Análisis comparativo de procedimientos para la medición de las gemas y evaluación de su influencia en la determinación de las propiedades mecánicas de la madera de Pinus sylvestris L. de gran escuadría. Comparison of wanes measurement systems to evaluate their influence on the mechanical properties of large cross section timber of Pinus sylvestris L.

Las gemas se evalúan mediante la norma de clasificación visual (UNE 56544), pero su aplicación en estructuras existentes y grandes escuadrías resulta poco eficaz y conduce a estimaciones demasiado conservadoras. Este trabajo analiza la influencia de las gemas comparando la resistencia de piezas con gemas y piezas correctamente escuadradas. Se han analizado 218 piezas de pino silvestre con dimensiones nominales 150 x 200 x 4.200 mm, de las que 102 presentaban una gema completa a lo largo de toda su longitud y el resto estaban correctamente escuadradas. En las piezas con gema se ha medido la altura de la sección cada 30 cm (altura en cada cara y altura máxima). Para determinar la resistencia se han ensayado todas las piezas de acuerdo a la norma EN 408. Se ha comparado la resistencia obtenida para las piezas con gema, diferenciando si la gema se encuentra en el borde comprimido o en el borde traccionado, con las piezas escuadradas. Puede concluirse que la presencia de gemas disminuye la resistencia excepto si la gema se encuentra en el borde traccionado, en cuyo caso los resultados obtenidos han sido similares a los de las piezas escuadradas. The wanes on structural timber are evaluated according to the visual grading standard (UNE 56544), but its application on existing structures and large cross sections is ineffective and leads to conservative estimations. This paper analyzes the influence of the wanes by comparing the resistance of pieces with wanes and square pieces. 218 pieces of Scotch pine with nominal dimensions 150 x 200 x 4200 mm have been analyzed, 102 of them had a complete wane along its length and the rest were properly squared. The height of the cross section was measured every 30 cm (the height on each side and the maximum height) for the pieces with wane. The bending strength of all the pieces was obtained according to the EN 408 standard. The bending strength of the pieces with wane has been compared with the strength of the squared pieces, taking into account if the wane is positioned on the compressed edge or on the tensioned edge. It can be concluded that the bending strength of the pieces with wanes is lower than the one of squared pieces, except if the wanes are on the tensioned edge of the beam.

Durabilidad de los bloques de tierra comprimida : Evaluación y recomendaciones para la normalización de los ensayos de erosión y absorción

La presente tesis continúa una línea de investigación iniciada en el 2006, centrada en el estudio de nuevas soluciones constructivas que toman la tierra cruda como base. Se pretende la difusión de los resultados obtenidos con el fin de fomentar estas técnicas constructivas, como por ejemplo, los sistemas de eco-construcción. El empleo de tierra cruda como sistema constructivo presenta grandes ventajas; entre ellas, un bajo impacto medioambiental, la capacidad de integración en el paisaje y un menor consumo energético. Con el fin de superar los inconvenientes que presenta el empleo de la tierra como elemento constructivo y afianzar su valor como posible material para la edificación, se estudian las propiedades de durabilidad de la misma y se dan pautas para una posible normativa futura. Se ha llevado a cabo un análisis exhaustivo de las normativas internacionales, estudiando los ensayos propuestos por los diferentes Organismos Internacionales de Normalización para caracterizar la durabilidad de los materiales de tierra. Ante la gran diversidad y heterogeneidad de las especificaciones encontradas en los ensayos que se aplican para un mismo fin, se han desarrollado dispositivos lo suficientemente versátiles para la ejecución de los ensayos propuestos. El conjunto de ensayos desarrollados en esta tesis, ha permitido elaborar una guía de recomendaciones para ensayos aplicados a materiales de tierra cruda. Además, se han estudiado las diferencias de comportamiento de los bloques de tierra comprimidos (BTC) fabricados en España, evaluando su viabilidad como material de construcción. Esta tesis ayuda a consolidar el papel de la tierra cruda en el panorama de edificación actual, solventando las dudas de los técnicos en cuanto a la durabilidad frente al agua y ausencia de normativa. Por tanto, las conclusiones sobre ensayos de durabilidad en materiales de tierra y las mejoras propuestas en algunos ensayos, sirven de referencia para la determinación de la durabilidad en los materiales basados en tierra cruda. De igual manera, es también un objetivo de la tesis que los resultados obtenidos aporten una visión general del estado normativo de los materiales a base de tierra cruda e información útil a aportar para la elaboración de documentos reconocidos sobre tierra en nuestro país, concretamente, apoyando la labor de normalización llevada a cabo en el subcomité de AENOR. This thesis continues a research line begun in 2006, focused on the study of new building solutions based on unbaked earth. With the aim to promote these construction techniques, it seeks the diffusion of the result obtained, for example eco-building systems. The use of unbaked earth as building system has great advantages such as low environmental impact, integrate ability into the landscape and lower energy consumption. In order to overcome the disadvantages of the use of earth as a building element and consolidate its value as possible building material, it is studied the properties of its durability and it is given guidelines for possible future standard. It has carried out an exhaustive analysis of international standards, studying the tests proposed by several International Organizations of Standards in order to characterize the durability of earth materials. Because of the great diversity and heterogeneity of the specifications found in the tests that are applied for the same purpose, we have developed devices versatile enough for the implementation of the proposed tests. The set of developed tests in this thesis has allowed developing a recommendation guideline for tests applied to unbaked earth materials. In addition, we have studied the differences of behavior of compressed earth blocks (CEB) manufactured in Spain, evaluating its viability as building material. This thesis helps to consolidate the role of unbaked earth in the scene of current building, solving the doubts of technicians about durability against rain and lack of standard. Therefore, the conclusions of durability tests in earth materials and the proposed improvements in some tests, serve as a reference for determining the durability of the materials based on raw earth. In the same way, it is also an objective of the thesis that the obtained results provide an overview of standards status of materials based on unbaked earth and useful information for the development documents recognized on earth in our country, supporting the standardization that is taking place at the subcommittee AENOR.

