Anomalous re-entrant glassy magnetic phase in LaMn0.5Co0.5O3 single crystals

We report an anomalous re-entrant glassy magnetic phase in (l00) oriented ferromagnetic LaMn0.5Co0.5O3 single crystals. The characterization is fortified with conventional magnetometry, like linear as-well-as non-linear ac susceptibility and specific heat. As the sample is cooled below the ferromagnetic transition temperature, it reenters a glassy magnetic phase whose dynamics have little resemblance with the conventional response. The glassy transition shifts to a higher temperature with increasing frequency of the applied ac field. But it does not respond to the dc biasing or memory experiment. Specific heat as well as non-linear ac susceptibility data also do not relate to the conventional glassy response. Unusually low magnetic entropy indicates the lack of long range magnetic ordering. The results demonstrate that the glassy phase in LaMn0.5Co0.5O3 is not due to any of the known conventional origins. We infer that the competing ferromagnetic and antiferromagnetic interaction due to high B-site disorder is responsible for this anomalous re-entrant glassy phase. (C) 2016 AIP Publishing LLC.

Three-Dimensional Modeling of Heat Transfer and Fluid Flow in Laminar-Plasma Material Re-Melting Processing

Modeling study is performed concerning the heat transfer and fluid flow for a laminar argon plasma jet impinging normally upon a flat workpiece exposed to the ambient air. The diffusion of the air into the plasma jet is handled by using the combined-diffusion-coefficient approach. The heat flux density and jet shear stress distributions at the workpiece surface obtained from the plasma jet modeling are then used to study the re-melting process of a carbon steel workpiece. Besides the heat conduction within the workpiece, the effects of the plasma-jet inlet parameters (temperature and velocity), workpiece moving speed, Marangoni convection, natural convection etc. on the re-melting process are considered. The modeling results demonstrate that the shapes and sizes of the molten pool in the workpiece are influenced appreciably by the plasma-jet inlet parameters, workpiece moving speed and Marangoni convection. The jet shear stress manifests its effect at higher plasma-jet inlet velocities, while the natural convection effect can be ignored. The modeling results of the molten pool sizes agree reasonably with available experimental data.

Theoretical simulation studies of pulsed field magnetisation of (RE)BCO bulk superconductors

The magnetisation of bulk high temperature superconductors (HTS), such as RE-Ba-Cu-O [(RE)BCO, where RE is a rare earth element or Y], by a practical technique is essential for their application in high field, permanent magnet-like devices. Research to-date into the pulsed field magnetisation (PFM) of these materials, however, has been limited generally to experimental techniques, with relatively little progress in the development of theoretical models. This is because not only is a multi-physics approach needed to take account of the heating of the samples but also the high electric fields generated are well above the regime in which there are reliable experimental results. This paper describes a framework of theoretical simulation using the finite element method (FEM) that is applicable to both single- and multi-pulse magnetisation processes of (RE)BCO bulk superconductors. The model incorporates the heat equation and provides a convenient way of determining the distribution of trapped field, current density and temperature change within a bulk superconductor at each stage of the magnetisation process. An example of the single-pulse magnetisation of a (RE)BCO bulk is described. Potentially, the model may serve as a cost-effective tool for the optimisation of the bulk geometry and the magnetisation profile in multi-pulse magnetisation processes. © 2010 IOP Publishing Ltd.

Temperature Dependence of the Tribological Properties of Laser Re-Melted Al-Cu-Fe Quasicrystalline Plasma Sprayed Coatings

The aim of this study was to investigate the effect of temperature on tribological properties of plasma-sprayed Al-Cu-Fe quasicrystal (QC) coating after laser re-melting treatment. The laser treatment resulted in a more uniform, denser and harder microstructure than that of the as-sprayed coatings. Tribological experiments on the coatings were conducted under reciprocating motion at high frequency in the temperature range from 25 to 650 degreesC. Remarkable influence of temperature on the friction behavior of the coating was recorded and analyzed. Microstructural analysis indicated that the wear mechanisms of the re-melted QC coatings changed from abrasive wear at room temperature, to adhesive wear at 400 degreesC and severe adhesive wear at 650 degreesC owing to the material transfer of the counterpart ball. It was also observed that the ratio of the icosahedral (i)-phase to beta-Al-50(Fe,CU)(50) phase in the coating was higher after test at 400 'C than that at 650 'C. The variation of the ratio UP of coating and of the property of the counterpart ball and coating with the temperature are the two main factors influencing the wear mechanisms and value of the friction coefficient.

Análisis económico de experimentos agrícolas con presupuestos parciales: Re-enseñando el uso de este enfoque

Se presenta la metodología de presupuestos parciales como método de análisis económico de experimentos agrícolas y se analizan algunas inconsistencias encontradas en la misma. Tales inconsistencias incluyen: la implementación del análisis cuando el ANAVA no presenta diferencias estadísticas entre tratamientos, y la ejecución del mismo sin considerar la naturaleza de los tratamientos. Otras inconsistencias adicionales, son la conducción de los análisis sin usar precios de campo, llegar a conclusiones sobre el tratamiento más rentable sin usar ninguna tasa núnima de retomo, generar una recomendación a partir de un solo experimento, analizar los datos sin corregir los rendimientos experimentales, y estimar los costos a partir de la información del experimento. En este escrito no se busca reinventar el enfoque de presupuestos parciales, en su lugar se busca reenseñar su uso. Para ello, inicialmente se hace una exposición de cuando se debe usar el enfoque, luego a manera de algoritmo, se enumeran los pasos que se deben seguir para hacer un análisis económico siguiendo este método. Se continua con una discusión sobre la relación entre presupuestos parciales y optimización de funciones de producción. Finalmente, se presentan un caso de análisis

低Re数偏心圆柱间定常整流流动

本文研究低雷诺数情况下偏心圆柱间定常Streaming流动问题,其中内柱以速度U(x)cosωt在静止不可压粘性流体中作小振幅直线简谐振动,外柱则固定不动。

De re etymologica: vasc. -(r)antz ‘hacia’

Iker bilduma = Colección Iker, nº 17