Comparison of different breast planning techniques and algorithms for radiation therapy treatment

This work aims at investigating the impact of treating breast cancer using different radiation therapy (RT) techniques – forwardly-planned intensity-modulated, f-IMRT, inversely-planned IMRT and dynamic conformal arc (DCART) RT – and their effects on the whole-breast irradiation and in the undesirable irradiation of the surrounding healthy tissues. Two algorithms of iPlan BrainLAB treatment planning system were compared: Pencil Beam Convolution (PBC) and commercial Monte Carlo (iMC). Seven left-sided breast patients submitted to breast-conserving surgery were enrolled in the study. For each patient, four RT techniques – f-IMRT, IMRT using 2-fields and 5-fields (IMRT2 and IMRT5, respectively) and DCART – were applied. The dose distributions in the planned target volume (PTV) and the dose to the organs at risk (OAR) were compared analyzing dose–volume histograms; further statistical analysis was performed using IBM SPSS v20 software. For PBC, all techniques provided adequate coverage of the PTV. However, statistically significant dose differences were observed between the techniques, in the PTV, OAR and also in the pattern of dose distribution spreading into normal tissues. IMRT5 and DCART spread low doses into greater volumes of normal tissue, right breast, right lung and heart than tangential techniques. However, IMRT5 plans improved distributions for the PTV, exhibiting better conformity and homogeneity in target and reduced high dose percentages in ipsilateral OAR. DCART did not present advantages over any of the techniques investigated. Differences were also found comparing the calculation algorithms: PBC estimated higher doses for the PTV, ipsilateral lung and heart than the iMC algorithm predicted.

Contribuição para a caracterização da emissão de nanopartículas em processos de soldadura e avaliação de riscos decorrentes do processo

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química e Biológica Ramo de processos químicos

Desenvolvimento do conceito de ângulo: um estudo no 5.ºano de escolaridade

A investigação em curso visa compreender a influência da implementação de um conjunto de tarefas no desenvolvimento do conceito de ângulo em alunos do 5.º ano de escolaridade, procurando responder às seguintes questões: a) Que conceções revelam alunos do 5.º ano de escolaridade relativamente ao conceito de ângulo?; b) Que estratégias utilizam os alunos do 5.º ano de escolaridade na exploração das tarefas utilizadas?; e c) Que aspetos do conceito de ângulo são desenvolvidos pelos alunos através da realização das tarefas propostas? A presente comunicação incide na primeira questão do estudo. Optou-se por uma abordagem metodológica qualitativa de paradigma interpretativo com a modalidade de experiência de ensino. Selecionou-se quatro alunos para constituir o grupo-alvo. Procedeu-se à avaliação diagnóstica das conceções de ângulo dos quatro alunos através da realização, no 1.º Período do ano letivo de 2011/12, de entrevistas clínicas semiestruturadas individuais, gravadas em vídeo. Além das entrevistas, foram usadas, como técnicas de recolha de dados, a observação participante das aulas, videogravadas, bem como a análise de documentos. Para analisar os dados, foram elaboradas categorias analíticas. Os resultados relativos à avaliação diagnóstica evidenciam conceções erradas de ângulo e respetiva amplitude: (a) os ângulos são os lados de polígonos (1 aluna); (b) o comprimento dos segmentos representativos dos lados está relacionado com o tamanho dos ângulos (2 alunos); (c) o comprimento do arco marcando o ângulo está relacionado com o tamanho dos ângulos (3 alunos); (d) nos polígonos côncavos, sãoângulos apenas os de amplitude inferior a 1800 (3 alunos); (e) em figuras que não são polígonos, os ângulos são os espaços entre os segmentos de reta e as linhas curvas (1 aluno); (f) o ângulo é a área entre dois segmentos representativos dos lados (4 alunos); e (g) os ângulos retos são apenas os posicionados na posição usual horizontal/vertical (1 aluna).