Relativistic high-current electron-beam stopping-power characterization in solids and plasmas: collisional versus resistive effects.

We present experimental and numerical results on intense-laser-pulse-produced fast electron beams transport through aluminum samples, either solid or compressed and heated by laser-induced planar shock propagation. Thanks to absolute K� yield measurements and its very good agreement with results from numerical simulations, we quantify the collisional and resistive fast electron stopping powers: for electron current densities of � 8 � 1010 A=cm2 they reach 1:5 keV=�m and 0:8 keV=�m, respectively. For higher current densities up to 1012 A=cm2, numerical simulations show resistive and collisional energy losses at comparable levels. Analytical estimations predict the resistive stopping power will be kept on the level of 1 keV=�m for electron current densities of 1014 A=cm2, representative of the full-scale conditions in the fast ignition of inertially confined fusion targets.

Differences in the structural response of 'granny-smith' apples under mechanical impact and compression

Apple fruits, cv. Granny Smith, were subjected to mechanical impact and compression loads utilizing a steel rod with a spherical tip 19 mm diameter, 50.6 g mass. Energies applied were low enough to produce enzymatic reaction: 0.0120 J for impact, and 0.0199 J for compression. Bruised material was cut and examined with a transmission electron microscope. In both compression and impact, bruises showed a central region located in the flesh parenchyma, at a distance that approximately equalled the indentor tip radius. The parenchyma cells of this region were more altered than cells from the epidermis and hypodermis. Tissues under compression presented numerous deformed parenchyma cells with broken tonoplasts and tissue degradation as predicted by several investigators. The impacted cells supported different kinds of stresses than compressed cells, resulting in the formation of intensive vesiculation, either in the vacuole or in the middle lamella region between cell walls of adjacent cells. A large proportion of parenchyma cells completely split or had initiated splitting at the middle lamella. Bruising may develop with or without cell rupture. Therefore, cell wall rupture is not essential for the development of a bruise, at least the smallest one, as predicted previously

Compression of matter by hypersphsericla shock waves

A novel compression scheme is proposed, in which hollow targets with specifically curved structures initially filled with uniform matter, are driven by converging shock waves. The self-similar dynamics is analyzed for converging and diverging shock waves. The shock-compressed densities and pressures are much higher than those achieved using spherical shocks due to the geometric accumulation. Dynamic behavior is demonstrated using two-dimensional hydrodynamic simulations. The linear stability analysis for the spherical geometry reveals a new dispersion relation with cut-off mode numbers as a function of the specific heat ratio, above which eigenmode perturbations are smeared out in the converging phase.

