High prevalence of methicillin resistance and PVL genes amongStaphylococcus aureus isolates from the nares and skin lesions of pediatric patients with atopic dermatitis

Staphylococcus aureus is highly prevalent among patients with atopic dermatitis (AD), and this pathogen may trigger and aggravate AD lesions. The aim of this study was to determine the prevalence of S. aureus in the nares of pediatric subjects and verify the phenotypic and molecular characteristics of the isolates in pediatric patients with AD. Isolates were tested for antimicrobial susceptibility, SCCmectyping, and Panton-Valentine Leukocidin (PVL) genes. Lineages were determined by pulsed-field gel electrophoresis and multilocus sequence typing (MLST). AD severity was assessed with the Scoring Atopic Dermatitis (SCORAD) index. Among 106 patients, 90 (85%) presented S. aureus isolates in their nares, and 8 also presented the pathogen in their skin infections. Two patients had two positive lesions, making a total of 10 S. aureusisolates from skin infections. Methicillin-resistant S. aureus(MRSA) was detected in 24 (26.6%) patients, and PVL genes were identified in 21 (23.3%), including 6 (75%) of the 8 patients with skin lesions but mainly in patients with severe and moderate SCORAD values (P=0.0095). All 24 MRSA isolates were susceptible to trimethoprim/sulfamethoxazole, while 8 isolates had a minimum inhibitory concentration (MIC) to mupirocin >1024 μg/mL. High lineage diversity was found among the isolates including USA1100/ST30, USA400/ST1, USA800/ST5, ST83, ST188, ST718, ST1635, and ST2791. There was a high prevalence of MRSA and PVL genes among the isolates recovered in this study. PVL genes were found mostly among patients with severe and moderate SCORAD values. These findings can help clinicians improve the therapies and strategies for the management of pediatric patients with AD.

Comparação das técnicas de cromatografia em camada delgada e ELISA na quantificação de aflatoxinas em amostras de milho

A comparação das técnicas de Enzyme Linked Immunosorbent Assay (ELISA) e cromatografia em camada delgada (CCD) por quantificação visual e densitométrica foi utilizada na determinação de aflatoxina total, em amostras de milho naturalmente contaminadas. Os teores de aflatoxina total encontrados pelas técnicas de CCD e ELISA, apresentaram maior freqüência na faixa de 0-30 mig/kg e acima de 300 mig/kg. Os resultados das amostras apresentaram coeficiente de variação concentrados abaixo de 20, 30 e 40% para a técnica de ELISA e CCD com quantificação densitométrica e visual, respectivamente. Os coeficientes de correlação foram altamente significativos para as relações entre as quantificações visual e densitométrica (r = 0,9219; t = 26,36; p < 0,001), ELISA e visual (r = 0,8277; t = 17,58; p < 0,001), ELISA e densitometria (r = 0,7373; t = 13,01; p < 0,001), na determinação de aflatoxina total em todas as amostras de milho pesquisadas, confirmando haver equivalência das técnicas estudadas.

Lignin oxidation by PCD technology

The purpose of this study is to investigate whether commercial Kraft lignin can be treated with pulsed corona discharge apparatus so that it becomes active. Active lignin refers to the kind of lignin that can be precipitated on the surface of a fiber by lowering the pH. A secondary agenda here is to remove the pungent smell of kraft lignin, which is caused by organically bound sulfur. It is expected that the study will identify mild processing conditions and parameters for achievement of the desired outcome. In the literature review, the properties of lignin are explained, as is their impact on any further processing. In addition, a number of processes are described for the oxidation of lignin in a variety of applications. In the experimental part of the study, test runs were conducted to determine the effects of oxygen supply and pulse frequency on oxidation results, where the purpose is to produce reactive lignin and to find a process that is feasible at an industrial scale. Based on the reported experiments, lignin could not be made active or precipitated to the surface of the fiber. Actual changes in the structure of lignin were not observed, but the pungent smell of lignin was removed. The exact reason for this change could not be established because sulfur NMR analysis did not work for the lignin samples.

Modifioidun MAG-kaarihitsausprosessin hyödyntäminen railotilavuuden pienentämisessä mekanisoidussa orbitaalihitsauksessa.

