Utilization of a Time Domain Simulator in the Technical and Economic Analysis of a Wind Turbine Electric Drive Train

The amount of installed wind power has been growing exponentially during the past ten years. As wind turbines have become a significant source of electrical energy, the interactions between the turbines and the electric power network need to be studied more thoroughly than before. Especially, the behavior of the turbines in fault situations is of prime importance; simply disconnecting all wind turbines from the network during a voltage drop is no longer acceptable, since this would contribute to a total network collapse. These requirements have been a contributor to the increased role of simulations in the study and design of the electric drive train of a wind turbine. When planning a wind power investment, the selection of the site and the turbine are crucial for the economic feasibility of the installation. Economic feasibility, on the other hand, is the factor that determines whether or not investment in wind power will continue, contributing to green electricity production and reduction of emissions. In the selection of the installation site and the turbine (siting and site matching), the properties of the electric drive train of the planned turbine have so far been generally not been taken into account. Additionally, although the loss minimization of some of the individual components of the drive train has been studied, the drive train as a whole has received less attention. Furthermore, as a wind turbine will typically operate at a power level lower than the nominal most of the time, efficiency analysis in the nominal operating point is not sufficient. This doctoral dissertation attempts to combine the two aforementioned areas of interest by studying the applicability of time domain simulations in the analysis of the economicfeasibility of a wind turbine. The utilization of a general-purpose time domain simulator, otherwise applied to the study of network interactions and control systems, in the economic analysis of the wind energy conversion system is studied. The main benefits of the simulation-based method over traditional methods based on analytic calculation of losses include the ability to reuse and recombine existing models, the ability to analyze interactions between the components and subsystems in the electric drive train (something which is impossible when considering different subsystems as independent blocks, as is commonly done in theanalytical calculation of efficiencies), the ability to analyze in a rather straightforward manner the effect of selections other than physical components, for example control algorithms, and the ability to verify assumptions of the effects of a particular design change on the efficiency of the whole system. Based on the work, it can be concluded that differences between two configurations can be seen in the economic performance with only minor modifications to the simulation models used in the network interaction and control method study. This eliminates the need ofdeveloping analytic expressions for losses and enables the study of the system as a whole instead of modeling it as series connection of independent blocks with no lossinterdependencies. Three example cases (site matching, component selection, control principle selection) are provided to illustrate the usage of the approach and analyze its performance.

Convergence and divergence in global economy and social development : global perspectives on the contents of economic and soical development policy and its effects on rich and poor countries

The study of convergence and divergence in global economy and social development utilises comparative indicators to investigate the contents of economic and social development policy and their effects on the global samples that represent the rich industrial, semi-industrial and the poor developing nations. The study searchesfor answers to questions such as "what are the objectives of economic growth policies in globalisation under the imperatives of convergence and divergence, and how do these affect human well-being in consideration to the objectives of social policy in various nations?" The empirical verification of data utilises the concepts of the `logic of industrialism´ for comparative analysis that focuses mainly on identifying the levels of well-being in world nations after the Second World War. The perspectives of convergence and divergence in global economy and social development critically examine the stages of early development processes in global economy, distinguish the differences between economy and social development, illustrate the contents of economic and social development policies, their effects on rich and poor countries, and the nature of convergence and divergence in propelling economic growth and unequal social development in world nations. The measurement of convergence and divergence in global economy and social development utilised both economic and social data that were combined into an index that measures the precise levels of the effects of economic and social development policies on human well-being in the rich and poor nations. The task of finding policy solutions to resolve the controversies are reviewed through empirical investigations and the analyses of trends indicated within economic and social indicators and data. These revealed how the adoption of social policy measures in translating the gains from economic growth, towards promoting education, public health, and equity, generate social progress and longer life expectancy, higher economic growth, and sustain more stable macro economy for the nations. Social policy is concerned with the translation of benefits from objectives of global economic growth policies, to objectives of social development policy in nation states. Social policy, therefore, represents an open door whereby benefits of economic growth policies are linked with the broader objectives of social development policy, thereby enhancing the possibility of extending benefits from economic growth to all human being in every nation.