Comparative study of auxetic geometrics by means of computer-aided design and engineering

Auxetic materials (or metamaterials) are those with a negative Poisson ratio (NPR) and display the unexpected property of lateral expansion when stretched, as well as an equal and opposing densification when compressed. Such geometries are being progressively employed in the development of novel products, especially in the fields of intelligent expandable actuators, shape morphing structures and minimally invasive implantable devices. Although several auxetic and potentially auxetic geometries have been summarized in previous reviews and research, precise information regarding relevant properties for design tasks is not always provided. In this study we present a comparative study of two-dimensional and three-dimensional auxetic geometries carried out by means of computer-aided design and engineering tools (from now on CAD–CAE). The first part of the study is focused on the development of a CAD library of auxetics. Once the library is developed we simulate the behavior of the different auxetic geometries and elaborate a systematic comparison, considering relevant properties of these geometries, such as Poisson ratio(s), maximum volume or area reductions attainable and equivalent Young's modulus, hoping it may provide useful information for future designs of devices based on these interesting structures.

On the flexural vibration of cylinders under axial loads:Numerical and experimental study

The flexural vibration of a homogeneous isotropic linearly elastic cylinder of any aspect ratio is analysed in this paper. Natural frequencies of a cylinder under uniformly distributed axial loads acting on its bases are calculated numerically by the Ritz method with terms of power series in the coordinate directions as approximating functions. The effect of axial loads on the flexural vibration cannot be described by applying infinitesimal strain theory, therefore, geometrically nonlinear strain–displacement relations with second-order terms are considered here. The natural frequencies of free–free, clamped–clamped, and sliding–sliding cylinders subjected to axial loads are calculated using the proposed three-dimensional Ritz approach and are compared with those obtained with the finite element method and the Bernoulli–Euler theory. Different experiments with cylinders axially compressed by a hydraulic press are carried out and the experimental results for the lowest flexural frequency are compared with the numerical results. An approach based on the Ritz formulation is proposed for the flexural vibration of a cylinder between the platens of the press with constraints varying with the intensity of the compression. The results show that for low compressions the cylinder behaves similarly to a sliding–sliding cylinder, whereas for high compressions the cylinder vibrates as a clamped–clamped one.

Approximation to earth material from international normative

For centuries, earth has been used as a construction material. Nevertheless, the normative in this matter is very scattered, and the most developed countries, to carry out a construction with this material implies a variety of technical and legal problems. In this paper we review, in an international level, the normative panorama about earth constructions. It analyzes ninety one standards and regulations of countries all around the five continents. These standards represent the state of art that normalizes the earth as a construction material. In this research we analyze the international standards to earth construction, focusing on durability test (spray and drip erosion tests). It analyzes the differences between methods of test. Also we show all results about these tests in two types of compressed earth block.

A novel methodology to determine the mechanical properties of amorphous materials through instrumented nanoindentation

A novel methodology based on instrumented indentation was developed to characterize the mechanical properties of amorphous materials. The approach is based on the concept of a universal postulate that assumes the existence of a characteristic indentation pressure proportional to the hardness. This hypothesis was numerically validated. This method overcomes the limitation of the conventional indentation models (pile-up effects and pressure sensitivity materials).

Corrección del deslizamiento de una ladera en la autovia A-4. PK. 340 en el término municipal de Marmolejo, Jaén mediante pantalla de pilotes y sistemas de drenaje

En este proyecto se describe el cálculo y diseño de una serie de medidas correctoras propuestas a raíz de un deslizamiento de ladera que tuvo lugar en noviembre de 2010 y afectó a parte de la calzada de la autovía A-4 en el P.K. 340 entre Córdoba y Jaén; principalmente en la ejecución de una pantalla de pilotes como elemento estructural de estabilización y contención del terreno, por medio del método de equilibrio límite y cálculo del módulo de reacción o coeficiente de balasto horizontal, a través del empleo de los programas Slope/W y RIDO respectivamente. ABSTRACT This project describes the calculation and design of a series of proposed corrective measures following a landslide of which took place in November 2010 and hit part of the road A-4 on the P.K. 340 between Cordoba and Jaen, mainly in the execution of a pile wall as a structural element of stabilization and containment of the terrain, through the limit equilibrium method and calculating the reaction module or horizontal ballast coefficient, through employment of the Slope/W and RIDO programs respectively.

