Thermochemical characterisation of various biomass feedstock and bio-oil generated by fast pyrolysis

The projected decline in fossil fuel availability, environmental concerns, and security of supply attract increased interest in renewable energy derived from biomass. Fast pyrolysis is a possible thermochemical conversion route for the production of bio-oil, with promising advantages. The purpose of the experiments reported in this thesis was to extend our understanding of the fast pyrolysis process for straw, perennial grasses and hardwoods, and the implications of selective pyrolysis, crop harvest and storage on the thermal decomposition products. To this end, characterisation and laboratory-scale fast pyrolysis were conducted on the available feedstocks, and their products were compared. The variation in light and medium volatile decomposition products was investigated at different pyrolysis temperatures and heating rates, and a comparison of fast and slow pyrolysis products was conducted. Feedstocks from different harvests, storage durations and locations were characterised and compared in terms of their fuel and chemical properties. A range of analytical (e.g. Py-GC-MS and TGA) and processing equipment (0.3 kg/h and 1.0 kg/h fast pyrolysis reactors and 0.15 kg slow pyrolysis reactor) was used. Findings show that the high bio-oil and char heating value, and low water content of willow short rotation coppice (SRC) make this crop attractive for fast pyrolysis processing compared to the other investigated feedstocks in this project. From the analytical sequential investigation of willow SRC, it was found that the volatile product distribution can be tailored to achieve a better final product, by a variation of the heating rate and temperature. Time of harvest was most influential on the fuel properties of miscanthus; overall the late harvest produced the best fuel properties (high HHV, low moisture content, high volatile content, low ash content), and storage of the feedstock reduced the moisture and acid content.

Resveratrol and the eye:activity and molecular mechanisms

Purpose: Alcohol consumption is inversely correlated with the incidence of cardiovascular disease. It is thought that red wine is specifically responsible for these cardiovascular benefits, due to its ability to reduce vascular inflammation, facilitate vasorelaxation, and inhibit angiogenesis. This is because of its high polyphenolic content. Resveratrol is the main biologically active polyphenol within red wine. Owing to its vascular-enhancing properties, resveratrol may be effective in the microcirculation of the eye, thereby helping prevent ocular diseases such as age-related macular degeneration, diabetic retinopathy, and glaucoma. Such conditions are accountable for worldwide prevalence of visual loss. Method: A review of the relevant literature was conducted on the ScienceDirect, Web of Science, and PubMed databases. Key words used to carry out the searches included 'red wine', 'polyphenols', 'resveratrol', 'eye' and 'ocular'. Articles relating to the effects of resveratrol on the eye were reviewed. Results: The protective effects of resveratrol within the eye are extensive. It has been demonstrated to have anti-oxidant, anti-apoptotic, anti-tumourogenic, anti-inflammatory, anti-angiogenic and vasorelaxant properties. There are potential benefits of resveratrol supplementation across a wide range of ocular diseases. The molecular mechanisms underlying these protective actions are diverse. Conclusion: Evidence suggests that resveratrol may have potential in the treatment of several ocular diseases. However, while there are many studies indicating plausible biological mechanisms using animal models and in-vitro retinal cells there is a paucity of human research. The evidence base for the use of resveratrol in the management of ocular diseases needs to be increased before recommendations can be made for the use of resveratrol as an ocular supplement. © 2014 Springer-Verlag.

Experiments on the generation of activated carbon from biomass

Activated carbon is generated from various waste biomass sources like rice straw, wheat straw, wheat straw pellets, olive stones, pistachios shells, walnut shells, beech wood and hardcoal. After drying the biomass is pyrolysed in the temperature range of 500-600 °C at low heating rates of 10 K/min. The activation of the chars is performed as steam activation at temperatures between 800 °C and 900 °C. Both the pyrolysis and activation experiments were run in lab-scale facilities. It is shown that nut shells provide high active surfaces of 1000-1300 m/g whereas the active surface of straw matters does hardly exceed 800 m/g which might be a result of the high ash content of the straws and the slightly higher carbon content of the nut shells. The active surface is detected by BET method. Besides the testing of a many types of biomass for the suitability as base material in the activated carbon production process, the experiments allow for the determination of production parameters like heating rate and pyrolysis temperature, activation time and temperature as well as steam flux which are necessary for the scale up of the process chain. © 2006 Elsevier B.V. All rights reserved.

