40 K Liquid Neon Energy Storage Unit

A thermal Energy Storage Unit (ESU) could be used to attenuate inherent temperature fluctuations of a cold finger, either from a cryocooler working or due to sudden income heat bursts. An ESU directly coupled to the cold source acts as a thermal buffer temporarily increasing its cooling capacity and providing a better thermal stability of the cold finger (“Power Booster mode”). The energy storage units presented here use an enthalpy reservoir based on the high latent heat of the liquid-vapour transition of neon in the temperature range 38 - 44 K to store up to 900 J, and that uses a 6 liters expansion volume at RT in order to work as a closed system. Experimental results in the power booster mode will be described: in this case, the liquid neon cell was directly coupled to the cold finger of the working cryocooler, its volume (12 cm3) allowing it to store 450 J at around 40 K. 10 W heat bursts were applied, leading to liquid evaporation, with quite reduced temperature changes. The liquid neon reservoir can also work as a temporary cold source to be used after stopping the cryocooler, allowing for a vibration-free environment. In this case the enthalpy reservoir implemented (24 cm3) was linked to the cryocooler cold finger through a gas gap heat switch for thermal coupling/decoupling of the cold finger. We will show that, by controlling the enthalpy reservoir’s pressure, 900 J can be stored at a constant temperature of 40 K as in a triple-point ESU.

40 K Neon liquid energy storage unit

Cryocoolers have been progressively replacing the use of the stored cryogens in cryogenic chains used for detector cooling, thanks to their higher and higher reliability. However, the mechanical vibrations, the electromagnetic interferences and the temperature fluctuations inherent to their functioning could reduce the sensor’s sensitivity. In order to minimize this problem, compact thermal energy storage units (ESU) are studied, devices able to store thermal energy without significant temperature increase. These devices can be used as a temporary cold source making it possible to turn the cryocooler OFF providing a proper environment for the sensor. A heat switch is responsible for the thermal decoupling of the ESU from the cryocooler’s temperature that increases when turned OFF. In this work, several prototypes working around 40 K were designed, built and characterized. They consist in a low temperature cell that contains the liquid neon connected to an expansion volume at room temperature for gas storage during the liquid evaporation phase. To turn this system insensitive to the gravity direction, the liquid is retained in the low temperature cell by capillary effect in a porous material. Thanks to pressure regulation of the liquid neon bath, 900 J were stored at 40K. The higher latent heat of the liquid and the inexistence of triple point transitions at 40 K turn the pressure control during the evaporation a versatile and compact alternative to an ESU working at the triple point transitions. A quite compact second prototype ESU directly connected to the cryocooler cold finger was tested as a temperature stabilizer. This device was able to stabilize the cryocooler temperature ((≈ 40K ±1 K) despite sudden heat bursts corresponding to twice the cooling power of the cryocooler. This thesis describes the construction of these devices as well as the tests performed. It is also shown that the thermal model developed to predict the thermal behaviour of these devices, implemented as a software,describes quite well the experimental results. Solutions to improve these devices are also proposed.

Analysis and visualization of energy use for university campus

The reduction of greenhouse gas emissions is one of the big global challenges for the next decades due to its severe impact on the atmosphere that leads to a change in the climate and other environmental factors. One of the main sources of greenhouse gas is energy consumption, therefore a number of initiatives and calls for awareness and sustainability in energy use are issued among different types of institutional and organizations. The European Council adopted in 2007 energy and climate change objectives for 20% improvement until 2020. All European countries are required to use energy with more efficiency. Several steps could be conducted for energy reduction: understanding the buildings behavior through time, revealing the factors that influence the consumption, applying the right measurement for reduction and sustainability, visualizing the hidden connection between our daily habits impacts on the natural world and promoting to more sustainable life. Researchers have suggested that feedback visualization can effectively encourage conservation with energy reduction rate of 18%. Furthermore, researchers have contributed to the identification process of a set of factors which are very likely to influence consumption. Such as occupancy level, occupants behavior, environmental conditions, building thermal envelope, climate zones, etc. Nowadays, the amount of energy consumption at the university campuses are huge and it needs great effort to meet the reduction requested by European Council as well as the cost reduction. Thus, the present study was performed on the university buildings as a use case to: a. Investigate the most dynamic influence factors on energy consumption in campus; b. Implement prediction model for electricity consumption using different techniques, such as the traditional regression way and the alternative machine learning techniques; and c. Assist energy management by providing a real time energy feedback and visualization in campus for more awareness and better decision making. This methodology is implemented to the use case of University Jaume I (UJI), located in Castellon, Spain.

