A new method of measuring the waveguide dispersion factor and the thermo-optic coefficient of long-period fiber gratings

Based on the Mach-Zehnder effect between the core mode and the cladding modes, the interference fringes are formed by a pair of cascaded long-period fiber gratings (CLPFGs). Theoretical analyses show that the spectral spacing and the wavelength of these fringes are functions of the waveguide dispersion factor gamma, which is a characterizing parameter to LPFG and with theoretical and applicational significance. By measuring the characteristics of the transmission spectra of CLPFGs, the absolute value of gamma can be obtained. At the same time, the thermo-optic coefficient of effective refractive index difference between core and cladding modes, p, can also be obtained by measured the temperature sensitivity of these fringes. In the experiments, \gamma\ and mu were measured by this method to be 0.874 and 4.08 x 10(-5) degreesC(-1), respectively, for LPFGs with period of 450 mum and with a HE14 resonant peak at 1554 nm. (C) 2004 Elsevier B.V. All rights reserved.

Optimization of the multiwavelength erbium-doped fiber laser in a unidirectional cavity without an isolator

A highly uniform multiwavelength erbium-doped fiber ring laser with an intracavity sine phase modulator is demonstrated. The flat output spectrum is achieved by optimizing the cavity structure, modulation amplitude, and frequency of the sine phase modulator. Fifteen lasing lines with wavelength spacing of 0.9 nm appear simultaneously and stably with power differences less than 2 dB and side-mode suppression ratio higher than 32 dB. In addition, the proposed cavity can support unidirectional operation without optical isolators. An output power difference of about 20 dB is realized between the counterclockwise and clockwise directions, which is almost independent of the pump power and lasing wavelengths. (c) 2005 Society of Photo-Optical Instrumentation Engineers.

Novel Mach-Zehnder interferometer structure for tunable optical interleaver

A novel optical interleaver scheme based on nested optical glass pairs is proposed. The assembly of pairs behaves as a cascaded Mach-Zehnder interferometer. The interleaver, with simple structure, low cost, and compact size, can be easily implemented with inexpensive material and mature preparation technology. Small channel spacing (<= 50 GHz), high isolation (<-30 dB), a wide, flat passband and stop band (> 2/11 period), and center-frequency tunability can be obtained simultaneously. An optimum design of a 50-GHz tunable interleaver based on this structure is given as an example. Its environmental temperature sensitivity and fabrication tolerance are also analyzed. (c) 2006 Society of Photo-Optical Instrumentation Engineers.

A study of T = 2 states in ^(12)B, ^(12)C, ^(20)F and ^(28)Al

The lowest T = 2 states have been identified and studied in the nuclei ¹²C, ¹²B, ²⁰F and and ²⁸Al. The first two of these were produced in the reactions ¹⁴C(p,t)¹²C and ¹⁴C (p,³He)¹²B, at 50.5 and 63.4 MeV incident proton energy respectively, at the Oak Ridge National Laboratory. The T = 2 states in ²⁰F and ²⁸Al were observed in (³He,p) reactions at 12-MeV incident energy, with the Caltech Tandem accelerator.

The results for the four nuclei studied are summarized below:

(1) ¹²C: the lowest T = 2 state was located at an excitation energy of 27595 ± 20 keV, and has a width less than 35 keV.

(2) ¹²B: the lowest T = 2 state was found at an excitation energy of 12710 ± 20 keV. The width was determined to be less than 54 keV and the spin and parity were confirmed to be 0⁺. A second ¹²B state (or doublet) was observed at an excitation energy of 14860 ± 30 keV with a width (if the group corresponds to a single state) of 226 ± 30 keV.

(3) ²⁰F: the lowest T = 2 state was observed at an excitation of 6513 ± 5 keV; the spin and parity were confirmed to be 0⁺. A second state, tentatively identified as T = 2 from the level spacing, was located at 8210 ± 6 keV.

(4) ²⁸Al: the lowest T = 2 state was identified at an excitation of 5997 ± 6 keV; the spin and parity were confirmed to be 0⁺. A second state at an excitation energy of 7491 ± 11 keV is tentatively identified as T = 2, with a corresponding (tentative) spin and parity assignment J^π = 2⁺.

The results of the present work and the other known masses of T = 2 states and nuclei for 8 ≤ A ≤ 28 are summarized, and massequation coefficients have been extracted for these multiplets. These coefficients were compared with those from T = 1 multiplets, and then used to predict the mass and stability of each of the unobserved members of the T = 2 multiplets.