Internet search:subdivision-based interactive query expansion and the soft semantic web

The expansion of the Internet has made the task of searching a crucial one. Internet users, however, have to make a great effort in order to formulate a search query that returns the required results. Many methods have been devised to assist in this task by helping the users modify their query to give better results. In this paper we propose an interactive method for query expansion. It is based on the observation that documents are often found to contain terms with high information content, which can summarise their subject matter. We present experimental results, which demonstrate that our approach significantly shortens the time required in order to accomplish a certain task by performing web searches.

Thermochemical conversion of Brewers Spent Grain combined with catalytic reforming of pyrolysis vapours

The brewing process is an energy intensive process that uses large quantities of heat and electricity. To produce this energy requires a high, mainly fossil fuel consumption and the cost of this is increasing each year due to rising fuel costs. One of the main by-products from the brewing process is Brewers Spent Grain (BSG), an organic residue with very high moisture content. It is widely available each year and is often given away as cattle feed or disposed of to landfill as waste. Currently these methods of disposal are also costly to the brewing process. The focus of this work was to investigate the energy potential of BSG via pyrolysis, gasification and catalytic steam reforming, in order to produce a tar-free useable fuel gas that can be combusted in a CHP plant to develop heat and electricity. The heat and electricity can either be used on site or exported. The first stage of this work was the drying and pre-treatment of BSG followed by characterisation to determine its basic composition and structure so it can be evaluated for its usefulness as a fuel. A thorough analysis of the characterisation results helps to better understand the thermal behaviour of BSG feedstock so it can be evaluated as a fuel when subjected to thermal conversion processes either by pyrolysis or gasification. The second stage was thermochemical conversion of the feedstock. Gasification of BSG was explored in a fixed bed downdraft gasifier unit. The study investigated whether BSG can be successfully converted by fixed bed downdraft gasification operation and whether it can produce a product gas that can potentially run an engine for heat and power. In addition the pyrolysis of BSG was explored using a novel “Pyroformer” intermediate pyrolysis reactor to investigate the behaviour of BSG under these processing conditions. The physicochemical properties and compositions of the pyrolysis fractions obtained (bio-oil, char and permanent gases) were investigated for their applicability in a combined heat power (CHP) application.

Comprehensive characterization of Napier grass as a feedstock for thermochemical conversion

Study on Napier grass leaf (NGL), stem (NGS) and leaf and stem (NGT) was carried out. Proximate, ultimate and structural analyses were evaluated. Functional groups and crystalline components in the biomass were examined. Pyrolysis study was conducted in a thermogravimetric analyzer under nitrogen atmosphere of 20 mL/min at constant heating rate of 10 K/min. The results reveal that Napier grass biomass has high volatile matter, higher heating value, high carbon content and lower ash, nitrogen and sulfur contents. Structural analysis shows that the biomass has considerable cellulose and lignin contents which are good candidates for good quality bio-oil production. From the pyrolysis study, degradation of extractives, hemicellulose, cellulose and lignin occurred at temperature around 478, 543, 600 and above 600 K, respectively. Kinetics of the process was evaluated using reaction order model. New equations that described the process were developed using the kinetic parameters and data compared with experimental data. The results of the models fit well to the experimental data. The proposed models may be a reliable means for describing thermal decomposition of lignocellulosic biomass under nitrogen atmosphere at constant heating rate.

