Current mortars in conservation: an overview

Renders are an important item in historical buildings and the need for their periodical re-application is a basic conservation procedure. In modern times there has been a trend towards the replacement of traditional pure lime mortars by new formulations including Portland cement or hydraulic lime. Apart from those interventions on specific and very important monuments, in which the use oftraditional non-hydraulic mortars can be enforced, in most of the projects involving less than first order magnitude heritage the use of some sort of hydraulic components is becoming the rule rather than the exception. The present paper describes and analyses the results of an experimental study with ten formulations of current mortars - including some that can hardly be considered as adequate conservation procedures - allowing a direct comparison in terms of some of the most relevant characteristics.

Control of a power supply with cycling current using different controllers

Fast Field Cycling (FFC) Nuclear Magnetic Resonance (NMR) relaxometers require controlled current sources in order to get accurate flux density with respect to its magnet. The main elements of the proposed solution are a power semiconductor, a DC voltage source and the magnet. The power semiconductor is commanded in order to get a linear control of the flux density. To implement the flux density control, a Hall Effect sensor is used. Furthermore, the dynamic behavior of the current source is analyzed and compared when using a PI controller and a PD2I controller.

Modular high-current generator for electromagnetic forming with energy recovery

A 10 kJ electromagnetic forming (EMF) modulator with energy recovery based on two resonant power modules, each containing a 4.5 kV/30-kA silicon controlled rectifier, a 1.11-mF capacitor bank and an energy recovery circuit, working in parallel to allow a maximum actuator discharge current amplitude and rate of 50 kA and 2 kA/mu s was successfully developed and tested. It can be plugged in standard single phase 230 V/16 A mains socket and the circuit is able to recover up to 32% of its initial energy, reducing the charging time of conventional EMF systems by up to 68%.

Occupational stress and coping resources in physiotherapists: a survey of physiotherapists in three general hospitals

Objectives - To identify occupational stressors and coping resources in a group of physiotherapists, and to analyse interactions between subjective levels of stress, efficacy in stress resolution and coping resources used by these professionals. Design - A sample of 55 physiotherapists working in three general hospitals in Portugal completed the Coping Resources Inventory for Stress, the Occupational Stressors Inventory and two subjective scales for stress and stress resolution. Main results - Most physiotherapists perceived that they were moderately stressed (19/55, 35%) or stressed (20/55, 36%) due to work, and reported that their efficacy in stress resolution was moderate (25/54, 46%) or efficient (23/54, 42%). Issues related to lack of professional autonomy, lack of organisation in the hierarchical command chain, lack of professional and social recognition, disorganisation in task distribution and interpersonal conflicts with superiors were identified as the main sources of stress. The most frequently used coping resources were social support, stress monitoring, physical health and structuring. Perceived efficacy in stress resolution was inversely related to perceived level of occupational stress (r = −0.61, P < 0.01). Significant correlations were found between several coping resources and the perceived level of stress and efficacy in stress resolution. Associations between problem solving, cognitive restructuring and stress monitoring and both low levels of perceived stress and high levels of perceived efficacy were particularly strong. Implications for practice - The importance of identifying stressors and coping resources related to physiotherapists’ occupational stress, and the need for the development of specific training programmes to cope with stress are supported.

A survey of technologies and applications for climbing robots locomotion and adhesion

