A Study on Fractionation and Ultrafiltration of Proteins with Characterized Modified and Unmodified Membranes

Membrane filtration has become increasingly attractive in the processing of both foodand biotechnological products. However, the poor selectivity of the membranes and fouling are the critical factors limiting the development of UF systems for the specific fractionation of protein mixtures. This thesis gives an overview on fractionation of proteins from model protein solutions or from biological solutions. An attempt was made to improve the selectivity of the available membranes by modifying the membranes and by exploiting the different electrostatic interactions between the proteins and the membrane pore surfaces. Fractionation and UF behavior of proteins in the model solutions and in the corresponding biological solutions were compared. Characterization of the membranes and protein adsorptionto the membrane were investigated with combined flux and streaming potential studies. It has been shown that fouling of the membranes can be reduced using "self-rejecting" membranes at pH values where electrostatic repulsion is achieved between the membrane and the proteins in solution. This effect is best shown in UF of dilute single protein solutions at low ionic strengths and low pressures. Fractionation of model proteins in single, binary, and ternary solutionshas been carried out. The results have been compared to the results obtained from fractination of biological solutions. It was generally observed that fractination of proteins from biological solutions are more difficult to carry out owingto the presence of non studied protein components with different properties. Itcan be generally concluded that it is easier to enrich the smaller protein in the permeate but it is also possible to enrich the larger protein in the permeateat pH values close to the isoelectric point of the protein. It should be possible to find an optimal flux and modification to effectively improve the fractination of proteins even with very similar molar masses.

Chronic NSAID use and long-term decline of renal function in a prospective rheumatoid arthritis cohort study.

OBJECTIVES: Non-steroidal anti-inflammatory drugs (NSAIDs) may cause kidney damage. This study assessed the impact of prolonged NSAID exposure on renal function in a large rheumatoid arthritis (RA) patient cohort. METHODS: Renal function was prospectively followed between 1996 and 2007 in 4101 RA patients with multilevel mixed models for longitudinal data over a mean period of 3.2 years. Among the 2739 'NSAID users' were 1290 patients treated with cyclooxygenase type 2 selective NSAIDs, while 1362 subjects were 'NSAID naive'. Primary outcome was the estimated glomerular filtration rate according to the Cockroft-Gault formula (eGFRCG), and secondary the Modification of Diet in Renal Disease and Chronic Kidney Disease Epidemiology Collaboration formula equations and serum creatinine concentrations. In sensitivity analyses, NSAID dosing effects were compared for patients with NSAID registration in ≤/>50%, ≤/>80% or ≤/>90% of assessments. FINDINGS: In patients with baseline eGFRCG >30 mL/min, eGFRCG evolved without significant differences over time between 'NSAID users' (mean change in eGFRCG -0.87 mL/min/year, 95% CI -1.15 to -0.59) and 'NSAID naive' (-0.67 mL/min/year, 95% CI -1.26 to -0.09, p=0.63). In a multivariate Cox regression analysis adjusted for significant confounders age, sex, body mass index, arterial hypertension, heart disease and for other insignificant factors, NSAIDs were an independent predictor for accelerated renal function decline only in patients with advanced baseline renal impairment (eGFRCG <30 mL/min). Analyses with secondary outcomes and sensitivity analyses confirmed these results. CONCLUSIONS: NSAIDs had no negative impact on renal function estimates but in patients with advanced renal impairment.