Cellular impermeability and uptake of biocides and antibiotics in Gram-positive bacteria and mycobacteria

Gram-positive bacteria possess a permeable cell wall that usually does not restrict the penetration of antimicrobials. However, resistance due to restricted penetration can occur, as illustrated by vancomycin-intermediate resistant Staphylococcus aureus strains (VISA) which produce a markedly thickened cell wall. Alterations in these strains include increased amounts of nonamidated glutamine residues in the peptidoglycan and it is suggested that the resistance mechanism involves 'affinity trapping' of vancomycin in the thickened cell wall. VISA strains have reduced doubling times, lower sensitivity to lysostaphin and reduced autolytic activity, which may reflect changes in the D-alanyl ester content of the wall and membrane teichoic acids. Mycobacterial cell walls have a high lipid content, which is assumed to act as a major barrier to the penetration of antimicrobial agents. Relatively hydrophobic antibiotics such as rifampicin and fluoroquinolones may be able to cross the cell wall by diffusion through the hydrophobic bilayer composed of long chain length mycolic acids and glycolipids. Hydrophilic antibiotics and nutrients cannot diffuse across this layer and are thought to use porin channels which have been reported in many species of mycobacteria. The occurrence of porins in a lipid bilayer supports the view that the mycobacterial wall has an outer membrane analogous to that of gram-negative bacteria. However, mycobacterial porins are much less abundant than in the gram-negative outer membrane and allow only low rates of uptake for small hydrophilic nutrients and antibiotics.

Factors affecting the nodulation and growth of tropical woody legume seedlings

This study surveys the occurrence of nodulation in woody legume species in Panamá and Costa Rica, describes nodule and root characteristics, and researches host-bacteria specificity, nodulation potential of soils, and the effects of light, added nitrogen, and rhizobia and VA mycorrhizal fungi inoculation on seedling growth. I examined 83 species in 37 genera and found 80% to be nodulated. Percent nodulated species in the Caesalpinioideae, Mimosoideae, and Papilionoideae was 17, 95, and 86, respectively, with no correlation between nodule morphology and tribal classification. Nodules formed mainly at root branch points which supports epidermal breaks as an important rhizobia infection route. More non-nodulated than nodulated species had root hairs. Several species emitted volatile sulfur-containing compounds, including the toxic compound ethylmercaptan, from roots, germinating seeds, and other tissues. These emissions may have an allelopathic action against pathogens, predators, or other plants. In contrast to the general non-specificity of most legumes for rhizobia, Mimosa pigra L. was highly specific and only nodulated in flooded soils. This species' specificity, combined with a limited occurrence of its root nodule bacteria may limit its natural distribution, but its spread as an invasive weed is facilitated when fill material from rivers is deposited in other areas. ^ An experimental light level of 1.5% of full sun completely inhibited seedling nodulation, as do similar naturally low levels in forest understory. In the forest, trees and seedlings were not nodulated. in some soils with suspected high N content. For six experimental species, added N progressively increased seedling growth while decreasing nodule biomass; at the highest level of added N nodulation was completely suppressed. Species and individuals showed variation in nodule biomass at high N applications which may indicate an opportunity for genetic selection for optimal N acquisition. Rhizobia inoculation had a small positive effect on seedling shoot growth, but VA mycorrhiza inoculation overwhelmingly increased seedling size, biomass, and leaf mineral concentration. In lowland tropical forest, VA mycorrhizal colonization appears indispensable for legume nodulation because of the fungus' ability to supply P in deficient soils. This requirement makes the legume-rhizobia-mycorrhiza association obligately tripartite. ^

The potential role of plant oxygen and sulphide dynamics in die-off events of the tropical seagrass, Thalassia testudinum