The interest in the development of climbing robots has grown rapidly in the last years. Climbing robots are useful devices that can be adopted in a variety of applications, such as maintenance and inspection in the process and construction industries. These systems are mainly adopted in places where direct access by a human operator is very expensive, because of the need for scaffolding, or very dangerous, due to the presence of an hostile environment. The main motivations are to increase the operation efficiency, by eliminating the costly assembly of scaffolding, or to protect human health and safety in hazardous tasks. Several climbing robots have already been developed, and other are under development, for applications ranging from cleaning to inspection of difficult to reach constructions. A wall climbing robot should not only be light, but also have large payload, so that it may reduce excessive adhesion forces and carry instrumentations during navigation. These machines should be capable of travelling over different types of surfaces, with different inclinations, such as floors, walls, or ceilings, and to walk between such surfaces (Elliot et al. (2006); Sattar et al. (2002)). Furthermore, they should be able of adapting and reconfiguring for various environment conditions and to be self-contained. Up to now, considerable research was devoted to these machines and various types of experimental models were already proposed (according to Chen et al. (2006), over 200 prototypes aimed at such applications had been developed in the world by the year 2006). However, we have to notice that the application of climbing robots is still limited. Apart from a couple successful industrialized products, most are only prototypes and few of them can be found in common use due to unsatisfactory performance in on-site tests (regarding aspects such as their speed, cost and reliability). Chen et al. (2006) present the main design problems affecting the system performance of climbing robots and also suggest solutions to these problems. The major two issues in the design of wall climbing robots are their locomotion and adhesion methods. With respect to the locomotion type, four types are often considered: the crawler, the wheeled, the legged and the propulsion robots. Although the crawler type is able to move relatively faster, it is not adequate to be applied in rough environments. On the other hand, the legged type easily copes with obstacles found in the environment, whereas generally its speed is lower and requires complex control systems. Regarding the adhesion to the surface, the robots should be able to produce a secure gripping force using a light-weight mechanism. The adhesion method is generally classified into four groups: suction force, magnetic, gripping to the surface and thrust force type. Nevertheless, recently new methods for assuring the adhesion, based in biological findings, were proposed. The vacuum type principle is light and easy to control though it presents the problem of supplying compressed air. An alternative, with costs in terms of weight, is the adoption of a vacuum pump. The magnetic type principle implies heavy actuators and is used only for ferromagnetic surfaces. The thrust force type robots make use of the forces developed by thrusters to adhere to the surfaces, but are used in very restricted and specific applications. Bearing these facts in mind, this chapter presents a survey of different applications and technologies adopted for the implementation of climbing robots locomotion and adhesion to surfaces, focusing on the new technologies that are recently being developed to fulfill these objectives. The chapter is organized as follows. Section two presents several applications of climbing robots. Sections three and four present the main locomotion principles, and the main "conventional" technologies for adhering to surfaces, respectively. Section five describes recent biological inspired technologies for robot adhesion to surfaces. Section six introduces several new architectures for climbing robots. Finally, section seven outlines the main conclusions.

Trends in healthy life expectancy among older Brazilian women between 1998 and 2008

OBJECTIVE To analyze conditional and unconditional healthy life expectancy among older Brazilian women.METHODS This cross-sectional study used the intercensal technique to estimate, in the absence of longitudinal data, healthy life expectancy that is conditional and unconditional on the individual’s current health status. The data used were obtained from the Pesquisa Nacional por Amostra de Domicílios (National Household Sample Survey) of 1998, 2003, and 2008. This sample comprised 11,171; 13,694; and 16,259 women aged 65 years or more, respectively. Complete mortality tables from the Brazilian Institute of Geography and Statistics for the years 2001 and 2006 were also used. The definition of health status was based on the difficulty in performing activities of daily living.RESULTS The remaining lifetime was strongly dependent on the current health status of the older women. Between 1998 and 2003, the amount of time lived with disability for healthy women at age 65 was 9.8%. This percentage increased to 66.2% when the women already presented some disability at age 65. Temporal analysis showed that the active life expectancy of the women at age 65 increased between 1998-2003 (19.3 years) and 2003-2008 (19.4 years). However, life years gained have been mainly focused on the unhealthy state.CONCLUSIONS Analysis of conditional and unconditional life expectancy indicated that live years gained are a result of the decline of mortality in unhealthy states. This pattern suggests that there has been no reduction in morbidity among older women in Brazil between 1998 and 2008.

Lack of access and continuity of adult health care: a national population-based survey

OBJECTIVE To describe the lack of access and continuity of health care in adults.METHODS A cross-sectional population-based study was performed on a sample of 12,402 adults aged 20 to 59 years in urban areas of 100 municipalities of 23 states in the five Brazilian geopolitical regions. Barriers to the access and continuity of health care and were investigated based on receiving, needing and seeking health care (hospitalization and accident/emergency care in the last 12 months; care provided by a doctor, by other health professional or home care in the last three months). Based on the results obtained by the description of the sample, a projection is provided for adults living in Brazilian urban areas.RESULTS The highest prevalence of lack of access to health services and to provision of care by health professionals was for hospitalization (3.0%), whilst the lowest prevalence was for care provided by a doctor (1.1%). The lack of access to care provided by other health professionals was 2.0%; to accident and emergency services, 2.1%; and to home care, 2.9%. As for prevalences, the greatest absolute lack of access occurred in emergency care (more than 360,000 adults). The main reasons were structural and organizational problems, such as unavailability of hospital beds, of health professionals, of appointments for the type of care needed and charges made for care.CONCLUSIONS The universal right to health care in Brazil has not yet been achieved. These projections can help health care management in scaling the efforts needed to overcome this problem, such as expanding the infrastructure of health services and the workforce.