Combining a Similar Coefficient Identification Algorithm with the Boundary Element Method

The boundary element method (BEM) has been applied successfully to many engineering problems during the last decades. Compared with domain type methods like the finite element method (FEM) or the finite difference method (FDM) the BEM can handle problems where the medium extends to infinity much easier than domain type methods as there is no need to develop special boundary conditions (quiet or absorbing boundaries) or infinite elements at the boundaries introduced to limit the domain studied. The determination of the dynamic stiffness of arbitrarily shaped footings is just one of these fields where the BEM has been the method of choice, especially in the 1980s. With the continuous development of computer technology and the available hardware equipment the size of the problems under study grew and, as the flop count for solving the resulting linear system of equations grows with the third power of the number of equations, there was a need for the development of iterative methods with better performance. In [1] the GMRES algorithm was presented which is now widely used for implementations of the collocation BEM. While the FEM results in sparsely populated coefficient matrices, the BEM leads, in general, to fully or densely populated ones, depending on the number of subregions, posing a serious memory problem even for todays computers. If the geometry of the problem permits the surface of the domain to be meshed with equally shaped elements a lot of the resulting coefficients will be calculated and stored repeatedly. The present paper shows how these unnecessary operations can be avoided reducing the calculation time as well as the storage requirement. To this end a similar coefficient identification algorithm (SCIA), has been developed and implemented in a program written in Fortran 90. The vertical dynamic stiffness of a single pile in layered soil has been chosen to test the performance of the implementation. The results obtained with the 3-d model may be compared with those obtained with an axisymmetric formulation which are considered to be the reference values as the mesh quality is much better. The entire 3D model comprises more than 35000 dofs being a soil region with 21168 dofs the biggest single region. Note that the memory necessary to store all coefficients of this single region is about 6.8 GB, an amount which is usually not available with personal computers. In the problem under study the interface zone between the two adjacent soil regions as well as the surface of the top layer may be meshed with equally sized elements. In this case the application of the SCIA leads to an important reduction in memory requirements. The maximum memory used during the calculation has been reduced to 1.2 GB. The application of the SCIA thus permits problems to be solved on personal computers which otherwise would require much more powerful hardware.