1 Oxygen and sulphide dynamics were examined, using microelectrode techniques, in meristems and rhizomes of the seagrass Thalassia testudinum at three different sites in Florida Bay, and in the laboratory, to evaluate the potential role of internal oxygen variability and sulphide invasion in episodes of sudden die-off. The sites differed with respect to shoot density and sediment composition, with an active die-off occurring at only one of the sites. 2 Meristematic oxygen content followed similar diel patterns at all sites with high oxygen content during the day and hyposaturation relative to the water column during the night. Minimum meristematic oxygen content was recorded around sunrise and varied among sites, with values close to zero at the die-off site. 3 Gaseous sulphide was detected within the sediment at all sites but at different concentrations among sites and within the die-off site. Spontaneous invasion of sulphide into Thalassia rhizomes was recorded at low internal oxygen partial pressure during darkness at the die-off site. 4 A laboratory experiment showed that the internal oxygen dynamics depended on light availability, and hence plant photosynthesis, and on the oxygen content of the water column controlling passive oxygen diffusion from water column to leaves and belowground tissues in the dark. 5 Sulphide invasion only occurred at low internal oxygen content, and the rate of invasion was highly dependent on the oxygen supply to roots and rhizomes. Sulphide was slowly depleted from the tissues when high oxygen partial pressures were re-established through leaf photosynthesis. Coexistence of sulphide and oxygen in the tissues and the slow rate of sulphide depletion suggest that sulphide reoxidation is not biologically mediated within the tissues of Thalassia. 6 Our results support the hypothesis that internal oxygen stress, caused by low water column oxygen content or poor plant performance governed by other environmental factors, allows invasion of sulphide and that the internal plant oxygen and sulphide dynamics potentially are key factors in the episodes of sudden die-off in beds of Thalassia testudinum . Root anoxia followed by sulphide invasion may be a more general mechanism determining the growth and survival of other rooted plants in sulphate-rich aquatic environments.

Secagem de resíduo de goiaba em secador convectivo de bandejas: modelagem matemática e análise do processo

Actually, Brazil is one of the larger fruit producer worldwide, with most of its production being consumed in nature way or either as juice or pulp. It is important to highlig ht in the fruit productive chain there are a lot lose due mainly to climate reasons, as well as storage, transportation, season, market, etc. It is known that in the pulp and fruit processing industy a yield of 50% (in mass) is usually obtained, with the other part discarded as waste. However, since most this waste has a high nutrient content it can be used to generate added - value products. In this case, drying plays an important role as an alternative process in order to improve these wastes generated by the fruit industry. However, despite the advantage of using this technique in order to improve such wastes, issues as a higher power demand as well as the thermal efficiency limitation should be addressed. Therefore, the control of the main variables in t his drying process is quite important in order to obtain operational conditions to produce a final product with the target specification as well as with a lower power cost. M athematical models can be applied to this process as a tool in order to optimize t he best conditions. The main aim of this work was to evaluate the drying behaviour of a guava industrial pulp waste using a batch system with a convective - tray dryer both experimentally and using mathematical modeling. In the experimental study , the dryin g carried out using a group of trays as well as the power consume were assayed as response to the effects of operational conditions (temperature, drying air flow rate and solid mass). Obtained results allowed observing the most significant variables in the process. On the other hand, the phenomenological mathematical model was validated and allowed to follow the moisture profile as well as the temperature in the solid and gas phases in every tray. Simulation results showed the most favorable procedure to o btain the minimum processing time as well as the lower power demand.

Pressão de sono e perfil acadêmico de estudante de medicina do 1º período da UFRN

