Importance of early diagnosis of Stickler syndrome in newborns

Objective: The study aims to investigate a possible correlation between the main clinical and ophthalmological characteristics, age and Robin sequence in patients with the Stickler syndrome. Introduction: The Stickler syndrome is an autosomal dominant genetic disorder, characterised by ocular, orofacial and skeletal anomalies and/or auditory loss. Patients with Robin sequence features and respiratory complications are frequently diagnosed with the Stickler syndrome. The heterogeneous phenotypic manifestations may present a challenge for early clinical diagnosis. Methods: We performed a retrospective study of the 98 patients with the Stickler syndrome, between November 1995 and June 2009. The data were compared to investigate their ocular alterations and association with the Robin sequence. To be included, patients had to present with the following triad: cleft palate, facial features (hypoplastic midface, micrognathia and prominent eyes) and ocular anomalies (myopia and/or abnormalities of the retina). Results: Fifty-one percent of the patients presenting with Robin sequence features had been diagnosed with the Stickler syndrome. Ocular alterations were found in 50% of the patients. Discussion: The Robin sequence may appear as an isolated condition or associated with other features, or else as part of other known syndromes. Currently, the diagnosis of the Stickler syndrome is based on clinical signs. Affected individuals eventually develop hearing loss, retinal detachment and blindness. The ophthalmological complications associated are usually progressive and can lead to blindness.

Experimental investigation of gravitational gas separation in an inclined annular channel

The oil industry uses gas separators in production wells as the free gas present in the suction of the pump reduces the pumping efficiency and pump lifetime. Therefore, free gas is one of the most important variables in the design of pumping systems. However, in the literature there is little information on these separators. It is the case of the inverted-shroud gravitational gas separator. It has an annular geometry due to the installation of a cylindrical container in between the well casing and pioduction pipe (tubing). The purpose of the present study is to understand the phenomenology and behavior of inverted-shroud separator. Experimental tests were performed in a 10.5-m-length inclinable glass tube with air and water as working fluids. The water flow rate was in the range of 8.265-26.117 l/min and the average inlet air mass flow rate was 1.1041 kg/h, with inclination angles of 15 degrees, 30 degrees, 45 degrees, 60 degrees, 75 degrees, 80 degrees and 85 degrees. One of the findings is that the length between the inner annular level and production pipe inlet is one of the most important design parameters and based on that a new criterion for total gas separation is proposed. We also found that the phenomenology of the studied separator is not directly dependent on the gas flow rate, but on the average velocity of the free surface flow generated inside the separator. Maps of efficiency of gas separation were plotted and showed that liquid flow rate, inclination angle and pressure difference between casing and production pipe outlet are the main variables related to the gas separation phenomenon. The new data can be used for the development of design tools aiming to the optimized project of the pumping system for oil production in directional wells. (C) 2012 Elsevier Inc. All rights reserved.

Expression of laminin-5 and integrins in actinic cheilitis and superficially invasive squamous cell carcinomas of the lip

The progression of carcinogenesis entails the detachment of cells, invasion and migration of neoplastic cells. Alterations in epithelial adhesion and basement membrane proteins might mediate the early stages of carcinogenesis. This study investigated the expression of adhesion molecules and the basement membrane protein laminin-5 in actinic cheilitis (AC) and incipient squamous cell carcinoma of the lower lip to understand early photocarcinogenesis. Ln-5 gamma 2 chain as well as alpha 3, beta 1 subunits of alpha 3 beta 1 heterodimer and beta 4 subunit of integrin alpha 6 beta 4 were evaluated by immunohistochemistry in 16 cases of AC and 16 cases of superficially invasive squamous cell carcinoma (SISCC). Most AC cases showed reduced expression of beta 1, beta 4 and alpha 3 integrins, and SISCCs lacked beta 1, beta 4 and alpha 3 integrins in the invasive front. AC cases were negative for the Ln-5 gamma 2 chain. Five cases of SISCC (31%) showed heterogeneous Ln-5 gamma 2 chain expression in the invasive front of the tumor. Integrin beta 1, beta 4 and alpha 3 expression is lost during the early stages of lip carcinogenesis. Expression of Ln-5 gamma 2 in the invasive front in cases and its correlation with tumor progression suggest that it mediates the acquisition of the migrating and invading epithelial cell phenotype. (C) 2012 Elsevier GmbH. All rights reserved.

