Estudo de cargas térmicas de uma aeronave e dimensionamento de um sistema de ar condicionado

This work deals with the thermal load study of a fictitious aircraft as well as scaling, in terms of the airflow and temperature of the air conditioning system, for heating and cooling of the its internal environment, aiming the thermal comfort of occupants. The first part is presented the techniques and methods utilized for modeling different heat exchanges that occur in the aircraft and then allowed to calculate the total heat load and the airflow and temperature necessary to comply with the requirements of the thermal comfort. Techniques to determine the basic parameters, as convection coefficient and global coefficient of heat exchange, are also presented. The work aims to develop a program, using a computational tool, to automate the calculations so that facilitate this study. It also allows to be used for other airplanes just changing parameters and the control variables related to the specific project. Finally the program performs calculations for a fictitious airplane, to analyze its functionality and the influence of parameters involved in the temperature controls. The program allowed analyzing the sensitivity of portions of the thermal load and the corresponding parameters of influence, as well as the scaling of the air conditioning in terms of airflow and temperature. It was considered, despite the simplifications, a good approximation to the actual values and then can be used in development of the other airplanes

Eficiência energética em ar condicionado e refrigeração através da aplicação da termoacumulação

The use of refrigeration and air conditioning systems is of fundamental importance when it comes to air-conditioning of environments. Also important is the use of electricity for equipments’ operation related to these systems. Due to high cost of charging for this type of energy, factors economy and efficiency occupy key roles among design parameters of a system. One of the ways to get this economy is the use of a technique called thermal storage, or cold storage, which intends to move the required loads during peak time and also their equalizing, so that the energy is transferred from the peak time to non-peak time, thereby reducing the cost of energy consumed. Cold can be stored in the form of ice or ice water. This work aims to perform a technical-economic analysis of a mall located in Vale do Paraíba checking the feasibility of deploying a thermal storage system to achieve an economy in the cost of the energy used by the establishment. Through the parameters measured by the concessionaire of energy we can get the values of energy demand and power consumed, which will serve as basis for calculation for the study. The results obtained allow the development of two alternative proposals to the current configuration, one chosen by the criteria and results presented by technical-economic and energy analysis

Estudo e seleção de um aparelho de ar condicionado para ônibus

The study and selection of an equipment of air conditioner for any type of environment, should be made without overestimate or undersizing the project. The undersizing does not provide an adequate comfort temperature if the environment is too hot because the air conditioner does not remove all the heat necessary in the environment. But if the project is oversized, energy consumption is higher and there is an unnecessary cost. To prevent these failures is necessary to make a calculation of the thermal load on the environment and choose the equipment that has a higher cooling capacity than the calculated heat load and closer to the calculated heat load. In this graduate work will be chosen an air-conditioned equipment for bus, showing the calculations made for the thermal load for various types of heat gain in this type of vehicle. The thermal load on vehicles is more complicated to calculate than in areas because there are several factors that vary with the movement of the vehicle. It will also explain the compression refrigeration cycle, which is the cooling system used in vehicles because it is weightless, compact and lower cost. From the calculated heat load, it will be chosen an air conditioner that best suits the project and, finally, a brief presentation of the selected equipment will be made

Projeto de uma rede de ar comprimido industrial

In this study was shown the historical uses of compressed air by humanity, the general scenario of its uses and the most important steps of a project to set up an industrial network of compressed air, from the selection of a suitable compressor to the design of a distribution network, discussing all the possibilities and their characteristics as well as the feasibility of them. A case study was conducted in a food company where was implemented an industrial compressed air network. Information was collected regarding the consumers points of compressed air, as well as the layout of the new facility, necessary for the development of the distribution system. Two methods were used, analytical and nomogram, which complemented each other to the definition of appropriated tubing, both financially and physically

Consumo e incorporação de água na produção de commodities brasileiras

Water is one of the main inputs in agribusiness and is traded indirectly through the sale of agricultural products such as orange (juice or fresh) and cane sugar (ethanol and refined sugar). This study aims to estimate the proportional mass of water present in the products exported in the form of agricultural commodities considering the amount of water incorporated into the product in its genesis by plant photosynthesis, reinforcing a reflection on virtual and real water export, as well to indicate subsidies to management, planning and taxing of water resources

Desenvolvimento e caracterização de sistemas líquido cristalinos para incorporação de p-metoxicinamato de octila