Imaging the earth with ambient noise and earthquakes

In this thesis, I develop the velocity and structure models for the Los Angeles Basin and Southern Peru. The ultimate goal is to better understand the geological processes involved in the basin and subduction zone dynamics. The results are obtained from seismic interferometry using ambient noise and receiver functions using earthquake- generated waves. Some unusual signals specific to the local structures are also studied. The main findings are summarized as follows:

(1) Los Angeles Basin

The shear wave velocities range from 0.5 to 3.0 km/s in the sediments, with lateral gradients at the Newport-Inglewood, Compton-Los Alamitos, and Whittier Faults. The basin is a maximum of 8 km deep along the profile, and the Moho rises to a depth of 17 km under the basin. The basin has a stretch factor of 2.6 in the center decreasing to 1.3 at the edges, and is in approximate isostatic equilibrium. This "high-density" (~1 km spacing) "short-duration" (~1.5 month) experiment may serve as a prototype experiment that will allow basins to be covered by this type of low-cost survey.

(2) Peruvian subduction zone

Two prominent mid-crust structures are revealed in the 70 km thick crust under the Central Andes: a low-velocity zone interpreted as partially molten rocks beneath the Western Cordillera – Altiplano Plateau, and the underthrusting Brazilian Shield beneath the Eastern Cordillera. The low-velocity zone is oblique to the present trench, and possibly indicates the location of the volcanic arcs formed during the steepening of the Oligocene flat slab beneath the Altiplano Plateau.

The Nazca slab changes from normal dipping (~25 degrees) subduction in the southeast to flat subduction in the northwest of the study area. In the flat subduction regime, the slab subducts to ~100 km depth and then remains flat for ~300 km distance before it resumes a normal dipping geometry. The flat part closely follows the topography of the continental Moho above, indicating a strong suction force between the slab and the overriding plate. A high-velocity mantle wedge exists above the western half of the flat slab, which indicates the lack of melting and thus explains the cessation of the volcanism above. The velocity turns to normal values before the slab steepens again, indicating possible resumption of dehydration and ecologitization.

(3) Some unusual signals

Strong higher-mode Rayleigh waves due to the basin structure are observed in the periods less than 5 s. The particle motions provide a good test for distinguishing between the fundamental and higher mode. The precursor and coda waves relative to the interstation Rayleigh waves are observed, and modeled with a strong scatterer located in the active volcanic area in Southern Peru. In contrast with the usual receiver function analysis, multiples are extensively involved in this thesis. In the LA Basin, a good image is only from PpPs multiples, while in Peru, PpPp multiples contribute significantly to the final results.

Characteristics of 980/1550 nm WDM coupler based on planar curved waveguides

A wavelength division multiplexer (WDM) for 980/1550 nm based on planar curved waveguide coupler (CWC) is proposed. Compared with conventional parallel straight waveguide coupler (SWC), this structure has more flexibility with two variable parameters of bending radius R and minimum edge-to-edge spacing do, which are the two main parameters for the splitting ratio of coupler and decrease the complexity of device design and fabrication. Based on coupled mode theory (CMT) and waveguide theory, R and do of the WDM CWC are designed to be R = 13.28 m and d(0) = 4.39 mu m. The contrast ratio (CR) and insertion loss (IL) for 980 and 1550 nm are CR1 = 24.62 dB, CR2 = 24.56 dB and IL1 = 0.014 dB, IL2 = 0.015 dB, respectively. The 3D beam propagation method (BPM) is used to verify the validity of the design result. The influence of R and d(0) variations on the device performance is analyzed. For CR > 20 dB, the variation ranges of R and d(0) should be within -0.10 to +0.44 m and -0.05 to + 0.02 mu m, respectively. (c) 2006 Elsevier GmbH. All rights reserved.

调Q及连续掺Yb光纤激光器中的自锁模研究

在用半导体激光器抽运的单包层掺Yb调Q光纤激光器中观察到了清晰稳定的自锁模脉冲序列。脉冲包络形状为调Q脉冲。每个锁模脉冲的幅值由其在调Q脉冲中的相应位置决定。经过分析，认为自相位调制是调Q光纤激光器中产生锁模的主要原因。自相位调制的存在使得光脉冲的频谱被展宽，当这种展宽和腔的模式间隔相差不多时，腔内的模式便能相互作用，直到它们之间产生一个固定的相位关系。也即形成锁模。在此基础上。去掉声光晶体，并用两个光栅作为腔镜，实现了全光纤法布里-珀罗(F-P)腔锁模光纤激光器。改变腔结构，分别采用光栅和光纤反射圈作为