Glycosaminoglycans modulate C6 glioma cell adhesion to extracellular matrix components and alter cell proliferation and cell migration

Abstract Background Adhesion to extracellular matrix (ECM) components has been implicated in the proliferative and invasive properties of tumor cells. We investigated the ability of C6 glioma cells to attach to ECM components in vitro and described the regulatory role of glycosaminoglycans (GAGs) on their adhesion to the substrate, proliferation and migration. Results ECM proteins (type IV collagen, laminin and fibronectin) stimulate rat C6 glioma cell line adhesion in vitro, in a dose-dependent manner. The higher adhesion values were achieved with type IV collagen. Exogenous heparin or chondroitin sulfate impaired, in a dose-dependent manner the attachment of C6 glioma cell line to laminin and fibronectin, but not to type IV collagen. Dextran sulfate did not affect C6 adhesion to any ECM protein analyzed, indicating a specific role of GAGs in mediating glioma adhesion to laminin and fibronectin. GAGs and dextran sulfate did not induce C6 glioma detachment from any tested substrate suggesting specific effect in the initial step of cell adhesion. Furthermore, heparin and chondroitin sulfate impaired C6 cells proliferation on fibronectin, but not on type IV collagen or laminin. In contrast, both GAGs stimulate the glioma migration on laminin without effect on type IV collagen or fibronectin. Conclusion The results suggest that GAGs and proteoglycans regulate glioma cell adhesion to ECM proteins in specific manner leading to cell proliferation or cell migration, according to the ECM composition, thus modulating tumor cell properties.

Patterns of cell proliferation and apoptosis by topographic region in normal Bos taurus vs. Bos indicus crossbreeds bovine placentae during pregnancy

Background: Placental and fetal growth requires high rates of cellular turnover and differentiation, which contributes to conceptus development. The trophoblast has unique properties and a wide range of metabolic, endocrine and angiogenic functions, but the proliferative profile of the bovine placenta characterized by flow cytometry analysis and its role in fetal development are currently uncharacterized. Complete understanding of placental apoptotic and proliferative rates may be relevant to development, especially if related to the pathogenesis of pregnancy losses and placental abnormalities. Methods: In this study, the proliferation activity and apoptosis in different regions of normal bovine placenta (central and boundary regions of placentomes, placentomal fusion, microplacentomes, and interplacentomal regions), from distinct gestation periods (Days 70 to 290 of pregnancy), were analyzed by flow cytometry. Results: Our results indicated that microplacentomes presented a lower number of apoptotic cells throughout pregnancy, with a higher proliferative activity by the end of gestation, suggesting that such structures do not contribute significantly to normal of placental functions and conceptus development during pregnancy. The placentome edges revealed a higher number of apoptotic cells from Day 170 on, which suggests that placentome detachment may well initiate in this region. Conclusion: Variations involving proliferation and apoptotic rates may influence placental maturation and detachment, compromising placental functions and leading to fetal stress, abnormalities in development and abortion, as frequently seen in bovine pregnancies from in vitro fertilization and cloning procedures. Our findings describing the pattern of cell proliferation and apoptosis in normal bovine pregnancies may be useful for unraveling some of the developmental deviations seen in nature and after in vitro embryo manipulations.

Motor recovery and synaptic preservation after ventral root avulsion and repair with a fibrin sealant derived from snake venom

Background: Ventral root avulsion is an experimental model of proximal axonal injury at the central/peripheral nervous system interface that results in paralysis and poor clinical outcome after restorative surgery. Root reimplantation may decrease neuronal degeneration in such cases. We describe the use of a snake venom-derived fibrin sealant during surgical reconnection of avulsed roots at the spinal cord surface. The present work investigates the effects of this fibrin sealant on functional recovery, neuronal survival, synaptic plasticity, and glial reaction in the spinal motoneuron microenvironment after ventral root reimplantation. Methodology/Principal Findings: Female Lewis rats (7 weeks old) were subjected to VRA and root replantation. The animals were divided into two groups: 1) avulsion only and 2) replanted roots with fibrin sealant derived from snake venom. Post-surgical motor performance was evaluated using the CatWalk system twice a week for 12 weeks. The rats were sacrificed 12 weeks after surgery, and their lumbar intumescences were processed for motoneuron counting and immunohistochemistry (GFAP, Iba-1 and synaptophysin antisera). Array based qRT-PCR was used to evaluate gene regulation of several neurotrophic factors and receptors as well as inflammatory related molecules. The results indicated that the root reimplantation with fibrin sealant enhanced motor recovery, preserved the synaptic covering of the motoneurons and improved neuronal survival. The replanted group did not show significant changes in microglial response compared to VRA-only. However, the astroglial reaction was significantly reduced in this group. Conclusions/Significance: In conclusion, the present data suggest that the repair of avulsed roots with snake venom fibrin glue at the exact point of detachment results in neuroprotection and preservation of the synaptic network at the microenvironment of the lesioned motoneurons. Also such procedure reduced the astroglial reaction and increased mRNA levels to neurotrophins and anti-inflammatory cytokines that may in turn, contribute to improving recovery of motor function.

