Improving the performance of model-order selection criteria by partial-model selection search

The traditional searching method for model-order selection in linear regression is a nested full-parameters-set searching procedure over the desired orders, which we call full-model order selection. On the other hand, a method for model-selection searches for the best sub-model within each order. In this paper, we propose using the model-selection searching method for model-order selection, which we call partial-model order selection. We show by simulations that the proposed searching method gives better accuracies than the traditional one, especially for low signal-to-noise ratios over a wide range of model-order selection criteria (both information theoretic based and bootstrap-based). Also, we show that for some models the performance of the bootstrap-based criterion improves significantly by using the proposed partial-model selection searching method. Index Terms— Model order estimation, model selection, information theoretic criteria, bootstrap 1. INTRODUCTION Several model-order selection criteria can be applied to find the optimal order. Some of the more commonly used information theoretic-based procedures include Akaike’s information criterion (AIC) [1], corrected Akaike (AICc) [2], minimum description length (MDL) [3], normalized maximum likelihood (NML) [4], Hannan-Quinn criterion (HQC) [5], conditional model-order estimation (CME) [6], and the efficient detection criterion (EDC) [7]. From a practical point of view, it is difficult to decide which model order selection criterion to use. Many of them perform reasonably well when the signal-to-noise ratio (SNR) is high. The discrepancies in their performance, however, become more evident when the SNR is low. In those situations, the performance of the given technique is not only determined by the model structure (say a polynomial trend versus a Fourier series) but, more importantly, by the relative values of the parameters within the model. This makes the comparison between the model-order selection algorithms difficult as within the same model with a given order one could find an example for which one of the methods performs favourably well or fails [6, 8]. Our aim is to improve the performance of the model order selection criteria in cases where the SNR is low by considering a model-selection searching procedure that takes into account not only the full-model order search but also a partial model order search within the given model order. Understandably, the improvement in the performance of the model order estimation is at the expense of additional computational complexity.

Customers behaving badly : a state of the art review, research agenda and implications for practitioners

The purpose of this paper is to highlight important issues in the study of dysfunctional customer behavior and to provide a research agenda to inspire, guide, and enthuse. Through a critical evaluation of existing research, the aim is to highlight key issues and to present potentially worthy avenues for future study.

Lumia : art/light/motion

Lumia: art/light/motion is an exciting new media exhibition presented by State Library of Queensland in partnership with Queensland-based Kuuki collective artists Priscilla Bracks and Gavin Sade. The exhibition explored contemporary life and encourages thought about the future through an extraordinary collection of hand-crafted and interactive electronic creatures and installations. The beautifully crafted new media artworks in Lumia: art/light/motion combine the bespoke with art and technology to create strange but intriguing objects. Lumia invited audiences to play, learn and then ponder the way we live and the environmental and social implications of our choices.

Stripping Sight Bare : Alison Jones’ ‘Portraits by Proxy’

In this paper I analyse UK artist Alison Jones’ sonic interventions Portrait of the Artist by Proxy (2008), Voyeurism by Proxy (2008) and Art, Lies and Audio Tapes (2009). In Portrait of the Artist by Proxy, Jones – who, due to deteriorating vision, has not seen her reflection in a mirror in years – asks and trusts participants to audio-describe her own image back to her. In Voyeurism by Proxy, Jones asks participants to audio-describe erotic drawings by Gustav Klimt. In Art, Lies and Audio Tapes, Jones asks participants to audio-describe other artworks, such as W.F. Yeames’ And When Did You Last see Your Father?. In these portraits by proxy, Jones opens her image, and other images, to interpretation. In doing so, Jones draws attention to the way sight is privileged as a mode of access to fixed, fundamental truths in Western culture – a mode assumed to be untainted by filters that skew perception of the object. “In a culture where vision is by far the dominant sense,” Jones says, “and as a visual artist with a visual impairment, I am reliant on audio-description …Inevitably, there are limitations imposed by language, time and the interpreter’s background knowledge of the subject viewed, as well as their personal bias of what is deemed important to impart in their description” . In these works, Jones strips these background knowledges, biases and assumptions bare. She reveals different perceptions, as well as tendencies or censor, edit or exaggerate descriptions. In this paper, I investigate how, by revealing unconscious biases, Jones’ works renders herself and her participants vulnerable to a change of perception. I also examine how Jones’ later editing of the audio-descriptions allows her to show the instabilities of sight, and, in Portrait of the Artist by Proxy, to reclaim authorship of her own image.