ICF中可调法布里-珀罗滤波器间距稳定度研究

在神光Ⅱ第9路ICF高功率激光装置中，采用可调法布里-珀罗（F-P）滤波器对幅度调制效应进行补偿，根据补偿装置的技术要求，提出-种应用nm量级精度的电容式位移传感器对可调F-P滤波器间距稳定度进行监控的系统，详细论述了监控系统的结构与工作原理。给出了电容式位移传感器的驱动电路及数据处理与控制软件的设计方案，并对电容式位移传感器的精度进行了标定。实验结果表明，该位移监控系统能够使可调F—P滤波器的间距稳定度保持在15nm／h以内，使幅度调制效应的调制深度优于4％。

Avaliação do cenário para utilização dos recursos florísticos nativos de restingas para inclusão socioeconômica em Caravelas, Bahia.

A conservação dos ecossistemas e dos recursos ambientais neles inclusos é uma condição básica e essencial para o desenvolvimento sustentado de uma dada região. A degradação faz com que a possibilidade dele retornar ao seu estado original seja ínfima pois, sua dinâmica de restauração não seria a mesma do que antes foi sua colonização. A recuperação de áreas degradadas é dificultada devido à complexidade estrutural dos ecossistemas, exemplo das restingas ambientes sujeitos as condições bastante adversas (altas temperaturas, períodos de seca, vento constante, alta salinidade e escassez de nutrientes), por isso demandam de alta tecnologia para o desenvolvimento e produção de mudas, além de alto custo associado. O objetivo deste estudo é a criação de uma proposta para uso socioeconômico das áreas degradadas por plantios de cocos, em formações vegetais de restinga, município de Caravelas, e criar um modelo para que essas áreas sejam mais produtivas economicamente, a médio e longo prazo, a partir da geração de trabalho e renda e, conseqüentemente, inclusão social voltada para o uso sustentável de espécies nativas de restinga, através do extrativismo, considerando-se o potencial e a vocação natural do ecossistema de restinga. Nesse contexto, as categorias de análise desta tese basearam-se nos conflitos e vulnerabilidade socioambiental, etnobotânica, fitofisionomias, bens e serviços associados, tecnologia social, desenvolvimento local, gestão costeira, sustentabilidade ambiental e democrática, produtos florestais não madeiráveis e inclusão social. Os procedimentos metodológicos utilizados neste estudo foram apresentados em cada capítulo desta tese, estando inserido em pesquisas qualitativas (técnicas de observação participante e análise do discurso coletivo) associada aos levantamentos bibliográficos (dados secundários) e as pesquisas quantitativas, por entrevistas semiestruturadas. Os resultados deste estudo subsidiaram a formação de uma rede interativa para implantação de empreendimentos sustentáveis no processo produtivo local, no que se refere à utilização de espécies nativas de restingas com reflorestamento de áreas degradadas por plantios de coco, para fins de geração de trabalho e renda com base no movimento de tecnologia social.

Investigação da microarquitetura óssea através de microtomografia 3D

A microtomografia computadorizada (uCT) é uma técnica de ensaio não destrutivo, frequentemente utilizada no estudo da estrutura interna de ossos, com uma resolução espacial da ordem de mícrons. Neste trabalho, seis pares de amostras ósseas (fêmur de rato) foram estudados através da uCT. Os ensaios foram conduzidos na presença ou não de filtros de alumínio (espessura de 0,25; 0,50 e 0,75 mm), utilizando-se três níveis de resolução (33,3; 15,0 e 9,5 um). Os parâmetros de arquitetura óssea BS (área óssea da amostra), BV (volume ósseo da amostra), TS (área superficial da amostra), TV (volume da amostra), BV/TV (razão entre o volume ósseo e o volume da amostra), BS/BV (razão entre a área óssea da amostra e o volume ósseo da amostra), Tb.N (densidade trabecular), Tb.Th (espaçamento entre as trabéculas), Tb.Sp (separação trabecular), conectividade e anisotropia foram determinados através das análises em duas (2D) e/ou três (3D) dimensões. A comparação entre os valores dos parâmetros obtidos através dessas análises foi realizada através do teste t pareado e da correlação de Pearson. Com base nos resultados, foi possível determinar a influência da resolução da imagem na qualidade dos parâmetros da arquitetura óssea obtidos através das análises 2D e/ou 3D. Os dados mostram que a presença de filtro de alumínio também afeta a qualidade desses parâmetros. Assim, os melhores resultados são obtidos com resolução máxima e filtro de alumínio com espessura de 0,25 ou 0,50 mm.