Ajuste e balanceamento do portfólio de projetos: o caso de uma empresa do setor químico

O objetivo deste trabalho é compreender a etapa de ajuste no contexto da gestão do portfólio de projetos, destacando sua relação com os processos de categorização e balanceamento. A pesquisa realizada tem caráter qualitativo, sendo a abordagem adotada o estudo de caso longitudinal. A pesquisa foi desenvolvida em uma empresa do setor químico brasileiro. As evidências, de várias fontes, foram coletadas através de entrevistas, documentos e dados dos sistemas corporativos. Para a compreensão do portfólio de projetos da empresa foram coletados e analisados dados de mil projetos realizados entre 2001 e 2005. Os resultados indicam que maior atenção é dada à etapa de seleção, negligenciando a etapa de ajuste. A adoção de ferramentas de balanceamento permitiu evidenciar lacunas e fontes de desbalanceamento no portfólio de projetos, promovendo o debate entre os tomadores de decisão no que concerne ao viés introduzido pelos critérios adotados na etapa de seleção e levantando a necessidade de introdução de uma sistemática de ajuste e balanceamento. Observou-se que sem uma adequada categorização dos projetos da empresa seria difícil promover a análise de balanceamento.

Usable work of macro-scale cavities in liquids

It is shown that the generation of cavities in a liquid can produce usable work, which is illustrated by the stretching of a string. This work is done during the expansion of the cavity, and not with its collapse. Basic equations are presented for the movement of a device moved by the so called cavity events. A theoretical solution is also proposed, which uses polynomial functions relating the so called "excess of pressure" in the cavity and time. Evaluations of the force generated during the expansion of the cavity showed a mean peak value of about 58 N for the moving container, while measurements with the container fixed to a support showed a peak value of 476 N, considered somewhat overestimated, because high frequency oscillations seem to superpose the mean behavior. Simultaneous phenomena occurring during the cavity events are also described. Series of pictures of the experiments are presented.

Effect of EVA on the fresh properties of cement paste

The improved workability effect of latex in dry mortars has not been fully clarified. The purpose of this research was to investigate the influence of the EVA copolymer on the cement hydration and on the rheological properties of cement pastes. The results pointed to a minor influence of EVA on cement hydration and to a ball-bearing effect. In fact, the shear thinning behavior of reference paste at 15 min after mixing changed to shear thickening owing to the EVA addition. This behavior could be explained by the decrease in the interparticle separation distance as consequence of the solid content increase in case of shearing detachment of weakly adhered EVA particles from the cement particles surfaces. The expected EVA plasticizing effect was observed at 60 min. Such behavior points to the stabilization of EVA on the cement particles surfaces, thus resulting in a steric barrier effect.

