program Multi Data (SPMD) domain decomposition techniques implemented with message passing has been demonstrated to provide high parallel efficiency, scalability to large numbers of processors P and portability across a wide range of parallel platforms. High efficiency, especially for large P requires that load balance is achieved in each parallel loop. For a code in which loops span a variety of mesh entity types, for example, elements, faces and vertices, some compromise is required between load balance for each entity type and the quantity of inter-processor communication required to satisfy data dependence between processors.

Geometrical measurements in three-dimensional quantum gravity

A set of observables is described for the topological quantum field theory which describes quantum gravity in three space-time dimensions with positive signature and positive cosmological constant. The simplest examples measure the distances between points, giving spectra and probabilities which have a geometrical interpretation. The observables are related to the evaluation of relativistic spin networks by a Fourier transform.

Three dimensional models of water flow in the Persian Gulf

Persian Gulf region is globally of great importance due to its economical and political reasons. The importance lies in oil sources and sea exports. Geophysical phenomena dominated in the water circulation affected this region is called Monsoon it stretches from African coasts to the half way of Red Seal affected all coasts of Persian Gulf and goes toward east to the Indian ocean. Other essential factors in the water circulation in this region are net evaporation (several meters in per year), high density and high salinity. In this article the effects of wind stress and evaporation in the water circulation in the region will be considered and model equations for wind forces, density, pressure, gradient, and bottom friction for Persian Gulf will be discussed.

Three-dimensional, in-silico breast phantom for multimodality image simulations

We report on the construction of anatomically realistic three-dimensional in-silico breast phantoms with adjustable sizes, shapes and morphologic features. The concept of multiscale spatial resolution is implemented for generating breast tissue images from multiple modalities. Breast epidermal boundary and subcutaneous fat layer is generated by fitting an ellipsoid and 2nd degree polynomials to reconstructive surgical data and ultrasound imaging data. Intraglandular fat is simulated by randomly distributing and orienting adipose ellipsoids within a fibrous region immediately within the dermal layer. Cooper’s ligaments are simulated as fibrous ellipsoidal shells distributed within the subcutaneous fat layer. Individual ductal lobes are simulated following a random binary tree model which is generated based upon probabilistic branching conditions described by ramification matrices, as originally proposed by Bakic et al [3, 4]. The complete ductal structure of the breast is simulated from multiple lobes that extend from the base of the nipple and branch towards the chest wall. As lobe branching progresses, branches are reduced in height and radius and terminal branches are capped with spherical lobular clusters. Biophysical parameters are mapped onto the complete anatomical model and synthetic multimodal images (Mammography, Ultrasound, CT) are generated for phantoms of different adipose percentages (40%, 50%, 60%, and 70%) and are analytically compared with clinical examples. Results demonstrate that the in-silico breast phantom has applications in imaging performance evaluation and, specifically, great utility for solving image registration issues in multimodality imaging.

The three dimensional model with the affection of stratified density (Caspian Sea)

The hydro dynamical actions in big Lakes directly influence dynamic, physical and chemical affairs. The circulation's models and temperature have something to do with the movements of fluids, and analysis for circulation in Caspian sea is because of the lack of observation through which the circulations and out comings are determined. Through the studies, three dimensional simulations (Large- Scale) are planned and performed, according to Smolakiewicz and Margolin works. This is a non- hydrostatic and Boussinesq approximation is used in its formulation is used in its formulation on the basis of Lipps (1990) theorem and curve lines, the fluid is constant adiabatic and stratified, and the wind power is considered zero. The profile of speed according to previous depth and before ridge can be drawn on the basis of density available between northern and southern ridges. The circulation field is drawn from 3 cm/s to 13 cm/s on the plate z= 5 cm , the vertical changes of speed on the plate is 0.02 m/s. Vertical profile , horizontal speed in previous on, and after the ridges on are drawn on different spaces. It changes from 0.5 cm/s to 1 cm/s before ridges.

Three dimensional visualization of the World Wide Web

Although large-scale public hypermedia structures such as the World Wide Web are popularly referred to as "cyberspace", the extent to which they constitute a space in the everyday sense of the word is questionable. This paper reviews recent work in the area of three dimensional (3D) visualization of the Web that has attempted to depict it in the form of a recognizable space; in other words, as a navigable landscape that may be visibly populated by its users. Our review begins by introducing a range of visualizations that address different aspects of using the Web. These include visualizations of Web structure, especially of links, that act as 3D maps; browsing history; searches; evolution of the Web; and the presence and activities of multiple users. We then summarize the different techniques that are employed by these visualizations. We conclude with a discussion of key challenges for the future.

Coupling of Chemical Kinetics with Computational Fluid Dynamics in a Three-Dimensional Engine Model

The role of computer modeling has grown recently to integrate itself as an inseparable tool to experimental studies for the optimization of automotive engines and the development of future fuels. Traditionally, computer models rely on simplified global reaction steps to simulate the combustion and pollutant formation inside the internal combustion engine. With the current interest in advanced combustion modes and injection strategies, this approach depends on arbitrary adjustment of model parameters that could reduce credibility of the predictions. The purpose of this study is to enhance the combustion model of KIVA, a computational fluid dynamics code, by coupling its fluid mechanics solution with detailed kinetic reactions solved by the chemistry solver, CHEMKIN. As a result, an engine-friendly reaction mechanism for n-heptane was selected to simulate diesel oxidation. Each cell in the computational domain is considered as a perfectly-stirred reactor which undergoes adiabatic constant- volume combustion. The model was applied to an ideally-prepared homogeneous- charge compression-ignition combustion (HCCI) and direct injection (DI) diesel combustion. Ignition and combustion results show that the code successfully simulates the premixed HCCI scenario when compared to traditional combustion models. Direct injection cases, on the other hand, do not offer a reliable prediction mainly due to the lack of turbulent-mixing model, inherent in the perfectly-stirred reactor formulation. In addition, the model is sensitive to intake conditions and experimental uncertainties which require implementation of enhanced predictive tools. It is recommended that future improvements consider turbulent-mixing effects as well as optimization techniques to accurately simulate actual in-cylinder process with reduced computational cost. Furthermore, the model requires the extension of existing fuel oxidation mechanisms to include pollutant formation kinetics for emission control studies.