Experimental investigation on bubble coalescence under nonuniform temperature distribution in reduced gravity

Results on bubble coalescences from the space experiment of thermocapillary bubble migration conducted on board the Chinese 22nd recoverable satellite are presented in this paper. Some coalescences of large spherical bubbles under microgravity are observed through bubbles staying at the upper side of the test cell. The data of bubble coalescence time are recorded and compared with theoretical predictions, which is based on a theory to describe the tendency of coalescence connected to chemical potential difference. It is implied that the theory is applicable for the experimental data of bubble coalescence. Moreover, the angle between the line of two bubble centers and temperature gradient falled mostly in the range 20 degrees-40 degrees. (C) 2007 Elsevier Inc. All rights reserved.

Drop migration of middle Reynolds number in a vertical temperature gradient

The experimental investigation of the thermocapillary drop migration in a vertical temperature gradient uns performed on ground. Silicon oil and pure soybean oil were used as experimental medium in drops and as continuous phases, respectively, in the present experiment. The drop migration, under the combined effects of buoyancy: and thermocapillarity, was studied for middle Reynolds numbers in order of magnitude O(10(1)). The drop migration velocities depending on drop diameters were obtained. The present experimental results show relatively small migration velocity in comparison with the one suggested by Young et nl. for linear theory of small Reynolds number. An example of flow patterns inside the drop was observed by PIV method.

The motion of solid particles in a liquid with vertical temperature-gradient

A ground-experiment study on the motions of solid particles in liquid media with vertical temperature gradient is performed in this paper. The movement of solid spheres toward the heating end of a close cell is observed. The behavior and features of the motions examined are quite similar to thermocapillary migration of bubbles and drops in a liquid. The motion velocities of particles measured are about 10(-3) to 10(-4) mm\s. The velocity is compared with the velocity of particles floated in two liquid media. The physical mechanism of motion is explored.

Aquaculture Asia, Vol. 8, No. 1, pp.1-58, January-March 2003

*Table of Contents* Sustainable Aquaculture Fertilization, soil and water quality management in small-scale ponds part II:Soil and water quality management S. Adhikari Fisheries and aquaculture activities in Nepal Tek Gurung Peter Edwards writes on rural aquaculture: A knowledge-base for rural aquaculture Farmers as Scientists: Commercialization of giant freshwater prawn culture in India M.C. Nandeesha Aquaculture in reservoir fed canal based irrigation systems of India – a boon for fish production K.M. Rajesh, Mridula R. Mendon, K. N. Prabhudeva and P. Arun Padiyar Research and Farming Techniques Production and grow-out of the Black-lip pearl oyster Pinctada margaritifera Idris Lane Breeding of carps using a low-cost, small-scale hatchery in Assam, India: A farmer proven technology S.K. Das Genes and Fish: Hybridisation – more trouble than its worth? Graham Mair Breeding and culture of the sea cucumber Holothuria scabra in Vietnam R. Pitt and N. D. Q. Duy The potential use of palm kernel meal in aquaculture feeds Wing-Keong Ng Using a Simple GIS model to assess development patterns of small-scale rural aquaculture in the wider environment Simon R. Bush Aquaculture fundamentals: Getting the most out of your feed Simon Wilkinson Marine finfish section Status of marine finfish aquaculture in Myanmar U Khin Kolay Regional training course on grouper hatchery production Aquatic Animal Health Advice on aquatic animal health care: Problems in Penaeus monodon culture in low salinity areas Pornlerd Chanratchakool

Earth Systems: the foundation of Florida’s Ecosystems

(1 poster)

Numerical Research on Liquid Spray in Supersonic Cross Flow

Numerical simulation was conducted to characterize the kerosene spray injecting into supersonic cross flow, especially focusing on the aerodynamic secondary breakup effect of the supersonic cross flow on the initial droplets. It was revealed that the initial parent drops were broken up into small drops whose diameter is about O(10) micrometers soon after they entered into the supersonic cross flow. During the appropriate range of initial drop size, the parent droplets would be broken up into small drops with the same magnitude diameter no matter how large the initial drops SMD was.

Numerical Study on Kerosene Spray in Supersonic Flow

Numerical simulation was conducted to study the kerosene spray characteristics injecting into supersonic cross flow. The verification of the simulation was carried out by experimental Schlieren image, and the agreement was obtained by compared the spray plume pictures. Furthermore, the aerodynamic secondary breakup effect of the supersonic cross flow on the initial droplets was investigated. It was revealed that the initial parent drops were broken up into small drops whose diameter is about O(10) micrometers soon after they entered into the supersonic cross flow. During the appropriate range of initial drop size, the parent droplets would be broken up into small drops with the same magnitude diameter no matter how large the initial drops SMD was.