Two fluid numerical model for coastal applications

Wave breaking is an important coastal process, influencing hydro-morphodynamic processes such as turbulence generation and wave energy dissipation, run-up on the beach and overtopping of coastal defence structures. During breaking, waves are complex mixtures of air and water (“white water”) whose properties affect velocity and pressure fields in the vicinity of the free surface and, depending on the breaker characteristics, different mechanisms for air entrainment are usually observed. Several laboratory experiments have been performed to investigate the role of air bubbles in the wave breaking process (Chanson & Cummings, 1994, among others) and in wave loading on vertical wall (Oumeraci et al., 2001; Peregrine et al., 2006, among others), showing that the air phase is not negligible since the turbulent energy dissipation involves air-water mixture. The recent advancement of numerical models has given valuable insights in the knowledge of wave transformation and interaction with coastal structures. Among these models, some solve the RANS equations coupled with a free-surface tracking algorithm and describe velocity, pressure, turbulence and vorticity fields (Lara et al. 2006 a-b, Clementi et al., 2007). The single-phase numerical model, in which the constitutive equations are solved only for the liquid phase, neglects effects induced by air movement and trapped air bubbles in water. Numerical approximations at the free surface may induce errors in predicting breaking point and wave height and moreover, entrapped air bubbles and water splash in air are not properly represented. The aim of the present thesis is to develop a new two-phase model called COBRAS2 (stands for Cornell Breaking waves And Structures 2 phases), that is the enhancement of the single-phase code COBRAS0, originally developed at Cornell University (Lin & Liu, 1998). In the first part of the work, both fluids are considered as incompressible, while the second part will treat air compressibility modelling. The mathematical formulation and the numerical resolution of the governing equations of COBRAS2 are derived and some model-experiment comparisons are shown. In particular, validation tests are performed in order to prove model stability and accuracy. The simulation of the rising of a large air bubble in an otherwise quiescent water pool reveals the model capability to reproduce the process physics in a realistic way. Analytical solutions for stationary and internal waves are compared with corresponding numerical results, in order to test processes involving wide range of density difference. Waves induced by dam-break in different scenarios (on dry and wet beds, as well as on a ramp) are studied, focusing on the role of air as the medium in which the water wave propagates and on the numerical representation of bubble dynamics. Simulations of solitary and regular waves, characterized by both spilling and plunging breakers, are analyzed with comparisons with experimental data and other numerical model in order to investigate air influence on wave breaking mechanisms and underline model capability and accuracy. Finally, modelling of air compressibility is included in the new developed model and is validated, revealing an accurate reproduction of processes. Some preliminary tests on wave impact on vertical walls are performed: since air flow modelling allows to have a more realistic reproduction of breaking wave propagation, the dependence of wave breaker shapes and aeration characteristics on impact pressure values is studied and, on the basis of a qualitative comparison with experimental observations, the numerical simulations achieve good results.

Rapporti tra tettonica e clima durante l'esumazione nelle Alpi Centrali. Evidenze dalla termocronologia e dall'analisi strutturale lungo il traforo ferroviario del Sempione

(U-Th)/He and fission-track analyses of apatite along deep-seated tunnels crossing high-relief mountain ranges offer the opportunity to investigate climate and tectonic forcing on the topographic evolution. In this study, the thermochronologic analysis of a large set of samples collected in the Simplon railway tunnel (western-central Alps; Italy and Switzerland) and along its surface trace, coupled with kinematic and structural analysis of major fault zones intersecting the tunnel, constrains the phenomena controlling the topographic and structural evolution, during the latest stage of exhumation of the Simplon Massif, and the timing in which they operated. The study area is located at the western margin of the Lepontine metamorphic dome where a complex nappe-stack pertaining to the Penninic and Ultrahelvetic domains experienced a fast exhumation from the latest Oligocene onward. The exhumation was mainly accommodated by a west-dipping low-angle detachment (the Simplon Fault Zone) which is located just 8 km to the west of the tunnel. However, along the section itself several faults related to two principal phases both with important dip-slip kinematics have been detected. Cooling rates derived from our thermocronological data vary from about 10 °C/Ma at about 10 Ma to about 35 °C/Ma in the last 5 Ma. Such increase in the cooling rate corresponds to the most important climatic change recorded in the northern hemisphere in the last 10 Ma, i.e. the shift to wetter conditions at the end of the Messinian salinity crisis and the inception of glacial cycles in the northern hemisphere. In addition, (U-Th)/He and fission-track age patterns lack of important correlation with the topography suggesting that the present-day relief morphology is the result of recent erosional dynamics. More in details, the (U-Th)/He tunnel ages show an impressive uniformity at 2 Ma, whereas cooling rates calculated at 1 Ma increase towards the two major valleys. This indicates a focusing of erosive processes in the valleys which led to the shaping of present-day topography. Structural analysis documents the presence of two phases of brittle deformation postdating the metamorphic phases in the area. The first one is directly related to the last phase of activity along the Simplon Fault Zone and is characterized by extension towards SO and vertical shortening. The young one is characterized by extension towards NO and horizontal shortening in a along the NE-SO direction. Structures related to the first phase of brittle deformation generate important variations in the older ages' dataset, until 3 Ma, suggesting that tectonics controlled rocks exhumation up to that age. Structures related to the second phase generate some variations also in the younger age dataset, highlighting the activity of faults bordering the massif and suggesting a continuous activity also after 2 Ma. However, most of (U-Th)/He tunnel ages, varying slightly around 2 Ma, document that the Simplon area has experienced primarily erosional exhumation in this time span. In conclusion, all our data suggest that in the central Italian Alps the climatic signal gradually overrode the tectonic effects after about 5 Ma, as a consequence of the climatic instability started at end of Messinian salinity crisis and improved by the onset of glaciations in the northern hemisphere.

