Synthesis, physical and magnetic properties of BaFe12O19/P(VDF-TrFE) multifunctional composites

Composite films with filler microparticles of Barium ferrite dispersed within P(VDF-TrFE) as polymeric matrix have been prepared by solvent evaporation. The lowest BaFO content of 1% wt acts as a small defect within the polymeric matrix, reducing the values of the dielectric and mechanical properties of the pure P(VDF-TrFE). For filler contents up to a 20%, the BaFO filler reinforces the matrix and measured properties increase their values. This trend is not followed by the electrical conductivity. We extended the study to fibers composed by BaFe12O19 microparticles in a PVDF matrix. Due to the big size of BaFO particles (1 micron in diameter), proper fabrication of the fiber shaped composites has not been achieved. We found that true BaFO content are always lower than nominal ones. Results are discussed in terms of the influence of size and morphology of the BaFO particles on the initial properties of the polymeric matrix.

Structural, mechanical and piezoelectric properties of polycrystalline AlN films sputtered on titanium bottom electrodes

Polycrystalline AlN coatings deposited on Ti-electrodes films were sputtered by using nitrogen both as reactive gas and sputtering gas, in order to obtain high purity coatings with appropriate properties to be further integrated into wear resistance coatings as a piezoelectric monitoring wear sensor. The chemical composition, the structure and the morphology of the films were investigated by X-ray diffraction, X-ray photoelectron spectroscopy, scanning electron microscopy and atomic force microscopy techniques. These measurements show the formation of highly (101), (102) and (103) oriented AlN films with good piezoelectric and mechanical properties suitable for applications in electronic devices. Through the use of lower nitrogen flow a densification of the AlN coating occurs in the microstructure, with an improvement of the crystallinity along with the increase of the hardness. Thermal stability of aluminum nitride coatings at high temperature was also examined. It was found an improvement of the piezoelectric properties of the highly (10x) oriented AlN films which became c-axis (002) oriented after annealing. The mechanical behavior after heat treatment shows an important enhancement of the surface hardness and Young’s modulus, which decrease rapidly with the increase of the indentation depth until approach constant values close to the substrate properties after annealing. Thus, thermal annealing energy promotes not only the rearrangement of Al–N network, but also the occurrence of a nitriding process of unsaturated Al atoms which cause a surface hardening of the film.