Using species richness and functional traits predictions to constrain assemblage predictions from stacked species distribution models

Aim: Modelling species at the assemblage level is required to make effective forecast of global change impacts on diversity and ecosystem functioning. Community predictions may be achieved using macroecological properties of communities (MEM), or by stacking of individual species distribution models (S-SDMs). To obtain more realistic predictions of species assemblages, the SESAM framework suggests applying successive filters to the initial species source pool, by combining different modelling approaches and rules. Here we provide a first test of this framework in mountain grassland communities. Location: The western Swiss Alps. Methods: Two implementations of the SESAM framework were tested: a "Probability ranking" rule based on species richness predictions and rough probabilities from SDMs, and a "Trait range" rule that uses the predicted upper and lower bound of community-level distribution of three different functional traits (vegetative height, specific leaf area and seed mass) to constraint a pool of environmentally filtered species from binary SDMs predictions. Results: We showed that all independent constraints expectedly contributed to reduce species richness overprediction. Only the "Probability ranking" rule allowed slightly but significantly improving predictions of community composition. Main conclusion: We tested various ways to implement the SESAM framework by integrating macroecological constraints into S-SDM predictions, and report one that is able to improve compositional predictions. We discuss possible improvements, such as further improving the causality and precision of environmental predictors, using other assembly rules and testing other types of ecological or functional constraints.

5C.09: Heritability of renal function parameters and electrolyte levels in the Swiss population

OBJECTIVE: Electrolytes handling by the kidney is essential for volume and blood pressure (BP) homeostasis but their distribution and heritability are not well described. We estimated the heritability of kidney function as well as of serum and urine concentrations, renal clearances and fractional excretions for sodium, chloride, potassium, calcium, phosphate and magnesium in a Swiss population-based study. DESIGN AND METHOD: Nuclear families were randomly selected from the general population in Switzerland. We estimated glomerular filtration rate (eGFR) using the CKD-EPI and MDRD equations. Urine was collected separately during day and night over 24-hour. We used the ASSOC program (S.A.G.E.) to estimate narrow sense heritability, including as covariates in the model: age, sex, body mass index and study center. RESULTS: The 1128 participants (537 men and 591 women from 273 families), had mean (sd) age of 47.4(17.5) years, body mass index of 25.0 (4.5) kg/m2 and CKD-EPI of 98.0(18.5) mL/min/1.73 m2. Heritability estimates (SE) were 46.0% (0.06), 48.0% (0.06) and 18.0% (0.06) for CKD-EPI, MDRD and 24-hour creatinine clearance (P < 0.05), respectively. Heritability [SE] of serum concentration was highest for calcium (37%[0.06]) and lowest for sodium (13%[0.05]). Heritabilities [SE] of 24-h urine concentrations and excretions, and of fractional excretions were highest for calcium (51%[0.06], 44%[0.06] and 51%[0.06], respectively) and lowest for potassium (11%[0.05], 10%[0.05] and 16%[0.06], respectively). All results were statistically different from zero.(Figure is included in full-text article.) CONCLUSIONS: : Serum and urine levels, urinary excretions and renal handling of electrolytes, particularly calcium, are heritable in the general adult population. Identifying genetic variants involved in electrolytes homeostasis may provide useful insight into the pathophysiological mechanisms involved in common chronic diseases such as kidney diseases, hypertension and diabetes.

