Characterization of parasitics from scattering parameters of laser diode

A novel method for characterizing the parasitics of parasitic network is proposed based on the relations between the scattering parameters of a semiconductor laser chip and laser diode. Experiments are designed and performed using our method. The analysis results are in good agreement with the measurements. Furthermore, how the parasitics change with the parasitic element values are investigated. The method only needs reflection coefficient of laser diode to be measured, which is simple because of the developed electrical-domain measurement techniques. 2007 Wiley Periodicals, Inc.

40-Gb/s Low Chirp Electroabsorption Modulator Integrated With DFB Laser

A 40-Gb/s monolithically integrated transmitter containing an InGaAsP multiple-quantum-well electroabsorption modulator (EAM) with lumped electrode and a distributed-feedback semiconductor laser is demonstrated. Superior characteristics are exhibited for the device, such as low threshold current of 20 mA, over 40-dB sidemode suppression ratio at 1550 nm, and more than 30-dB dc extinction ratio when coupled into a single-mode fiber. By adopting a deep ridge waveguide and planar electrode structures combined with buried benzocyclobutene, the capacitance of the EAM is reduced to 0.18 pF and the small-signal modulation bandwidth exceeds 33 GHz. Negative chirp operation is also realized when the bias voltage is beyond 1.6 V.

Mode characteristics of semiconductor equilateral triangle microcavities with side length of 5-20 mu m

Semiconductor equilateral triangle microresonators (ETRs) with side length of 5, 10, and 20 mum are fabricated by the two-step inductively coupled plasma (ICP) etching technique. The mode properties of fabricated InGaAsP ETRs are investigated experimentally by photoluminescence (PL) with the pumping source of a 980-nm semiconductor laser and distinct peaks are observed in the measured PL spectra. The wavelength spacings of the distinct peaks agree very well with the theoretical longitudinal mode intervals of the fundamental transverse modes in the ETRs, which verifies that the distinct peaks are corresponding to the enhancement of resonant modes. The mode quality factors are calculated from the width of the resonant peaks of the PL spectra, which are about 100 for the ETR with side length of 20 mum.

Methods for characterization of packaging parasitics of semiconductor lasers

Two novel methods for analyzing the parasitics of packaging networks are proposed based on the relations between the scattering parameters of a semiconductor laser before and after packaging, and the experiments are designed and performed using our methods. It is found that the analysis results of the two methods are in good agreement with the measurements. Either of the two methods can provide an alternative approach for characterizing the packaging parasitics for semiconductor lasers, and both are convenient due to the developed measurement techniques. (c) 2005 Wiley Periodicals, Inc.

Subtraction of scattering parameters for small-signal modulation characteristics of laser diode

An extended subtraction method of scattering parameters for characterizing laser diode is proposed in this paper. The intrinsic response is extracted from the measured transmission coefficients of laser diode, and the parasitics of packaging net-work laser chip are determined from the measured reflection coefficient of laser diode simultaneously. It is shown that the theories agree well with the experimental results.

Measurement of gain spectrum for semiconductor lasers utilizing integrations of product of emission spectrum and a phase function over one mode interval

A technique based on the integrations of the product of amplified spontaneous emission spectrum and a phase function over one mode interval is proposed for measuring gain spectrum for Fabry-Perot semiconductor lasers, and a gain correction factor related to the response function of the optical spectrum analyzer (OSA) is obtained for improving the accuracy of measured gain spectrum. The gain spectra with a difference less than 1.3 cm(-1) from 1500 to 1600 nm are obtained for a 250-mum-long semiconductor laser at the OSA resolution of 0.06, 0.1, 0.2, and 0.5 nm. The corresponding gain correction factor is about 9 cm(-1) at the resolution of 0.5 nm. The gain spectrum measured at the resolution of 0.5 nm has the same accuracy as that obtained by the Hakki-Paoli method at the resolution of 0.06 nm for the laser with the mode interval of 1.3 nm.

Measurement of gain spectrum for Fabry-Perot semiconductor lasers by the Fourier transform method with a deconvolution process

To improve the accuracy of measured gain spectra, which is usually limited by the resolution of the optical spectrum analyzer (OSA), a deconvolution process based on the measured spectrum of a narrow linewidth semiconductor laser is applied in the Fourier transform method. The numerical simulation shows that practical gain spectra can be resumed by the Fourier transform method with the deconvolution process. Taking the OSA resolution to be 0.06, 0.1, and 0.2 nm, the gain-reflectivity product spectra with the difference of about 2% are obtained for a 1550-nm semiconductor laser with the cavity length of 720 pm. The spectra obtained by the Fourier transform method without the deconvolution process and the Hakki-Paoli method are presented and compared. The simulation also shows that the Fourier transform method has less sensitivity to noise than the Hakki-Paoli method.

Studies of 6H-SiC devices

Silicon carbide (SiC) is recently receiving increased attention due to its unique electrical and thermal properties. It has been regarded as the most appropriate semiconductor material for high power, high frequency, high temperature, and radiation hard microelectronic devices. The fabrication processes and characterization of basic device on 6H-SiC were systematically studied. The main works are summarized as follows:The homoepitaxial growth on the commercially available single-crystal 6H-SiC wafers was performed in a modified gas source molecular beam epitaxy system. The mesa structured p(+)n junction diodes on the material were fabricated and characterized. The diodes showed a high breakdown voltage of 800 V at room temperature. They operated with good rectification characteristics from room temperature to 673 K.Using thermal evaporation, Ti/6H-SiC Schottky barrier diodes were fabricated. They showed good rectification characteristics from room temperature to 473 K. Using neon implantation to form the edge termination, the breakdown voltage was improved to be 800 V.n-Type 6H-SiC MOS capacitors were fabricated and characterized. Under the same growing conditions, the quality of polysilicon gate capacitors was better than Al. In addition, SiC MOS capacitors had good tolerance to gamma rays. (C) 2002 Published by Elsevier Science B.V.