Characterization of airborne particles generated from metal active gas welding process

This study is focused on the characterization of particles emitted in the metal active gas welding of carbon steel using mixture of Ar + CO2, and intends to analyze which are the main process parameters that influence the emission itself. It was found that the amount of emitted particles (measured by particle number and alveolar deposited surface area) are clearly dependent on the distance to the welding front and also on the main welding parameters, namely the current intensity and heat input in the welding process. The emission of airborne fine particles seems to increase with the current intensity as fume-formation rate does. When comparing the tested gas mixtures, higher emissions are observed for more oxidant mixtures, that is, mixtures with higher CO2 content, which result in higher arc stability. These mixtures originate higher concentrations of fine particles (as measured by number of particles by cm 3 of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more severe worker's exposure.

Principais dificuldades que os alunos de viola de arco apresentam quando ingressam no ensino superior português: relatório de estágio

A maioria dos instrumentistas de cordas friccionadas apresentam problemas ou dificuldades ao longo de toda a sua aprendizagem musical. Como professora e violetista, realizei este relatório de estágio com o intuito de pesquisar onde se focam a maioria desses problemas. Este relatório de estágio está dividido em duas diferentes secções, a primeira apresenta todo o trabalho pedagógico efectuado com três diferentes alunos, de diferentes níveis ao longo do ano lectivo de 2012/13 na Fundação Musical dos Amigos das Crianças (FMAC), e a segunda apresenta toda a investigação que realizei para concluir quais as principais dificuldades que os alunos de viola de arco apresentam quando ingressam no Ensino Superior. A investigação apresenta uma vasta pesquisa literária e o testemunho dos professores de várias instituições, como a Universidade do Minho, Escola Superior de Música e Artes de Espectáculo, Universidade de Aveiro, Escola Superior das Artes Aplicadas de Castelo Branco e Escola Superior de Música de Lisboa que ajudaram à profunda análise deste tema. Os resultados revelaram que os principais problemas apresentados nos estudantes de viola de arco são de origem técnica, ou seja, postura (posição do corpo, distribuição do peso correcto pelas pernas e escolha adequada do instrumento de acordo com a fisionomia do aluno); mão direita (pega correcta dos dedos no arco, distribuição de arco e contracção muscular); mão esquerda (posição do polegar, ombro e braço que afectam a afinação, flexibilidade, mudanças de posição e vibrato); influência da escolha do repertório por parte de um professor e autonomia do aluno.

On the choice of posittioning and cluster size for fixed relay stations in a LTE network

The long term evolution (LTE) is one of the latest standards in the mobile communications market. To achieve its performance, LTE networks use several techniques, such as multi-carrier technique, multiple-input-multiple-output and cooperative communications. Inside cooperative communications, this paper focuses on the fixed relaying technique, presenting a way for determining the best position to deploy the relay station (RS), from a set of empirical good solutions, and also to quantify the associated performance gain using different cluster size configurations. The best RS position was obtained through realistic simulations, which set it as the middle of the cell's circumference arc. Additionally, it also confirmed that network's performance is improved when the number of RSs is increased. It was possible to conclude that, for each deployed RS, the percentage of area served by an RS increases about 10 %. Furthermore, the mean data rate in the cell has been increased by approximately 60 % through the use of RSs. Finally, a given scenario with a larger number of RSs, can experience the same performance as an equivalent scenario without RSs, but with higher reuse distance. This conduces to a compromise solution between RS installation and cluster size, in order to maximize capacity, as well as performance.

The effect of metal transfer modes and shielding gas composition on the emission of ultraafine particles in MAG steel welding

The present study aims to characterize ultrafine particles emitted during gas metal arc welding of mild steel and stainless steel, using different shielding gas mixtures, and to evaluate the effect of metal transfer modes, controlled by both processing parameters and shielding gas composition, on the quantity and morphology of the ultrafine particles. It was found that the amount of emitted ultrafine particles (measured by particle number and alveolar deposited surface area) are clearly dependent from the main welding parameters, namely the current intensity and the heat input of the Welding process. The emission of airborne ultrafine particles increases with the current intensity as fume formation rate does. When comparing the shielding gas mixtures, higher emissions were observed for more oxidizing mixtures, that is, with higher CO2 content, which means that these mixtures originate higher concentrations of ultrafine particles (as measured by number of particles. by cubic centimeter of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more hazardous condition regarding welders exposure.