Economic Geographical Analysis of The Finnish Paper Industry

The purpose of this academic economic geographical dissertation is to study and describe how competitiveness in the Finnish paper industry has developed during 2001–2008. During these years, the Finnish paper industry has faced economically challenging times. This dissertation attempts to fill the existing gap between theoretical and empirical discussions concerning economic geographical issues in the paper industry. The main research questions are: How have the supply chain costs and margins developed during 2001–2008? How do sales prices, transportation, and fixed and variable costs correlate with gross margins in a spatial context? The research object for this case study is a typical large Finnish paper mill that exports over 90 % of its production. The economic longitudinal research data were obtained from the case mill’s controlled economic system and, correlation (R2) analysis was used as the main research method. The time series data cover monthly economic and manufacturing observations from the mill from 2001 to 2008. The study reveals the development of prices, costs and transportation in the case mill, and it shows how economic variables correlate with the paper mills’ gross margins in various markets in Europe. The research methods of economic geography offer perspectives that pay attention to the spatial (market) heterogeneity. This type of research has been quite scarce in the research tradition of Finnish economic geography and supply chain management. This case study gives new insight into the research tradition of Finnish economic geography and supply chain management and its applications. As a concrete empirical result, this dissertation states that the competitive advantages of the Finnish paper industry were significantly weakened during 2001–2008 by low paper prices, costly manufacturing and expensive transportation. Statistical analysis expose that, in several important markets, transport costs lower gross margins as much as decreasing paper prices, which was a new finding. Paper companies should continuously pay attention to lowering manufacturing and transporting costs to achieve more profitable economic performance. The location of a mill being far from markets clearly has an economic impact on paper manufacturing, as paper demand is decreasing and oversupply is pressuring paper prices down. Therefore, market and economic forecasting in the paper industry is advantageous at the country and product levels while simultaneously taking into account the economic geographically specific dimensions.

Economic viability of retrofiting emitters in center pivot irrigation systems

Although several studies have been conducted to evaluate the uniformity of water application under center pivot irrigation systems, there are few studies concerning the economic perspective of such coefficient. The aim of this study is to present a methodology to accomplish an economic analysis as support for the decision-making to retrofit emitters in center pivot irrigation systems, and to attribute an economic meaning to the uniformity coefficient of water application taking into account the response function productivity to the amount of water applied and the sale price of the crops. In the hypothetic calculation example considering the variation of revenue of potato crop under center pivot irrigation system, it was verified that the area with uniformity coefficient of water application of 90% brought an income increase of BR$ 1,992.00, considering an area about 1,0 ha. Thus, it can be concluded that the methodology presented has met the objectives proposed in the study and made it possible to attribute an economical meaning to the coefficient of water uniformity application.

Technical and economic analysis of replacing artificial lighting system to induction of photoperiod effect in begonia's seedlings in greenhouse

The type of artificial light used for inducing photoperiod effect in begonia's seedlings at greenhouse has fundamental importance in the growth and development of these plants and directly reflects in the electrical energy consumption used in this production process. The objective of this research was to analyze the technical and economic feasibility of replacing the current technology of artificial lighting used by the producers (incandescent lamps), by the technology of discharge lamps with the purpose of inducing photoperiod in a greenhouse. The analysis results indicate that the discharge lamp of 32 W Tubular Fluorescent discharge lamp was the one that presented the lower peak demand and lower average energy consumption of 85.01% compared to incandescent filament lamp of 100 W that is the technology of bigger consumption and currently used by the producer.

Technical and economic analysis of irrigation of asparagus bean in protected environment

This experiment was conducted in Lavras - state of Minas Gerais (MG), Brazil, in a protected environment, and aims to estimate the irrigation depths that maximize productivity and economic returns in the cultivation of asparagus bean and analyze the economic viability of irrigation management. The experimental delineation was randomized blocks with five treatments and four replications. The treatments consisted of five drip irrigation depths: 40, 70, 100, 130 and 160% of water replacement depth up to field capacity. The depths of water that maximize productivity and economic returns were obtained from the regression model adjusted to productivity data, cost of product relations and water cost. The economic viability was achieved on the benefit/cost ratio basis. The depth with the maximum economic return was estimated in 434.4mm, with a productivity of 35,160.6kg ha-1, which is economically viable for the cultivation of asparagus bean, with a expected profitability of R$ 1.70 for every real invested.