Suodatuskalvojen toimivuuden arviointi paperiteollisuuden sovelluksissa

Työn tavoitteena oli etsiä vaihtoehtoja paperiteollisuuden kiertovesien ja pastapitoisten jätevesien suodatusprosesseissa tällä hetkellä käytössä oleville kalvoille. Työssä pyrittiin myös määrittämään tekijöitä, joiden avulla voitaisiin ennustaa polymeerikalvon käyttäytymistä erilaisissa paperiteollisuuden kalvosovelluksissa. Työn kirjallisessa osassa tarkasteltiin polymeerikalvojen ominaisuuksia, jotka vaikuttavat kalvojen käyttäytymiseen suodatusprosesseissa. Työssä esiteltiin myös tavallisimmat kalvomateriaalit ja polymeerikalvojen valmistustavat sekä paperiteollisuuden kalvosovelluksia. Paperiteollisuuden kalvosuodatussovellukset eroavat toisistaan huomattavasti toimintaolosuhteiltaan ja käyttötarkoituksiltaan. Tästä johtuen on hankalaa löytää yhteisiä tekijöitä, joiden perusteella voitaisiin ennustaa kalvon käyttäytymistä eri sovelluksissa. Kalvon hydrofiilisyyden todettiin kuitenkin vaikuttavan positiivisesti suodatustapahtumaan useissa sovelluksissa. Kokeellisessa osassa verrattiin erilaisten polymeerikalvojen ja referenssikalvojen toimintaa happaman kirkkaan suodoksen ja pastapitoisen veden suodatuksessa. Kirkkaan suodoksen suodatuskokeet tehtiin UPM-Kymmene Oy:n Kaukaan tehtailla. Pastapitoista jätevettä mallinnettiin syöttöpanoksilla, jotka tehtiin laimentamalla CTC:n valmistamaa LWC-pastaa. Suodatukset tehtiin CR 200/1- ja CR 550/10 -suodattimilla. Kirkkaan suodoksen suodatuksissa käytettiin referenssikalvona regeneroidusta selluloosasta ja pastapitoisen veden suodatuksessa aromaattisesta polyamidista valmistettua kalvoa. Kirkkaan suodoksen koesuodatusten perusteella todettiin, ettei minkään vertailtavan ultrasuodatuskalvon suodatuskapasiteetti ollut yhtä korkea kuin referenssikalvon. Referenssikalvon toiminta suodatuksessa oli myös vakaata syötön laadun muutoksista huolimatta. Todennäköisesti referenssikalvon erittäin hydrofiilinen luonne tekee siitä vertailtavia kalvoja sopivamman kirkkaan suodoksen suodatukseen. Pastapitoisen veden suodatustulosten perusteella referenssikalvolle löytyi useita potentiaalisia korvaajia. Näistä parhaan kalvon valitseminen edellyttää kuitenkin jatkotutkimuksia. SEM-analyysituloksista huomattiin, että tietyntyyppinen kalvorakenne parantaa kalvon toimintaa pastapitoisen veden suodatuksessa.

Hylky- ja vesijärjestelmän vaikutus kartongin tuotepuhtauteen

Kirjallisuusosassa käsitellään paperi- ja kartonkikoneiden eri vesijärjestelmiä, vedenkäytön vähentämistä ja sen vaikutusta prosessiin. Mikrobiologiaa, mikrobien aiheuttamia prosessiongelmia, mikrobien torjuntaa ja simulointia on myös käsitelty kirjallisuusosassa. Kokeellisessa osassa laadittiin Kartonkikone 1:n massa- ja vesijärjestelmän mikrobiologisen puhtauden simulointimalli Balas-prosessisimulointiohjelmalla. Kartongin mikrobiologinen puhtaus määritettiin kokonaispesäkelukuna. Kokeellinen osa sisälsi pilot-mittakaavan suodatinkoeajoja, joissa määritettiin tarvittavat erotusparametrit simulointimallille, selvitettiin Dynasand-hiekkasuodattimen soveltuvuus suihkuvesien puhdistukseen, Dynadisc-kiekkosuodattimen käyttökelpoisuus kiertoveden puhdistukseen kiertovesisuodattimena ja hiekkasuodattimien esisuodattimena sekä UV-reaktorin soveltuvuus suodatettujen vesien desifiointiin. Simulointimallilla tarkasteltiin eri prosessivaihtoehtojen vaikutus kartongin mikrobiologiseen puhtauteen. Suihkuvesien puhdistaminen hiekkasuodattimilla alentaa kokonaispesäkelukua vain vähän. Koneen ajettavuus paranee suihkuputkien roskaryöppyjen ja viiraosan limoittumisen vähenemisen takia. Kiertovesijärjestelmän pelkkä jakaminen hylkyprosessi- ja sakeudensäätövedeksi aiheuttaa kokonaispesäkeluvun kasvun prosessista poistettavien vesien puhdistumisen takia. Kokonaispesäkeluku minimoidaan poistamalla ylimääräinen vesi hylkysaostajan suodoksena. Suodatettua hylkysaostajan suodoksen ja viiraveden seosta käytetään sekä sakeudensäätö- että hylkyprosessivedeksi. Hylkymassalla on dominoiva vaikutus kokonaispesäkelukuun. Suurin vähennys kokonaispesäkeluvussa saadaan estämällä mikrobikasvu hylkymassassa. Tämä voidaan tehdä kuumentamalla hylkymassa 80 °C:n höyryllä. Suodatuskoeajojen perusteella Dynasand-hiekkasuodattimella voidaan puhdistaa pisaralämmönvaihtimelta saatavaa lämmintä suihkuvettä. Esisuodatettua kiertovettä voidaan puhdistaa Dynasand-hiekkasuodattimella viiran johtotelojen suihkuvedeksi. Dynadisc-kiekkosuodatinta voidaan käyttää hiekkasuodattimen esisuodattimena ja kiertovesisuodattimena. UV-säteily poistaa tehokkaasti mikrobeja suodatetuista vesistä.