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Incorporação do trans-resveratrol em sistemas nanoestruturados: avaliação das ações antioxidante e despigmentante in vitro

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Aspectos técnicos e ambientais da incorporação de novas tecnologias no setor sucroalcooleiro: produção de hidrogênio e gaseificação do bagaço

The purpose of this work is to study the incorporation of hydrogen production (Case A) and the process of gasification of sugarcane bagasse associated with combined cycle gas turbine and steam turbine (Case B) for Distillery Pioneers process. These technologies can be used to improve the energy supply in the sugarcane mill. Initially the processes for obtaining sugar and ethanol from sugarcane is discussed, with a theoretical introduction to hydrogen, the process of steam reforming and gasification of biomass (bagasse) by inserting a turbine associated with the recovery boiler gas. Subsequently makes up the energy and exergy analysis of the incorporation of the above technologies. In end stage makes it an ecological analysis considering or not the carbon cycle (photosynthesis), to determine the levels of emissions of pollutants, carbon dioxide equivalent, indicators of pollution and ecological efficiencies associated with technological developments proposed. It is concluded that hydrogen production by steam reforming of ethanol and gasification of bagasse are viable alternatives from the point of view of technical and environmental applications in the biofuels industry, contributing to the development of the sector in the country

Síntese, incorporação e liberação prolongada do tetradecapeptídeo OGP em celulose bacteriana

Este trabalho apresenta o estudo de dois sistemas de liberação prolongada, microemulsão e lipossomas, contendo peptídeo regulatório de fatores de crescimento, “osteogenic growth peptide” OGP, para aplicação em regeneração óssea. A base de adsorção para estes sistemas de liberação foi a celulose bacteriana (CB) produzida pela bactéria Gluconacetobacter xylinus. Foi escolhida devido às suas propriedades físicas e químicas, tais como como alta resistência à corrosão química, bio absorção, biocompatibilidade, porosidade e ainda boa resistência mecânica, o que a torna um biopolímero com grande potencial a ser explorado pela ciência biomédica. Estudos in vitro foram realizados para avaliar o perfil de liberação do peptídeo dos diferentes sistemas de liberação prolongada. O peptídeo OGP foi sintetizado pelo método da fase sólida (estratégia SPFS Fmoc); foi purificado e caracterizado por HPLC, espectrometria de massas e análise de aminoácidos e, em seguida, marcados com 5,6 carboxifluoresceína (CF) para análise por espectroscopia de fluorescência. O peptídeo marcado foi incorporado aos sistemas de liberação no momento do respectivo preparo, foram adsorvidos na CB por um período de 72h, seguido de sua liberação prolongada em sistema fechado de fluxo constante contendo tampão PBS pH 7,4, por um período de 24h. Após a análise da liberação, observou se que o sistema que obteve melhor resultado foi a microemulsão, sendo sua liberação prolongada nas primeiras 6,5 h, liberando 21,5% do valor teórico de peptídeo incorporado, seguido de uma liberação constante a partir desse período. Dessa forma, tem se que a microemulsão pode ser um sistema promissor para liberação prolongada do OGP em processos de regeneração óssea

Avaliação da expressão proteica de PTEN, MDM2, P53 e AR em lesões proliferativas da próstata canina

Pós-graduação em Medicina Veterinária - FCAV

Incorporação de novas tecnologias no setor sucroalcooleiro: produção de hidrogênio e aumento da oferta de eletricidade

This work studies the incorporation of new technologies in the sugarcane sector. Are considered the ethanol steam reforming and the gasification of sugarcane bagasse(by-product) processes associated with combined cycle systems (Gas Turbine + Steam Turbine), aggregating hydrogen production and increased electricity supply in the sector, respectively. To verify the technical feasibility of the incorporation processes was performed a thermodynamic analysis, considering data from a typical Brazilian Sugar Cane Industry. In another step the economic viability study of the hydrogen production process was made, with consideration on hydrated and anhydrous ethanol steam reform, comparing the cost of hydrogen production. Also considered studies of economic engineering of the gasification process and the generation of electricity associated. As conclusions, it follows that the ethanol steam reforming is a great alternative for hydrogen production, presenting production cost relatively low, especially when is considered the steam reforming of hydrated ethanol. For the gasification process associated with combined cycle, can be observed an increase of 8.56 times of the electricity production in the sugar cane industry, indicating a positive annual saving when the sales price of the supply electricity is greater than 0.070 US$/kWh. Finally it can be concluded that the incorporation of these new processes allow greater profitability and operational flexibility of Brazilian sugarcane mills