Super-resolution scanning laser microscopy with a third-order optical nonlinear thin film

In a configuration of optical far-field scanning microscopy, super-resolution achieved by inserting a third-order optical nonlinear thin film is demonstrated and analyzed in terms of the frequency response function. Without the thin film the microscopy is diffraction limited; thus, subwavelength features cannot be resolved. With the nonlinear thin film inserted, the resolution is dramatically improved and thus the microscopy resolves features significantly smaller than the smallest spacing allowed by the diffraction limit. A theoretical model is established and the device is analyzed for the frequency response function. The results show that the frequency response function exceeds the cutoff spatial frequency of the microscopy defined by the laser wavelength and the numerical aperture of the convergent lens. The main contribution to the improvement of the cutoff spatial frequency is from the phase change induced by the complex transmission of the nonlinear thin film. Experimental results are presented and are shown to be consistent with the results of theoretical simulations.

Argilas pilarizadas: uma tecnologia limpa na reação de isomerização do óxido de estireno

Neste trabalho, fracionou-se e tratou-se a argila Brasgel. Esta argila foi pilarizada em vários estágios de facionamento e/ou tratamento com 5 meq de Al / g de argila: (i) Al-PILC, a argila passou por todos os estágios de fracionamento e tratamento (ARG), (ii) Al-PILCFe, a argila não passou pela etapa de retirada de Fe livre (ARGFe) e (iii) Al-PILCFe/silte, a argila não passou pelas etapas de retirada de silte e Fe livre (ARGFE/silte). Em análise por DRX observou-se que as Al-PILCs apresentaram uma distância basal maior que as argilas de partida. A análise textural indicou que as argilas Al-PILCs e ARGs são materiais mesoporosos, com poros do tipo fenda estreita e do tipo fenda, respectivamente. Além disso, as Al-PILCs apresentaram área superficial razoavelmente maior que as ARGs correspondentes. Outras análises feitas nas argilas foram: teor de Si, Fe e Al; CTC; FTIR; TGA e TGD. As argilas Brasgel pilarizadas foram usadas como catalisador na reação de isomerização do óxido de estireno em hexano sob refluxo. A reação foi seletiva na formação de fenilacetaldeído. As argilas Al-PILCFe e Al-PILCFe/silte apresentaram melhor desempenho catalítico (100 % de conversão em 20 min de reação). Assim, as argilas Brasgel pilarizadas se apresentaram como uma Tecnologia Limpa na reação de isomerização do óxido de estireno ao fenilacetaldeído. Palavras-chave: Desenvolvimento Sustentável. Tecnologia Limpa. Química Verde. Argilas Pilarizadas. Isomerização de Epóxidos.

A new method of modeling cladding band structure of air-guiding photonic crystal fibers

Cladding band structure of air-guiding photonic crystal fibers with high air-filling fraction is calculated in terms of fiber shape variation. The fundamental photonic band gap dependence on structure parameters, air-filling fraction and spacing, is also investigated. The numerical results show that the band gap edges shift toward longer wavelength as the air-filling fraction is increased, whereas the relative band gap width increases linearly. For a fixed air-filling fraction, the band gap edges with respect to spacing keep constant. With this method, the simulation results agree well with the reported data. © 2007 Elsevier B.V. All rights reserved.

一种区域搜索获取平面光学元件光圈数的方法

提出一种获取平面光学元件光圈数的方法。通过确定一幅干涉条纹图像中三块测试区域及相应的搜索区域,寻找条纹弯曲量的平均值和相应条纹间距的平均值,根据测试区域对应的权重系数,得到被测平面光学元件光圈数的最佳估计值。通过测量标准光圈并比较目视判读结果,得到最大相对误差为5%。实验结果表明,该方法提高了处理干涉条纹图像的适应性,并可替代人工目视判读干涉条纹图像。

Band structure of photonic crystal fibers with silica rings in triangular lattice

The characteristics of the cladding band structure of air-core photonic crystal fibers with silica rings in triangular lattice are investigated by using a standard plane wave method. The numerical results show that light can be localized in the air core by the photonic band gaps of the fiber. By increasing the air-filling fraction, the band gap edges of the low frequency photonic band gaps shift to shorter wavelength.. whereas the band gap width decreases linearly. In order to make a specified light fall in the low frequency band gaps of the fiber, the interplay of the silica ring spacing and the air-filling fraction is also analyzed. It shows that the silica ring spacing increases monotonously when the air-filling fraction is increased, and the spacing range increases exponentially. This type fiber might have potential in infrared light transmission. (c) 2006 Elsevier B.V. All rights reserved.