Sistema de instrumentação e controle para células a combustível

Este trabajo presenta un estudio sobre el funcionamiento y aplicaciones de las células de combustible de membrana tipo PEM, o de intercambio de protones, alimentadas con hidrógeno puro y oxigeno obtenido de aire comprimido. Una vez evaluado el proceso de dichas células y las variables que intervienen en el mismo, como presión, humedad y temperatura, se presenta una variedad de métodos para la instrumentación de tales variables así como métodos y sistemas para la estabilidad y control de las mismas, en torno a los valores óptimos para una mayor eficacia en el proceso. Tomando como variable principal a controlar la temperatura del proceso, y exponiendo los valores concretos en torno a 80 grados centígrados entre los que debe situarse, es realizado un modelo del proceso de calentamiento y evolución de la temperatura en función de la potencia del calentador resistivo en el dominio de la frecuencia compleja, y a su vez implementado un sistema de medición mediante sensores termopar de tipo K de respuesta casi lineal. La señal medida por los sensores es amplificada de manera diferencial mediante amplificadores de instrumentación INA2126, y es desarrollado un algoritmo de corrección de error de unión fría (error producido por la inclusión de nuevos metales del conector en el efecto termopar). Son incluidos los datos de test referentes al sistema de medición de temperatura , incluyendo las desviaciones o error respecto a los valores ideales de medida. Para la adquisición de datos y implementación de algoritmos de control, es utilizado un PC con el software Labview de National Instruments, que permite una programación intuitiva, versátil y visual, y poder realizar interfaces de usuario gráficas simples. La conexión entre el hardware de instrumentación y control de la célula y el PC se realiza mediante un interface de adquisición de datos USB NI 6800 que cuenta con un amplio número de salidas y entradas analógicas. Una vez digitalizadas las muestras de la señal medida, y corregido el error de unión fría anteriormente apuntado, es implementado en dicho software un controlador de tipo PID ( proporcional-integral-derivativo) , que se presenta como uno de los métodos más adecuados por su simplicidad de programación y su eficacia para el control de este tipo de variables. Para la evaluación del comportamiento del sistema son expuestas simulaciones mediante el software Matlab y Simulink determinando por tanto las mejores estrategias para desarrollar el control PID, así como los posibles resultados del proceso. En cuanto al sistema de calentamiento de los fluidos, es empleado un elemento resistor calentador, cuya potencia es controlada mediante un circuito electrónico compuesto por un detector de cruce por cero de la onda AC de alimentación y un sistema formado por un elemento TRIAC y su circuito de accionamiento. De manera análoga se expone el sistema de instrumentación para la presión de los gases en el circuito, variable que oscila en valores próximos a 3 atmosferas, para ello es empleado un sensor de presión con salida en corriente mediante bucle 4-20 mA, y un convertidor simple corriente a tensión para la entrada al sistema de adquisición de datos. Consecuentemente se presenta el esquema y componentes necesarios para la canalización, calentamiento y humidificación de los gases empleados en el proceso así como la situación de los sensores y actuadores. Por último el trabajo expone la relación de algoritmos desarrollados y un apéndice con información relativa al software Labview. ABTRACT This document presents a study about the operation and applications of PEM fuel cells (Proton exchange membrane fuel cells), fed with pure hydrogen and oxygen obtained from compressed air. Having evaluated the process of these cells and the variables involved on it, such as pressure, humidity and temperature, there is a variety of methods for implementing their control and to set up them around optimal values for greater efficiency in the process. Taking as primary process variable the temperature, and exposing its correct values around 80 degrees centigrade, between which must be placed, is carried out a model of the heating process and the temperature evolution related with the resistive heater power on the complex frequency domain, and is implemented a measuring system with thermocouple sensor type K performing a almost linear response. The differential signal measured by the sensor is amplified through INA2126 instrumentation amplifiers, and is developed a cold junction error correction algorithm (error produced by the inclusion of additional metals of connectors on the thermocouple effect). Data from the test concerning the temperature measurement system are included , including deviations or error regarding the ideal values of measurement. For data acquisition and implementation of control algorithms, is used a PC with LabVIEW software from National Instruments, which makes programming intuitive, versatile, visual, and useful to perform simple user interfaces. The connection between the instrumentation and control hardware of the cell and the PC interface is via a USB data acquisition NI 6800 that has a large number of analog inputs and outputs. Once stored the samples of the measured signal, and correct the error noted above junction, is implemented a software controller PID (proportional-integral-derivative), which is presented as one of the best methods for their programming simplicity and effectiveness for the control of such variables. To evaluate the performance of the system are presented simulations using Matlab and Simulink software thereby determining the best strategies to develop PID control, and possible outcomes of the process. As fluid heating system, is employed a heater resistor element whose power is controlled by an electronic circuit comprising a zero crossing detector of the AC power wave and a system consisting of a Triac and its drive circuit. As made with temperature variable it is developed an instrumentation system for gas pressure in the circuit, variable ranging in values around 3 atmospheres, it is employed a pressure sensor with a current output via 4-20 mA loop, and a single current to voltage converter to adequate the input to the data acquisition system. Consequently is developed the scheme and components needed for circulation, heating and humidification of the gases used in the process as well as the location of sensors and actuators. Finally the document presents the list of algorithms and an appendix with information about Labview software.

Medida de la conductividad térmica con el método de la aguja térmica, basado en la fuente lineal de calor transitorio, para su aplicación en los cerramientos de adobes y bloques de tierra comprimida