Antibacterial properties of fibrous stents coated with silver oxide nanocoatings

Stents are rigid and perforated tubular structures, which are inserted into blood vessels in order to prevent or inhibit the constriction of blood flow, restoring the normal blood flow, when blood vessels are clogged, being used in 70% of angioplasties. These medical devices assume great importance in the treatment of cardiovascular diseases (CVD) which are the leading cause of death worldwide. In the European Union CVD account for 40% of deaths and assume an estimated annual cost of 196 billion euros[1]. Stents must possess certain requirements, in order to, adequately, perform its function, such as biocompatibility (so that its use does not c ause damage on the health of its user), mechanical strength, radiopacity (so that it is easy to view), longitudinal flexibility, ease of handling, corrosion resistance and having high strength and high radial expansion ability to recover. Stents can be made of different materials, but metals, particularly stainless steel, are the most common. However, metallic stents present several dRawbacks such as corrosion and restenosis, leading to health complications for the patient, or even death. In order to minimize these disadvantages, new materials, like fibrous materials, have been used [2]. Monofilaments present high potential for stents development because, in addition to its biocompatibility, these materials allow the application of various surface treatments, such as antibacterial coatings. Furthermore, monofilament exhibit excellent mechanical properties, like greater stiffness and good results when subjected to compression, tensile and bending forces, since these forces will be directly supported by the monofilament [3]. To minimize the reaction of the human body and Limit the adhesion of microorganisms to the stent surface, some coatings have been developed, including the use of novel metals with antimicrobial properties, like silver. The main objective of this study was the development of fibrous stents, incorporation of silver oxide nanocoating. For the development of the stent, polyester monofilaments with 0.27mm of diameter were used in braiding technology, with a mandrel diameter of 6mm and a braiding angle of 35⁰. The mechanical behaviour of the stent were evaluated by mechanical testing under longitudinal and radial compression, bending. The results of compressive strength tests are according with value from literature: 1.13 to 2.9 N for radial compression and 0. 16-5.28N to longitudinal compression. From literature is also possible to verify that stents must present 75% of unchanged diameter during the bending test and must possess a porosity between 70% and 80% [4]. The produced polyester stent presents values of 1.29N for radial compression, 0.23N for longitudinal compression, 80% of porosity and 85.5% of unchanged diameter, during bending tests. For the antibacterial functionalization, silver oxide nanocoatings were prepared, through reactive magnetron g, with an Ag target in an Ar +O2 atmosphere. In order to evaluate the nanostructure and morphology of the coatings, d ifferent technique s like X-ray diffraction (XRD), scanning electron microscopy (SEM) and and X- ray photoelectron spectroscopy (XPS were used. From the analyses of XRD it is possible to verify that the peaks corresponds to planes of Ag2 O and MATERIAIS 2015 Porto, 21-23 June, 2015 characterize a cubic phase. The presence of Ag2 O is corroborated by XPS spectrum, where it is possible to observe silver, not only, in oxide state, but a lso in mettalic state, and it is possible to verify the presence of silver clusters, confirmed by SEM analysis. Films’ roughness and topography, parameters influencing the wettability of the surface and microorganism adhesion, were measured by Atomic Force Microscopy (AFM), and it was observed that the roughness is very low (under 10 nm). Coatings’ hydrophobicity and surface tension parameters were determined by contact angle measurement, and it was verified the hydrophobic behavior of the coatings. For antibacterial tests were used Staphylococcus epidermidis strain (IE186) and Staphylococcus aureus(ATCC 6538), and halo inhibition zone tests were realized. Ag+release rates were studied by means of inductively coupled plasma mass spectrometry (ICP -MS). The obtained results suggest that silver oxide coatings do not modify significantly surface properties of the substrate, like hydrophobicity and roughness, and present antimicrobial properties for both bacteria used.

Thin films composed of gold nanoparticles dispersed in a dielectric matrix: the influence of the host matrix on the optical and mechanical responses

Gold nanoparticles were dispersed in two different dielectric matrices, TiO2 and Al2O3, using magnetron sputtering and a post-deposition annealing treatment. The main goal of the present work was to study how the two different host dielectric matrices, and the resulting microstructure evolution (including both the nanoparticles and the host matrix itself) promoted by thermal annealing, influenced the physical properties of the films. In particular, the structure and morphology of the nanocomposites were correlated with the optical response of the thin films, namely their localized surface plasmon resonance (LSPR) characteristics. Furthermore, and in order to scan the future application of the two thin film system in different types of sensors (namely biological ones), their functional behaviour (hardness and Young's modulus change) was also evaluated. Despite the similar Au concentrations in both matrices (~ 11 at.%), very different microstructural features were observed, which were found to depend strongly on the annealing temperature. The main structural differences included: (i) the early crystallization of the TiO2 host matrix, while the Al2O3 one remained amorphous up to 800 °C; (ii) different grain size evolution behaviours with the annealing temperature, namely an almost linear increase for the Au:TiO2 system (from 3 to 11 nm), and the approximately constant values observed in the Au:Al2O3 system (4–5 nm). The results from the nanoparticle size distributions were also found to be quite sensitive to the surrounding matrix, suggesting different mechanisms for the nanoparticle growth (particle migration and coalescence dominating in TiO2 and Ostwald ripening in Al2O3). These different clustering behaviours induced different transmittance-LSPR responses and a good mechanical stability, which opens the possibility for future use of these nanocomposite thin film systems in some envisaged applications (e.g. LSPR-biosensors).

Flowering levels, harvest season and yields of cupuassu (Theobroma grandiflorum)

Cupuassu (Theobroma grandiflorum), a specie native to Amazonia, has been planted commercially in Brazil to satisfy the demand for the flavorful juice obtained from the pulp around its seeds. The trees are notorious for low and irregular fruit production. Data gathered over two seasons from trees in a germplasm collection in Pará, Brazil, showed that some of them fruited more regularly than others. Differences in fruit production correlated to differences in flower production. Tree-to-tree variation in flower production, fruit production, and consistency of both over time suggest considerable scope for improving yields by selection. Hand pollinations resulted in a much higher frequency of fruit set than open pollinations, indicating that lack of effective pollination is also a reason for low yield. However, attempts to increase the level of effective pollination are handicapped by low knowledge about the pollinators of cupuassu and their behavior.