Pigmenttien suodatus

Työn tavoitteena oli tutkia neljän eri koesuotimen soveltuvuutta pigmenttilietteen kiintoainepitoisuuden nostoon. Työssä käytetyt suotimet olivat Larox PF 0,1, Certus-CU-0047, Crossflow-koesuodin ja Steuerung ET06-linko. Suodinväliaineena Larox PF 0,1-suotimessa ja Crossflow-koesuotimessa käytettiin Tamfelt Oyj:n suodinkankaita. Certus-CU-0047-suotimessa suodinväliaineena toimi keraaminen membraani. Työn kirjallisuusosassa tarkasteltiin partikkelien karakterisointia, suodatuksen teoriaa, kakkusuodatusta, suodinväliaineista suodinkankaita ja membraaneja. Lisäksi tarkasteltiin paperin päällystämiseen käytettyjen pigmenttien ominaisuuksia ja niiden suodatusta. Kokeet suoritettiin Larox PF 0,1, Certus-CU-0047 ja Crossflow-koesuotimella vakiopainesuodatuksena yhdellä paineella. Steuerung ET06-lingon kokeet suoritettiin vakiovirtaussuodatuksena käyttäen kolmea eri virtausnopeutta ja kolmea eri lingon ja ruuvin kierrossuhdetta. Työssä suodatettiin neljää erilaista pigmenttilietettä. Suodoksista otettiin näytteitä niiden sameuden määrittämiseksi. Larox Pf 0,1-suotimella ja Steuerung ET06-dekantterilingolla saatiin nostettua pigmenttilietteen kiintoainepitoisuutta erittäin hyvin. Loput kaksi suodinta eivät sovellu tähän tarkoitukseen ollenkaan. Vakiopainesuodatuksissa suodatusajat muodostuivat kuitenkin liian pitkiksi. Suodoksien kiintoainepitoisuudet olivat suurimmaksi osaltaan pieniä lukuun ottamatta tiettyjä suodinkankaita. Lietteen 2 kiintoainepitoisuuden nostaminen oli kaikilla suotimilla erittäin vaikeaa, muut lietteet suodattuivat kohtuullisen hyvin. Näiden kokeiden perusteella voidaan sanoa, että varsinkin vakiovirtaussuodatus soveltuu hyvin ainakin tiettyjen pigmenttilietteiden kiintoainepitoisuuden nostoon.

Serum 25-hydroxyvitamin D level and kidney function decline in a Swiss general adult population.