Existe un creciente interés internacional por el ahorro energético y la sostenibilidad en la edificación con importantes repercusiones en la Arquitectura. La inercia térmica es un parámetro fundamental para poder valorar energéticamente un edificio en condiciones reales. Para ello es necesario cambiar el enfoque tradicional de transmisión de calor en régimen estacionario por otro en régimen dinámico en el que se analizan las ondas térmicas y el flujo de calor oscilante que atraviesan los cerramientos. Los parámetros que definen la inercia térmica son: el espesor, la difusividad y el ciclo térmico. A su vez la difusividad está determinada por la conductividad térmica, la densidad y el calor específico del material. De estos parámetros la conductividad es el más complejo, variable y difícil de medir, especialmente en los cerramientos de tierra debido a su heterogeneidad y complejidad higrotérmica. En general, los métodos de medida de la conductividad o transmitancias en los paramentos presentan inconvenientes a la hora de medir un edificio construido con tierra: dificultades de implementación, el elevado coste o la fiabilidad de los resultados, principalmente. El Método de la Aguja Térmica (MAT) se basa en el principio de la evolución en el tiempo del calor emitido por una fuente lineal al insertarse en el seno de un material. Se ha escogido este método porque resulta práctico, de bajo coste y de fácil aplicación a gran escala pero tiene serios problemas de fiabilidad y exactitud. En esta tesis se desarrolla un método de medida de la conductividad térmica para Piezas de Albañilería de Tierra Cruda en laboratorio basado en el MAT, se mejora su fiabilidad, se analiza su incertidumbre, se compara con otros métodos de referencia y se aplica en adobes, Bloques de Tierra Comprimida y probetas de tierra estabilizada con distintas proporciones de paja. Este método servirá de base a una posterior aplicación in situ. Finalmente se proponen modelos matemáticos para mejorar la exactitud del dispositivo utilizado y para la estimación de la conductividad de cerramientos de tierra en función de su densidad. Con los resultados obtenidos se analizan las posibilidades de amortiguación y retardo de las ondas térmicas y capacidad de almacenaje de energía de los cerramientos en función de su densidad y humedad. There is growing international interest in energy saving and sustainability in buildings with significant impact on Architecture. Thermal inertia is a key parameter to assess energy in buildings in real conditions. This requires changing the traditional approach to heat transfer in steady state by another in dynamic regime which analyzes the thermal waves and oscillating heat flux passing through the external walls. The parameters defining the thermal inertia are: the thickness, the diffusivity and the thermal cycle. In turn, the diffusivity is determined by the thermal conductivity, density and specific heat of the material. Of these parameters, thermal conductivity is the most complex, variable and difficult to measure, especially in earth walls due to their heterogeneity and hygrothermal complexity. In general, the methods of measurement of conductivity and transmittance in walls have drawbacks when measuring a building with earth: implementation difficulties, high cost, or reliability of the results, mainly. The Thermal Needle Procedure (TNP) is based on the principle of evolution in time of heat from a line source when inserted within a material. This method was chosen because it is a practical, low cost and easy to implement on a large scale but has serious problems of reliability and accuracy. This thesis develops a laboratory method for measuring the thermal conductivity of Masonry Units Unfire Earth-based based on TNP, its uncertainty is analyzed, compared to other reference methods and applies in adobes, Compressed Earth Blocks and stabilized soil specimens with different proportions of straw. This method will form the basis of a subsequent application in situ. Finally, mathematical models are proposed to improve the accuracy of the device used, and to estimate the conductivity of earth enclosures depending on its density. With the results obtained earth enclosures are analyzed to estimate their possibilities of delay and buffer of termal waves and energy storage capacity according to their density and moisture.

Interfaz gráfica y fase de pruebas de software de vídeo forense (Sistema de codificación DV)