40 K neon liquid energy storage unit

Cryocoolers have been progressively replacing the use of the stored cryogens in cryogenic chains used for detector cooling, thanks to their higher and higher reliability. However, the mechanical vibrations, the electromagnetic interferences and the temperature fluctuations inherent to their functioning could reduce the sensor’s sensitivity. In order to minimize this problem, compact thermal energy storage units (ESU) are studied, devices able to store thermal energy without significant temperature increase. These devices can be used as a temporary cold source making it possible to turn the cryocooler OFF providing a proper environment for the sensor. A heat switch is responsible for the thermal decoupling of the ESU from the cryocooler’s temperature that increases when turned OFF. In this work, several prototypes working around 40 K were designed, built and characterized. They consist in a low temperature cell that contains the liquid neon connected to an expansion volume at room temperature for gas storage during the liquid evaporation phase. To turn this system insensitive to the gravity direction, the liquid is retained in the low temperature cell by capillary effect in a porous material. Thanks to pressure regulation of the liquid neon bath, 900 J were stored at 40K. The higher latent heat of the liquid and the inexistence of triple point transitions at 40 K turn the pressure control during the evaporation a versatile and compact alternative to an ESU working at the triple point transitions. A quite compact second prototype ESU directly connected to the cryocooler cold finger was tested as a temperature stabilizer. This device was able to stabilize the cryocooler temperature ((≈ 40K ±1 K) despite sudden heat bursts corresponding to twice the cooling power of the cryocooler. This thesis describes the construction of these devices as well as the tests performed. It is also shown that the thermal model developed to predict the thermal behaviour of these devices,implemented as a software, describes quite well the experimental results. Solutions to improve these devices are also proposed.

A piezoelectric based energy harvester interface for a CMOS wireless sensor IC

In this thesis a piezoelectric energy harvesting system, responsible for regulating the power output of a piezoelectric transducer subjected to ambient vibration, is designed to power an RF receiver with a 6 mW power consump-tion. The electrical characterisation of the chosen piezoelectric transducer is the starting point of the design, which subsequently presents a full-bridge cross-coupled rectifier that rectifies the AC output of the transducer and a low-dropout regulator responsible for delivering a constant voltage system output of 0.6 V, with low voltage ripple, which represents the receiver’s required sup-ply voltage. The circuit is designed using CMOS 130 nm UMC technology, and the system presents an inductorless architecture, with reduced area and cost. The electrical simulations run for the complete circuit lead to the conclusion that the proposed piezoelectric energy harvesting system is a plausible solution to power the RF receiver, provided that the chosen transducer is subjected to moderate levels of vibration.

Design of a low-voltage CMOS RF receiver for energy harvesting sensor node

In this thesis a CMOS low-power and low-voltage RF receiver front-end is presented. The main objective is to design this RF receiver so that it can be powered by a piezoelectric energy harvesting power source, included in a Wireless Sensor Node application. For this type of applications the major requirements are: the low-power and low-voltage operation, the reduced area and cost and the simplicity of the architecture. The system key blocks are the LNA and the mixer, which are studied and optimized with greater detail, achieving a good linearity, a wideband operation and a reduced introduction of noise. A wideband balun LNA with noise and distortion cancelling is designed to work at a 0.6 V supply voltage, in conjunction with a double-balanced passive mixer and subsequent TIA block. The passive mixer operates in current mode, allowing a minimal introduction of voltage noise and a good linearity. The receiver analog front-end has a total voltage conversion gain of 31.5 dB, a 0.1 - 4.3 GHz bandwidth, an IIP3 value of -1.35 dBm, and a noise figure lower than 9 dB. The total power consumption is 1.9 mW and the die area is 305x134.5 m2, using a standard 130 nm CMOS technology.