Study of the circulation processes in the northern Adriatic sea - coastal area and Venice lagoon inlets

This work is a detailed study of hydrodynamic processes in a defined area, the littoral in front of the Venice Lagoon and its inlets, which are complex morphological areas of interconnection. A finite element hydrodynamic model of the Venice Lagoon and the Adriatic Sea has been developed in order to study the coastal current patterns and the exchanges at the inlets of the Venice Lagoon. This is the first work in this area that tries to model the interaction dynamics, running together a model for the lagoon and the Adriatic Sea. First the barotropic processes near the inlets of the Venice Lagoon have been studied. Data from more than ten tide gauges displaced in the Adriatic Sea have been used in the calibration of the simulated water levels. To validate the model results, empirical flux data measured by ADCP probes installed inside the inlets of Lido and Malamocco have been used and the exchanges through the three inlets of the Venice Lagoon have been analyzed. The comparison between modelled and measured fluxes at the inlets outlined the efficiency of the model to reproduce both tide and wind induced water exchanges between the sea and the lagoon. As a second step, also small scale processes around the inlets that connect the Venice lagoon with the Northern Adriatic Sea have been investigated by means of 3D simulations. Maps of vorticity have been produced, considering the influence of tidal flows and wind stress in the area. A sensitivity analysis has been carried out to define the importance of the advection and of the baroclinic pressure gradients in the development of vortical processes seen along the littoral close to the inlets. Finally a comparison with real data measurements, surface velocity data from HF Radar near the Venice inlets, has been performed, which allows for a better understanding of the processes and their seasonal dynamics. The results outline the predominance of wind and tidal forcing in the coastal area. Wind forcing acts mainly on the mean coastal current inducing its detachment offshore during Sirocco events and an increase of littoral currents during Bora events. The Bora action is more homogeneous on the whole coastal area whereas the Sirocco strengthens its impact in the South, near Chioggia inlet. Tidal forcing at the inlets is mainly barotropic. The sensitivity analysis shows how advection is the main physical process responsible for the persistent vortical structures present along the littoral between the Venice Lagoon inlets. The comparison with measurements from HF Radar not only permitted a validation the model results, but also a description of different patterns in specific periods of the year. The success of the 2D and the 3D simulations on the reproduction both of the SSE, inside and outside the Venice Lagoon, of the tidal flow, through the lagoon inlets, and of the small scale phenomena, occurring along the littoral, indicates that the finite element approach is the most suitable tool for the investigation of coastal processes. For the first time, as shown by the flux modeling, the physical processes that drive the interaction between the two basins were reproduced.

The Effect of Preservative Interventions on the Chemical- Physical and Structural Characteristics of Panel Painting