Länsimaisen työn hinta luo jatkuvan paineen hitsauksen tuottavuuden parantamiseen. MIG/MAG-hitsauksen tuottavuutta voidaan parantaa tehostamalla hitsausprosessia, vähentämällä hitsien lukumäärää ja pienentämällä hitsiaineen tarvetta. Eri virtalähdevalmistajat tuovat markkinoille hitsausprosesseja hitsauksen tehostamiseen, joilla pystytään korvata vähemmän tuottavia hitsaustyövaiheita. Hitsien lukumäärän vähentäminen on rakenteen suunnitteluun liittyvä tekijä ja hitsiaineen tarpeen pienentäminen voidaan toteuttaa railogeometrian muutoksilla tai tuotteen sopivalla suunnittelulla. Diplomityössä on tutkittu 30 mm paksujen S355 rakenneteräsputkien hitsauksen tuottavuuden kasvattamista käyttäen nykyaikaisia modifioituja kaarihitsausprosesseja ja railotilavuutta pienentämällä. Työssä vertailtiin 30o ja 60o railokulmalla tehtyjä liitoksia. Railogeometrian muutoksen lisäksi diplomityössä vertailtiin eri menetelmien tehokkuutta putken pohjapalon hitsauksessa.

The Role of Structural Imperfections in Sr2FeMoO6 Thin Films

In this work, Sr2FeMoO6 (SFMO) thin films were studied with the main focus on their magnetic and magneto-transport properties. The fabrication process of pulsed laser deposited SFMO films was first optimized. Then the effects of strain, film thickness and substrate were thoroughly investigated. In addition to these external factors, the effect of intrinsic defects on the magnetic properties of SFMO were also clarified. Secondly, the magnetoresistivity mechanims of SFMO films were studied and a semiempirical model of the temperature dependence of resistivity was introduced. The films were grown on single crystal substrates using a ceramic target made with sol-gel method. The structural characterization of the films were carried out with X-ray diffraction, atomic force microscopy, transmission electron microscopy and high kinetic energy photoelectron spectroscopy. The magnetic properties were measured with SQUID magnetometer and the magneto-transport properties by magnetometer with a resistivity option. SFMO films with the best combination of structural and magnetic properties were grown in Ar atmosphere at 1050 °C . Their magnetic properties could not be improved by the ex situ post-annealing treatments aside from the treatments in ultra-high vacuum conditions. The optimal film thickness was found to be around 150 nm and only small improvement in the magnetic properties with decreasing strain was observed. Instead, the magnetic properties were observed to be highly dependent on the choice of the substrate due to the lattice mismatch induced defects, which are best avoided by using the SrTiO3 substrate. The large difference in the Curie temperature and the saturation magnetization between the SFMO thin film and polycrystalline bulk samples was connected to the antisite disorder and oxygen vacancies. Thus, the Curie temperature of SFMO thin films could be improved by increasing the amount of oxygen vacancies for example with ultra-high vacuum treatments or improving the B-site ordering by further optimization of the deposition parameters. The magneto-transport properties of SFMO thin films do not follow any conventional models, but the temperature dependence of resistivity was succesfully described with a model of two spin channel system. Also, evidences that the resistivity-temperature behaviour of SFMO thin films is dominated by the structural defects, which reduce the band gap in the majority spin band were found. Moreover, the magnetic field response of the resistivity in SFMO thin films were found to be superposition of different mechanisms that seems to be related to the structural changes in the film.

Barns rädslor i förskolan: en studie av förskolebarns rädslor i förskolemiljö och vardag

I min empiriska undersökning är huvudsyftet att redogöra för förskolebarns rädslor i vardagen. I min undersökning deltog 54 respondenter från olika österbottniska förskolor. Jag har använt mig av intervju och teckning för att samla in datamaterial. Inledningsvis skulle eleverna rita en teckning av deras tankar om rädsla. Följande moment bestod av att varje enskild elev blev intervjuad och jag kunde få en djupare förståelse av vad förskolebarnen hade tecknat. Teckningarna fungerade som ett diskussionsunderlag till mina intervjufrågor. Det insamlade datamaterialet är kvalitativt men kan också betraktas som kvantitativt i resultatanalysen med de procentuella enheterna. Studien har grundats på följande frågeställningar: 1) Vilka rädslor har förskolebarn? a) Hur beskriver de dem i ord? b) Hur beskriver de dem i teckning? 2) Hur hanterar förskolebarn sina rädslor? I undersökningen framkom det att alla barn har en känsla om hur rädsla uppfattas och att barnen har en rädsla för någonting. De flesta rädslorna eleverna upplever är rädsla för ormar och spindlar, som räknas till kategorin rädslor som finns nära och är realistiska. En annan rädsla i kategorin nära men inte realistiska är björnar och vargar. Kategorin rädslor som är på distans och inte realistiska är rädsla för spöken. Den sista kategorin med rädslor som är nära men inte realistiska är rädsla för mörker. Resultaten hur barnen hanterar sina rädslor fann jag speciellt intressanta, eftersom det inte är så många barn som vänder sig till en vuxen för att be om hjälp med sina rädslor. De barn som ville behandla sina rädslor tyckte det bästa alternativet var genom att samtala med en vuxen. Vidare finner jag ett intresse av likheterna jag finner i min undersökning och Sylvia Gustavssons avhandling om barns rädslor i förskole och skolåldern och pedagogers och arbetsförhållningssätt. Där finns det likheter i resultaten hur eleverna skrämmer bort rädslan. Resultaten visar att de flesta av barnens svar finns i kategorin med rädslor som finns nära dem och är realistiska, t.ex. rädsla för humlor och bin. Det framkommer även i resultaten att alla förskolebarn har en känsla av hur rädsla upplevs.