Biological behaviour of thin films consisting of Au nanoparticles dispersed in a TiO2 dielectric matrix

In this work it was studied the possible use of thin films, composed of Au nanoparticles (NPs) embedded in a TiO2 matrix, in biological applications, by evaluating their interaction with a well-known protein, Bovine Serum Albumin (BSA), as well as with microbial cells (Candida albicans). The films were produced by one-step reactive DC magnetron sputtering followed by heat-treatment. The samples revealed a composition of 8.3 at.% of Au and a stoichiometric TiO2 matrix. The annealing promoted grain size increase of the Au NPs from 3 nm (at 300 °C) to 7 nm (at 500 °C) and a progressive crystallization of the TiO2 matrix to anatase. A broad localized surface plasmon resonance (LSPR) absorption band (λ = 580–720 nm) was clearly observed in the sample annealed at 500 °C, being less intense at 300 °C. The biological tests indicated that the BSA adhesion is dependent on surface nanostructure morphology, which in turn depends on the annealing temperature that changed the roughness and wettability of the films. The Au:TiO2 thin films also induced a significant change of the microbial cell membrane integrity, and ultimately the cell viability, which in turn affected the adhesion on its surface. The microstructural changes (structure, grain size and surface morphology) of the Au:TiO2 films promoted by heat-treatment shaped the amount of BSA adhered and affected cell viability.

Production and characterization of ZrCN-Ag coatings deposited by mganetron sputtering

Tese de Doutoramento (Programa doutoral em Engenharia de Materiais)

Analysis of the effects of the continuous electrode paste band on precordial leads of the electrocardiogram

OBJECTIVE - To determine if the application of a continuous electrode paste band on precordial leads results in alteration of the electrocardiographic tracing as compared with an adequate amount of electrode paste, and if the former condition does not cause uniform morphologies from V1 to V6. METHODS - The amplitude and morphology of the electrocardiographic waves on the precordial leads in electrocardiographic tracings, which were performed with standard (control group) or excessive (continuous band) application of the electrode paste, were compared. RESULTS - None of the 106 patients studied showed uniformity of the QRS morphology from V1 to V6. The eletrocardiographic alterations identified in the tracings performed with a continuous electrode paste band that showed statistical significance in relation to the control group were the following: inversion of the P wave in V1; inversion of the T wave in V1, V2, and V3; appearance of R' waves in V1 and V2; disappearance of S waves in V1; appearance of S waves in V5 and V6; alterations in the amplitude of almost all waves, in all leads. CONCLUSION - Application of a continuous electrode paste band in the precordial leads may cause significant alterations in the electrocardiographic tracing obtained.

Effects of ethephon and urea on ripening of fruits and leaf abscission of coffee (Coffea arábica L.)

A field experiment was carried out to investigate the effects of ethephon and urea on ripening of fruits and leaf abscission of coffee plant. Ethephon (2-chloroethane phosphonic acid) sprays were applied to green Coffea arábica berries 26 days before counting date in concentrations of 0.5 and 0.25 ml/1 from Ethrel (240 a.i./l). The chemical accelerated the onset of fruit ripening at both concentrations. The efficacy of ethephon was increased adding urea. Ethephon 0.5 ml/1 promoted abscission of leaves and low concentration reduced shedding of leaves. The treatments did not affect the growth and production on the next harvest.

Organization of the cysts in bee (Hymenoptera, Apidae) testis: number of spermatozoa per cyst

The morphology of the cyst cells in Apis mellifera Linné, 1758, Scaptotrigona postica Latreille, 1804, and Melipona bicolor bicolor Lepeletier, 1836 testis, as well as the average number of spermatic cells are reported. The data indicates a supporting and nourrishing role of the cyst cells to the developing cystocytes. The counts of immature spermatozoa in the cysts show an average of 202.8 ± 21.2 spermatozoa for A. mellifera, 117.4 ± 8.68 for S. postica and 88.8 ± 15.57 for M. bicolor, which predict the occurrence of 8 mitotic cycles in the cystocytes of A. mellifera and 7 in the meliponines, considering that only one spermatozoom originates of each final spermatogonium.