Nothing if not a performance of substance [REVIEW]

This is an oddly engaging piece of theatre by American playwright Will Eno. It starts with a deceptively simple, straightforward and familiar theatrical premise. A solitary character on a big, black stage, bare but for a single table and a single chair, tells us a story. Thom is a man we know nothing about. Nothing about the suit he wears, the stage he inhabits or the story he tells locates in him time, space, or a specific social milieu.

Throwing frame and performance of elite male seated shot-putters

Seated shot-putters rely on a customized assistive device called a throwing frame. Currently, the construction of each individual throwing frame is mainly driven by an empirical approach. One way to refine the conception is to improve the basic understanding of performance of seated shot-putters. The relationship between performance and throwing technique has been well described. Remarkably, the relationship between performance and throwing frame characteristics has received limited attention. The primary objective of this study was to present a cataloguing of characteristics of throwing frames used by seated shot-putters. This cataloguing consisted of defining and grouping 26 characteristics into three main categories (i.e., whole body, foot and upper limb specific characteristics) and seven sub-categories. The secondary objective of this study was to provide raw characterisations of the throwing frames for a group of athletes who participated in a world-class event. The characterisation consisted of describing the characteristics of each throwing frame. Potential relationships between characteristics, performance and classification were also identified. The cataloguing was achieved using a 6-step heuristic approach, involving expert opinions and the analysis of 215 attempts produced by 55 male athletes during the 2006 IPC Athletics World Championships. The distribution of samples across characteristics suggested a relevant level of comprehensiveness for the proposed cataloguing. The raw data, the profile of best athletes and the frequency of characteristics provided key benchmark information for construction of a throwing frame as well as coaching, classification and officiating. Analysis of data sets relating to characteristics, performance and classification were inconclusive.

Contribution to the Pamela Croft Sandhills Studio Consultancy for the Yeppoon Public Art Project in 2000

A small collection of creative works developed to acompany some of the artistic images developed by visual artist Dr Pamela Croft for the Yeppoon Public Art Project in 2000.

Performance analysis of hybrid liquid desiccant solar cooling system

This thesis investigates the coefficient of performance (COP) of a hybrid liquid desiccant solar cooling system. This hybrid cooling system includes three sections: 1) conventional air-conditioning section; 2) liquid desiccant dehumidification section and 3) air mixture section. The air handling unit (AHU) with mixture variable air volume design is included in the hybrid cooling system to control humidity. In the combined system, the air is first dehumidified in the dehumidifier and then mixed with ambient air by AHU before entering the evaporator. Experiments using lithium chloride as the liquid desiccant have been carried out for the performance evaluation of the dehumidifier and regenerator. Based on the air mixture (AHU) design, the electrical coefficient of performance (ECOP), thermal coefficient of performance (TCOP) and whole system coefficient of performance (COPsys) models used in the hybrid liquid desiccant solar cooing system were developed to evaluate this system performance. These mathematical models can be used to describe the coefficient of performance trend under different ambient conditions, while also providing a convenient comparison with conventional air conditioning systems. These models provide good explanations about the relationship between the performance predictions of models and ambient air parameters. The simulation results have revealed the coefficient of performance in hybrid liquid desiccant solar cooling systems substantially depends on ambient air and dehumidifier parameters. Also, the liquid desiccant experiments prove that the latent component of the total cooling load requirements can be easily fulfilled by using the liquid desiccant dehumidifier. While cooling requirements can be met, the liquid desiccant system is however still subject to the hysteresis problems.