Molecular evidence suggests that levels of vitamin D are associated with kidney function loss. Still, population-based studies are limited and few have considered the potential confounding effect of baseline kidney function. This study evaluated the association of serum 25-hydroxyvitamin D with change in eGFR, rapid eGFR decline, and incidence of CKD and albuminuria. Baseline (2003-2006) and 5.5-year follow-up data from a Swiss adult general population were used to evaluate the association of serum 25-hydroxyvitamin D with change in eGFR, rapid eGFR decline (annual loss >3 ml/min per 1.73 m(2)), and incidence of CKD and albuminuria. Serum 25-hydroxyvitamin D was measured at baseline using liquid chromatography-tandem mass spectrometry. eGFR and albuminuria were collected at baseline and follow-up. Multivariate linear and logistic regression models were used considering potential confounding factors. Among the 4280 people included in the analysis, the mean±SD annual eGFR change was -0.57±1.78 ml/min per 1.73 m(2), and 287 (6.7%) participants presented rapid eGFR decline. Before adjustment for baseline eGFR, baseline 25-hydroxyvitamin D level was associated with both mean annual eGFR change and risk of rapid eGFR decline, independently of baseline albuminuria. Once adjusted for baseline eGFR, associations were no longer significant. For every 10 ng/ml higher baseline 25-hydroxyvitamin D, the adjusted mean annual eGFR change was -0.005 ml/min per 1.73 m(2) (95% confidence interval, -0.063 to 0.053; P=0.87) and the risk of rapid eGFR decline was null (odds ratio, 0.93; 95% confidence interval, 0.79 to 1.08; P=0.33). Baseline 25-hydroxyvitamin D level was not associated with incidence of CKD or albuminuria. The association of 25-hydroxyvitamin D with eGFR decline is confounded by baseline eGFR. Sufficient 25-hydroxyvitamin D levels do not seem to protect from eGFR decline independently from baseline eGFR.

Glyoxysomal malate-dehydrogenase and malate synthase from Soybean cotyledons (Glycine max. L.): Enzyme association, antibody-production and cDNA cloning

In order to investigate a possible association between soybean malate synthase (MS; L-malate glyoxylate-lyase, CoA-acetylating, EC 4.1.3.2) and glyoxysomal malate dehydrogenase (gMDH; (S)-malate: NAD(+) oxidoreductase, EC 1.1.1.37), two consecutive enzymes in the glyoxylate cycle, their elution profiles were analyzed on Superdex 200 HR fast protein liquid chromatography columns equilibrated in low- and high-ionic-strength buffers. Starting with soluble proteins extracted from the cotyledons of 5-d-old soybean seedlings and a 45% ammonium sulfate precipitation, MS and gMDH coeluted on Superdex 200 HR (low-ionic-strength buffer) as a complex with an approximate relative molecular mass (M(r)) of 670000. Dissociation was achieved in the presence of 50 mM KCl and 5 mM MgCl2, with the elution of MS as an octamer of M, 510 000 and of gMDH as a dimer of M, 73 000. Polyclonal antibodies raised to the native copurified enzymes recognized both denatured MS and gMDH on immunoblots, and their native forms after gel filtration. When these antibodies were used to screen a lambda ZAP II expression library containing cDNA from 3-d-old soybean cotyledons, they identified seven clones encoding gMDH, whereas ten clones encoding MS were identified using an antibody to SDS-PAGE-purified MS. Of these cDNA clones a 1.8 kb clone for MS and a 1.3-kb clone for gMDH were fully sequenced. While 88% identity was found between mature soybean gMDH and watermelon gMDH, the N-terminal transit peptides showed only 37% identity. Despite this low identity, the soybean gMDH transit peptide conserves the consensus R(X(6))HL motif also found in plant and mammalian thiolases.

AA amyloidosis treated with tocilizumab: case series and updated literature review.