Incorporação da apatita na superfície da liga Ti30ta empregando tratamento alcalino associado à eletrofiação de fibras de PCL

Pós-graduação em Engenharia Mecânica - FEG

Aspectos histopatológicos e expressão de receptores hormonais (AR e ERα) na próstata de ratos expostos ao Di-n-Butil-Ftalato (DBP) desde o período fetal, iniciados pela N-Metil-N-Nitrosuréia (MNU)

Tendo em vista a problemática mundial com relação à degradação dos materiais plásticos e sua dispersão no meio ambiente, e diante de estudo realizado anteriormente onde se observou alterações histopatológicas e bioquímicas na próstata de animais expostos ao DBP (Di-N-Butil-ftalato) no período perinatal, este estudo teve por objetivo avaliar o potencial carcinogênico do DBP administrado desde o período fetal e após iniciação pelo MNU em um modelo de carcinogênese prostática. Ratas prenhes foram divididas em 4 grupos experimentais: 2 tratados: n=16/grupo (TDBP100 e TDBP500) e 2 controles: n=8/grupo (CN e CMNU). O grupo TDBP100 foi exposto ao DBP (100 mg/kg) e o TDBP500 a 500 mg/kg do 15º. dia de gestação (DG15) até a 21º. dia pósnatal (DPN21), enquanto que os animais controle receberam o veículo. Após o desmame, os machos foram separados e os grupos tratados e CMNU receberam dose única de MNU (50 mg/Kg, i.p.) na 6ª. semana pós-natal. Metade dos animais tratados (n=8/grupo) continuaram recebendo o DBP (DBP100+ e DBP500+) após o desmame em doses semanais até o dia do sacrifício (DPN180), enquanto os demais foram mantidos pelo mesmo período sem tratamento (DBP100- e DBP500-).Após a aplicação do MNU, os animais foram submetidos a injeções semanais de Cipionato de Testosterona (promotor) 2mg/aplicação. No dia do sacrifício, o sangue foi coletado, os órgãos reprodutores foram pesados e fragmentos do lobo ventral da próstata foram processados para inclusão em resina e Paraplast para as análises estruturais; e imunocitoquímicas para a detecção de AR e ER. Fragmentos de próstata ventral foram congelados e estocados a -80ºC e após extração das proteínas, estas foram destinadas à reação de Western Blot para avaliar a expressão das mesmas proteínas. Houve diminuição na distância anogenital nos animais DBP500 no DPN1 quando comparado com o grupo controle apontando para o efeito efetivo do DBP ...

Analise técnica, econômica e ecológica da incorporação de sistemas de gaseificação de bagaço de cana-de-açúcar no setor sucroalcooleiro: uso de ciclos combinados para o aumento da oferta de eletricidade

Pós-graduação em Engenharia Mecânica - FEG

Avaliação da aplicação de ondas de ultra-som sobre cimentos de ionômero de vidro: rugosidade superficial e dureza

The application of ultrasonic waves during the initial setting of the glass ionomer cements (GIC) has demonstrated increase of the cure speed, reduction of air bubbles and improves in some mechanical properties. The aim of this study was to evaluate the effect of the ultrasound on the microhardness and the superficial roughness in two GICs (FUJI IX GP (GC Corporation) and Ketac Molar EasyMix (3M ESPE)). Forty specimens were confectioned, twenty for evaluation of the superficial roughness and twenty for evaluation of the microhardness. Half of them received for thirty seconds the ultrasonic waves application. The readings of the roughness had been carried before and after the toothbrushing test. The twenty remaining specimens had been polished with abrasive sandpapers of decreasing granulations and submitted to the hardness test. The results, analyzed for the variance analysis (ANOVA) (p<0,05), had demonstrated increase of the hardness for all the groups with the application of ultrasonic waves, being bigger for the Ketac Molar EasyMix. The ultrasound application also caused significant reduction of the superficial roughness for the Ketac Molar EasyMix. After the toothbrushing test, this last property increased for all the materials. It could be concluded that the application of ultrasonic waves was effective in increasing the superficial hardness of the materials and that it improved the roughness of the Ketac Molar EasyMix before the toothbrushing test.