Economic analysis of cashew early dwarf Crop BRS - 189 depending on water levels and doses of potassium fertilization

Water and fertilizer among the production factors are the elements that most restrict the production of cashew. The precise amount of these factors is essential to the success of the crop yield. This research aimed to determine the best factor-product ratio and analyze technical and economic indicators, of productivity of the cashew clone BRS 189 (Anacardium occidentale) to production factors water and potassium. The experiment was conducted from May 2009 to December 2009 in an experimental area of 56.0 m x 112.0 m in the irrigated Curu - Pentecoste, located in the municipality of Pentecoste, Ceará, Brazil. Production factors water (W) and potassium (K) were the independent variables and productivity (Y), the dependent variable. Ten statistical models that have proven satisfactory for obtaining production function were tested. The marginal rate of substitution was obtained through the ratio of the potassium marginal physical product and the water marginal physical product. The most suited model to the conditions of the experiment was the quadratic polynomial without intercept and interaction. Considering that the price of the water was 0.10 R$ mm -1, the price of the potassium 2.19 R$ kg -1 and the price of the cashew 0.60 R$ kg-1, the amounts of water and K2O to obtain the maximum net income were 6,349.1 L plant-1 of water and 128.7 g plant -1year, -1 respectively. Substituting the values obtained in the production function, the maximum net income was achieved with a yield of 7,496.8 kg ha-1 of cashew.

Technical and economic indicators of the yellow passion fruit tree irrigated with underground water supply

The research aimed to quantify technical and economic indicators of yellow passion fruit tree irrigated with fractions of irrigation with underground source of water, to generate information that helps farmers in decision making on the implementation of investment in irrigated fruit growing (yellow passion fruit). For this purpose, we used the passion fruit crop irrigated with Microjet type irrigation system, with conducting system in simple espaliers. The treatments consisted of five hours of application of the depth of water required by the crop with irrigation frequency of two days. The results showed that the highest yield (16660kg ha-1) was obtained with the fractionation of irrigation twice a day (50% to 7h and 50% to 21h30), which provided an increase in productivity of 54%, demonstrating the financial viability and being highly profitable to the interest rate of 2% per year, with low sensitivity of financial risk to real interest rates above the prevailing market.

Economic analysis for sizing of sugarcane (Saccharum spp.) mechanized harvesting

Sugarcane has a significant role on Brazilian agribusiness economy. The harvesting cane is considered as one of the most important operations of the process for it has to attend the raw material demanded by the sugar mill in quality and a competitive cost. The objective of this work it is it of analyzing, of systemic way, the variables influence on economical and operational performance in sugarcane mechanized harvesting process for sizing of machines. For this purpose a model called "ColheCana", was developed in a spreadsheet and in a programming language. The results showed that the field efficiency and harvester´s initial value are variables of great impact in the cost and that there is a maximum area that one equipment can attend and for this area the cost is minimum.

Technical-economic analysis of different lighting systems for broiler poultry

ABSTRACT Broiler poultry is highly dependent on artificial lightening. Power consumption costs of artificial lighting systems is the second largest expense related to broiler industry, second only to feed expenses. Therefore, the current study focused to analyze technical and economic feasibility of replacing incandescent lamps already used in aviaries with other lamp types. Costs related to power consumption, implementation and maintenance of the lighting systems were evaluated with the aid of financial mathematics using net present value, return over investment and payback. Systems composed of six lamp types were analyzed in two different configurations to meet the minimum illuminance of 5 and 20 lux and for use in conventional sheds and dark house. The lamps tested were incandescent (LI) of 100 W, compact fluorescent (CFL) of 34 W, mixed (ML) 160 W sodium vapor (SVL) of 70 W, tubular fluorescent T8 (TFL T8) of 40 W and tubular fluorescent T5 (TFL T5) of 28 W. For the systems tested, it was found that the tubular fluorescent lamps T8 and T5 showed the best results of technical and economic feasibility.