ERICA: smoking prevalence in Brazilian adolescents

ABSTRACT OBJECTIVE To estimate the prevalences of tobacco use, tobacco experimentation, and frequent smoking among Brazilian adolescents. METHODS We evaluated participants of the cross-sectional, nation-wide, school-based Study of Cardiovascular Risks in Adolescents (ERICA), which included 12- to 17-year-old adolescents from municipalities of over 100 thousand inhabitants. The study sample had a clustered, stratified design and was representative of the whole country, its geographical regions, and all 27 state capitals. The information was obtained with self-administered questionnaires. Tobacco experimentation was defined as having tried cigarettes at least once in life. Adolescents who had smoked on at least one day over the previous 30 days were considered current cigarette smokers. Having smoked cigarettes for at least seven consecutive days was an indicator for regular consumption of tobacco. Considering the complex sampling design, prevalences and 95% confidence intervals were estimated according to sociodemographic and socio-environmental characteristics. RESULTS We evaluated 74,589 adolescents. Among these, 18.5% (95%CI 17.7-19.4) had smoked at least once in life, 5.7% (95%CI 5.3-6.2) smoked at the time of the research, and 2.5% (95%CI 2.2-2.8) smoked often. Adolescents aged 15 to 17 years had higher prevalences for all indicators than those aged 12 to 14 years. The prevalences did not differ significantly between sexes. The highest prevalences were found in the South region and the lowest ones, in the Northeast region. Regardless of sex, the prevalences were found to be higher for adolescents who had had paid jobs, who lived with only one parent, and who reported having been in contact with smokers either inside or outside their homes. Female public school adolescents were found to smoke more than the ones from private schools. CONCLUSIONS Tobacco use among adolescents is still a challenge. Intending to reduce the prevalence of tobacco use among young people, especially the ones under socioeconomic vulnerability conditions, Brazil must consolidate and increase effective public health care measures.

Do outro lado da linha: impacto dos horários de trabalho de trabalhadores de call center nas necessidades de recuperação – engagement e esforço compensatório

Dissertação apresentada ao Instituto Politécnico do Porto para obtenção do Grau de Mestre em Gestão das Organizações, Ramo Gestão de Empresas Orientada por: Profª Doutora Maria Alexandra Pacheco Ribeiro da Costa Esta dissertação inclui as críticas e sugestões feitas pelo Júri.

Study on the growth promoting capacity of calf and fetal bovine serum for animal cells "in vitro" II: electrophoretic study and survey on the antiproteolytic activity of pools of calf and fetal bovine serum

Calf serum and fetal bovine serum present great variability as to its growth promoting efficiency (GPE). As supplement of culture media to cultivate cells of animal origin they stimulate the "in vitro" multiplication and maintain cell viability. When fourteen lots of calf sera of variable GPE had the total protein contents as well as the percentages of serum fractions determined, no significant differences that could possibly explain the variability of the GPE were observed. Evaluation of the antiproteolytic activity of nineteen lots of calf serum and eighteen serum lots of younger calves showed that the former exhibited lower antiproteolytic titers (1:40 to 1:80) than the latter (1:80 to 1:160). Twelve lots of fetal bovine serum studied in parallel, showed the highest concentration of antiproteolytic factors, with titers equal to 1:320. Sera of bovine origin, but not fetal sera, are usually heat-inactivated, what was demonstrated to be responsible for the decrease of the antiproteolytic activity of 75% of the lots tested. This could explain the inability of certain heat-inactivated sera in promoting multiplication of some cells "in vitro", as verified with primary monkey kidney cells. The results obtained in this study indicated the convenience of submiting each lot of serum to be introduced in cell culture to previous determination of its characteristics, such as growth promoting efficiency, antiproteolytic activity and also toxicity, absence of extraneous agents, etc., in order to minimize the possibility of using serum lots of questionable quality, thus preventing not only the loss of cell lines, but also undesirable and sometimes expensive delays.

Survey on the clinical trial results achieved in Brazil comparing praziquantel and oxamniquine in the treatment of mansoni schistosomiasis