Enhancement of ultrafiltration process by pretreatment in recovery of hemicelluloses from wood extracts

Hemicelluloses are potential raw material for several items produced in future wood-based biorefineries. One possible method for recovering hemicelluloses from wood extracts is ultrafiltration (UF). However, low filtration capacities and severe fouling restrict the use of tight UF membranes in the treatment of wood extracts. The lack of suitable commercial membranes creates a need for pretreatment which would decrease fouling and increase the filtration capacity. This thesis focuses on the evaluation of the possibility to improve the filtration capacity and decrease fouling with the pretreatment of wood extracts. Methods which remove harmful compounds and methods which degrade them are studied, as well as combinations of the methods. The tested pretreatments have an influence on both the concentration of different compounds and the molecular mass distribution of the compounds in the extract. This study revealed that in addition to which kind of compounds were removed, also the change in molecular size distribution affected the filtration capacity significantly. It was shown that the most harmful compounds for the filtration capacity of the hydrophobic 5 kDa membrane were the ones capable of permeating the membrane and fouling also the inner membrane structure. Naturally, the size of the most harmful compounds depends on the used UF membrane and is thus case-specific. However, in the choice of the pretreatment method, the focus should be on the removal of harmful compound sizes rather than merely on the total amount of removed foulants. The results proved that filtration capacity can be increased with both adsorptive and oxidative pretreatments even by hundreds of per cents. For instance, the use of XAD7 and XAD16 adsorbents increased the average flux in the UF of a birch extract from nearly zero to 107 kg/(m2h) and 175 kg/(m2h), respectively. In the treatment of a spruce extract, oxidation by pulsed corona discharge (PCD) increased the flux in UF from 46 kg/(m2h) to 158 kg/(m2h). Moreover, when a birch extract batch was treated with laccase enzyme, the flux in UF increased from 15 kg/(m2h) to 36 kg/(m2h). However, fouling was decreased only by adsorptive pretreatment while oxidative methods had a negligible or even negative impact on it. This demonstrates that filtration capacity and fouling are affected by different compounds and mechanisms. The results of this thesis show that filtration capacity can be improved and fouling decreased through appropriate pretreatment. However, the choice of the best possible pretreatment is case-specific and depends on the wood extract and the membrane used. Finding the best option requires information on the extract content and membrane characteristics as well as on the filtration performance of the membrane in the prevailing conditions and a multivariate approach. On the basis of this study, it can be roughly concluded that adsorptive pretreatment improves the filtration capacity and decreases fouling rather reliably, but it may lead to significant hemicellulose losses. Oxidation reduces the loss of valuable hemicelluloses and could improve the filtration capacity, but fouling challenges may remain. Combining oxidation with adsorptive pretreatment was not a solution for avoiding hemicellulose losses in the tested cases.

Methodus informandi in paedagogiis tam ruralibus quam urbicis. Nec non scholis trivialibus, per dioecesin Aboensem: prius qvidem per partes exhibita; jam verò necessitate ita efflagitante, et ad desiderium multorum typis exscripta

Arkit: A-B4 C2.

Ny ABC- och läsebok för barn: tillegnad fäderneslandets mödrar af P. U. F. Sadelin

Nimiösivulla myös motto: Kommer hit, barn! hörer mig! ... Ps. 34:12.