Starburst accelerator and incubator construction & energy: How to monitor the activities of an incubator and give strategic advice to startups

This work project takes the format of a problem-solving approach suggested by “Impulse Partners”, a French consulting firm. It recommends a way to measure the success of ten startups in the incubators “Starburst” and “Incubator Construction & Energy” and give them strategic guidance. A Balanced Scorecard is elaborated to help incubated startups building up and implementing their strategy. The Scorecard suggests possible initiatives for the startups that are ideally realized with the help of the consulting firm that is steering the incubator. Special attention is drawn to what the startups need to succeed, which typically concerns financing, networking and managing skills.

Trauma and envenoming caused by stingrays and other fish in a fishing community in Pontal do Paranapanema, state of São Paulo, Brazil: epidemiology, clinical aspects, and therapeutic and preventive measures

INTRODUCTION: Accidents caused by fish are common in inland fishing communities in Brazil, being work-related injuries in the majority of cases. These populations have no information on the mechanisms of trauma or envenoming. METHODS: Through a questionnaire administered to fishermen, we obtained clinical and epidemiological data on accidents in Rosana, Pontal do Paranapanema, State of São Paulo, Brazil. These data were analyzed and converted into an easily understood prevention and treatment program for the colony. RESULTS: Thirty-nine fishermen replied to the survey. All of the patients had been hurt by fish. Of those mentioned, the yellow catfish (Pimelodus maculatus) was the main fish species associated with injuries, but others also caused trauma to the fishermen. Six fishermen had been envenomed by stingrays. Pain and ulcers were the main symptoms and were described as intolerable. Approximately half of those injured were treated using traditional folk remedies. CONCLUSIONS: The fishermen suffered multiple accidents with catfish, which are venomous and cause intense pain, as well as trauma due to other fish, such as surubins, traíras, freshwater croakers, and piranhas. Approximately 16% of those interviewed presented with envenomation from stingrays. Our data and previous experience in the area led to the creation of a pamphlet with clear language that can effectively help fishermen in the region, an area in need of health services and disease prevention. This initiative also applies to the whole La Plata River basin, which has similar fauna.

Simplified wind turbine models for wind energy integration into power systems

This paper analyses the boundaries of simplified wind turbine models used to represent the behavior of wind turbines in order to conduct power system stability studies. Based on experimental measurements, the response of recent simplified (also known as generic) wind turbine models that are currently being developed by the International Standard IEC 61400-27 is compared to complex detailed models elaborated by wind turbine manufacturers. This International Standard, whose Technical Committee was convened in October 2009, is focused on defining generic simulation models for both wind turbines (Part 1) and wind farms (Part 2). The results of this work provide an improved understanding of the usability of generic models for conducting power system simulations.

Evaluation of preventive measures for mother-to-child transmission of HIV in Aracaju, State of Sergipe, Brazil

INTRODUCTION: The main route of human immunodeficiency virus (HIV) infection in children is from mother to child. The preventive measures established for the Aids Clinical Trial Group protocol 076 (ACTG 076) significantly reduces HIV vertical transmission rates. This study aims to evaluate the implementation of the ACTG 076 protocol in the maternity units of State of Sergipe, Brazilian northeast. METHODS: This is a descriptive, retrospective study with a quantitative approach, with HIV positive women and children exposed, attending a Maternity reference for high-risk pregnancies. Data were obtained from patient records registered in the years 1994 to 2010. RESULTS: Amongst the 110 pregnant women and exposed newborns, the ACTG 076 protocol was fully utilized in only 31.8% of the participants. During the prenatal period, zidovudine (ZDV) was taken by 79.1% of the pregnant women. Only 49.1% of HIV seropositive patients used ZDV during delivery. Two (1.8%) children were considered infected and 50 (45.5%) do not have a conclusive diagnosis to date. CONCLUSIONS: There were significant deficiencies in the prevention of mother-to-child transmission of HIV, including lack of compliance with the three phases of the ACTG 076 protocol; inadequacies in prenatal care; inappropriate mode of delivery and lack of adequate follow up of exposed children.