Emission of airborne ultrafine particles during welding of steel plates

The present study is focused on the characterization of ultrafine particles emitted in welding of steel using mixtures of Ar+CO2, and intends to analyze which are the main process parameters which may have influence on the emission itself. It was found that the amount of emitted ultrafine particles (measured by particle number and alveolar deposited surface area) are clearly dependent from the distance to the welding front and also from the main welding parameters, namely the current intensity and heat input in the welding process. The emission of airborne ultrafine particles seem to increase with the current intensity as fume formation rate does. When comparing the tested gas mixtures, higher emissions are observed for more oxidant mixtures, that is, mixtures with higher CO2 content, which result in higher arc stability. The later mixtures originate higher concentrations of ultrafine particles (as measured by number of particles by cm3 of air) and higher values of alveolar deposited surface area of particles, thus resulting in a more hazardous condition regarding worker's exposure. © 2014 Sociedade Portuguesa de Materiais (SPM). Published by Elsevier España, S.L. All rights reserved.

The effect of metal transfer stability (spattering) on fume generation, morphology and composition in short-circuit MAG welding

The main objective of this work was to evaluate the hypothesis that the greater transfer stability leads also to less volume of fumes. Using an Ar + 25%CO2 blend as shielding gas and maintaining constant the average current, wire feed speed and welding speed, bead-on-plate welds were carried out with plain carbon steel solid wire. The welding voltage was scanned to progressively vary the transfer stability. Using two conditions of low stability and one with high stability, fume generation was evaluated by means of the AWS F1.2:2006 standard. The influence of these conditions on fume morphology and composition was also verified. A condition with greater transfer stability does not generate less fume quantity, despite the fact that this condition produces fewer spatters. Other factors such as short-circuit current, arcing time, droplet diameters and arc length are the likely governing factors, but in an interrelated way. Metal transfer stability does not influence either the composition or the size/morphology of fume particulates. (c) 2014 Elsevier B.V. All rights reserved.

Immunodiagnostic confirmation of hydatid disease in patients with a presumptive diagnosis of infection

Information obtained from the routine application of hydatid immunodiagnostic techniques in different clinical situations over a seven-year period is presented. The Immunoelectrophoresis test was used until it was replaced by the simpler, more sensitive and equally specific arc 5 double diffusion (DD5) test. Examination of sera from 1,888 patients with signs and/or symptoms compatible with hydatid disease revealed that the presurgical confirmation of Echinococcus granulosus infection is only obtained by detection of anti-antigen 5 antibodies. The latter were not found in 1,539 presumptive hydatidosis patients whose definitive diagnoses corresponded to other disease conditions. However, false positive latex agglutination test results were obtained in two cases. In all patients whose preoperative serum showed three or more uncharacteristic bands in the absence of anti-antigen 5 antibodies, hydatid cysts were found sur gically. DD5 testing of a fluid sample collected by puncture established its hydatid etiology. Post-operative monitoring of hydatidosis patients demonstrated that persistence of DD5-positivity two years after surgery established the presence of other cysts. Further evidence was obtained in patients with hydatid cysts in intrathoracic, abdominal or other locations associating cyst membrane integrity, antigen release and immunodiagnostic test positivity.

Reinfecções por rotavírus em crianças de Belém, Pará, Brasil

Reinfecções por rotavírus foram detectadas em 7 (9,2%) de 76 crianças habitantes da periferia de Belém, Pará, Brasil, no decurso de seus primeiros 20 meses de vida. A presença de rotavírus classificados no subgrupo II ("long pattern") foi assinalada, tanta na primeira como segunda infecções, em cinco desses indivíduos. Em duas situações, a primeira infecção foi causada por rotavírus subgrupo II e, a reinfecção, por rotavírus de subgrupo não claramente caracterizado. Seis diferentes padrões foram observados, não ocorrendo casos em que, numa única criança, se tenham assinalado perfis homólogos. O maior intervalo de tempo registrado entre duas infecções no mesmo indivíduo foi de 19 meses, enquanto que o menor, de 6. Formas sintomáticas em ambos os processos infecciosos se apresentaram em cinco crianças; em duas, os primeiros episódios revelaram-se assintomáticos, sucedendo-se quadros diarréicos. Em seis dos sete indivíduos, observaram-se soroconversões para rotavírus durante a segunda infecção; durante a primeira, entretanto, a elevação significativa nos níveis de anticorpos grupo-específicos se registrou em apenas um caso (Paciente F).