Laser- plasma- hybridihitsauksen käytettävyys teollisuudessa

Hybridihitsaukseksi nimitetään yleensä hitsausprosesseja, joissa yhdistetään kaari- ja laserhitsauksen vahvuudet. Laser- MIG/MAG- prosessit ovat näistä selvästi yleisimpiä, mutta muillekin prosesseille on sovelluksia. Tässä kandidaatintyössä on arvioitu laser- plasma- hybridihitsausprosessin käytettävyyttä teollisuuden prosesseissa. Arviointi on tehty vertailevana kirjallisuustutkimuksena laser- plasma- hybridiprosessin, laserhitsauksen, sekä muiden laser- hybridihitsausprosessien kesken. Prosessien vertailun lisäksi työssä on käsitelty hybridihitsausprosessien parametrien valintaa ja laser- plasma- hybridiprosessin erityispiirteitä.

Pulssitettu laserablaatio mikrofluidisten kanavistojen sarjatuotantomenetelmänä

Puolijohteiden yleistyttyä vuodesta 1948 alkaen, ovat elektroniset laitteet pienentyneet jatkuvasti tehojen kuitenkin kasvaessa. Kasvaneet tehotiheydet kuitenkin vaikeuttavat laitesuunnittelua, sillä puoljohdekomponenttien suorituskyvylle ja eliniälle on oleellista lämpötilojen ja lämpötilavaihteluiden minimointi. Perinteisen ilmajäähdytyksen lähestyessä rajojaan niin kokonaistehon kuin järkevän energiatehokkuudenkin suhteen, on parhaaksi seuraavaksi teknologiaksi ennustettu kaksifaasijäähdytystä, jonka suorituskyky ja energiatehokkuus ovat vaaditulla tasolla. Kaksifaasijäähdytyksen optimaaliselle toiminnalle tärkeää on hyvin suunniteltu ja tarkasti valmistettu lämmönsiirtopinta, jota kutsutaan mikrokanavistoksi. Pulssitettu laserkaiverrus on edistynyt valmistustekniikka, jonka tarkkuus ja luotettavuus sopisivat mikrokanavistojen valmistamiseen. Laserkaiverruksella saavutettavat lopputulokset vaihtelevat kuitenkin materiaalista riippuen ja kupari – jota käytetään yleisesti lämmönjohteena – on eräs huonoimmin lasertyöstöön reagoivista materiaaleista ja siksi on oleellista selvittää laser-kaiverruksen toimivuutta kuparisten mikrokanavistojen valmistuksessa. Pulssitetun laser-kaiverruksen eri variaatioista nanosekunti-luokan pulssinpituuksilla toimivat laitteet ovat jatkuvan tuotannon kannalta paras vaihtoehto niiden hyvän tuottavuuden, saatavuuden sekä kohtuullisen alkuinvestoinnin vuoksi. Käytännön kaiverruskokeiden perusteella selvisi, että menetelmä on laatunsa ja tarkkuutensa puolesta sopiva varsinaiseen tuotantoon. Kaiverruksen tehokkuus kuparia työstettäessä on kuitenkin ennakoituakin heikompi ja niin valmistus- kuin suunnitelu-prosessikin vaativat vielä jatkotutkimusta ja -kehitystä.

Ultralujan teräksen kaarijuotto

Tässä diplomityössä tutkitaan ultralujan rakenneteräksen kaarijuotolla valmistettujen liitosten väsymiskestävyyttä. Tutkittavat liitokset ovat kuormaa kantamattomia X-liitoksia. Tutkinnassa vertaillaan puhtaasti juottamalla valmistettua liitosta hitsauksen ja juoton kombinaatioliitokseen, jossa pohjapalkona toimivan hitsin rajaviivalle on juotettu lisäpalko. Kaarijuottoa esitellään yleisesti liittämismenetelmänä. Ultralujaa rakenneterästä esitellään yleisesti ja tarkastellaan sen metallurgista käyttäytymistä sekä juotettaessa, että hitsattaessa. Tutkimuksessa tehtiin kaikkiaan 21 väsytystestiä. Väsytystestit muodostuivat kolmesta eri koekappalesarjasta. Ensimmäisen ja toisen sarjan koekappaleet tehtiin juottamalla, eri lisäaineilla. 3. sarjassa pienat hitsattiin, jonka jälkeen hitsin rajaviivalle tehtiin juotto. Kappaleiden geometriat mitattiin ennen testejä, ja osasta kappaleista mitattiin jäännösjännitykset. Kappaleista otettiin hieitä, joista tehtiin kovuusmittaukset ja suoritettiin makro- ja mikrotason tarkastelua liitosprosessin lämmöntuonnin vaikutuksesta. Väsytyskokeiden perusteella kappaleille määritettiin nimelliset ja rakenteelliset väsymisluokat. Tuloksista piirrettiin S-N –käyrät. Liitoksista tehtiin FEA-mallit, joista määritettiin liitoksen rajaviivalle muodostuva jännitys ja 2. sarjan koekappaleiden laskennalliset kestoiät. 1. sarjan juotoksissa oli ongelmana juotoksen tarttuvuus teräksen pintaan. 2. sarjan koetulokset olivat kaikkein parhaita. 3. sarjan kombinaatioliitokset ylsivät kohtalaisiin väsymisluokkiin. 2. sarjan koetulosten perusteella kaarijuotossa on potentiaalia ultralujan rakenneteräksen liittämismenetelmänä. Jatkotutkimuksen tarve on kuitenkin laaja. Tämä työ osoitti, että kaarijuottaminen voi olla vaativa liittämisprosessi, sillä toimiakseen se vaatii varsin tarkat parametrit, ja lisäksi prosessi on melko herkkä olosuhdemuutoksille.