BACKGROUND: In published case reports, tocilizumab (TCZ) has shown good efficacy for AA amyloidosis in almost all patients. We investigated the efficacy and safety of TCZ in AA amyloidosis in a multicentre study of unselected cases. METHODS: We e-mailed rheumatology and internal medicine departments in France, Switzerland and North Africa by using the Club Rhumatismes Inflammation (CRI) network and the French TCZ registry, Registry RoAcTEmra (REGATE), to gather data on consecutive patients with histologically proven AA amyloidosis who had received at least one TCZ infusion. Efficacy was defined as a sustained decrease in proteinuria level and/or stable or improved glomerular filtration rate (GFR) and by TCZ maintenance. RESULTS: We collected 12 cases of AA amyloidosis treated with TCZ as monotherapy (mean age of patients 63 ± 16.2 years, amyloidosis duration 20.6 ± 31.3 months): eight patients had rheumatoid arthritis (RA), six with previous failure of anti-tumor necrosis factor α (anti-TNF-α) therapy. In total, 11 patients had renal involvement, with two already on hemodialysis (not included in the renal efficacy assessment). For the nine other patients, baseline GFR and proteinuria level were 53.6 ± 32.8 mL/min and 5 ± 3.3 g/24 h, respectively. The mean follow-up was 13.1 ± 11 months. TCZ was effective for six of the eight RA patients (87.5%) according to European League Against Rheumatism response criteria (four good and two moderate responders). As expected, C-reactive protein (CRP) level decreased with treatment for 11 patients. Renal amyloidosis (n = 9) progressed in three patients and was stabilized in three. Overall, three patients showed improvement, with sustained decrease in proteinuria level (42%, 82% and 96%). Baseline CRP level was higher in subsequent responders to TCZ than other patients (p = 0.02). Among the six RA patients with previous anti-TNF-α therapy, amyloidosis was ameliorated in one and stabilized in three. Three serious adverse events occurred (two diverticulitis and one major calciphylaxia due to renal failure). Finally, 7 of 12 (58%) patients continued TCZ. CONCLUSIONS: The efficacy of TCZ for AA amyloidosis varies depending on the inflammatory status at treatment onset. Discrepancies between our study of unselected consecutive patients and reported cases may be due to publication bias. These results support further prospective trials of TCZ for AA amyloidosis.

Microtubule Associated Protein 1b (MAP1B) Is a Marker of the Microtubular Cytoskeleton in Podocytes but Is Not Essential for the Function of the Kidney Filtration Barrier in Mice.

Podocytes are essential for the function of the kidney glomerular filter. A highly differentiated cytoskeleton is requisite for their integrity. Although much knowledge has been gained on the organization of cortical actin networks in podocyte's foot processes, less is known about the molecular organization of the microtubular cytoskeleton in primary processes and the cell body. To gain an insight into the organization of the microtubular cytoskeleton of the podocyte, we systematically analyzed the expression of microtubule associated proteins (Maps), a family of microtubules interacting proteins with known functions as regulator, scaffold and guidance proteins. We identified microtubule associated protein 1b (MAP1B) to be specifically enriched in podocytes in human and rodent kidney. Using immunogold labeling in electron microscopy, we were able to demonstrate an enrichment of MAP1B in primary processes. A similar association of MAP1B with the microtubule cytoskeleton was detected in cultured podocytes. Subcellular distribution of MAP1B HC and LC1 was analyzed using a double fluorescent reporter MAP1B fusion protein. Subsequently we analyzed mice constitutively depleted of MAP1B. Interestingly, MAP1B KO was not associated with any functional or structural alterations pointing towards a redundancy of MAP proteins in podocytes. In summary, we established MAP1B as a specific marker protein of the podocyte microtubular cytoskeleton.

Antireflection coatings from analogy between electron scattering and spin precession

We use the analogy between scattering of a wave from a potential, and the precession of a spin-half particle in a magnetic field, to gain insight into the design of an antireflection coating for electrons in a semiconductor superlattice. It is shown that the classic recipes derived for optics are generally not applicable due to the different dispersion law for electrons. Using the stability conditions we show that a Poisson distribution of impedance steps is a better approximation than is a Gaussian distribution. Examples are given of filters with average transmissivity exceeding 95% over an allowed band.