Retracing the Roots and Ideals of Confucian Principles of Governance: the Art of Regulating Governance without Legal Rules in Chinese Societies

Confucius was and still is one of the most eminent Chinese philosophers. Such is the importance of Confucius’s teachings; it had influenced all aspects of social life in Chinese societies. In the post-Enron, post-Worldcom, and post-Global Financial Crisis era there are raising doubts in the mantra of the so-called conventional wisdom about law and economic order. Whilst many recent publications offered solutions to those problems like advocating for more laws, rules or reforms in regulatory institutions to enhance the regulation of corporate governance. What Confucius advocated was a non-legal, social mode of regulation based on moral ideals that should be embedded into the minds of every person. Whilst this is an ancient concept from primitive societies, its relevance and merits could be seen in modern Chinese societies like Hong Kong. In essence, Confucian principles of governance build on relational and paternalistic order based on moral ideals.

Is a mango just a mango? Testing within-fruit oviposition site choice and larval performance of a highly polyphagous fruit fly

For fruit flies, fully ripe fruit is preferred for adult oviposition and is superior for offspring performance over unripe or ripening fruit. Because not all parts of a single fruit ripen simultaneously, the opportunity exists for adult fruit flies to selectively choose riper parts of a fruit for oviposition and such selection, if it occurs, could positively influence offspring performance. Such fine scale host variation is rarely considered in fruit fly ecology, however, especially for polyphagous species which are, by definition, considered to be generalist host users. Here we study the adult oviposition preference/larval performance relationship of the Oriental fruit fly, Bactrocera dorsalis (Hendel) (Diptera: Tephritidae), a highly polyphagous pest species, at the “within-fruit” level to see if such a host use pattern occurs. We recorded the number of oviposition attempts that female flies made into three fruit portions (top, middle and bottom), and larval behavior and development within different fruit portions for ripening (color change) and fully-ripe mango, Mangifera indica L. (Anacardiaceae). Results indicate that female B. dorsalis do not oviposit uniformly across a mango fruit, but lay most often in the top (i.e., stalk end) of fruit and least in the bottom portion, regardless of ripening stage. There was no evidence of larval feeding site preference or performance (development time, pupal weight, percent pupation) being influenced by fruit portion, within or across the fruit ripening stages. There was, however, a very significant effect on adult emergence rate from pupae, with adult emergence rate from pupae from the bottom of ripening mango being approximately only 50% of the adult emergence rate from the top of ripening fruit, or from both the top and bottom of fully-ripe fruit. Differences in mechanical (firmness) and chemical (total soluble solids, titratable acidity, total non-structural carbohydrates) traits between different fruit portions were correlated with adult fruit utilisation. Our results support a positive adult preference/offspring performance relationship at within-fruit level for B. dorsalis. The fine level of host discrimination exhibited by B. dorsalis is at odds with the general perception that, as a polyphagous herbivore, the fly should show very little discrimination in its host use behavior.

Last shall be first : a field study of biases in sequential performance evaluation on the Idol series

When performances are evaluated they are very often presented in a sequential order. Previous research suggests that the sequential presentation of alternatives may induce systematic biases in the way performances are evaluated. Such a phenomenon has been scarcely studied in economics. Using a large dataset of performance evaluation in the Idol series (N=1522), this paper presents new evidence about the systematic biases in sequential evaluation of performances and the psychological phenomena at the origin of these biases.

Integrating the resource-based view and transaction cost economics in immigrant business performance

This paper presents a new integrated framework that integrates the resource-based view and transaction cost economics to explain the phenomenon of immigrant entrepreneurship. We extend the existing literature on immigrant entrepreneurship by identifying different types of ethnic network resources and demonstrating how these resources interact with transaction costs in the context of Chinese immigrants. Thus, our study contributes to the literature by providing a theoretical framework which identifies mechanisms immigrant entrepreneurs use to strategically deploy resources to minimize costs and maximize performance outcomes.