Academic demands, new social context, new routines and decrease of the parental control, are factors that may influence the sleep pattern of freshman students at the University. Medical students from the Federal University of Rio Grande do Norte (UFRN) have a full-time course, subjects with high-level content, and, at the first semester, classes begin at 7 a.m. This group composed by young adults who still suffering with delayed sleep phase, common in adolescence, indicating that this class schedule can be inappropriate at this age. The reduction of nocturnal sleep during school days, and the attempt to recover sleep on free days – social jet lag (JLS), suggests that in the first semester, students suffer from high sleep pressure. High sleep pressure may reflect on cognitive tasks and performance. Therefore, the aim of this study was to investigate the relationship between sleep pressure and the academic profile of medical students from the first semester of UFRN, characterizing this population socio-demographically and investigating possible impacts on therestactivity rhytm and academic performance. A sample of 88 students, healthy men and women awswered the following questionnaires: Pittsburgh Sleep Quality (PSQI), Epworth Sleepiness Scale (ESS), Horne & Ostberg Chronotype (HO), Munich Chronotype (MCTQ) and “Health and Sleep” adapted. Actigraphy was used during 14 days to make actogramas and obtain non-parametric variables of the rest-activity rhythm and the grades of the morning schedule were used as academic performance. The JLS was used as a measure of sleep pressure. Statistics significance level was 95%. The population was sociodemographic homogeneous. Most students have healthy lifestyle, practice physical activity, use car to go to the university and take between 15 and 30 minutes for this route. Regarding CSV, most were classify as intermediate (38.6%) and evening (32%) chronotypes, needs to nap during the week, suffer daytime sleepiness and have poor sleep quality. 83% of the sample has at least 1h JLS, which led us to divide into two groups: Group <2h JLS (N = 44) and Group ≥ 2h JLS (N = 44). The groups have differences only in chronotype, showing that most evening individuals have more JLS, however, no differences were found in relation to sociodemographic aspect, rest-activity rhythm or academic performance. The homogeneity of the sample was limited to compare the groups, however, is alarming that students already present in the first half: JLG, poor sleep quality and excessive daytime sleepiness, which can be accentuated through the university years, with the emergence of night shifts and increased academic demand. Interventionsaddressingthe importance of good sleep habits and the change of the class start time are strategies aimed to improve student’s health.

Determinação da composição química de quatro variedades de feijão caupi (Vigna unguiculata L. Walp) cultivadas em solo potiguar

The cowpea (Vigna unguiculata L. Walp) is a major food crops in northeastern Brazil. In Rio Grande do Norte, the cowpea, vigna beans or cowpea, as it is known, has great socioeconomic importance as a source of nutrients in food, with great emphasis among agricultural products. To improve productivity and resistance to pests, two cultivars were developed exclusively by EMPARN (Agricultural Research Corporation of Rio Grande do Norte), for breeding. The samples were provided by EMPARN, two improved (Potiguar and Laugh year) and two landraces (Rib of beef and Canapu). The seeds were ground and made into flour samples and the determination of moisture and ash by graviméticos methods, lipids by Soxhlet extraction, fibers with determiner fiber, carbohydrates by difference and minerals by ICP-OES were performed except the match analyzed by UVvis. The results showed a high fiber content (55.55% and 55.32% and 50.04% improved samples and 50.32% creole samples) and protein (25.52% and 25.27% improved and 27 samples, 23% and 24.99% creole samples). Comparing the results of the mineral content, the improved cultivars stood out in relation to Ca, Co, P, Mg, Mo and Na. Creole cultivars showed better results for Cu, Cr (low), Fe, Mn, Ni, K and Zn. The results will be important in future nutritional research and to build a table of Brazilian chemical composition of foods.

Atividade antimicrobiana e antioxidante de Licania rigida e Turnera ulmifolia

Introduction: Licania rigida Benth and Turnera ulmifolia Linn. var. elegans are species of semi-arid regional plants used in the treatment of various diseases. Objectives: The purpose of this study was chemically characterize the extracts and fractions and investigate the antimicrobial and antioxidant potential. Methods: For chemical analysis, were performed spectrophotometric quantification of the total phenolic and characterization of the extracts by chromatographic analysis. Evaluation of antioxidant activity was done by determining the radical scavenging capacity DPPH •. Antimicrobial activity was evaluated by agar diffusion, broth microdilutionand time-kill assays. Results: The extracts and fractions L. rigid and T. ulmifolia showed a high phenolic content, the presence of flavonoids, which were determined as chemical markers. It was observed that the extracts of both species performed as sequestering agents in the trial of antioxidant activity in vitro. The L. rigida extract was the only active front strains of S. aureus 33591 (methicillin-resistant), S. aureus 29213, S. epidermidis 12228, and also against the yeast, Candida albicans, Candida dubliniensis, Candida tropicalis, Candida parapsilosis, Candida rugosa, Candida krusei eTrichosporon asahii. Conclusions: Based on these results it is possibly affirm the antioxidant and antimicrobial activity of L. rigida and attributed the presence of polyphenolic flavonoid like responsible.