El presente proyecto fin de carrera, realizado por el ingeniero técnico en telecomunicaciones Pedro M. Matamala Lucas, es la fase final de desarrollo de un proyecto de mayor magnitud correspondiente al software de vídeo forense SAVID. El propósito del proyecto en su totalidad es la creación de una herramienta informática capacitada para realizar el análisis de ficheros de vídeo, codificados y comprimidos por el sistema DV –Digital Video-. El objetivo del análisis, es aportar información acerca de si la cinta magnética presenta indicios de haber sido manipulada con una edición posterior a su grabación original, además, de mostrar al usuario otros datos de interés como las especificaciones técnicas de la señal de vídeo y audio. Por lo tanto, se facilitará al usuario, analista de vídeo forense, información que le ayude a valorar la originalidad del contenido del soporte que es sujeto del análisis. El objetivo específico de esta fase final, es la creación de la interfaz de usuario del software, que informa tanto del código binario de los sectores significativos, como de su interpretación tras el análisis. También permitirá al usuario el reporte de los resultados, además de otras funcionalidades que le permitan la navegación por los sectores del código que han sido modificados como efecto colateral de la edición de la cinta magnética original. Otro objetivo importante del proyecto ha sido la investigación de metodologías y técnicas de desarrollo de software para su posterior implementación, buscando con esto, una mayor eficiencia en la gestión del tiempo y una mayor calidad de software con el fin de garantizar su evolución y sostenibilidad en el futuro. Se ha hecho hincapié en las metodologías ágiles que han ido ganando relevancia en el sector de las tecnologías de la información en las últimas décadas, sustituyendo a metodologías clásicas como el desarrollo en cascada. Su flexibilidad durante el ciclo de vida del software, permite obtener mejores resultados cuando las especificaciones no están del todo definidas, ajustándose de este modo a las condiciones del proyecto. Resumiendo las especificaciones técnicas del software, C++ es el lenguaje de programación orientado a objetos con el que se ha desarrollado, utilizándose la tecnología MFC -Microsoft Foundation Classes- para la implementación. Es un proyecto MFC de tipo cuadro de dialogo,creado, compilado y publicado, con la herramienta de desarrollo integrado Microsoft Visual Studio 2010. La arquitectura con la que se ha estructurado es la arquetípica de tres capas, compuesta por la interfaz de usuario, capa de negocio y capa de acceso a datos. Se ha visto necesario configurar el proyecto con compatibilidad con CLR –Common Languages Runtime- para poder implementar la funcionalidad de creación de reportes. Acompañando a la aplicación informática, se presenta la memoria del proyecto y sus anexos correspondientes a los documentos EDRF –Especificaciones Detalladas de Requisitos funcionales-, EIU –Especificaciones de Interfaz de Usuario , DT -Diseño Técnico- y Guía de Usuario. SUMMARY. This dissertation, carried out by the telecommunications engineer Pedro M. Matamala Lucas, is in its final stage and is part of a larger project for the software of forensic video called SAVID. The purpose of the entire project is the creation of a software tool capable of analyzing video files that are coded and compressed by the DV -Digital Video- System. The objective of the analysis is to provide information on whether the magnetic tape shows signs of having been tampered with after the editing of the original recording, and also to show the user other relevant data and technical specifications of the video signal and audio. Therefore the user, forensic video analyst, will have information to help assess the originality of the content of the media that is subject to analysis. The specific objective of this final phase is the creation of the user interface of the software that provides information about the binary code of the significant sectors and also its interpretation after analysis. It will also allow the user to report the results, and other features that will allow browsing through the sections of the code that have been modified as a secondary effect of the original magnetic tape being tampered. Another important objective of the project is the investigation of methodologies and software development techniques to be used in deployment, with the aim of greater efficiency in time management and enhanced software quality in order to ensure its development and maintenance in the future. Agile methodologies, which have become important in the field of information technology in recent decades, have been used during the execution of the project, replacing classical methodologies such as Waterfall Development. The flexibility, as the result of using by agile methodologies, during the software life cycle, produces better results when the specifications are not fully defined, thus conforming to the initial conditions of the project. Summarizing the software technical specifications, C + + the programming language – which is object oriented and has been developed using technology MFC- Microsoft Foundation Classes for implementation. It is a project type dialog box, created, compiled and released with the integrated development tool Microsoft Visual Studio 2010. The architecture is structured in three layers: the user interface, business layer and data access layer. It has been necessary to configure the project with the support CLR -Common Languages Runtime – in order to implement the reporting functionality. The software application is submitted with the project report and its annexes to the following documents: Functional Requirements Specifications - Detailed User Interface Specifications, Technical Design and User Guide.

Co2 capture in power plants-using the oxy-combustion principle

In the C02 capture from power generation, the energy penalties for the capture are one of the main challenges. Nowadays, the post-combustion methods have energy penalties 10wer than the oxy combustion and pre-combustion technologies. One of the main disadvantages of the post combustion method is the fact that the capture ofC02at atmospheric pressure requires quite big equipment for the high flow rates of flue gas, and the 10w partial pressure of the CO2generates an important 10ss of energy. The A1lam cyc1e presented for NETPOWER gives high efficiencies in the power production and 10w energy penalties. A simulation of this cyc1e is made together with a simulation of power plants with pre-combustion and post-combustion capture and without capture for natural gas and forcoa1. The simulations give 10wer efficiencies than the proposed for NETPOWER For natural gas the efficiency is 52% instead of the 59% presented, and 33% instead of51% in the case of using coal as fuel. Are brought to light problems in the CO2compressor due the high flow ofC02that is compressed unti1300 bar to be recyc1ed into the combustor.