Post-merger innovative performance in the renewable energy sector

Due to global warming and shrinking fossil fuel resources, politics as well as society urge for a reduction of green house gas (GHG) emissions. This leads to a re-orientation towards a renewable energy sector. In this context, innovation and new technologies are key success factors. Moreover, the renewable energy sector has entered a consolidation stage, where corporate investors and mergers and acquisitions (M&A) gain in importance. Although both M&A and innovation in the renewable energy sector are important corporate strategies, the link between those two aspects has not been examined before. The present thesis examines the research question how M&A influence the acquirer’s post-merger innovative performance in the renewable energy sector. Based on a framework of relevant literature, three hypotheses are defined. First, the relation between non-technology oriented M&A and post-merger innovative performance is discussed. Second, the impact of absolute acquired knowledge on postmerger innovativeness is examined. Third, the target-acquirer relatedness is discussed. A panel data set of 117 firms collected over a period of six years has been analyzed via a random effects negative binomial regression model and a time lag of one year. The results support a non-significant, negative impact of non-technology M&A on postmerger innovative performance. The applied model did not support a positive and significant impact of absolute acquired knowledge on post-merger innovative performance. Lastly, the results suggest a reverse relation than postulated by Hypothesis 3. Targets from the same industry significantly and negatively influence the acquirers’ innovativeness.

Infraventus-internationalizing a renewables business to Kenya

Infraventus – Internationalizing a Renewables Business to Kenya Infraventus is a renewable energy development company, with a consolidated experience, since 1988, in developing, constructing and operating projects mainly in Portugal, but also in other countries: Spain, Poland, France, Australia, Finland and Panama, and is now regarding Kenya as a possible destiny. Kenya is the biggest economy of East Africa, with a growing GDP around 5% and a low level of electric grid coverage thru its territory, 33% of national access to electricity. Kenya energy policy is intended to promote the investment in renewables; wind and sun are existing resources in good measures. Kenya is an interesting destiny to Infraventus, but has many risks. The objective of this dissertation is to evaluate the possible advantages of this investment and risks and propose recommendations about how to mitigate them considering alternative entry mode

Inclusion of disabled people in siemens AG'S energy management division

This work project is a business plan for a project regarding corporate social entrepreneurship that will be developed by Siemens Switchboard Factory in Corroios. The main purpose of this project is to understand the viability of a partnership between Siemens AG’s and CERCISA in order to include disabled people into Siemens AG’s Energy Management Division, with the goal of achieving social and economic impact by insources activities while complying with the law1. The produced output, a business plan, aims to study and understand the practical suitability and feasibility of the concepts and propose a sustainable project that can be replicated, starting with a pilot testing and validation period.

Evaluation of preventative and control measures for congenital syphilis in State of Mato Grosso

Introduction Congenital syphilis is an important health problem in Brazil. This study assessed measures aimed at the prevention and control of syphilis in the State of Mato Grosso and its capital, Cuiabá. Methods A descriptive study cross-sectional and of time trends assessing the congenital syphilis was performed in Cuiabá and Mato Grosso between 2001 and 2011. We compared maternal sociodemographic characteristics and health care utilization related to cases of congenital syphilis during the periods from 2001 to 2006 and from 2007 to 2011. We assessed the temporal trends in this disease's incidence using a simple linear regression. Results Between 2001 and 2006 in Mato Grosso, 86.8% of the mothers who had live births with congenital syphilis received prenatal care, 90.6% presented with a nontreponemal test reagent at delivery, 96.2% had no information regarding a treponemal confirmatory test at delivery, and 77.6% received inadequate treatment for syphilis; additionally, 75.8% of their partners were not treated. There was a statistically significant reduction in prenatal visits (p = 0.004) and an increase in the proportion of mothers reactive to nontreponemal tests at delivery (p = 0.031) between the two periods. No other variables were found to differ significantly between the periods. In Cuiabá, we observed a similar distribution of variables. In the state and in the capital, the increasing trend of congenital syphilis was not statistically significant. Conclusions The high incidence of congenital syphilis in Mato Grosso and the low levels of health care indicators for pregnant women with syphilis suggest the need to improve the coverage and quality of prenatal care.

Energy efficiency in energy policy: Empirical evidence of direct rebound effect in Portuguese household's demand for electricity

This project the direct rebound effect for the electricity demand in Portugal. While we find evidence of such an effect, the estimations also reflect the institutional arrangement that has characterized the electricity market in the country. Also, issues related to energy efficiency promotion are addressed in general putting into context the case study developed.