This work studies the impact of two traditional Romanian treatments, Red Petroleum and Propolis, in terms of real efficiency and consequence on the wooden artifacts. The application of these solutions is still a widely adopted and popular technique in preservative conservation but the impact of these solutions is not well known. It is important to know the effect of treatments on chemical-physical and structural characteristics of the artifacts, not only for understanding the influence on present conditions but also for foreseeing the future behavior. These treatments with Romanian traditional products are compared with a commercial antifungal product, Biotin R, which is utilized as reference to control the effectiveness of Red Petroleum and Propolis. Red Petroleum and Propolis are not active against mould while Biotin R is very active. Mould attack is mostly concentrated in the painted layer, where the tempera, containing glue and egg, enhance nutrition availability for moulds. Biotin R, even if is not a real insecticide but a fungicide, was the most active product against insect attack of the three products, followed by Red Petroleum, Propolis and untreated reference. As for colour, it did not change so much after the application of Red Petroleum and Biotin R and the colour difference was almost not perceptible. On the contrary, Propolis affected the colour a lot. During the exposure at different RH, the colour changes significantly at 100% RH at equilibrium and this is mainly due to the mould attack. Red Petroleum penetrates deeply into wood, while Propolis does not penetrate and remains only on the surface. However, Red Petroleum does not interact chemically with wood substance and it is easy volatilized in oven-dry condition. On the contrary Propolis interacts chemically with wood substance and hardly volatilized, even in oven-dry condition and consequently Propolis remains where it penetrated, mostly on the surface. Treatment by immersion has impact on wood physical parameters while treatment by brushing does not have significant impact. Especially Red Petroleum has an apparent impact on moisture content (MC) due to the penetration of solution, while Propolis does not penetrate so much and remains only on surface therefore Propolis does not have so much impact as Red Petroleum. However, if the weight of the solution penetrated in wood is eliminated, there is not significant difference in MC between treated and untreated samples. Considering physical parameters, dimensional stability is an important parameter. The variation of wood moisture content causes shrinkages/swelling of the wood that polychrome layer can only partially follow. The dimension of wooden supports varied under different moisture conditioning; the painted layer cannot completely follow this deformation, and consequently a degradation and deterioration caused by detachment, occurs. That detachment affects the polychrome stratification of the panel painting and eventually the connections between the different layer compositions of the panel painting.

Correlazioni tra proprietá reologiche, struttura e processabilitá di blend di LLDPE/LDPE

Polymer blends constitute a valuable way to produce relatively low cost new materials. A still open question concerns the miscibility of polyethylene blends. Deviations from the log-additivity rule of the newtonian viscosity are often taken as a signature of immiscibility of the two components. The aim of this thesis is to characterize the rheological behavior in shear and elongation of five series of LLDPE/LDPE blends whose parent polymers have been chosen with different viscosity and SCB content and length. Synergistic effects have been measured for both zero shear viscosity and melt strength. Both SCB length and viscosity ratio between the components have been found to be key parameters for the miscibility of the pure polymers. In particular the miscibility increases with increasing SCB length and with decreasing the LDPE molecular weight and viscosity. This rheological behavior has significant effects on the processability window of these blends when the uni or biaxial elongational flows are involved. The film blowing is one of the processes for which the synergistic effects above mentioned can be crucial. Small scale experiments of film blowing performed for one of the series of blends has demonstrated that the positive deviation of the melt strength enlarges the processability window. In particular, the bubble stability was found to improve or disappear when the melt strength of the samples increased. The blending of LDPE and LLDPE can even reduce undesired melt flow instability phenomena widening, as a consequence, the processability window in extrusion. One of the series of blends has been characterized by means of capillary rheometry in order to allow a careful morphological analysis of the surface of the extruded polymer jets by means of Scanning Electron Microscopy (SEM) with the aim to detect the very early stages of the small scale melt instabilty at low shear rates (sharksin) and to follow its subsequent evolution as long as the shear rate was increased. With this experimental procedure it was possible to evaluate the shear rate ranges corresponding to different flow regions: smooth extrudate surface (absence of instability), sharkskin (small scale instability produced at the capillary exit), stick-slip transition (instability involving the whole capillary wall) and gross melt fracture (i.e. a large scale "upstream" instability originating from the entrance region of the capillary). A quantitative map was finally worked out using which an assessment of the flow type for a given shear rate and blend composition can be predicted.

Eocene nappe tectonics and late Alpine extension in the Central Anatolide belt, western Turkey