Regenerated cellulose ultrafiltration membranes in the treatment of pulp and paper mill process waters

Ultrafiltration (UF) is widely applied in different separation processes in the pulp and paper industry. The growing need to protect the environment, a lack of pure water and an interest in producing high-value chemicals from compounds present in process waters will probably lead to an increase in the use of UF in the pulp and paper industry. The efficiency and cost-effectiveness of a UF process depends on the applied membrane. The membrane should have a high and stable filtration capacity, a particular selectivity and a long operational lifetime. To meet these requirements a membrane should have a low fouling tendency. In addition, it should withstand the prevailing operational and chemical conditions. This thesis evaluates the performance and applicability of the regenerated cellulose (RC) membranes 00030T and C2 in the treatment of pulp and paper mill process waters based on the requirements above. The results demonstrated that both the tested RC membranes fulfilled well the requirement of high filtration capacity. In addition, in the filtration of a paper mill clear filtrate (CF) the RC membranes were not as greatly affected by variations in the CF quality as a polysulphone membrane. Furthermore, due to their extreme hydrophilicity and weak charge the fouling tendency of the membranes can be expected to be low in pulp and paper mill filtration applications. It is, however, known that fouling cannot be totally avoided even when the membrane is chosen very carefully. This study indicated that carbohydrates influenced negatively on permeability and caused fouling in the filtration of groundwood mill circulation water. Thus, a pre-treatment effectively reducing the amount of carbohydrates might help to maintain a stable capacity. However, the results of the thesis also showed that the removal of some of the possible foulants might just increase the harmful effect of others. Multivariate examination was useful in the understanding of the complicated factors causing the unstable capacity. The thesis also revealed that the 00030T and C2 membranes can be used at high pressure (max. tested pressure 12 bar). The C2 membrane, having a sponge-like substructure, was more pressure resistant, and its performance was more stable at high pressure compared to the UCO30T membrane containing macrovoids in its substructure. Both tested membranes can, according to the results, also be used at temperatures as high as 70°C in acidic, neutral and alkaline conditions. However, the use at extreme conditions might cause faster ageing of the membranes compared to ageing in neutral conditions. The thesis proved that both the tested RC membranes are very suitable for pulp and paper mill applications and that the membranes can be utilised in processes operating in challenging conditions. Thus, they could be used in more demanding applications than supposed earlier.

Predicting richness and composition in mountain insect communities at high resolution: a new test of the SESAM framework

Aim The aim of this study was to test different modelling approaches, including a new framework, for predicting the spatial distribution of richness and composition of two insect groups. Location The western Swiss Alps. Methods We compared two community modelling approaches: the classical method of stacking binary prediction obtained fromindividual species distribution models (binary stacked species distribution models, bS-SDMs), and various implementations of a recent framework (spatially explicit species assemblage modelling, SESAM) based on four steps that integrate the different drivers of the assembly process in a unique modelling procedure. We used: (1) five methods to create bS-SDM predictions; (2) two approaches for predicting species richness, by summing individual SDM probabilities or by modelling the number of species (i.e. richness) directly; and (3) five different biotic rules based either on ranking probabilities from SDMs or on community co-occurrence patterns. Combining these various options resulted in 47 implementations for each taxon. Results Species richness of the two taxonomic groups was predicted with good accuracy overall, and in most cases bS-SDM did not produce a biased prediction exceeding the actual number of species in each unit. In the prediction of community composition bS-SDM often also yielded the best evaluation score. In the case of poor performance of bS-SDM (i.e. when bS-SDM overestimated the prediction of richness) the SESAM framework improved predictions of species composition. Main conclusions Our results differed from previous findings using community-level models. First, we show that overprediction of richness by bS-SDM is not a general rule, thus highlighting the relevance of producing good individual SDMs to capture the ecological filters that are important for the assembly process. Second, we confirm the potential of SESAM when richness is overpredicted by bS-SDM; limiting the number of species for each unit and applying biotic rules (here using the ranking of SDM probabilities) can improve predictions of species composition