New species of Thaumastus from Lagoa Santa region, Minas Gerais State, Brazil (Mollusca, Gastropoda, Pulmonata, Bulimuloidea)

A new species of Thaumastus (Thaumastus) Martens, 1860, from Minas Gerais State, Brazil, is described and illustrated, based on the morphology of the shell, jaw, radula and soft parts.

Revision of Taurocerus (Heteroptera, Pentatomidae, Pentatomini)

Taurocerus Amyot & Serville, 1843 is revised based on morphology of male and female genitalia. Four species are recognized: T. edessoides (Spinola, 1837), T. achiles Stål, 1862, T. abruptus (Walker, 1867), and T. amazonensis sp. nov. Illustrations of male and female genitalia and a key for the species are provided.

Microspines in the pylorus of Pseudonannolene tricolor and Rhinocricus padbergi (Arthropoda, Diplopoda)

The aim of this paper is to report the morphology and distribution of microspines in diplopods pylorus, as these are important structures present along the alimentary tract of arthropods. The morphology of the internal surface of the pylorus of Pseudonannolene tricolor Brolemann, 1901 and Rhinocricus padbergi Verhoeff, 1938 was analyzed by SEM. Pseudonannolene tricolor presents two morphologically distinct pyloric regions: anterior and posterior. The first region is characterized by the presence of thin microspines that increase in number and size towards the posterior portion; the second region presents smaller and triangular-shaped microspines distributed throughout small plates. The pylorus of R. padbergi does not present differentiated regions; the anterior portion is characterized by microspines grouped in plates that decrease in number and increase in size towards the ileum.

Histology of the liver of Oligosarcus jenynsii (Ostariophysi, Characidae) from Los Padres Lake, Argentina

The liver is an organ notable for its sensitivity to a great variety of environmental factors. It is composed of a parenchyma divided into irregular lobules by the exocrine pancreas or hepatopancreas; the pancreatic cells are arranged around a branch of the portal vein. The hepatocytes are radially arranged in cords around a central sinusoid. The liver histomorphology and the organization of exocrine pancreatic tissue of O. jenynsii (Günther, 1864) is similar to the acinar morphology of many teleosts, including freshwater and marine species. The aim of the present work was to carry out the histological analysis of the liver of Oligosarcus jenynsii, one of the most common species inhabiting Los Padres Lake (Buenos Aires Province, Argentina).

Gonad development in females of fiddler crab Uca rapax (Crustacea, Brachyura, Ocypodidae) using macro and microscopic techniques

The morphology of the ovaries in Uca rapax (Smith, 1870) was described based on macroscopic and microscopic analysis. Females were collected in Itamambuca mangrove, Ubatuba, state of São Paulo, Brazil. In the laboratory, 18 females had their ovaries removed and prepared for histology. Each gonad developmental stage was previously determined based on external and macroscopic morphology and afterwards each stage was microscopically described. The ovaries of U. rapax showed a pronounced macroscopic differentiation in size and coloration with the maturation of the gonad, with six ovarian developmental stages: immature, rudimentary, developing, developed, advanced and spent. During the vitellogenesis, the amount of oocytes in secondary stage increases in the ovary, resulting in a change in coloration of the gonad. Oogonias, primary oocytes, secondary oocytes and follicular cells were histologically described and measured. In female’s ovaries of U. rapax the modifications observed in the oocytes during the process of gonad maturation are similar to descriptions of gonads of other females of brachyuran crustaceans. The similarities are specially found in the morphological changes in the reproductive cells, and also in the presence and arrange of follicle cells during the process of ovary maturation. When external morphological characteristics of the gonads were compared to histological descriptions, it was possible to observe modifications that characterize the process in different developmental stages throughout the ovarian cycle and, consequently, the macroscopic classification of gonad stages agree with the modifications of the reproductive cells.