Torsion fracture behavior of drawn pearlitic steel wires with different heat treatments

In this paper, torsion fracture behavior of drawn pearlitic steel wires with different heat treatments was investigated. Samples with different heat treatments was investigated. Samples with different heat treatment conditions were subjected to torsion and tensile tests. The shear strain along the torsion sample after fracture was measured. Fracture surface of wires was examined by Scanning Electron Microscopy. In addition, the method of Differential Scanning Calorimetry was used to characterize the thermodynamic process in the heat treatment. A numerical simulation via finite element method on temperature field evolution for the wire during heat treatment process was performed. The results show that both strain aging and recovery process occur in the material within the temperature range between room temperature and 435 degrees C. It was shown that the ductility measured by the number of twists drops at short heating times and recovers after further heating in the lead bath of 435 degrees C. On the other hand, the strenght of the wire increases at short heating times and decreases after further heating. The microstructure inhomogeneity due to short period of heat treatment, coupled with the gradient characteristics of shear deformation during torsion results in localized shear deformation of the wire. In this situation, shear cracks nucleate between lamella and the wire breaks with low number of twists.

Design, Construction and Testing of a Hydraulic Power Take-Off for Wave Energy Converters

This paper presents the construction, mathematical modeling and testing of a scaled universal hydraulic Power Take-Off (PTO) device for Wave Energy Converters (WECs). A specific prototype and test bench were designed and built to carry out the tests. The results obtained from these tests were used to adjust an in-house mathematical model. The PTO was initially designed to be coupled to a scaled wave energy capture device with a low speed and high torque oscillating motion and high power fluctuations. Any Energy Capture Device (ECD) that fulfils these requirements can be coupled to this PTO, provided that its scale is adequately defined depending on the rated power of the full scale prototype. The initial calibration included estimation of the pressure drops in the different components, the pressurization time of the oil inside the hydraulic cylinders and the volumetric efficiency of the complete circuit. Since the overall efficiency measured during the tests ranged from 0.69 to 0.8 and the dynamic performance of the PTO was satisfactory, the results are really promising and it is believed that this solution might prove effective in real devices.

Uncertain Information Structures and Backward Induction

In everyday economic interactions, it is not clear whether sequential choices are visible or not to other participants: agents might be deluded about opponents'capacity to acquire,interpret or keep track of data, or might simply unexpectedly forget what they previously observed (but not chose). Following this idea, this paper drops the assumption that the information structure of extensive-form games is commonly known; that is, it introduces uncertainty into players' capacity to observe each others' past choices. Using this approach, our main result provides the following epistemic characterisation: if players (i) are rational,(ii) have strong belief in both opponents' rationality and opponents' capacity to observe others' choices, and (iii) have common belief in both opponents' future rationality and op-ponents' future capacity to observe others' choices, then the backward induction outcome obtains. Consequently, we do not require perfect information, and players observing each others' choices is often irrelevant from a strategic point of view. The analysis extends {from generic games with perfect information to games with not necessarily perfect information{the work by Battigalli and Siniscalchi (2002) and Perea (2014), who provide different sufficient epistemic conditions for the backward induction outcome.

Prevalence Of Shear Banding In Compression Of Zr41Ti14Cu12.5Ni10Be22.5 Pillars As Small As 150 Nm In Diameter

Recently, the size dependence of mechanical behaviors, particularly the yield strength and plastic deformation mode, of bulk metallic glasses (BMG) has created a great deal of interest. Contradicting conclusions have been drawn by different research groups, based on various experiments on different BMG systems. Based on in situ compression transmission electron microscopy (TEM) experiments on Zr41Ti14Cu12.5Ni10Be22.5 (Vit 1) nanopillars, this paper provides strong evidence that shear banding still prevails at specimen length scales as small as 150 nm in diameter. This is supported by in situ and ex situ images of shear bands, and by the carefully recorded displacement bursts under load control its well as load drops under displacement control. Finite element modeling of the stress state within the pillar shows that the unavoidable geometry constraints accompanying such experiments impart a strong effect on the experimental results, including non-uniform stress distributions and high level hydrostatic pressures. The seemingly improved compressive ductility is believed to be due to such geometry constraints. Observations underscore the notion that the mechanical behavior of metallic glasses, including strength and plastic deformation mode, is size independent at least in Vit 1. (C) 2009 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.