Real-time monitoring of laser scribing process utilizing high-speed camera

Currently, laser scribing is growing material processing method in the industry. Benefits of laser scribing technology are studied for example for improving an efficiency of solar cells. Due high-quality requirement of the fast scribing process, it is important to monitor the process in real time for detecting possible defects during the process. However, there is a lack of studies of laser scribing real time monitoring. Commonly used monitoring methods developed for other laser processes such a laser welding, are sufficient slow and existed applications cannot be implemented in fast laser scribing monitoring. The aim of this thesis is to find a method for laser scribing monitoring with a high-speed camera and evaluate reliability and performance of the developed monitoring system with experiments. The laser used in experiments is an IPG ytterbium pulsed fiber laser with 20 W maximum average power and Scan head optics used in the laser is Scanlab’s Hurryscan 14 II with an f100 tele-centric lens. The camera was connected to laser scanner using camera adapter to follow the laser process. A powerful fully programmable industrial computer was chosen for executing image processing and analysis. Algorithms for defect analysis, which are based on particle analysis, were developed using LabVIEW system design software. The performance of the algorithms was analyzed by analyzing a non-moving image from the scribing line with resolution 960x20 pixel. As a result, the maximum analysis speed was 560 frames per second. Reliability of the algorithm was evaluated by imaging scribing path with a variable number of defects 2000 mm/s when the laser was turned off and image analysis speed was 430 frames per second. The experiment was successful and as a result, the algorithms detected all defects from the scribing path. The final monitoring experiment was performed during a laser process. However, it was challenging to get active laser illumination work with the laser scanner due physical dimensions of the laser lens and the scanner. For reliable error detection, the illumination system is needed to be replaced.

Study of colossal magnetoresistance and pressure effects in La2/3Ca1/3MnO2 thin films /

The main purpose of this thesis is to study properties of La2/3Cai/3Mn03, both polycrystalline ceramics and thin films. This material has striking related electrical and magnetic properties. Thin films show colossal negative magnetoresistance (CMR) near transition from an insulating to a metallic state accompanied closely by transition from a paramagnetic to a ferromagnetic state. The double exchange mechanism (DE) and the Jahn-Teller deformations play an important role in CMR effect. Applied pressure has a very similar effect as does an applied magnetic field, except, at low temperatures (Tpulsed laser deposition was successfully developed. The films grown on (100) SrTiOs substrate are c-axis oriented and exhibit negative magnetoresistance Ap/p(H) of over 400% at 245°C and 4200% at 90 K.

Infrared spectroscopy of Mg-doped SrRuO3 thin films /

The reflectance of thin films of magnesium doped SrRu03(Mg-SR0) produced by pulsed laser deposition on SrTiOa (100) substrates has been measured at room temperature between 100 and 7500 cm~^. The films were chosen to have wide range of thickness, stoichiometry and electrical properties. As the films were very thin (less than 300 nm), and some were insulating the reflectance data shows structures due to both the film and the substrate. Hence, the data was analyzed using Kramers-Kronig constrained variational fitting (VDF) method to extract the real optical conductivity of the Mg-SRO films. Although the VDF technique is flexible enough to fit all features of the reflectance spectra, it seems that VDF could not eliminate the substrate's contribution from fllm conductivity results. Also the comparison of the two different programs implementing VDF fltting shows that this technique has a uniqueness problem. The optical properties are discussed in light of the measured structural and transport properties of the fllms which vary with preparation conditions and can be correlated with differences in stoichiometry. This investigation was aimed at checking the VDF technique and also getting answer to the question whether Mg^"*" substitutes in to Ru or Sr site. Analysis of our data suggests that Mg^+ goes to Ru site.