Reinfections and rotavirus serotypes in Belém, Brazil

Repeated infections involving different rotavirus serotypes were detected in four children living in Belém, who were followed up since birth to three years of age. In one child (Reg. 23.983) three successive symptomatic infections (one of them associated with serotype 2) were noted: the first, at four months of age, the second at 20 months and the third at 27 months. Another child had two subsequent infections, the first one by rotavirus serotype 1, and the second by a not identified rotavirus serotype. In this case two episodes of rotavirus-related diarrhoea were recorded, occurring eight months apart. Apparent infections were detected on two occasions involving the same child (Reg. 24.004), the first being associated with serotype 1, and the second with serotype 2. The fourth child (Reg. 24.097) had two successive infections by not determined rotavirus serotypes, without clinical manifestations; the first occurred at 24 months and the second at 28 months.

Performance indexes of a dot-enzime-linked immunosorbent assay (dot-ELISA) and an ezyme-linked immunosorbent assay (IgG-ELISA) for field surveys of new world leishmaniasis

Diagnostic performance indexes of sensitivity, specificity, positive predictive value and efficiency were determined for dot-ELISA and IgG-ELISA tests in 340 leishmaniasis sera. Sensitivity of the dot-ELISA was significantly lower than IgG-ELISA's; the two tests had indexes of specificity and positive predictive value of the same magnitude. Seventy-eight sera gave a negative dot-ELISA test result and a positive IgG-ELISA test result. When sera were classified according to different criteria as how to interpret this diversity, the kappa statistic did not corroborate the classification indicating that the two tests display a substantial strength of agreement. The results presented indicate that performance indexes accrued in a survey where variables arc well known may be extrapolated to other population studies if the disease presents itself as highly prevalent (due to a selection bias or not) and may be expected to discriminate a disease status among test positives.

Assessment and control of nanoparticles exposure in welding operations by use of a control banding tool

This paper describes the use of a Control Banding Tool to assess and further control of exposure of nanoparticles emitted during welding operations. The tool was applied to Metal Active Gas (MAG) arc welding of mild and stainless steel, providing semi-quantitative data on the process, so that protection measures could be derived, e.g. exhaust gas ventilation by hoods, local ventilation devices and containment measures. This tool is quite useful to compare and evaluate the characteristics of arc welding procedures so that more eco-friendly processes could be preferred over the more potentially noxious ones.

From the Bay of Biscay to the High Atlas: completing the anisotropic characterization of the upper mantle beneath the westernmost Mediterranean region

The knowledge of the anisotropic properties beneath the Iberian Peninsula and Northern Morocco has been dramatically improved since late 2007 with the analysis of the data provided by the dense TopoIberia broadband seismic network, the increasing number of permanent stations operating in Morocco, Portugal and Spain, and the contribution of smaller scale/higher resolution experiments. Results from the two first TopoIberia deployments have evidenced a spectacular rotation of the fast polarization direction (FPD) along the Gibraltar Arc, interpreted as an evidence of mantle flow deflected around the high velocity slab beneath the Alboran Sea, and a rather uniform N100 degrees E FPD beneath the central Iberian Variscan Massif, consistent with global mantle flow models taking into account contributions of surface plate motion, density variations and net lithosphere rotation. The results from the last Iberarray deployment presented here, covering the northern part of the Iberian Peninsula, also show a rather uniform FPD orientation close to N100 degrees E, thus confirming the previous interpretation globally relating the anisotropic parameters to the LPO of mantle minerals generated by mantle flow at asthenospheric depths. However, the degree of anisotropy varies significantly, from delay time values of around 0.5 s beneath NW Iberia to values reaching 2.0 sin its NE comer. The anisotropic parameters retrieved from single events providing high quality data also show significant differences for stations located in the Variscan units of NW Iberia, suggesting that the region includes multiple anisotropic layers or complex anisotropy systems. These results allow to complete the map of the anisotropic properties of the westernmost Mediterranean region, which can now be considered as one of best constrained regions worldwide, with more than 300 sites investigated over an area extending from the Bay of Biscay to the Sahara platform. (C) 2015 Elsevier B.V. All rights reserved.