Strukturgeologische Untersuchungen belegen, daß die Anatoliden der Westtürkei im Eozän durch die Plazierung der Kykladischen Blauschiefereinheit entlang einer durchbrechenden Überschiebung auf die Menderes-Decken unter grünschieferfaziellen Metamorphosebedingungen entstanden.Die kykladischen Blauschiefer in der Westtürkei enthalten Relikte eines prograden alpinen Gefüges (DA1), welches hochruckmetamorph von Disthen und Chloritoid poikiloblastisch überwachsen wurde. Dieses Mineralstadium dauerte noch während des Beginns des nachfolgenden Deformationsereignisses (DA2) an, welches durch NE-gerichtete Scherung und Dekompression charakterisiert ist. Die nachfolgende Deformation (DA3) war das erste Ereignis, das beide Einheiten, sowohl die kykladische Blauschifereinheit als auch die Menderes-Decken, gemeinsam erfaßte. Der Überschiebungskontakt zwischen der kykladischen Blauschiefereinheit und den Menderes-Decken ist eine DA3-Scherzone: die ‘Cycladic-Menderes Thrust’ (CMT). Entlang der CMT-Überschiebungsbahn wurden die kykladischen Blauschiefer gegen veschiedene Einheiten der MN plaziert. Die CMT steigt nach S zum strukturell Hangenden hin an und kann daher als eine durchbrechende Überschiebung entlang einer nach S ansteigenden Rampe betrachtet werden. In den kykladischen Blauschiefern überprägen DA3-Strukturen, die im Zusammenhang mit der CMT stehen, hochdruckmentamorphe Gefüge.In den Menderes-Decken, dem Liegenden der CMT, wird DA3 durch regional vebreitete Gefügeelemente dokumentiert, die im Zusammenhang mit S-gerichteten Schersinnindikatoren stehen. DA3-Gefüge haben die Decken intern deformiert und bilden jene Scherzonen, welche die Decken untereinander abgrenzen. In der Çine-Decke können granitische Gesteine in Orthogneise und Metagranite unterteilt werden. Die Deformationsgeschichte dieser Gesteine dokumentiert zwei Ereignisse. Ein frühes amphibolitfazielles Ereignis erfaßte nur die Orthogneise, in denen vorwiegend NE-SW orientierte Lineare und NE-gerichtete Schersinnindikatoren entstanden. Die jüngeren Metagranite wurden sowohl durch vereinzelte DA3-Scherzonen, als auch in einer großmaßstäblichen DA3-Scherzone am Südrand des Çine-Massivs deformiert. In DA3-Scherzonen sind die Lineare N-S orientiert und die zugehörigen Schersinnindikatoren zeigen S-gerichtete Scherung unter grünschieferfaziellen Bedingungen an. Diese grünschieferfaziellen Scherzonen überprägen die amphibolitfaziellen Gefüge in den Orthogneisen. Magmatische Zirkone aus einem Metagranit, der einen Orthogneiss mit Top-NE Gefügen durchschlägt, ergaben ein 207Pb/206Pb-Alter von 547,2±1,0 Ma. Dies deutet darauf hin, daß DPA proterozoischen Alters ist. Dies wird auch durch die Tatsache gestützt, daß triassische Granite in der Çine- und der Bozdag-Decke keine DPA-Gefüge zeigen. Die jüngeren Top-S-Gefüge sind wahrscheinlich zur gleichen Zeit entstanden wie die ältesten Gefüge der Bayindir-Decke.Das Fehlen von Hochdruck-Gefügen im Liegenden der CMT impliziert eine Exhumierung der kykladischen Blauschiefer von mehr ca. 35 km, bevor diese im Eozän auf die Menderes-Decken aufgeschoben wurden. Die substantiellen Unterschiede bezüglich in der tektonometamorphen Geschichte der kykladischen Blauschiefer und der Menderes-Decken widersprechen der Modellvorstellung eines lateral kontinuierlichen Orogengürtels, nach der die Menderes-Decken als östliche Fortsezung der kykladischen Blauschiefer angesehen werden.Die Analyse spröder spätalpiner Deformationsstrukturen und das regionale Muster mit Hilfe von Spaltspurdatierung modellierter Abkühlalter deuten darauf hin, daß die Struktur des Eozänen Deckenstapels durch miozäne bis rezente Kernkomplex-Bildung stark modifiziert wurde. Eine großmaßstäbliche Muldenstruktur im zentralen Teil der Anatoliden hat sich als Folge zweier symmetrisch angeordneter Detachment-Systeme von initial steilen zu heute flachen Orientierungen im Einflußbreich von ’Rolling Hinges’ gebildet. Die Detachment-Störungen begrenzen den ‘Central Menderes metamorphic core complex’ (CMCC). Das Muster der Apatit-Spaltspuralter belegt, daß die Bildung des CMCC im Miozän begann. Durch die Rück-Deformierung von parallel zur Foliation konstruierten Linien gleicher Abkühlalter kann gezeigt werden, daß die Aufwölbung im Liegenden der Detachments zur Entstehung der Muldenstruktur führte. Das hohe topographische Relief im Bereich des CMCC ist eine Folge der Detachment-Störungen, was darauf hindeutet daß der obere Mantel in den Prozeß mit einbezogen gewesen ist.