A random, double-blind, parallel group clinical trial program was carried out to compare praziquantel, a recently developed anti-helmintic drug, and oxamniquine, an already established agent for treating mansoni schistosomiasis. Both drugs were administered orally as a single dose, on the average, praziquantel 55 mg/kg and oxamniquine 16 mg/kg BWT. The diagnosis and the parasitological follow-up lasting for a minimum of six months, were based on stool examinations according to Kato/Katz technique. A patient was considered cured if all results were negative and if he had performed at least three post-treatment controls, each one comprising three stool examinations. The finding of a single S. mansoni egg in any stool examination indicated, a therapeutical failure. A total of 267, cases were treated with praziquantel and 272 with oxamniquine. The two groups were homogeneous in regard to patients, age, clinical form of the disease, risk of reinfection and worm burden, relevant factors in the therapeutical response. The incidence and severity of untoward, effects were similar in both groups but abdominal distress and diarrhoea were more frequently reported under praziquantel and dizzines under oxamniquine (p < 0.05). In the former group a marked urticariform reaction was observed whereas in the latter one patient presented convulsion. The laboratory work-up. failed to disclose any significant alteration although the AST, ALT and y-GT mean values revealed a tendence to increase on the 7th day after oxamniquine intake. The overall parasitological cure rates were 75.5% (139/ 184) with praziquantel and 69.8% (134/192) with oxamniquine (p > 0.05). Amongst the noncured aptients a reduction of 88.6% and 74.6% in the mean number of eggs/g of feces Was seen following the treatment with praziquantel and oxamniquine, respectively (p < 0.05). In conclusion, in spite of their different chemical, pharmacological and toxicological profiles as well as mechanisms-of-action, inclusively praziquantel already had proved to be 100% active against S. mansoni strains resistant to oxamniquine, both drugs showed comparable tolerance and therapeutical efficacy.

Climbing robots: a survey of technologies and applications

The interest in the development of climbing robots is growing rapidly. Motivations are typically to increase the operation efficiency by obviating the costly assembly of scaffolding or to protect human health and safety in hazardous tasks. Climbing robots are starting to be developed for applications ranging from cleaning to inspection of difficult to reach constructions. These robots should be capable of travelling on different types of surfaces, with varying inclinations, such as floors, walls, ceilings, and to walk between such surfaces. Furthermore, these machines should be capable of adapting and reconfiguring for various environment conditions and to be self-contained. Regarding the adhesion to the surface, they should be able to produce a secure gripping force using a light-weight mechanism. This paper presents a survey of different applications and technologies proposed for the implementation of climbing robots.

Estudo de uma instalação de climatização adiabática

Esta dissertação teve como objetivo o estudo de uma central de climatização adiabática, que tem como finalidade controlar a temperatura e a humidade de um salão com equipamentos de torcedura e de bobinagem, pertencente à Continental - ITA. Foi realizado um levantamento de dados relativamente à temperatura e humidade interior e exterior do referido salão. Verificou-se que estes parâmetros não estavam dentro dos valores ótimos desejados, 26 ± 1˚C e 50 ± 5%, e por isso foi necessário estimar as necessidades nominais de arrefecimento. Este valor foi determinado a partir do Regulamento das Características de Comportamento Térmico dos Edifícios (RCCTE), obtendo-se o valor de 79 kWh/m2.˚C. No sentido de avaliar se as centrais de climatização instaladas no salão em estudo satisfaziam estas necessidades, calcularam-se as suas capacidades de arrefecimento obtendo-se um valor máximo de 64 kWh/m2.˚C. Paralelamente a este estudo, foi calculada a eficiência de humidificação para cada central nos meses de março e setembro. Os valores obtidos foram oscilantes obtendo-se um valor máximo de 100% em setembro. Este fato deve-se à temperatura exterior neste mês ser mais alta e, por consequência, a eficiência de humidificação da central é maior, pois a quantidade de água que o ar pode conter na sua composição é também mais elevada. Com o objetivo de colmatar a diferença entre as necessidades nominais de arrefecimento e a capacidade de arrefecimento das centrais, foram analisadas algumas soluções que, a serem implementadas, poderiam ajudar na poupança energética. Uma dessas soluções era a substituição do sistema atual de humidificação por um sistema mais eficiente de alta pressão. Com o estudo económico deste investimento obteve-se um período de retorno de dois anos. Foram ainda apresentados mais dois investimentos onde foi alterado o sistema de controlo automático existente, obtendo-se para um, dois anos de período de retorno e para o outro três anos e meio.

A influência dos sistemas de recompensas sobre a satisfação no trabalho

Mestrado em Contabilidade e Gestão das Instituições Financeiras

E-learning frameworks: a survey

In recent years the concept of eLearning Framework emerged associated with several initiatives promoted by educational organizations. These initiatives share a common goal: to create flexible learning environments by integrating heterogeneous systems already available in many educational institutions. The paper provides an introductory survey on eLearning Frameworks. It gathers information on these initiatives categorizes them and compares their features regarding a set of predefined criteria such as: architecture, business model, primary user groups, technical implementations, adopted standards, maturity and future development.