Investigation on performance characteristics of dense graded hot mix asphalt with RAP and crumb rubber

The objective of this study was to fundamentally characterize the laboratory performance of traditional hot mix asphalt (HMA) mixtures incorporating high RAP content and waste tire crumb rubber through their fundamental engineering properties. The nominal maximum aggregates size was chosen for this research was 12mm (considering the limitation of aggregate size for surface layer) and both coarse and fine aggregates are commonly used in Italy that were examined and analyzed in this study. On the other hand, the RAP plays an important role in reducing production costs and enhancing the environmentally sustainable pavements instead of using virgin materials in HMA. Particularly, this study has aimed to use 30% of RAP content (25% fine aggregate RAP and 5% coarse aggregate RAP) and 1% of CR additives by the total weight of aggregates for mix design. The mixture of aggregates, RAP and CR were blended with different amount of unmodified binder through dry processes. Generally, the main purposes of this study were investigating on capability of using RAP and CR in dense graded HMA and comparing the performance of rejuvenator in RAP with CR. In addition, based on the engineering analyses during the study, we were able compare the fundamental Indirect Tensile Strength (ITS) value of dense graded HMA and also mechanical characteristics in terms of Indirect Tensile Stiffness Modulus (ITSM). In order to get an extended comparable data, four groups of different mixtures such as conventional mixture with only virgin aggregates (DV), mixture with RAP (DR), mixture with RAP and rejuvenator (DRR), and mixture with RAP, rejuvenator, CR (DRRCr) were investigated in this research experimentally. Finally, the results of those tests indicated that the mixtures with RAP and CR had the high stiffness and less thermal sensitivity, while the mixture with virgin aggregates only had very low values in comparison.

Experimental analysis of novel telecom source materials and devices

Incumbent telecommunication lasers emitting at 1.5 µm are fabricated on InP substrates and consist of multiple strained quantum well layers of the ternary alloy InGaAs, with barriers of InGaAsP or InGaAlAs. These lasers have been seen to exhibit very strong temperature dependence of the threshold current. This strong temperature dependence leads to a situation where external cooling equipment is required to stabilise the optical output power of these lasers. This results in a significant increase in the energy bill associated with telecommunications, as well as a large increase in equipment budgets. If the exponential growth trend of end user bandwidth demand associated with the internet continues, these inefficient lasers could see the telecommunications industry become the dominant consumer of world energy. For this reason there is strong interest in developing new, much more efficient telecommunication lasers. One avenue being investigated is the development of quantum dot lasers on InP. The confinement experienced in these low dimensional structures leads to a strong perturbation of the density of states at the band edge, and has been predicted to result in reduced temperature dependence of the threshold current in these devices. The growth of these structures is difficult due to the large lattice mismatch between InP and InAs; however, recently quantum dots elongated in one dimension, known as quantum dashes, have been demonstrated. Chapter 4 of this thesis provides an experimental analysis of one of these quantum dash lasers emitting at 1.5 µm along with a numerical investigation of threshold dynamics present in this device. Another avenue being explored to increase the efficiency of telecommunications lasers is bandstructure engineering of GaAs-based materials to emit at 1.5 µm. The cause of the strong temperature sensitivity in InP-based quantum well structures has been shown to be CHSH Auger recombination. Calculations have shown and experiments have verified that the addition of bismuth to GaAs strongly reduces the bandgap and increases the spin orbit splitting energy of the alloy GaAs1−xBix. This leads to a bandstructure condition at x = 10 % where not only is 1.5 µm emission achieved on GaAs-based material, but also the bandstructure of the material can naturally suppress the costly CHSH Auger recombination which plagues InP-based quantum-well-based material. It has been predicted that telecommunications lasers based on this material system should operate in the absence of external cooling equipment and offer electrical and optical benefits over the incumbent lasers. Chapters 5, 6, and 7 provide a first analysis of several aspects of this material system relevant to the development of high bismuth content telecommunication lasers.