Techno-Economic Feasibility of Novel On-Line Condition Monitoring Methods in Low Voltage Distribution Networks

The focus in this thesis is to study both technical and economical possibilities of novel on-line condition monitoring techniques in underground low voltage distribution cable networks. This thesis consists of literature study about fault progression mechanisms in modern low voltage cables, laboratory measurements to determine the base and restrictions of novel on-line condition monitoring methods, and economic evaluation, based on fault statistics and information gathered from Finnish distribution system operators. This thesis is closely related to master’s thesis “Channel Estimation and On-line Diagnosis of LV Distribution Cabling”, which focuses more on the actual condition monitoring methods and signal theory behind them.

An Infant with Food Allergy and Eczema in the Family – The Mental and Economic Burden of Caring

Allergic diseases including food allergy and eczema in an infant in combination with the everyday activities of caring for a family will pose challenges to parents. Only fragments of these challenges are revealed to health care professionals. Families have varying mental, social and economic resources to help them care for an allergic infant, and all such resources are important in determining how families succeed in meeting these challenges and the quality of the infant’s care. This study evaluated the whole burden to the family caused by an infant's allergic disease during the first 24 months of life. As the primary caregiver during this period is usually the mother, her perspective was considered important. Ecocultural theory, which considers families as capable of modifying the positive and negative forces facing them, was taken as the frame of reference. Data were collected as part of an ongoing prospective mother-infant study, and the methods included severity scoring of atopic dermatitis, dietary records, health-related quality of life measurements and assessments of the use of health care services and medications for treating the infant’s eczema, food allergy and asthma. Interviews with mothers were analysed by deductive content analysis on the basis of ecocultural theory and the family empowerment model. The theme “Living an ordinary family life” guided the organization of family activities essential for treating the infant's food allergy and eczema. These activities were sources of both strain and support for the mothers, the allergy-related supporting factors being the mother’s own knowledge of the allergy, hopes for an improvement in the infant’s condition, social support and work. An infant’s food allergy at the age of one year caused considerable strain for the mother in cases where the introduction of new foods into the child’s diet was delayed. This delay was still causing the mother additional strain when the child was 24 months of age. The infants waking at night at the ages of 12 and 24 months because of itching related to eczema caused strain for the mothers. The infants’ health-related quality of life was impaired at ages of 6 and 12 months compared with healthy infants. The principal reasons for impairments were itching, scratching and sleep disturbances at 6 and 12 months and treatment difficulties at 6 months. Problems with getting to sleep were reported at all stages irrespective of eczema and were also present in healthy infants. The economic impact of the treatment of allergic diseases on families during the first 24 months was 131 EUR (2006 value) in cases of eczema and 525 EUR in cases of food allergy. From the societal perspective, the costs of food allergy were a median of 3183 EUR (range 628–11 560 EUR) and of eczema a median of 275 EUR (range 94–1306 EUR). These large variations in costs in food allergy and eczema indicate that disease varies greatly . In conclusion, food allergy and eczema cause extra activities and costs to families which arrange these disease-related activities in such a way that they support the leading family theme “Living an ordinary family life”. Health care professionals should consider this thematic character of family life and disease-related activities in order to ensure that new treatments are sustainable, meaningful and tailored to daily activities. In addition, those mothers who are experiencing difficulties with food allergic infants or infants with eczema should be recognized early and provided with individual encouragement and support from health clinics. In the light of the present results, early detection of symptoms and effective parental guidance can contribute to the well-being and health-related quality of life of the child and family.

Centre for Economic Development, Transport and the Environment : Prosperity, competitiveness, sustainable development

Broschure of Centre for Economic Development, Transport and the Environment.

Strategy for 2012–2015 : The Centres for Economic Development, Transport and the Environment create sustainable well-being

ELY Centres strategy brocshure.