Scattering-parameter measurements of laser diodes

An accurate and simple technique for measuring the input reflection coefficient and the frequency response of semiconductor laser diode chips is proposed and demonstrated. All the packaging parasitics could be obtained accurately using a calibrated probe, and the impedance of the intrinsic diode chip is deduced from the directly measured reflection coefficient. The directly measured impedance of a laser diode is affected strongly by the short bond wire. In the frequency response (S(2)1) measurements of semiconductor laser diode chips, the test fixture consists of a microwave probe, a submount, and a bond wire. The S-parameters of the probe could be determined using the short-open-match (SOM) method. Both the attenuation and the reflection of the test fixture have a strong influence on the directly measured frequency response, and in our proposed technique, the effect of test fixture is completely removed.

Lasing of CdSexS1-x quantum dots in a glass spherical microcavity

A glass spherical microcavity only a few microns in diameter embedded with CdSexS1-x quantum dots (QDs) was fabricated using a physical method; it exhibited good optical stability under continuous-wave laser excitation with high power. We investigated the excitation power dependences of the emission intensity and the linewidth of both transverse electric and transverse magnetic resonance peaks of whispering gallery modes. Stimulated emission behaviour of multi-frequency modes is observed at room temperature. The low threshold value and large mode separation makes QD-containing microspheres promising for visible microlaser applications.

Room-temperature, ground-state lasing for red-emitting vertically aligned InAlAs/AlGaAs quantum dots grown on a GaAs(100) substrate

The effect of the growth temperature on the properties of InAlAs/AlGaAs quantum dots grown on GaAs(100) substrates is investigated. The optical efficiency and structural uniformity are improved by increasing the growth temperature from 530 to 560 degreesC. The improvements of InAlAs/AlGaAs quantum-dot characteristics could be explained by suppressing the incorporation of oxygen and the formation of group-III vacancies. Furthermore, edge-emitting laser diodes with six quantum-dot layers grown at 560 degreesC have been fabricated. Lasing occurs via the ground state at 725 nm, with a room-temperature threshold current density of 3.9 kA/cm(2), significantly better than previously reported values for this quantum-dot systems. (C) 2002 American Institute of Physics.

Analysis of semiconductor microlasers with an equilateral triangle resonator by rate equations

Semiconductor microlasers with an equilateral triangle resonator (ETR) are analyzed by rate equations with the mode lifetimes calculated by the finite-difference time-domain technique and the Pade approximation. A gain spectrum based on the relation of the gain spectrum and the spontaneous emission spectrum is proposed for considering the mode selection in a wide wavelength span. For an ETR microlaser with the side length of about 5 mum, we find that single fundamental mode operation at about 1.55 mum can be obtained as the side length increases from 4.75 to 5.05 mum. The corresponding wavelength tuning range is 93 nm, and the threshold current is about 0.1 to 0.4 mA.

Analysis and numerical simulation of eigenmode characteristics for semiconductor lasers with an equilateral triangle micro-resonator

The eigenmodes confined in the equilateral triangle resonator (ETR) are analyzed by deriving the eigenvalues and the mode field distributions and by the finite difference time domain (FDTD) technique. The analytical results show that the one-period-length for the mode light rays inside the ETR is the perimeter of the ETR, and the number of transverse modes is limited by the condition of total internal reflection. In addition, the sum of the longitudinal mode index and the transverse mode index should be an even number, which limits the number of confined modes again. Based on the FDTD technique and the Pade approximation, we calculate the mode resonant frequencies and the quality factors from the local maximum and the width of the spectral distribution of the intensity The numerical results of mode frequencies agree very well with the analytical results, and the quality factor of the fundamental mode is usually higher than that of the higher order transverse modes. The results show that the ETR is suitable to realize single-made operation as semiconductor microcavity lasers.

AlGaInP visible quantum well lasers for information technology

650 nm-range AlGaInP multi-quantum well (MQW) laser diodes grown by low pressure metal organic chemical vapor deposition (LP-MOCVD) have been studied and the results are presented in this paper. Threshold current density of broad area contact laser diodes can be as low as 350 A/cm(2). Laser diodes with buried-ridge strip waveguide structures were made, threshold currents and differential efficiencies are (22-40) mA and (0.2-0.7) mW/mA, respectively. Typical output power for the laser diodes is 5 mW, maximum output power of 15 mW has been obtained. Their operation temperature can be up to 90 degrees C under power of 5 mW. After operating under 90 degrees C and 5 mW for 72 hrs, the average increments for the threshold currents of the lasers at 25 degrees C and the operation currents at 5 mW (at 25 degrees C) are (2-3) mA and (3-5) mA, respectively. Reliability tests showed that no obvious degradation was observed after 1400 hours of CW operation under 50 degrees C and 2.5 mW.

A novel ultra low power temperature sensor for UHF RFID tag chip

A novel ultra low power temperature sensor for UHF RFID tag chip is presented. The sensor consists of a constant pulse generator, a temperature related oscillator, a counter and a bias. Conversion of temperature to digital output is fulfilled by counting the number of the clocks of the temperature related oscillator in a constant pulse period. The sensor uses time domain comparing, where high power consumption bandgap voltage references and traditional ADCs are not needed. The sensor is realized in a standard 0.18 mu m CMOS process, and the area is only 0.2mm(2). The accuracy of the temperature sensor is +/- 1 degrees C after calibration. The power consumption of the sensor is only 0.9 mu W.