Assessment of commercial network RTK user positioning performance over long inter-station distances

The paper provides an assessment of the performance of commercial Real Time Kinematic (RTK) systems over longer than recommended inter-station distances. The experiments were set up to test and analyse solutions from the i-MAX, MAX and VRS systems being operated with three triangle shaped network cells, each having an average inter-station distance of 69km, 118km and 166km. The performance characteristics appraised included initialization success rate, initialization time, RTK position accuracy and availability, ambiguity resolution risk and RTK integrity risk in order to provide a wider perspective of the performance of the testing systems. ----- ----- The results showed that the performances of all network RTK solutions assessed were affected by the increase in the inter-station distances to similar degrees. The MAX solution achieved the highest initialization success rate of 96.6% on average, albeit with a longer initialisation time. Two VRS approaches achieved lower initialization success rate of 80% over the large triangle. In terms of RTK positioning accuracy after successful initialisation, the results indicated a good agreement between the actual error growth in both horizontal and vertical components and the accuracy specified in the RMS and part per million (ppm) values by the manufacturers. ----- ----- Additionally, the VRS approaches performed better than the MAX and i-MAX when being tested under the standard triangle network with a mean inter-station distance of 69km. However as the inter-station distance increases, the network RTK software may fail to generate VRS correction and then may turn to operate in the nearest single-base RTK (or RAW) mode. The position uncertainty reached beyond 2 meters occasionally, showing that the RTK rover software was using an incorrect ambiguity fixed solution to estimate the rover position rather than automatically dropping back to using an ambiguity float solution. Results identified that the risk of incorrectly resolving ambiguities reached 18%, 20%, 13% and 25% for i-MAX, MAX, Leica VRS and Trimble VRS respectively when operating over the large triangle network. Additionally, the Coordinate Quality indicator values given by the Leica GX1230 GG rover receiver tended to be over-optimistic and not functioning well with the identification of incorrectly fixed integer ambiguity solutions. In summary, this independent assessment has identified some problems and failures that can occur in all of the systems tested, especially when being pushed beyond the recommended limits. While such failures are expected, they can offer useful insights into where users should be wary and how manufacturers might improve their products. The results also demonstrate that integrity monitoring of RTK solutions is indeed necessary for precision applications, thus deserving serious attention from researchers and system providers.

Measuring the performance of Customs Information Systems (CIS) in Malaysia

In the scope of this study, ‘performance measurement’ includes the collection and presentation of relevant information that reflects progress in achieving organisational strategic aims and meeting the needs of stakeholders such as merchants, importers, exporters and other clients. Evidence shows that utilising information technology (IT) in customs matters supports import and export practices and ensures that supply chain management flows seamlessly. This paper briefly reviews some practical techniques for measuring performance. Its aim is to recommend a model for measuring the performance of information systems (IS): in this case, the Customs Information System (CIS) used by the Royal Malaysian Customs Department (RMCD).The study evaluates the effectiveness of CIS implementation measures in Malaysia from an IT perspective. A model based on IS theories will be used to assess the impact of CIS. The findings of this study recommend measures for evaluating the performance of CIS and its organisational impacts in Malaysia. It is also hoped that the results of the study will assist other Customs administrations evaluate the performance of their information systems.

Adhesion and dispersion of salmeterol xinofoate from lactose interactive mixtures for inhalation - can surface roughness of carriers determine performance

The objective was to understand the influence of the surface roughness of lactose carriers on the adhesion and dispersion of salmeterol xinafoate (SX) from interactive mixtures. The surface roughness of lactose carriers was determined by confocal microscopy. Particle images and adhesion forces between SX and lactose particles were determined by Atomic Force Microscopy. The dispersion of SX (2.5%) from interactive mixtures with lactose was determined using a twin-stage impinger (TSI) with a Rotahaler® at an airflow rate of 60L/min. SX was analysed using a validated HPLC assay. The RMS Rq of lactose carriers ranged from 0.93-2.84μm, the Fine Particle Fraction (FPF) of SX ranged between 4 and 24 percent and average adhesion force between a SX and lactose particles ranged between 49 and 134 nN. No direct correlation was observed between the RMS Rq of lactose carriers and either the FPF of SX for the interactive mixtures or the adhesion force of a SX on the lactose particles; however, the presence of fine lactose associated with the carrier surface increased the FPF of SX. Dispersion through direct SX detachment from the carrier surface was not consistent with the poor correlations described and was more likely to occur through complex particulate interactions involving fine lactose.